SCC-C7478 36x Smart Dome Camera User’s Guide ENG FRE GER SPA ITA imagine the possibilities Thank you for purchasing this Samsung product. To receive more complete service, please register your product at www.samsung.
Safety information CAUTION RISK OF ELECTRIC SHOCK. DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE REAR COVER. NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.. This symbol indicates high voltage is present inside. It is dangerous to make any kind of contact with any inside part of this product. This symbol alerts you that important literature concerning operation and maintenance has been included with this product.
Safety information CAUTION 1. Do not drop objects on the product or apply strong shock to it. Keep away from a location subject to excessive vibrationor magnetic interference. 2. Do not install in a location subject to high temperature (over 50°C), low temperature (below -10°C), or high humidity. Doing so may cause fire or electric shock. 3. If you want to relocate the already installed product, be sure to turn off the power and then move or reinstall it. 4.
Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, or other apparatus (including amplifiers) that produce heat. 9.
Contents Introduction Features 6 Product & Accessories 7 Parts Name & Functions 8 Installation DIP Switch Setup 9 Installation using Mount Bracket 10 Cabling 13 Operation Check points before operation 15 Preset and Pattern Function Pre-Check 15 AUTO CALIBRATION 15 Starting OSD Menu 15 Reserved Preset 15 16 16 Pattern 16 Scan 16 Schedule 17 Other Functions 17 OSD Display of Main Screen 18 General Rules of Key Operation for Menu 18 How to use OSD Menu Main Menu 19 System In
Introduction FEATURES ❖ Camera Specifications • CCD Sensor : EX-view HADTM CCD • Zoom Magnification : × 36 Optical Zoom, × 12 Digital Zoom (Max × 432 Zoom) • Wide Dynamic Range Function • Day & Night Function : ICR(IR Cut filter Removal) • Various Focus Mode : Auto Focus / Manual Focus / Semi-Auto Focus. • Independent or Global camera settings for each Preset locations. ❖ Powerful Pan/Tilt Functions • Max.
Introduction PRODUCT & ACCESSORIES ❖ Product Wall Mount Type Ceiling Mount Type ENG ❖ Accessories Hexagonal wrench Anchor bolts (4pcs) Water proof tape Hole Template User’s Guide Safety Cable Housing Safety Cable Hanger English – 7
Introduction PARTS NAME & FUNCTIONS SUN SHIELD & UPPER HOUSING PTZ MECHANISM DOME SAFETY CABLE FAN & HEATER CABLE INNER BOX FAN HEATER HOUSING SAFETY CABLE HANGER DOME COVER • Dome Cover Do not detach protection vinyl from dome cover before finishing all installation process to protect dome cover from scratches or dust. In the dome cover, there are Fan and Heater to remove moisture on the bubble dome.
Installation ❖ Communication Protocol Setup DIP SWITCH SETUP Before you install the camera, you should set the DIP switches to configure the camera ID, communication protocol. ON ON 1 w WWWGaGhGw WWXGaGwTk WWYGaGwTw WWZGaGzhtz|un 2 3 4 5 6 7 8 iGy • Select the appropriate Protocol with DIP switch combination.
Installation ❖ RS-485 Termination Resistor ON ③ After locating the wall mount bracket on the anchor bolts properly. Tighten the nuts for anchor bolts ON 1 2 3 4 5 6 7 8 • Pin 8 is used for ON/OFF of RS-485 Termination. Normally, it must be OFF state. Especially when you have trouble with long Daisy chain style connection, turn ON this termination switch of last camera.
Installation ⑤ After hooking the safety cable on the hole of pipe [1], attach the upper housing to wall mount bracket by turning it at least seven turns [2]. To fix the upper body orientation, turn the handle of double nuts to clockwise tightly [3]. ⑦ Plug the connector of cable from junction box into properly. After checking the orientation of one touch connector in the upper housing, press the PTZ mechanism into hook in the upper housing. ENG ⑥ Open the dome cover to install the PTZ camera mechanism.
Installation ⑨ Close the dome cover. Care must be taken to locate dome cover by matching the “Arrow” mark. ٻ ٻ ٻ ٻ ٻ ٻ ⑩ Tighten four screws on the dome cover in sequence as shown in the picture bellow. ٻ ٻ 4 ٻ 1 ٻ ٻ ٻ 2 3 To maintain the best sealing, the torque of each screw must be in the range between 0.5 ~ 1.0 N·m (0.37 ~ 0.73 lbf·ft).
Installation CABLING Connector to the dome camera ALARM OUTPUT DVR/ Keyboard 1 RS-485 2 3 4 ALARM INPUT D+ D- D D+ D1 2 3 4 G 5 6 7 8 POWER NC. BNC VIDEO ENG Monitor ❖ Power Connection • Please, check the voltage and current capacity of rated power carefully. Rated Power Input Voltage Range Current Consumption AC 24V AC 19V ~29V 2.5 A ❖ RS-485 Communication • For PTZ control, connect this line to keyboard and DVR.
Installation ❖ Video Connection • Alarm Output • Connect with BNC coaxial cable. ❖ Alarm Input Connection • Sensor Input IN 1 INTERNAL IN 2 IN 3 IN 4 GND IN 5 IN 6 IN 7 IN 8 a It is noted that short circuit between GND and Input pin means alarm activation. If you want to use Alarm Input, the types of sensor must be selected in OSD menu. The sensor types are Normal Open and Normal Close If sensor type is not selected properly, the alarm can be activated reversely.
Operation CHECK POINTS BEFORE OPERATION • Before power is applied, please check the cables carefully. • The camera ID of the controller must be identical to that of the camera to be controlled. The camera ID can be checked in the System Information of OSD Menu. • If your controller supports multi-protocols, the protocol must be changed to match to that of the camera.
Operation PRESET • Function Max. 127 positions can be stored as Preset position. The Preset number can be assigned from 1 to 128, but 95 is reserved for starting OSD menu. Camera characteristics (i.e. White Balance, Auto Exposure) can be set up independently for each preset and they are adjusted by using OSD menu. Four relay outputs can be reacted in conjunction with one Preset. • Set Preset [1~128] • Run Preset [1~128] • Delete Preset To delete Preset, use OSD menu.
Operation SCAN OTHER FUNCTIONS • Function • Preset Lock The Scan function allows running sequence of Presets, Pattern and/or Auto Pans. Max 8 Scan can be stored. Each Scan can have max 20 action entities which can be preset, pattern or Auto Pan. Preset speed can be set up and the repeat number of Pattern & Auto Pan can be set up in Scan setup. Dwell time between actions can be set up also. Dwell Time Preset 1 Pattern 1 Scan 1 Max 20 Entities • Set Scan Use OSD Menu to create a Scan.
Operation be set up independently for each preset. There are 2 modes, “General” mode & “Special” mode. The General mode means that WB or AE can be set up totally and simultaneously for all presets in “ZOOM CAMERA SETUP” menu. The Special mode means that WB or AE can be set up independently or separately for each preset in each preset setup menu. Each Special WB/AE value should activate correspondingly when camera arrives at each preset location. During jog operation, General WB/AE value should be applied.
How to use OSD Menu MAIN MENU ROOT MENU EXIT • System Information Shows info and current configuration. • Display Setup • Baud rate Shows current Baud rate of PTZ control. • Address Shows current Camera ID for PTZ control.
How to use OSD Menu • Display [ON/OFF] MOTION SETUP Sets if camera makes mask shows or not on images. • Clear Mask [CANCEL/OK] MOTION SETUP Deletes data in the selected mask NO. PRESET LOCK OFF PWR UP ACTION ON AUTO FLIP ON JOG MAX SPEED 140/SEC JOG DIRECTION INVERSE FRZ IN PRESET OFF ❖ Privacy Zone Area Setup EDIT MASK 1 BACK EXIT Setup the general functions of Pan/Tilt motions.
How to use OSD Menu ❖ Parking Action Setup FUNCTION SETUP PARKING ACTION SETUP PARK ENABLE WATT TIME PARK ACTION OFF 00:10:00 HOME BACK EXIT BACK EXIT If Park Enable is set to ON, camera runs assigned function automatically if there is no PTZ command during assigned “Wait Time”. • Park Enable [ON/OFF] • Wait Time [5 sec ~ 4 hour] The time is displayed with “hh:mm:ss” format and you can change this by 1 sec unit.
How to use OSD Menu ❖ Edit Preset Scene PRESET SETUP EDIT SCENE - PRESET 1 PRESET SETUP PRESET NO. 1
How to use OSD Menu Back Space Char. Space Char. When Auto Pan function runs, camera moves from the preset assigned as the 1st point to the preset assigned as the 2nd point in CW(Clockwise) direction. Then camera moves from the preset assigned as the 2nd point to the preset assigned as the 1st point in CCW(Counterclockwise) direction.
How to use OSD Menu ❖ Edit Pattern ① By using Joystick, move to start position with appropriate zoom. To start pattern recording, press NEAR or ENTER key. To exit this menu, press FAR key. SCAN SETUP SCAN SETUP SCAN NO. 1 UNDEFINED CANCEL CLEAR SCAN EDIT PATTERN 1 BACK EXIT • Scan Number MOVE TO START POSITION [NEAR:START/ FAR:CANCEL] 0/0/x1/N ② Move camera with joystick of controller or run preset function to memorize the path (mostly curve path) in a selected pattern.
How to use OSD Menu ③ Set up Action, Dwell time and Option. Note that selected item is displayed in reverse. Move cursor Left/Right to select items and move cursor Up/Down to change each value. EDIT SCAN 1 NO. ACTION NO. DWELL OPT 1 2 3 4 5 EDIT SCAN 1 NO. ACTION NO. DWELL OPT NONE NONE NONE NONE NONE SAVE CANCEL ⑤ After finishing setting up an Action, press NEAR or ENTER key to one-upper-level menu (Step ②).
How to use OSD Menu The meaning of each value: SCHEDULE SETUP DAY SCHEDULE SETUP MASTER ENABLE DAY TIME ACT 1 UNDEFINED 2 UNDEFINED 3 UNDEFINED 4 UNDEFINED 5 UNDEFINED 6 UNDEFINED 7 UNDEFINED BACK • Master Enable NO 24hour Format ACT PRS(Preset), AUP(Auto Pan), PTN(Pattern), SCN(Scan), HOM(Home) If you finish a rule, press NEAR or ENTER key to select another rule. Repeat this procedure to fill up the schedule in mind.
How to use OSD Menu CAMERA SETUP Setup the general functions of zoom camera module ZOOM CAMERA SETUP FOCUS MODE SEMIAUTO DIGITAL ZOOM ON IMAGE FLIP OFF FLICKERLESS OFF BACK EXIT • Focus Mode ❖ White Balance Setup WB SETUP - GLOBAL WB MODE zRED ADJUST zBLUE ADJUST BACK EXIT • WB Mode [AUTO/MANUAL/SEMIAUTO] [AUTO/MANUAL] In Manual mode, Red and Blue level can be set up manually Sets camera focus mode.
How to use OSD Menu • IRIS [Works when AE MODE is MANUAL or IRIS model] Range: CLOSE/F1.6/F2/F2.4/F2.8/F3.4/F4/F4.8/ F5.6/F6.8/F8/ F9.6/F11/F14/F16/F19/F22/F28. (18 steps) DATE/TIME SETUP DATE TIME 01/JAN/2008(TUE) 00:00:01(H/M/S) • GAIN [Works when AE MODE is MANUAL] Enhances image brightness automatically in case that luminance level of image signal is too low.
How to use OSD Menu EDIT PASSWORD [█ ] ---------1234567890 ABCDEFGHIJ KLMNOPQRST UVWXYZabcd efghijklmn opqrstuvwx yz<>-/:. ---------- OK CANCEL DISABLE * Set Home Position? When you replace the camera block or the orientation of camera is changed due to maintenance operations, it is very difficult to maintain same pan orientation. Therefore, all function data depending on pan orientation such as preset, pattern, scan, auto pan, and privacy zone mask are not useful any more accordingly.
How to use OSD Menu SYSTEM INITIALIZE • Motion Configuration Preset Lock SYSTEM INITIALIZE CLEAR ALL DATA CLR DISPLAY SET CLR CAMERA SET CLR MOTION SET CLR FUNCTION SET REBOOT CAMERA REBOOT SYSTEM NO NO NO NO NO NO NO BACK EXIT OFF Power Up Action ON Auto Flip ON Jog Max Speed 140°/sec Jog Direction NORMAL Freeze In Preset OFF Park Action OFF Alarm I/O Action OFF • Clear All Data Deletes all configuration data such as display, camera, motion setup and so on.
Specifications SPECIFICATIONS Item Broadcasting Type CCD Effective Pixels Horizontal Resolution S/N Ratio Zoom Focal length Camera Min. illumination Range Pan/Tilt Speed Pan/Tilt Preset Pattern Auto Pan Scan Other Functions Communication Protocol Privacy Zone Alarm Input Alarm Output OSD Power Input General Power Consumption Dimension illumination 50 IRE 30 IRE 15 IRE 50 IRE 30 IRE 15 IRE Sens-up No No No 64 times 64 times 64 times Color 1.40 Lux 0.84 Lux 0.42 Lux 0.0219 Lux 0.0131 Lux 0.
Specifications DIMENSION • Wall Mount Bracket • Ceiling Mount Bracket 32 – 36x SMART DOME CAMERA Unit (mm)
Correct Disposal of This Product (Waste Electrical & Electronic Equipment) (Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature,indicates that it should not be disposed with other household wastes at the end of its working life.
