SCC-C6455N Smart Dome Camera User Manual imagine the possibilities Thanks you for purchasing this Samsung product. To receive a more complete service, please visit our website www.samsungsecurity.com 00885A-NA_SCC-C6455N-ENG.
overview CAUTION RISK OF ELECTRIC SHOCK. DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit. This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit.
6. Do not place conductive objects (e.g. screwdrivers, coins, metal parts, etc.) or containers filled with water on top of the camera. Doing so may cause personal injury due to fire, electric shock, or falling objects. 8. If any unusual smells or smoke come from the unit, stop using the product. In such case, immediately disconnect the power source and contact the service center. Continued use in such a condition may cause fire or electric shock. English 7.
overview CAUTION 1. Do not drop objects on the product or apply strong blows to it. Keep away from a location subject to excessive vibration or magnetic interference. 2. Do not install in a location subject to high temperature (over 50°C), low temperature (below -10°F), or high humidity. Doing so may cause fire or electric shock. 3. If you want to relocate the already installed product, be sure to turn off the power and then move or reinstall it. 4.
FCC Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions : 2) This device must accept any interference received including interference that may cause undesired operation. English 1) This device may not cause harmful interference, and Caution This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of FCC Rules.
overview important safety instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, or other apparatus (including amplifiers) that produce heat. 9.
contents overview Important Safety Instructions Contents Features What’s Included At a Glance installation & connection 10 10 14 17 Preparing Installation Installation Initial Setup Connecting With Other Device setup 20 21 22 24 33 34 35 37 41 42 44 44 46 46 47 How to use the Keyboard Controller Main Menu Profile Camera Set Intelligent Video Privacy Zone Preset Auto Set Zone Set Alarm Set Clock Set Other Set Communication System Info Language 48 49 51 Shortcut Keys Specifications Product Appearance
overview Features With the state-of-the-art digital signal processing technology, full digital image processing and special algorithm of 600-line high resolution implemented High performance surveillance camera, equipped with x43 zoom lens and digital zoom IC, enabling monitoring up to 688 times WDR to cover the full screen irregardless of its brightness DAY/NIGHT to improve the sensitivity by automatic conversion into the black and white mode at night or in the environment with low illumination W
At a Glance CAMERA English HOOK HOOK LENS FRAME SET RS-485 ALARM IN POWER INPUT ALARM OUT M Wipe out a dirty surface of the lens softly with a lens tissue or cloth to which you have applied ethanol. 00885A-NA_SCC-C6455N-ENG.
installation & connection Preparing Installation Use the ceiling installation template when you install the camera on the ceiling on your own. Run the cables through the “” shaped hole on the center of the template, and remove films on the adhesives, and then attach the template on the desired location on the ceiling. When installing the frames set, align all template’s screw holes and those of the frames set. This template prevents dust entering from the ceiling into the camera assembly.
2. Use the three “SCREWS” to fix the “FRAME SET” on a “CAMERA” installation position. English FRAME SET SCREW SCREW ADAPTOR SCREW 3. Connect external cables to the “CONNECTORS(ALARM IN, POWER, RS-485, ALARM OUT)”and connect the “CONNECTOR” to the “ADAPTOR”. Insert the cable into the “FRAME SET”, and close the “ADAPTOR”.
installation & connection 4. Connect the “SAFETY WIRE” of the “CAMERA” to the “BRACKET WIRE” on the “FRAME SET”. Arrange the “22P CONNECTOR” of the “CAMERA” in line with that of the “ADAPTOR”, push the “HOOK” on either end of the “CAMERA” in the “RACK” direction of the “FRAME SET” to secure the two. Then, ensure that all of the two “HOOKS” “clicks” to fix to the “RACK” properly.
5. Arrange the “COVER” arrow in line with the “FRAME SET” arrow, and push in the “COVER”. Insert the “COVER” to the end, and turn the “COVER” clockwise. As shown in the figure below, turn it until you see the “BUTTON” hole and hear a click. English Ensure that the “COVER” should not move any further if you turn the “COVER” counter clockwise. BUTTON FRAME SET COVER CAMERA COVER If you want to remove the “COVER”, hold down the “BUTTON” and turn the “COVER” counter clockwise to remove the “COVER”.
installation & connection INITIAL SETUP Camera Address Setup Use SW606, SW605, and SW604 to specify the camera address. You can specify between 0 and 255 for the address, where the hundreds digit is with SW606, the tens digit with SW605, and the ones digit with SW604. ex) Camera address: If the address is 1, follow the steps in the figure below. SW606 (x100) SW605 (x10) SW604 (x1) Communication Protocol Setup Use pins #1~#4 of SW603 to specify the communication protocol.
Baud Rate Setup Use pins #5, #6 of SW603 to set the baud rate. English BAUD RATE PIN 5 PIN 6 4800 BPS ON ON 9600 BPS OFF ON 19200 BPS ON OFF 38400 BPS OFF OFF The factory default is 9600 BPS.
installation & connection n < 32 Termination SW1-ON SW2-ON Controller Termination CAM 1 CAM 2 CAM n-1 CAM n M A communication error may occur if you connect multiple cameras that are assigned the same address in the network. 16_ installation & connection 00885A-NA_SCC-C6455N-ENG.
Connecting WITH OTHER device English MONITOR CONTROLLER/DVR ALARM IN POWER SOURCE ALARM OUT Connecting to a monitor 1. Connect one end of the BNC video cable connector to the Video Output Terminal (VIDEO OUT). 2. Connect the other end of the connector to the Video Input Terminal of the monitor. 00885A-NA_SCC-C6455N-ENG.
installation & connection To connect ALARM IN 1. Connect one end of the external device's signal line to a corresponding ALARM IN port of the monitor. 2. Connect the other end of the signal line to the earth-grounding [GND] port. To connect ALARM OUT 1. Connect one end of the external device's signal line to a corresponding ALARM OUT port of the monitor. 2. Connect the other end of the signal line to the common [COM] port.
Connecting the adaptor cable Adaptor Board English Power Supply Connect the cables as necessary, and turn on the camera to check if it works properly. 1. Connect the adaptor to the power terminal of the camera. 2. Plug the power cord of the adaptor into the wall outlet. 00885A-NA_SCC-C6455N-ENG.
setup Connect the camera to the keyboard controller or DVR, with which you can manipulate and change the settings of the camera. How to use the keyboard controller Follow the steps below to set the camera menu using the controller. 1. Open the Camera Setup screen. 2. Use the joystick to navigate through the menus. 3. Press [ENTER] to select a menu item. 4. Use the joystick to change the value of the selected item. 5. Press [ENTER] to apply your changes.
Main Menu This is the first screen you ever see when you turn on the camera where you can set the camera environment to your needs. PROFILE MAIN MENU Select a mode appropriate to the camera PROFILE installation environment. CAMERA SET INTELLIGENCE CAMERA SET PRIVACY ZONE PRESET You can configure the camera settings. AUTO SET INTELLIGENCE ZONE SET ALARM SET Offers motion detection and tracking CLOCK SET functions. OTHER SET PRIVACY ZONE You can configure the privacy settings.
setup PROFILE You can select one from the pre-determined configurations as appropriate to your specific camera installation environment. Your selection on each item in PROFILE will affect all other settings of the camera. STANDARD PROFILE Automatically optimizes the camera settings STANDARD to the normal environment. ITS ITS BACKLIGHT DAY/NIGHT This setting enables you to analyze the traffic GAMING situation and take the traffic information at a CUSTOM glance.
CAMERA SETUP MENU ITS BACKLIGHT DAY/NIGHT GAMING MOTION (F.FAST) --- (F.FAST) --- NORM (F.
setup CAMERA SET You can configure the general settings of the camera module. For selecting and saving each menu item, refer to “How to use the keyboard controller”. (page 20) 1. Select - . The Camera Setup menu appears. 2. Change the settings as necessary, or select an item to check. CAMERA SET CAMERA ID VPS IRIS MOTION DNR SHUTTER SENS-UP FLICKERLESS XDR OFF OFF ALC (F.
IRIS The IRIS menu is useful if you set to adjust the intensity of radiation incoming to the camera. [ 00] ----I---- BACKLIGHT AREA BLC USER English ALC : Adjust the open and close of the iris. - LEVEL : Select an overall brightness level. - BLC : With set to , you can specify the BLC area. With AREA set to , you can specify the position and size.
setup AGC With this, you can adjust the AGC level of a CAMERA SET camera. CAMERA ID OFF With AGC active, if the signal strength falls VPS OFF below the standard level, AGC will amplify the IRIS ALC AGC (VERY HIGH) --video signal to automatically improve the DNR MID sensitivity. SHUTTER OFF If is set to , or SENS-UP OFF mode, the menu will switch to FLICKERLESS OFF XDR MID . With the USER ( ) submenu selected, press [ENTER] to display the corresponding screen.
SHUTTER As long as SENSE UP is set to AUTO, FIXED / FLICKERLESS to ON / BACKLIGHT to WDR, the SHUTTER menu is not available. CAMERA SET CAMERA ID OFF VPS OFF IRIS ALC AGC (VERY HIGH) --DNR MID SHUTTER 1/100 SENS-UP (OFF) --FLICKERLESS (OFF) --XDR MID English You can select a fixed fast electronic shutter speed in 7 options ranging from 1/100 to 1/10k, which is mostly used to take a picture of a fast moving object.
setup DAY/NIGHT You can specify a recording mode according to the scene. For selecting and saving each menu item, refer to “How to use the keyboard controller”. (page 20) 1. Select - . 2. Select a screen transition mode according DAY/NIGHT AUTO WHITE BAL to the illumination, and set options as FOCUS MODE ONEAF appropriate. ZOOM SPEED [2] DAY : Fixed to DAY mode, regardless of DISPLAY ZOOM OFF the scene.
You can specify MASK 1 and 2 simultaneously. If is set to , the MASK AREA function is not available. M English EXT : The interface to an external alarm enables an automatic switch between DAY and NIGHT mode. If you set to EXT, and alarm #1 to NO/NC in ALARM SETALARM IN SET, the alarm can be used for an input signal in EXT mode of . If an alarm signal occurs, the mode will switch to NIGHT.
setup 1. Select - . 2. Select a mode where you set the . DAY : You can set the RED, and BLUE value in DAY mode. The screen will be displayed in colors DAY/NIGHT according to your settings. MODE You can set the R-GAIN, and B-GAIN value only in mode. If AGC is set to or , the NIGHT WHITE BAL DAY AWC [ 00] ---- I ---[ 00] ---- I ---- RED BLUE R-GAIN B-GAIN [0064] [0064] menu can not be accessed.
FOCUS MODE You can select a focus mode according to the angle that you adjusted for camera recording. - ONEAF : Restores focus after the operation of pan/tile/zoom, and operates the same as in unless the operation of pan/tile/ zoom is executed. DAY/NIGHT WHITE BAL FOCUS MODE ZOOM SPEED DISPLAY ZOOM DISPLAY P/T DIGITAL ZOOM DETAIL V-SYNC AUTO [2] ONEAF [2] OFF OFF X16 English - AF : This will monitor the screen continuously to focus automatically.
setup V-SYNC You can set the V-SYNC mode. - If you select , the camera will use the internal synchronization. - If selecting , the camera will use an external power frequency for synchronization. The LL-PHASE can be adjusted as appropriate. AGC COLOR SUP You can adjust the color reproduction range according to AGC. REVERSE AGC COLOR SUP REVERSE POSI/NEGA PIP DIS MID OFF + OFF OFF You can reverse the video signal from left to right, upside down, or vice versa to your convenience.
Intelligent Video You can enable the motion detection and tracking functions. 1. Select -. 2. Select each item and set appropriately. MOTION You can enable the motion detection and tracking functions. M INTELLIGENCE MOTION ADVANCED MASK AREA DISPLAY SENSITIVITY RESOLUTION ALARM OUT 1 2 [4] 3 OFF OFF 4 ON English For selecting and saving each menu item, refer to “How to use the keyboard controller”.
setup DISPLAY When selected , it displays the motion detected and detection of configured advanced function. SENSITIVITY Sets the sensitivity of motion sensor. RESOLUTION The bigger the resolution setting, the smaller the object that can be detected. ALARM OUT When selected , it outputs alarm signal when the motion is detected and on a detection of configured advanced function.
4. Select the . Select the pixel level for the SIZE and LOCATION settings. [4] English 5. Select the and press [ENTER]. Using the joystick, set the size of the privacy zone. PRIVACY ZONE SET 1 PIXEL LEVEL 6. Select the and press [ENTER]. Using the joystick, set the position of the privacy zone. 7. Save the changes and move to the previous screen and select the
