Thermal Night Vision Camera SCB-9050/9051 User Guide Before installing and operating this product, please read this manual thoroughly.
The lightning flash with an arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
Contents Features Features…………………………………………………………………………… 5 Warnings & Cautions… ……………………………………………………… 6 Warnings…………………………………………………………………………… 7 Cautions…………………………………………………………………………… 8 Overview…………………………………………………………………………… 9 • External Part Names…………………………………………………………… 10 • • • • • ■ Names of external camera parts…………………………………………………………… ■ Names of internal camera parts…………………………………………………………… ■ Assembly/Adjustment Methods…………………………………………………………… • Installing the Camera………………………………………………………… ■ Inputting Power
Warnings Warnings & Cautions The following points are presented in order to promote customer safety and prevent property damage. After reading this information, be sure to use the product in the correct manner. * Please direct any product inquiries towards the merchandiser from which the device was purchased. Be aware that if service is carried out, customers are responsible for any costs pertaining to the use of expensive ladders or other equipment.
Cautions Overview Position the camera so that it is not facing towards the sun or any other bright light source. Do not install the product in very hot or very cold locations. ❶ 2 4 3 1/4"-20 UNC (20 THREAD) L:4.5mm±0.2mm (ISO standard), or 0.197" (ASA standard) 5 Using the product in an area with very hot (55°C or higher) or cold (-30°C or lower) temperatures could result in product failure, or a reduction in image quality.
External Part Names Assembly/Adjustment Methods 104 Names of external camera parts 352 123 Ø104 ❶ 1 2 3 4 2 SCB-9050 V ideo signal/communications (RS485) cable Power cable (AC 24 V, 50/60 Hz) Lens (14 mm) Support platform for fastening camera 104 1 2 3 4 Ø104 367 Front 123 Names of internal camera parts Rear 2 ❶ 2 SCB-9051 ❶ A screw to fix the focus is located on the bottom of the lens.
Installing the Camera Inputting Power Calibration (NUC MODE) 1. Remove the lens cap. 2. Engage the power. (Use the adapter provided with this product.) 3. The rated input voltage for this product is AC 24 V, 50/60 Hz. • This device is not fitted with a power switch. The device must be provided with power to turn it • After checking the label on the cable on the right side of the camera, connect the output cable of the provided adapter.
Installing the Camera ■RS485 Communications Controls Using RS485 communications, function settings menus can be adjusted using the Samsung Techwin DVR or System controller. (1) Controlling menus using a PC Using an RS485 converter, connect the camera's RS485 control terminal to a serial cable. Example) PC serial board (COM1) → serial cable → RS485 converter → camera RS485 control terminal (2) Controlling menus using a DVR system controller 3.
Interface ■Rear Terminal Placement ■Connector specifications and signals ① ④ ② Function ③ ⑤ RS485 I/F (R+/-, D-/+) ① POWER LED • Power ON : Lit • Abnormality/Warning : Flashing ② Terminal Block A PIN 1 2 3 4 5 Name R+ RDD+ G 6 Video 7 8 9 G POW+ POW- Explanation RS485+ Communications Non-inverting input/output RS485- Communications Inverting input/output RS485- Communications Inverting input/output RS485+ Transmission Non-inverting input/output Ground Composite video signal
Operating the Camera Function Menu Configuration Function Main Menu Explanation BRIGHTNESS AUTO MANUAL AUTO / MANUAL (level ranging from 1-10) CONTRAST AUTO MANUAL AUTO / L/H RANGE NUC AUTO LOW NUC MODE INTERVAL IMAGE ADJ 3D-DNR SHARPNESS D-ZOOM POLARITY COLOR BRIGHTNESS AUTO / MANUAL (level ranging from 1-10) CONTRAST RANGE NUC NUC NUC MODE INTERVAL / AMB / MANUAL INTERVAL 0H 1MIN-24H 0MIN AMB 0.1°C-10.
Operating the Camera Function Settings Methods BRIGHTNESS Function settings may be adjusted using the internal switches after removing the rear cover. (Refer to “5. Interface” for directions on how to remove the rear cover.) UP button : Move the menu cursor up. RIGHT button : Increase (+) the settings value of the selected item. DOWN Key : Move the menu cursor down. LEFT button : Decrease (-) the settings value of the selected item.
Operating the Camera Press the LEFT button or RIGHT button while the cursor is aligned with “MANUAL” to adjust the CONTRAST over ten different levels: 1 ⇒ 2 ⇒ 3 ⇒ 4 ⇒ 5 ⇒ 6 ⇒ 7 ⇒ 8 ⇒ 9 ⇒ 10 ⇒1. Select “2. RETURN” to confirm the current setting and go back to the MAIN SETUP menu screen. (Default value: 6) * In order for the CONTRAST AUTO setting to be enabled, the BRIGHTNESS AUTO setting must already be turned on.
Operating the Camera 3D-DNR (Noise Reduction) : P ress the LEFT button or the RIGHT button to limit the amount of noise produced. (Default value: M) SHARPNESS (Edge Emphasis) : Use this option to use image processing to emphasize edges. Press the LEFT button or RIGHT button while the cursor is aligned with “2. SHARPNESS” to switch the SHARPNESS setting from 0-5. Select “5. RETURN” to confirm the current setting and go back to the MAIN SETUP menu screen.
Operating the Camera TV SYSTEM (Video Output Setting) : SPECLAL SETUP Use this option to adjust the video output setting. PAL ▶ 1.TV SYCTEM Press the LEFT button or RIGHT button while the cursor is 2.LANGUAGE ENGLISH aligned with “1. TV SYSTEM” to switch the TV SYSTEM 3.COMM ADJ 4.RESET setting from: NTSC ⇒ PAL ⇒ NTSC. Select “5. RETURN” 5.RETURN to confirm the current setting and go back to the MAIN SETUP menu screen.
Specifications Operating the Camera Notes • Do not disengage the power while settings are being saved. * Although the infrared sensor has been built using high-precision technology, please understand that there may be times when pixels may be lost, or remain stuck/flashing. Also, be aware that continuously monitoring a high temperature object beyond a certain period of time may produce an afterimage.
Troubleshooting Ø104 352 SCB-9050 104 • If nothing can be seen onscreen : - Verify that the power source is connected properly, and that the device is receiving power. - Verify that the video signal wire is connected properly. • If screen images do not appear clearly : - Wipe the lens with a clean cloth or brush to remove any dust that may be present. - Adjust the status of the monitor. - Change the position or angle of the camera if a large amount of bright light is displayed onscreen.
DECLARATION OF CONFORMITY Application of Council Directive(s) 2004 / 108 / EC Manufacturer's Name SAMSUNG TECHWIN CO., LTD Manufacturer's Address SAMSUNG TECHWIN CO., LTD MEMO 42, SUNGJU-DONG CHANGWON-CITY, KYUNGNAM, KOREA, 641-716 European Representative Name European Representative Address Equipment Type/Environment Thermal Night Vision Camera Model Name SCB-9050/9051 Beginning Serial NO. C5BY6V3Z300001X Year of Manufacture 2010.03.
MEMO Thermal Night Vision Camera 34 User Guide MEMO Thermal Night Vision Camera 35 User Guide
SALES NETWORK • AMSUNG TECHWIN CO., LTD. S 145-3, Sangdaewon 1-dong, Jungwon-gu, Seongnam-si Gyeonggi-do, Korea, 462-703 TEL : +82-31-740-8151~8 FAX : +82-31-740-8145 • AMSUNG TECHWIN AMERICA Inc. S 1480 Charles Willard St, Carson, CA 90746, UNITED STATES Tol Free : +1-877-213-1222 FAX : +1-310-632-2195 www.samsungcctvusa.com • AMSUNG TECHWIN EUROPE LTD.
