Thank you for buying a Samsung SYSTEM CONTROLLER. This manual will guide you through using the SYSTEM CONTROLLER. Please read this manual carefully before using the SYSTEM CONTROLLER.
Contents ●Important Safety Instructions 3 ●Major Functions and Features (5-1) TOUR Setup 19 (5-2) TOUR Operation 19 (1) Overview 5 (6) MODEL 21 (2) Features 5 (7) TRACE 22 ●Product Components 5 ●System Overview 6 (7-1) TRACE Memory 22 (7-2) TRACE Operation 23 (8) AF ●Names and Functions of Each Part 23 (1) Camera Setup Section 7 (9) OSD 24 (2) Number Pad 8 ●DVR Mode 25 (3) External Device Selectors 8 ●Controller Mode (4) Universal Controller 9 (1) Controller Setup Mode
Important Safety Instructions Warning ■ All work related to the installation of this appliance must be performed by qualified service personnel or system installers. - If the product is connected or installed improperly, electric shock, fire, severe injury, and/or damage can result. ■ Please install the product on a completely flat floor. - Always check the strength and stability of the installation location. - Do not drop the appliance on the floor. This may result in damage or injury.
Important Safety Instructions Maintenance and Repair ■ If the controller body gets dirty, turn the power off and wipe the surface with a soft cloth. - Do not use chemical agents such as alcohol or benzene. ■ For detailed information on upgrading the firmware, please direct your inquiries to the installation vendor. Refer all work related to the installation of this appliance to qualified service personnel or system installers.
Major Functions and Features (1) Overview This product is designed for use only with the Speed Dome camera, CCTV receiver, and Samsung Digital Video Recorder. ● Speed Dome camera : Samsung Techwin (SPD-1600/2200/2500), PELCO-D, PANASONIC (WV-CS854A), SAMSUNG ELECTRONICS (SCC-643-641) ● CCTV Receiver : SRX-100B ● DVR : Samsung Techwin (SVR-1630/1620/430) (2) Features - It is possible to totally control the 255 Speed Dome camera, CCTV Receiver and Samsung Digital Video Recorder.
System Overview ※ Please refer to page 39 for the detailed connection map of the JUNCTION Box, Controllers and external devices. (1) General Connection Dome Camera DVR Dome Camera + DVR: 255 max. Junction Box CCD Camera Remarks : Controller Connection Cable : RS-485/422 : Video Cable Dome Camera SVR-1630: 255 max.
Names and Functions of Each Part (1) Camera Setup Section ① RESET : Resets camera power. ② PRESET : Moves camera to the preset location (see p.16). ③ LIGHT : Toggles the lights around the camera on and off. ④ AUX : Toggles the camera’s external case AUX on and off. ⑤ TOUR : Sets more than 1 group for tour and performs continuous group action (see p.19). ⑥ SALVO : Not used; will be applied to F/W in the future.
Names and Functions of Each Part (2) Number Pad ※ 'F' in the table below refers to the Function button. ① 0 ~ 9 : Used for entering camera ID, channel number, monitor number, DVR ID, etc. (see p.23). ② F + 0 : Activates the system setup menu (see p.24). ③ ▲ / ▼ : Used for increasing or decreasing menu values in detailed setup menus. ※ When using functions that are performed by a combination of the function button and numeric keys, the setup may be different depending on the camera manufacturer.
Names and Functions of Each Part (4) Universal Controller ① ZOOM W/T : Performs camera zoom action (wide and telephoto). ② FOCUS -/+ : Used for manual focus adjustment. ③ || : Used for moving the menu cursor up (when menu is active), pausing DVR playback, or playing stills. ④ ■ : Used for moving the menu cursor down (when menu is active) or stopping DVR playback. ⑤ I▶ : Used for moving the menu cursor left (when menu is active) or Slow Playback.
Names and Functions of Each Part ※ Some DVR controller buttons may not be supported or may be used differently than as described in this manual, depending on the DVR model. Please refer to the table below for the buttons supported by major DVR model manufacturers. The DVR button with multiple functions works in the same way on the controller.
Names and Functions of Each Part (6) Camera Controller ① Joystick: Used for moving the camera up, down, left, and right, and for zoom control (see p.13). 1) Tilt up (Up button): Moves the camera up. 2) Tilt down (Down button): Moves the camera down. 3) Tilt left (Left button): Moves the camera left. 4) Tilt right (Right button): Moves the camera right. 5) Turn stick clockwise: Performs telephoto-zoom. 6) Turn stick counter-clockwise: Performs wide zoom.
Before Operation (1) Power-On ① Power on the connected external devices before turning the controller on. ② Press the power button at the back of the controller to power on the controller. ③ The [SYSTEM Controller] message and F/W version will be displayed in the LCD monitor, and the message will disappear when the controller is ready for use. ▤ The [JOYSTICK ERROR] error will be displayed in the LCD monitor if the joystick is not placed in the center during power-on.
Before Operation (4) Joystick/Camera Control Button ■ The joystick can be used to control the camera’s left and right (pan) and up and down (tilt) movements. ■ The joystick can be used to control camera zoom functions.
Before Operation (5) Camera Movement Speed Control ■ Use the joystick or press the Slow/Fast button at the bottom of the camera control button section to adjust the camera movement speed. ▤ You must press the ESC button after adjusting the camera movement speed in order to be able to use other controller buttons. [SLOW/FAST button] ▤ The SLOW/FAST button can be used to adjust movement speed for models without a joystick.
PTZ Mode (1) PTZ Setup Mode ■ This menu is for setting up the PTZ camera function. It is impossible to operate Speed Dome and DVR by sub-controllers when the master controller is set to on. ① At the initial screen, press the Function button and press the 0 button to activate the [SETUP SYSTEM] menu. ② Press the 1 button to activate the [PTZ SETUP 1 ▶] menu.
PTZ Mode (2) PRESET ■ This menu is for setting the camera to move to preset locations. (2-1) PRESET Setup ① At the [PTZ SETUP 1 ▶] menu, press the 1 button (see p.15). ② Use the joystick or camera control button (SCC-3000 model) to move the camera to the desired location (move up, down, left, and right, and control zoom). ③ Enter a preset number.
PTZ Mode (3) SWING ■ This menu is for setting the camera to alternate between two assigned locations horizontally (pan) or vertically (tilt). Setting the SWING SETUP menu by controllers is only possible in the SPD series. In case of products by other manufacturers, the setting has to be done by the OSD menu of the camera. See the camera manual for more information. (3-1) SWING Setup ① At the [PTZ SETUP 1 ▶] menu, press the 2 button (see p.15).
PTZ Mode (4) GROUP ■ This menu is for setting repeated sequential surveillance of assigned locations with assigned speed and intervals. Setting the GROUP SETUP menu by controllers is only available for an SPD series. In case of products by other manufacturers, the setting has to be done by the OSD menu of the camera. See the camera manual for more information. (4-1) GROUP Setup ① At the [PTZ SETUP 1 ▶] menu, press the 3 button (see p.15). ② Enter a Group number.
PTZ Mode (5) TOUR ■ This menu is for setting one or more Groups for Tour so that continuous Group operations can be carried out. The TOUR SETUP menu is only available for an SPD series. (5-1) TOUR Setup ① At the [PTZ SETUP 1▶] menu, press the 4 button (see p.15). ② Press a Group number to add to the Tour. ▤ Up to 6 Groups can be added. TOUR SETUP 1 GROUP NUM? <1-6> Enter:Tour Set ③ Press the ENTER button to finish the setup. (5-2) TOUR Operation ① At the initial screen, press the Tour button.
PTZ Mode TOUR GROUP 1 《20》 GROUP 3
PTZ Mode (6) MODEL ■ This menu is for setting the PTZ camera ID and camera type. ① At the [PTZ SETUP 1▶] menu, press the ▶▶ button (see p.15). ② Press the 1 button to move to the Model Setup screen. PTZ SETUP 2 1:MODEL 2:TRACE 3:AF Press Numeric Key ③ Press a number in the number pad to set the PTZ camera ID. The camera model type saved in EEPROM is displayed on the LCD monitor when changing camera ID.
PTZ Mode (7) TRACE ■ This menu is for inputting camera movements, through joystick or camera control buttons, into the memory for a certain period of time, to allow repeating of stored movements when performing the Trace (PATTERN) function. Setting the TRACE SETUP menu by controller is only available for an SPD series. In case of products by other manufacturers, the setting has to be done by the OSD menu of the camera. See the camera manual for more information.
PTZ Mode (8) AF (Auto-Focus) ■ This menu is for adjusting camera focus manually or automatically after camera operation. If AF is set to OFF in the camera setup menu, set the AF of the controller to ON and then automatic adjustment is performed after camera operation. ① At the [PTZ SETUP 1▶] menu, press the ▶▶ button (see p.15). ② Press the 3 button to move to the AF Setup screen. ③ Press the 1 button to automatically adjust the focus after camera operation.
PTZ Mode (9) OSD ■ This is used for displaying the camera menu on the monitor. ① At the initial screen, press the OSD button. ② Use the controller buttons to set up the camera menu. - OSD : SPD 1600/2200/2500 - Toggle camera menu on/off (hold down for 2 seconds) PELCO-D - Toggle camera menu on/off (press ESC) PANASONIC (WV-CS854A) - Toggle camera menu on/off (press ESC) Samsung (SCC-643/641) - Toggle camera menu on/off (press ESC) - ESC : Cancels the menu selection. - ENTER : Selects the menu.
DVR Mode DVR MODEL Setup ■ This menu is for setting the DVR ID and model for operation by a controller. Sub-controllers cannot be used if the master controller is in Setup mode. ① At the initial screen, press the FUNCTION button and press the 0 button to activate the [SETUP SYSTEM] menu. ② Press the 2 button to activate the [DVR SETUP] menu. SETUP SYSTEM 1:PTZ 2:DVR 3:CONTROLLER Press Numeric Key DVR SETUP 1:DVR MODEL SETUP Press Numeric Key ③ Press the 1 button to activate the [DVR Model SETUP] menu.
Controller Mode (1) Controller Setup Mode ■ Sub-controllers cannot be operated if the master controller is in setup mode. ① At the initial screen, press the FUNCTION button and press the 0 button to activate the [SETUP SYSTEM] menu. ② Press the 3 button to activate the [Controller SETUP 1 ▶] menu. ③ Press the ▶▶ button to activate the [◀Controller SETUP 2 ▶] menu. ④ Press the ▶▶ button to activate the [▶ Controller SETUP 3] menu.
Controller Mode (2) Controller ID Setup ■ This menu is for setting controller ID. ① At the [Controller SETUP 1 ▶] menu, press the 1 button (see p.26). ② Press a number on the number pad to enter a controller ID. ③ Press the ENTER button to set the controller ID. ▤ Assign number 1 for setting the controller ID for the master controller. ▤ The lower the ID number, the higher the controller priority.
Controller Mode (4) DATA COPY ■ This menu is for copying master controller menu data to a sub-controller. The controller ID value is not copied. ① At the [Controller SETUP 1▶] menu, press the 3 button (see p.26). ② Press a number on the number pad to enter the ID number for the subcontroller where the data will be copied. CONTROLLER SETUP1 1:CONTROLLER ID 2:SERIAL 3:COPY Press Numeric Key DATA COPY SUB-CONTROL ID? [ 0 ] Enter:ID Set <2-16> ③ Press the ENTER button to set the controller ID.
Controller Mode (5) RESPONSE ■ If the camera RESPONSE is set to two-way reception (RESPONSE ON), the controller RESPONSE menu must be set to ON. If the camera RESPONSE is set to one-way reception (RESPONSE OFF), the controller RESPONSE menu must be set to OFF.If this is not followed, the system may have a configuration conflict.For more information on the camera RESPONSE settings, direct your inquiries to the installation vendor.
Controller Mode ▤ For information on camera RESPONSE settings (DIP switch settings), refer to the camera manual.
Controller Mode (6) PASSWORD ■ This menu is for setting the password to enter when changing controller setup values upon power-on. (6-1) PASSWORD Setup ① At the [Controller SETUP 1▶] menu, press the ▶▶ button (see p.26). ② Press the 2 button to activate the Password Setup screen. ③ Press the 1 button to activate the Password Setup screen. ④ Use the number pad to enter a 6-digit password. ⑤ The password verification screen will appear. Re-enter the same password. The password will be saved.
Controller Mode (6-2) Applying Password – Setup Mode ① At the Password Setup screen, press the 2 button. ② Press the 1 button to ask for a password every time the setup mode is selected. Press the 2 button to skip asking for a password. PASSWORD SETUP 1:PASSWORD SETUP 2:MENU ON 3:POWER ON Press Numeric Key PASSWORD SETUP 1:MENU PASSWORD ON 2:MENU PASSWORD OFF Press Numeric Key (6-3) Applying Password - Power ① At the Password Setup screen, press the 3 button.
Controller Mode (7) PRIORITY ■ This menu is for setting the connected sub-controller to use a PTZ camera or DVR within the specified restrictions. This menu is available for master controller (ID: 1) only. ① At the [Controller SETUP 1 ▶] menu, press the ▶▶ button twice (see p.26). ② Press the 1 button to activate the Priority Setup screen. ③ Press the 1 button to activate the PTZ Camera Restriction Setup menu. Press the 2 button to activate the DVR Restriction Setup menu.
Controller Mode (8) DEFAULT ■ This menu is for resetting the changed controller setup values to the default values. ① At the [Controller SETUP 1 ▶] menu, press the ▶▶ button twice (see p.26). ② Press the 2 button to open the Default Setup screen. ③ Press the 1 button to change the controller setup values to the default values and restart the controller. Press the 2 button to cancel the process.
REFERENCE (1) Swing, Group Movement Speed ▤ For Swing setup, the speed setup value can be 240˚/second for pan, and 180˚/second for tilt. Setup value Degrees / second Setup value Degrees / second Setup value Degrees / second Setup value Degrees / second 1 0.8 33 23 1 0.8 33 23 2 1.0 34 24 2 1.0 34 24 3 1.5 35 25 3 1.5 35 25 4 2.0 36 26 4 2.0 36 26 5 2.5 37 27 5 2.5 37 27 6 3.0 38 28 6 3.0 38 28 7 3.5 39 29 7 3.5 39 29 8 4.0 40 30 8 4.
REFERENCE (2) System Connections (2-1) Connecting Controller and Junction Box (2-2) Connecting Junction Box and External Devices [SUB JUNCTION BOX] JUNCTION BOX X X X X X X X X X X X RX+ RX- TX+ TX- X X X X X X X RX+ RX- X X X [SVR-430/900/1620 connection] * RX+ and TX+ / RX- and TX- must be short-circuited.
REFERENCE (3) RS-485/422 Pin Layout (D_SUB_FEMALE) Terminal Name 1 +12V 2 RX+ (RS-485+) PORT1 3 RX- (RS-485-) PORT1 4 TX- PORT1 5 TX+ PORT1 6 - 7 RX+ (RS-485 +) 5 1 15 11 1 5 6 9 PORT2 8 RX- (RS-485 -) PORT2 9 TX- PORT2 10 TX+ PORT2 11 GND 12 RX+ (RS-485 +) PORT3 13 RX- (RS-485 -) PORT3 14 TX- PORT3 15 TX+ PORT3 (4) RS-232C Pin Layout (D_SUB_MALE) Terminal Name 1 - 2 RX 3 TX 4 - 5 GND 6 - 7 - 8 - 9 - 《37》
REFERENCE (5) Controller Specifications MODEL SCC-3000 Power (Consumption) 12VDC(Max 700mA) Control DVR & Speed Dome (SPD-2500, 1600, 2200) PTZ Control SPD-2500, 1600, 2200 all function control Compatibility Remote Control - DVR : SVR-1620 / 900 / 430 / 1630 / 1650 - PTZ : SEC, PELCO-D, PANASONIC RS-485 / RS-422 Connector 3Port Baud Rate (bps) Max 38400bps (Sub-controller : 56400bps) LCD Display 20 x 4 Character LCD PTZ Control Joystick (3Axis Twist Zoom) Sub Keyboard Flow control connect
SALES NETWORK SAMSUNG TECHWIN CO., LTD. 145-3, Sangdaewon 1-Dong, Jungwon-Gu, Sungnam, Kyungki-Do, Korea 462-703 TEL: +82-31-740-8137~8141 FAX: +82-31-740-8145 SAMSUNG OPTO-ELECTRONICS AMERICA, INC. ELECTORONIC IMAGING DIV. SAMSUNG OPTO-ELECTRONICS UK LTD. 40 Seaview Drive, Secaucus NJ 07094, U.S.
