SmartDome Camera User's Guide

ManualsBrandsSamsung ManualsSecurity CameraSCC-C7433(P)

User’s Guide

SCC-C7433(P)/C7435(P)

SmartDome Camera (Outdoor type)

ENG FRE SPA JAP

SCC-C7435-NA_Cover-01.indd 1 2008-05-20 오전 10:49:12

Summary of content (82 pages)

PAGE 1
SmartDome Camera (Outdoor type) User’s Guide FRE SPA JAP -C7435-NA_Cover-01.
PAGE 2
Safety Precautions CAUTION RISK OF ELECTRIC SHOCK. DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit. This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit.
PAGE 3
CAUTION 1. 2. 4. 5. 6. 7. 8. 9. -C7433_7435-Eng.indd 2 FCC Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1) This device may not cause harmful interference, and 2) This device must accept any interference received including interference that may cause undesired operation. Caution This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of FCC Rules.
PAGE 4
Important Safety Instructions 1. 2. 3. 4. 5. 6. 7. Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, or other apparatus (including amplifiers) that produce heat. 9.
PAGE 5
Contents About this guide.............................................................................7 Product overview............................................................................7 Main features..................................................................................7 Components....................................................................................7 CHECKING COMPONENTS IN THE PACKAGE........................7 NAMES OF EACH PART...........................................
PAGE 6
DIGITAL ZOOM.........................................................................41 DISPLAY ZOOM........................................................................42 DISPLAY P/T.............................................................................43 EXIT..........................................................................................43 Video set .......................................................................................44 IRIS.............................................
PAGE 7
ENG -C7433_7435-Eng.indd 6 AUTO SET................................................................................68 AUX OUT CONTROL................................................................68 Other set .......................................................................................69 PROPORTIONAL P/T...............................................................69 TURBO P/T...............................................................................69 AUTO CAL...........................
PAGE 8
Overview ❚ About this guide This user guide includes basic instructions for the product. It is recommended that all users read this guide before use. This guide is divided as follows:  “Overview” introduces the user guide and product related information.  “Installation” explains how to set and install the product.
PAGE 9
NAMES OF EACH PART Your camera has the following components: ENG 1. Cover Front 2. Cover Rear 3. Camera Body 4. Cover-dome 5. Alarm Output: N/O, COM, N/C, AO-2, AO-1, GND 6. Alarm Input (1~8): AI-8, AI-7, AI-6, AI-5,GND, AI-4, AI-3, AI-2, AI-1, GND 7. RS-485: TXD+, TXD-, RXD+, RXD8. Power Input: 24V, EARTH, 24V 9. Video Output -C7433_7435-Eng.
PAGE 10
Installation ❚ Before installation THINGS TO KEEP IN MIND DURING INSTALLATION AND USE • Do not disassemble the camera on your own. • Always be careful when handling the camera. Do not strike the camera by your fists or shake it. Please be careful not to be careless when storing and operating it. • Do not place or operate the camera in any wet environment such as rain or wet surfaces. •D o not clean the camera with rough sandpaper. Please always use a dry cloth when cleaning it.
PAGE 11
SETTING COMMUNICATION PROTOCOL Use number 1~4 PIN of SW901 to set communication Protocol.
PAGE 12
BAUD RATE SETTING Use PIN 5 and 6 of SW901. BAUD RATE PIN 5 PIN 6 4800 BPS ON ON 9600 BPS OFF ON 19200 BPS ON OFF 38400 BPS OFF OFF The factory default setting is set to 9600BPS. 11 -C7433_7435-Eng.
PAGE 13
SETTING RS-422A/RS-485 TERMINATION Controller Division TX+(DATA+) TX-(DATA-) RX+ n < 32 RX- RX+ CAM 1 RX- RX+ CAM 2 RX- RX- CAM n-1 ENG As it is shown in the structure map, when Controller and RS-422A/RS-485 is connected, it should be terminated according to the Cable feature of impedance on the each end of the transmitting line to transfer the signals in long distance by controlling the reflection of the signals to the lowest.
PAGE 14
n < 32 Controller Division SW1-ON SW2-ON Division CAM 1 CAM 2 CAM n-1 CAM n Note A communication error may occur if you connect multiple cameras that are assigned the same address in the network. 13 -C7433_7435-Eng.
PAGE 15
Preparing the cable to connect to the SMARTDOME See the wiring diagram of the Holder Housing and prepare cables for the SMARTDOME. (Power adaptor: 24V AC, 3.0A) ENG -C7433_7435-Eng.
PAGE 16
HOLDER HOUSING 15 -C7433_7435-Eng.
PAGE 17
❚ Note: Connector arrangement of the camera adaptor board 3 4 5 1 14 13 12 11 ENG -C7433_7435-Eng.
PAGE 18
❚ Cable connection 1. First, connect one end of the BNC video cable connector to the Video Output Terminal (VIDEO OUT). 2. Then, connect the other end of the connector to the Video Input Terminal of the monitor. IN OUT Video terminal on the rear of monitor BNC Cable 17 -C7433_7435-Eng.
PAGE 19
3. Connect the Power Adapter to the Power Cable of the camera. 4. Adjust the switch on the Power Adapter to the proper voltage. Then, connect the Power Adapter's plug to the Power Connector. (Power adaptor: 24V AC, 3.0A) ENG Power Selection Switch under the Power Adaptor Power Selection Switch under the Power Adaptor -C7433_7435-Eng.
PAGE 20
5. Connect the Remote Control Terminal of the camera and the external Controller. 59% 59% 39% 39% Adapter Cable Controller 19 -C7433_7435-Eng.
PAGE 21
❚ Separately sold products for installation Depending on the installation site, it may be convenient to use one of the following products. 1. WALL MOUNT ADAPTOR (SADT-103WM) This adaptor is used for installing the SMARTDOME(SCC-C7433(P)/�� C7435(P)�� ) camera on an outdoor wall. ENG -C7433_7435-Eng.
PAGE 22
2. CEILING MOUNT ADAPTOR (SADT-100CM) This adaptor is used for installing the SMARTDOME(SCC-C7433(P)/�� C7435(P)�� ) for the SmartDome camera to a concrete ceiling. 3. POLE MOUNT ADAPTOR (SADT-100PM) This adaptor is used for installing the WALL MOUNT ADAPTOR (SADT-103WM) to a pole that is over 8 cm (2.76 in.) in diameter. 21 -C7433_7435-Eng.
PAGE 23
4. CORNER MOUNT ADAPTOR (SADT-110CM) This adaptor is used for installing the WALL MOUNT ADAPTOR (SADT-103WM) to the edge of wall. ENG -C7433_7435-Eng.
PAGE 24
❚ Installation precautions 1. Make sure that the installation site can sufficiently support a minimum of four times the net weight of the SCC-�� C7433�� (P)/�� C7435�� (P) SmartDome camera and other accessories. 2. Keep persons away from the installation area, as there is a risk of falling objects.
PAGE 25
2. Prepare the Holder Housing part. Refer to the wiring diagram below to connect the external cables and the cables of the Holder Housing. A. Remove one of the connectors connected to the cable end of the Holder Housing. B. Peel off the coating of the cable and connect it to the external cable using soldering/ (See page 17 in the installation guide to Connect the cables.) C. Use an insulation tape to wrap up the soldering portion of two cables. D. Connect the Connector to the Holder Housing again. E.
PAGE 26
3. Push the connected cables into the inside of the Rod Coupling. At the same time, insert the Holder Housing into the Rod Coupling while fitting the Guide of the Holder Housing into the Guide Hole of the Rod Coupling. Then, turn the Holder Housing clockwise by approximately 18 degrees. Finally, secure the Holder Housing to the Rod Coupling using the 3 Screws (M4xL8, fitting). - Install the Holder Housing so that the FRONT label faces the front of the camera to be installed.
PAGE 27
4. Hook up the Safety Wire Ring at the end of the Safety Wire on the Housing to the Safe Wire Rack of the Holder Housing. Note During installation or detachment, to avoid safety accident and ‘HOUSING’ damage due to the fall, make sure the safety tis secured to the ‘HOLDER HOUSING’. ENG -C7433_7435-Eng.
PAGE 28
5. Align the SAMSUNG logo on the Housing and the FRONT label of the Holder Housing so that they face the same direction, and insert the 3 Guides of the Housing into the Guide Hole of the Holder Housing. Turn the Housing counter clockwise by approximately 20 degrees. Finally, fasten the 3 screws (M4xL10). - Make sure not to let the Gasket loose from the Housing. (If the Gasket is loose, the product is not properly waterproof.
PAGE 29
6. Couple the Cover Front with the Cover Rear. In th next step, align the Arrow mark on the Cover Rear to face the START label on the Housing. Install these two parts into the Housing while aligning the Guide Hole of these parts with the Guide of the Holder Housing. Finally, turn these two parts so that the arrow mark on the Cover Rear is aligned with the LOCK label of the Housing. Tighten up the screw (M4xL8, fitting) as shown in the figure.
PAGE 30
※ Follow the steps below to fasten the SMARTDOME (SCC-C7433(P)/�� C7435(P)�� ) with the Wall Mount Adaptor (SADT-103WM). A. Refer to the Installation Guide of the Wall Mount Adaptor (SADT-103WM) to secure the Holder Housing to the Wall Mount Adaptor as shown in PIC 1. B. Then, repeat Step 4 to Step 6 of this Installation Guide until the assembly is completed as shown in PIC 2. WALL MOUNT ADAPTOR HOLDER HOUSING < PIC 1 > < PIC 2 > 29 -C7433_7435-Eng.
PAGE 31
Camera Setup CAMERA SET ... OFF/ON... V-SYNC INT/LINE.. DAY/NIGHT DAY.../NIGHT.../AUTO... MOTION DET OFF/ON... ZOOM SPEED 1/2/3/4 DIGITAL ZOOM OFF/X2~X16 DISPLAY ZOOM OFF/ON DISPLAY P/T OFF/ON EXIT QUIT/SAVE/PRESET IRIS ALC.../MANU.../WDR...* SHUTTER OFF/AUTO X2 ~ AUTO X256/1/100(1/120) ~ 1/10K AGC OFF/LOW/HIGH MOTION S.SLOW/SLOW/NORM/FAST/ F.FAST WHITE BAL ATW1/ATW2/AWC/MANU FOCUS MODE ONEAF/AF/MF SPECIAL DNR OFF/ON FLICKERLESS OFF/ON REVERSE OFF/H/V/H/V ENG VIDEO SET.
PAGE 32
PRESET PRESET MAP 0~127 ZONE SET... PRIVACY ZONE OFF/ON... ZONE DIR SET OFF/ON... ZONE AREA SET OFF/ON... EXIT QUIT/SAVE AUTO PAN 1/2/3/4 PATTERN 1/2/3 SCAN 1/2/3/4 AUTO PLAY OFF AUTO SET... 1... AUTO RETURN OFF/1MIN~12HOUR AUTO PLAY PRESET/SCAN/AUTO PAN/PATTERN PLAY NUMBER 1/2/3/4 2... ALARM SET... ALARM PRIORITY SET... ALARM IN SET... SET TIME ALARM1~8 1~8 EXIT QUIT/SAVE ALARM1~8 NO/NC/OFF EXIT ALARM OUT SET... AUTO SET...
PAGE 33
AUX OUT CONTROL... OTHER SET... OUT1 OFF/ON OUT2 OFF/ON OUT3 OFF/ON EXIT QUIT/SAVE OFF/ON TURBO P/T OFF/ON AUTO CAL. OFF/6HOUR/12HOUR/ 18HOUR/24HOUR D-FLIP OFF/ON CAM RESET ... ENG PROPORTIONAL P/T LANGUAGE* CLOCK SET... PASSWORD OFF/ON RS-485 ... EXIT QUIT/SAVE DISPLAY OFF/ON TIME FORMAT 12HOUR/24HOUR SET TIME DATE FORMAT MM/DD/YYYY DD/MM/YYYY YYYY/MM/DD SET DATE EXIT QUIT/SAVE SYSTEM INFO... Note *Selectable languages may vary depending on sales region.
PAGE 34
Note - If the power is turned off after PRESET, AUTO PAN, SCAN, PATTERN function is activated and no other control is made, camera will do the same function after the power is turned on. - When tilt position is over 90° and menu-on command is received, pan will automatically rotate 180° and tilt will be move to the corresponding position. Use the controller to press the MENU selection key and the following screen will be displayed. ** MAIN MENU ** CAMERA SET... VIDEO SET... PRESET... ZONE SET...
PAGE 35
❚ Camera setup CAMERA ID This CAMERA ID menu is used to assign a camera ID to this camera. If you press the Setup switch when the CAMERA ID menu is selected, the corresponding setup screen appears. (CAMERA SET) ON... INT DAY... OFF 4 OFF OFF OFF QUIT (CAMERA ID) ABCDEFGHIJKLMNOPQRSTUVWXYZ 0123456789 : ! - + * () / ENG CAMERA ID V-SYNC DAY/NIGHT MOTION DET ZOOM SPEED DIGITAL ZOOM DISPLAY ZOOM DISPLAY P/T EXIT RET SP ▶▶ ◀◀ SP LOCATION... CAMERA-1...........
PAGE 36
(CAMERA SET) CAMERA ID V-SYNC DAY/NIGHT MOTION DET ZOOM SPEED DIGITAL ZOOM DISPLAY ZOOM DISPLAY P/T EXIT (LL-PHASE) OFF LINE... DAY... OFF 4 OFF OFF OFF QUIT PHASE ( -262) I - - - - RET Select LINE and press Enter. You will see the LINE LOCK submenu where you can adjust the phase of the LINE LOCK. You can use the PHASE menu of the LINE LOCK submenu to assign as much PHASE as you want. DAY/NIGHT The DAY/NIGHT menu is used to configure the day and night related settings for this camera.
PAGE 37
DAY... If you press the ENTER when the DAY… submenu is selected, the corresponding screen appears. You can set the values for [C-GAIN] when the DAY… submenu is selected. You can set the values for [AGC COLOR] and [AGC DETAIL] while the AGC menu is selected. (DAY) ENG C-GAIN AGC COLOR AGC DETAIL RET (7) ------- I ( 0) ---- I---(0) I------- Note When the value of AGC DETAIL becomes large, it also makes the noise stand out. NIGHT...
PAGE 38
(BW) BURST RET (COLOR) OFF WHITE BAL RET ATW2 Even in night mode, you can see color images in bright illumination. Therefore you can select any of [COLOR…] and [BW…]. In case of [COLOR…], you have to set the color temperature for white balance. You can also specify the settings for red and blue colors on your own. In case of [BW...], the burst signals are output with the BW Composite Video signals when the BURST is set to [ON]. And no burst signals are output when the BURST is set to [OFF].
PAGE 39
(AUTO) LEVEL DAY  NIGHT NIGHT  DAY RET ( 0) I-----2S 5S ENG For this function, you can specify the level for each conversion between Day and Night. Note When the DAY/NIGHT is set to [AUTO...], the AGC is displayed with “---“ so you cannot change its setting. MOTION DET The MOTION DET menu is used to configure the motion detection related settings. If you press the ENTER when [ON…] is selected in the MOTION DET menu, the corresponding screen appears.
PAGE 40
Those 3 types are like the following: 1. Window Type The selected area is displayed with a box. The motion can be detected for the area only. You can manually set the motion detection area. You can use the UP/DOWN/LEFT/RIGHT Setup switch to set the size. To move to POSITION, press the switch. After setting the position using the UP/DOWN/ LEFT/RIGHT Setup switch, press the Setup switch to move to the upper menu. To set the size and position for AREA, select any of 0, 1, 2, and 3.
PAGE 41
3. B lock Type The screen displays with small blocks. When a motion is detected in the selected blocks, the small blocks are displayed on the screen. [PRESET] : The whole screen becomes the motion detection area. [USER...] : You can manually set the motion detection area. Use the UP/DOWN/LEFT/RIGHT, ENTER to set the area. To erase the selected block, press the ENTER. ENG To select [RET], press UP key on the top block or press DOWN key on the bottom block and then press ENTER key to return a upper menu.
PAGE 42
ZOOM SPEED In the ZOOM SPEED, menu you can select the speed of the ZOOM Key (Tele/Wide). (CAMERA SET) CAMERA ID V-SYNC DAY/NIGHT MOTION DET ZOOM SPEED DIGITAL ZOOM DISPLAY ZOOM DISPLAY P/T EXIT OFF INT DAY... OFF 4 OFF OFF OFF QUIT Use the Left/Right key in the ZOOM SPEED menu to select the speed. 1: Slowest speed 2: Low speed 3: High speed 4: Fastest speed DIGITAL ZOOM You may set up the digital zoom magnification ratio in the DIGITAL ZOOM menu. The magnification ratio ranges from OFF to 16.
PAGE 43
(CAMERA SET) CAMERA ID V-SYNC DAY/NIGHT MOTION DET ZOOM SPEED DIGITAL ZOOM DISPLAY ZOOM DISPLAY P/T EXIT (CAMERA SET) OFF INT DAY... OFF 4 OFF OFF OFF QUIT CAMERA ID V-SYNC DAY/NIGHT MOTION DET ZOOM SPEED DIGITAL ZOOM DISPLAY ZOOM DISPLAY P/T EXIT OFF INT DAY... OFF 4 X16 OFF OFF QUIT ENG DISPLAY ZOOM In DISPLAY ZOOM, you can display the ZOOM scale on the screen. (CAMERA SET) CAMERA ID V-SYNC DAY/NIGHT MOTION DET ZOOM SPEED DIGITAL ZOOM DISPLAY ZOOM DISPLAY P/T EXIT X032 OFF INT DAY...
PAGE 44
DISPLAY P/T In DISPLAY P/T, you can display the position of Pan/Tilt on the screen. (CAMERA SET) CAMERA ID V-SYNC DAY/NIGHT MOTION DET ZOOM SPEED DIGITAL ZOOM DISPLAY ZOOM DISPLAY P/T EXIT 270/090 OFF INT DAY... OFF 4 OFF ON ON QUIT Note - If no change on the Pan/Tilt position is made for 3 seconds, the information window will disappear. - It allows an error range of ± 2˚. EXIT The EXIT menu is used to return to the MAIN menu. - QUIT : Ignores the changed information and restores the saved information.
PAGE 45
❚ Video set IRIS There is a function to automatically adjust IRIS to the incoming light level. Owing to this function, you may set up the brightness level yourself. The ALC(Auto Light Control) menu allows you for video output level setup. The WDR(Wide Dynamic Range) menu allows you for setting up the level of WDR. Note ENG SCC-C7433(P) does not support for WDR function. ALC Choose the ALC of the IRIS item and press the ENTER and set the submenu to the Video Output level and BLC will be shown.
PAGE 46
(ALC) BLC LEVEL RET BOTTOM... ( 0) ---- I---- For items in the BLC menu, the user can set the area and location of the BLC area by pressing ENTER key after put the cursor on [USER…] using the Left, Right key. For AREA items, you can use the Up, Down, Left, Right key to designate the AREA, and then press the ENTER key. You can set the location for areas using the Up, Down, Left, Right key in the [LOCATION]. (ALC) BLC LEVEL RET (BLC) USER... ( 0) ---- I---- ...
PAGE 47
(BLC) (BLC) ... RET ... RET ENG Use Left, Right key in the LEVEL menu to control the video output level (brightness). MANU When you press the ENTER key after selecting MANU in the IRIS item, an additional screen appears in which you can set manually opening or closing the IRIS. (VIDEO SET) (MANUAL) IRIS SHUTTER AGC WHITE BAL FOCUS MODE SPECIAL MANU... OFF HIGH ATW2 ONEAF ... EXIT QUIT -C7433_7435-Eng.
PAGE 48
WDR The WDR camera is a state-of-art technology to expand the screen profit, mostly effective when you photograph both indoor and outdoor. In short, this function provides you with the distinct reproduction of not only the indoor but also the outdoor. Press the ENTER to set up the WDR level. (VIDEO SET) (WDR) IRIS SHUTTER AGC WHITE BAL FOCUS MODE SPECIAL WDR... OFF HIGH ATW2 ONEAF ...
PAGE 49
(VIDEO SET) IRIS SHUTTER AGC WHITE BAL FOCUS MODE SPECIAL ALC... OFF HIGH ATW2 ONEAF ... EXIT QUIT ENG Keep pressing both Left and Right in the SHUTTER menu, the speed will change in the following sequence. OFF → AUTO X2 → AUTO X4 → AUTO X6 → AUTO X8 → AUTO X12 → AUTOX16 → AUTO X24 → AUTO X32 → AUTO X48 → AUTO X64 → AUTO X96 → AUTO X128 → AUTO X256 → OFF → 1/100(1/120) → 1/250 → 1/500 → 1/1000 → 1/2000 → 1/4000 → 1/10K ※ In case the IRIS mode is set to WDR, only the following modes are available.
PAGE 50
(VIDEO SET) IRIS SHUTTER AGC WHITE BAL FOCUS MODE SPECIAL ALC... OFF HIGH ATW2 ONEAF ... EXIT QUIT Note When the COLOR/BW menu of the camera set is set to [AUTO...], AGC will be displayed as “---“. You can’t adjust the settings manually. MOTION The MOTION function is available only when the SHUTTER menu is set to Slow Shutter AUTO, being composed of 5 steps, [S.SLOW], [SLOW], [NORM], [FAST], [F.FAST]. - [S.
PAGE 51
WHITE BAL Lights are generally denoted as color temperatures and expressed in Kelvin (K) units. The general light color temperatures are shown below.
PAGE 52
- MANU : If WHITE BAL menu is set to MANU mode, the user can set the white Balance considering the current illumination. Select MANU menu and press the ENTER, the sub screen where you can select Manual White Balance will be shown. Use the left/right keys to select 3200K, 5600K or OFF(USER) mode in the PRESET menu. - 3200K : Set color temperature to 3200K - 5600K : Set color temperature to 5600K - USER : Choose out a proper value from the RED and BLUE graph for color and temperature setup.
PAGE 53
(VIDEO SET) IRIS SHUTTER AGC WHITE BAL FOCUS MODE SPECIAL ALC... OFF HIGH ATW2 AF ... EXIT QUIT ENG Note ※ AF function may not possible with types of objects listed below. For such objects, focus manually.
PAGE 54
DNR DNR(Digital Noise Reduction) function enables the picture to be reduced noise. (SPECIAL) DNR FLICKERLESS REVERSE DETAIL Y-LEVEL C-LEVEL POSI/NEGA RET ON OFF OFF (2) -- I(0) I-------(0) I-------+ FLICKERLESS When this is set to [ON], the shutter speed is set to 1/100 sec (for NTSC) or 1/120 sec (for PAL) to prevent from flickering by the discordance between vertical synchronization frequency and on-and-off frequency of the light.
PAGE 55
C-LEVEL It is used to set the levels for the Burst signal and the entire color signal of the video signal. POSI/NEGA It is used to output as it is, or mirror the video brightness signal. EXIT -C7433_7435-Eng.indd 54 ENG The EXIT menu is used to return to the MAIN menu. - QUIT : Ignores the changed information and restores the saved information. - SAVE : Saves the information of the setting condition of the menu.
PAGE 56
❚ Preset This is the menu that user sets the PAN/TILT location, Zoom/Focus, and screen condition, so the camera can monitor the presetting area on demand. A total of 128 presets are available. ** MAIN MENU ** CAMERA SET... VIDEO SET... PRESET... ZONE SET... AUTO SET... ALARM SET... OTHER SET... CLOCK SET... SYSTEM INFO... (PRESET MAP) 0 5 10 15 20 25 30 1 6 11 16 21 26 31 ID: PRESET 0 PRESET NO.
PAGE 57
POSITION SET From “POSITION SET...” press the ENTER key to get into the PAN/TILT, FOCUS/ZOOM SET screen to set the PAN/TILT location and FOCUS/ZOOM condition then press the ENTER key to return to a upper menu. PRESET ID This is the ID set up function for each PRESET. It can be set up to 12 characters using the left, right, up, and down keys. The ID location can be set in the submenu of “LOCATION...” ENG VIDEO SET This is the screen setting function for each PRESET.
PAGE 58
❚ Zone set ■ The ZONE SET menu includes the setup of PRIVACY ZONE, ZONE DIR SET, and ZONE AREA SET. ** MAIN MENU ** (ZONE SET) CAMERA SET... VIDEO SET... PRESET... ZONE SET... AUTO SET... ALARM SET... OTHER SET... CLOCK SET... SYSTEM INFO... PRIVACY ZONE ZONE DIR SET ZONE AREA SET ON... OFF OFF EXIT QUIT PRIVACY ZONE Move PAN/TILT/ZOOM to select an area that can infringe someone privacy, then this function will hide the area if it can be involved in the photograph to protect his privacy.
PAGE 59
Note ※ For the safer privacy protection, select about 10 % more than the actual area to hide when you set up the PRIVACY ZONE area. ※ The mosaic of the recorded images is set to be the PRIVACY ZONE. The mosaic of the recorded images can not be recovered after recording. ZONE DIR SET -C7433_7435-Eng.indd 58 (ZONE SET) PRIVACY ZONE ZONE DIR SET ZONE AREA SET ENG Press the ENTER key in the “ZONE DIR SET ON…” mode to enter the SET NORTH screen MAP.
PAGE 60
ZONE AREA SET Press the ENTER key to enter the ZONE AREA MAP screen from “ZONE AREA SET...”. Select a ZONE AREA number from the ZONE AREA MAP screen and press the ENTER key to enter the ZONE AREA setup screen. (ZONE SET) (ZONE AREA MAP) PRIVACY ZONE ZONE DIR SET ZONE AREA SET OFF OFF ON... EXIT QUIT 0 1 2 3 4 5 6 7 RET ZONE AREA SET0 LOCATION ZONE ID SET ZONE ENABLE ... ... ON EXIT QUIT 59 -C7433_7435-Eng.
PAGE 61
LOCATION The [LOCATION...] menu designates the left/right LIMIT positions of ZONE AREA. Enter the setup screen to move PAN, then select a start position and press the ENTER key. Move PAN again to select an end position and press the ENTER key. Now, ZONE AREA setup is complete. LOCATION ZONE ID SET ZONE ENABLE ... ... ON EXIT QUIT ENG -C7433_7435-Eng.
PAGE 62
ZONE ID SET This function is used to allocate as many as 12 IDs to each zone area. Use Left/Right/ UP/DOWN for this purpose. You may select the ID position from the additional menu of [LOCATION...]. ZONE AREA SET0 LOCATION ZONE ID SET ZONE ENABLE ... ... ON EXIT QUIT ZONE AREA ID 0 ABCDEFGHIJKLMNOPQRSTUVWXYZ 0123456789 : ! - + * () / RET SP▶▶ ◀◀SP LOCATION... ZONE. 0...... ZONE ENABLE This function turns [ON] or [OFF] the ZONE AREA ID indication. 61 -C7433_7435-Eng.
PAGE 63
❚ Auto set The AUTO SET menu includes AUTO PAN, PATTERN, and SCAN and it is able to set up the AUTO PLAY motion. AUTO PAN After selecting the locations of two points (PAN/TILT) of START and END, it loops continuously in the set up SPEED. The number of AUTO PAN is up to 4. (AUTO SET) CAMERA SET... VIDEO SET... PRESET... ZONE SET... AUTO SET... ALARM SET... OTHER SET... CLOCK SET... SYSTEM INFO... AUTO PAN PATTERN SCAN AUTO PLAY 1 2 1 2 1 2 OFF RET QUIT 3 3 3 ENG -C7433_7435-Eng.
PAGE 64
POSITION SET The menu [POSITION SET …] sets the Start / End position of AUTO PAN. Return to the settings screen and set the desired START position for PAN/TILT, and then press the ENTER key. And, set the END position for the PAN/TILT. Press the ENTER key to finish the setup for AUTO PAN Start/End positions.
PAGE 65
PATTERN This is a replay function so that the MANUAL functions such as PAN, TILT, ZOOM, and FOCUS are played for 2 minutes. Note - When the PATTERN is saved/executed, the PAN/TILT is operated with PROPORTIONAL ON, TURBO OFF. - I f the SSC-1000 or SSC-2000 is used when uploading/downloading the menu setup, reset the PATTERN because it may be different with the first setting. ENG -C7433_7435-Eng.
PAGE 66
PATTERN can be set up to 3. Choose 1, 2, or 3 with the Left/Right key in the [PATTERN SET] and press the ENTER key to get into the PATTERN set up screen. From the moment “PATTERN SET 1” is gone for 2 minutes, it memorizes the MANUAL movements and after 2 minutes, it will return to a upper menu. If you want to finish set up before the 2-minutes ends, press the ENTER key. SCAN SCAN sets the direction of PRESET movement during SCAN operation. The number of SCAN is up to 4.
PAGE 67
AUTO PLAY If you press the ENTER switch when the [1…] submenu is selected, the corresponding screen appears. (AUTO PLAY SET) (AUTO SET) 1 2 1 2 1 2 1... RET QUIT 3 3 3 4 4 AUTO RETURN AUTO PLAY PLAY NUMBER OFF PRESET 0 EXIT QUIT ENG AUTO PAN PATTERN SCAN AUTO PLAY AUTO RETURN This menu sets up the time during which AUTO PLAY repeats. AUTO PLAY This function sets up the motion which will be repeatedly performed by the camera whenever the time set by AUTO RETURN elapses.
PAGE 68
If you press the ENTER switch when the [2…] submenu is selected, the corresponding screen appears. (AUTO SET) AUTO PAN PATTERN SCAN AUTO PLAY 1 2 1 2 1 2 2... RET QUIT 3 3 3 4 4 (SET TIME) ID START END 1 00:00 03:00 2 03:00 06:00 3 06:00 09:00 4 09:00 12:00 5 12:00 15:00 6 15:00 18:00 7 18:00 21:00 8 21:00 24:00 EXIT PLAY NO. OFF OFF OFF OFF OFF OFF OFF OFF QUIT Set the start/end time and select PRESET, PATTERN, AUTO PAN or SCAN to set up.
PAGE 69
ALARM PRIORITY SET This sets the priority of the 8 ALARM inputs so ALARM can work corresponding to the priority. The priority of the DEFAULT is ALARM1, ALARM2, ALARM3, ALARM4, ALARM5, ALARM6, ALARM7, ALARM8. If the ALARM is working at the same time and the priority is the same, it will operate according to the DEFAULT priority. While the ALARM is working, it cannot detect MOTION.
PAGE 70
❚ Other set ** MAIN MENU ** (OTHER SET) CAMERA SET... VIDEO SET... PRESET... ZONE SET... AUTO SET... ALARM SET... OTHER SET... CLOCK SET... SYSTEM INFO... PROPORTIONAL P/T TURBO P/T AUTO CAL. D-FLIP CAM RESET LANGUAGE PASSWORD RS-485 EXIT ON OFF OFF OFF ... ENGLISH OFF ... QUIT PROPORTIONAL P/T This function controls the PAN/TILT speed to the ZOOM magnification ratio during the manual operation of PAN/TILT.
PAGE 71
D-FLIP When D-FLIP is off, TILT movement ranges from 0° to 90°. When D-FLIP is on, TILT movement ranges from 0° to 180°. When D-FLIP is on, images mirror vertically and horizontally in the area beyond TILT 90°. CAM RESET ENG CAM RESET clears all the settings made so far and restores the factory default settings. [CAMERA RESET?] message appears when you select CAM RESET. Select [CANCEL] to return to the menu setup display or select OK to restore the factory default settings.
PAGE 72
PASSWORD This function selects or cancels the MENU setup password. Press the ENTER key at the state of PASSWORD ON, and the following screen will appear for password setup. (OTHER SET) PROPORTIONAL P/T TURBO P/T AUTO CAL. D-FLIP CAM RESET LANGUAGE PASSWORD RS-485 EXIT (PASSWORD) OFF OFF OFF OFF ... ENGLISH ON... ... QUIT 0 1 2 3 4 5 6 7 8 9 **** RET **** Press Up/Down/Left/Right key to locate the cursor on a number and press the ENTER key for password setup.
PAGE 73
RS-485 (OTHER SET) (RS-485) OFF OFF OFF OFF ... ENGLISH ON... ... QUIT PRIORITY PROTOCOL BAUD RATE ADDRESS RET HW SAMSUNG HALF 9600 0 ENG PROPORTIONAL P/T TURBO P/T AUTO CAL. D-FLIP CAM RESET LANGUAGE PASSWORD RS-485 EXIT [PRIORITY] menu is used to set the priority between hardware and software. If you select [HW], it operates according to the value of the camera hold adapter. If you select [SW], you can manually set [PROTOCOL], [BAUD RATE], [ADDRESS] for RS-485.
PAGE 74
❚ System info This menu allows you to check S/W version, communication protocol, baud rate, and address of the camera. ** MAIN MENU ** CAMERA SET... VIDEO SET... PRESET... ZONE SET... AUTO SET... ALARM SET... OTHER SET... CLOCK SET... SYSTEM INFO... (SYSTEM INFO) ALARM VER. MOTOR VER. CAMERA VER. EEPROM VER. PROTOCOL COMM. TYPE BAUD RATE ADDRESS SERIAL NO. RET 1.000 1.000 1.000 1.000 SAMSUNG RS-485, HALF 9600 0 000000000000000 * ALARM, MOTOR, CAMERA and EEPROM VER. may change without notice.
PAGE 75
❚ Shortcut keys SSC-1000 or SSC-2000 Controller supports the following short keys.
PAGE 76
Function Key AUTO RETURN *1) [PRESET] + [1] + [4] + [8] + [Enter] AUTO Calibration [PRESET] + [1] + [4] + [9] + [Enter] CAM RESET [PRESET] + [1] + [5] + [0] + [Enter] Other keys than AUTO CAL. and AUTO RETURN, upon execution, shall be applied to the MENU setup process. *1) The use of AUTO RETURN will be available only when the function equivalent to AUTO PLAY, a sub menu of AUTO SET has been built in. 75 -C7433_7435-Eng.
PAGE 77
422 12 318 ENG -C7433_7435-Eng.
PAGE 78
Product Specifications Item Product Type Power Input Heater Power Consumption Broadcasting Type Details Zoom lens single body WDR SmartDome CAMERA SCC-C7433/C7435 : AC 24V ± 10% (60Hz ± 0.3Hz) SCC-C7433P/C7435P : AC 24V ± 10% (50Hz ± 0.
PAGE 79
Item Details WDR SCC-C7433 : N/A SCC-C7435 : x128 SCC-C7435P : x160 Signal Output COMPOSITE VIDEO OUT : 1.0 Vp-p 75 ohms/BNC Lens PAN Function SCC-C7433(P) Color B/W 2.0 0.20 1.2 0.12 0.6 0.06 0.008 0.0008 0.005 0.0005 0.002 0.0002 SCC-C7435(P) Color B/W 1.2 0.12 0.7 0.07 0.3 0.03 0.005 0.0005 0.003 0.0003 0.001 0.0001 One body; 32x Zoom lens Focal length : 3.55 to 113 mm Aperture : F1.69(Wide), F4.17(Tele) PAN range : 360° Endless Preset Pan Speed : 400° /sec, maximum - Manual Pan Speed : 0.
PAGE 80
Item Details Operation Temperature -49°F ~ +122°F Operation Humidity ~90% SIZE DOME : 168(ø), Outline : 258(ø) x 422(H) Weight NET : 5.95 Kg Lives of Main Parts Slip-ring: Rotated 10,000,000 times 79 -C7433_7435-Eng.
PAGE 81
Memo _SCC-C7435-JAP.indd.
PAGE 82
_SCC-C7435-JAP.indd.