Low Light, High Resolution, Day & Night Camera User Manual SCB-1000
B T ■ ■ Low Light, High Resolution, Day & Night Camera User Manual Copyright ©2010 Samsung Techwin Co., Ltd. All rights reserved. Trademark is the registered logo of Samsung Techwin Co., Ltd. The name of this product is the registered trademark of Samsung Techwin Co., Ltd. Other trademarks mentioned in this manual are the registered trademark of their respective company. Restriction Samsung Techwin Co., Ltd shall reserve the copyright of this document.
Before operating the camera, confirm the camera model and correct input power voltage. To help you understand this manual thoroughly, we’ll introduce our model description.
safety information 6 CAUTION RISK OF ELECTRIC SHOCK. DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit.
e e 7. Do not install the unit in humid, dusty, or sooty locations. doing so may cause fire or electric shock. 8. If any unusual smells or smoke come from the unit, stop using the product. in such case, immediately disconnect the power source and contact the service center. continued use in such a condition may cause fire or electric shock. 9. If this product fails to operate normally, contact the nearest service center. never disassemble or modify this product in any way.
safety information im FCC STATEMENT 1 This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions : 2 1) This device may not cause harmful interference, and 2) This device must accept any interference received including interference that may cause undesired operation. CAUTION This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of FCC Rules.
o e t 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, or other apparatus (including amplifiers) that produce heat. 9. Do not defeat the safety purpose of the polarized or grounding-type plug.
contents i INTRODUCTION 9 CONNECTION 16 CAMERA OPERATION 18 TROUBLESHOOTING 9 10 11 13 Features What’s included Component names and functions Lens 16 16 Connecting to a monitor Connecting to power 18 18 Menu Settings F y y y y 28 Troubleshooting y 28 y SPECIFICATIONS 30 30 Specifications y y y 8_ contents
s introduction FEATURES y Electronic DAY & NIGHT This camera has a function that electronically selects the mode that is appropriate for daytime or night-time conditions. The COLOR mode operates in daytime conditions to provide optimum colors, and BW mode operates in night-time conditions to enhance the definition of the image. y Electronic IRIS The electronic IRIS function enables continuous automatic control of the shutter between 1/60(1/50)~1/120,000 seconds.
introduction C WHAT’S INCLUDED F Check if the following items are included in the product package.
COMPONENT NAMES AND FUNCTIONS FRONT VIEW ➊ SIDE VIEW ➋➌ ➍ ➍ ● INTRODUCTION ❶ CCD protection cap : Please cover the CCD SENSOR when not using it. ❷ C-Mount lens adaptor : Please attach the C-Mount lens here. ❸ CS-Mount lens adaptor : Please remove the C-MOUNT lens adaptor and then attach it. ❹ Back Focus clamp screw : Please loosen the clamp screw with a screwdriver before adjusting the Back Focal length.
introduction L REAR VIEW ➑ L le ➐ ⓫ ➒ ❿ * High Voltage Type (SCB-1000PH) ➐ Video output terminal : Sends video signal and connects to the video input terminal of the monitor. ➑ Auto iris lens selection switch : Please change the mode to DC or VIDEO depending on the type of auto iris lens being used. ➒ Setting button: • SETUP button : Displays the menu on the screen and uses enter sub menu. • Up&Down button : Used to move the cursor up or down in the menu screen.
Lenses are sold separately. Lenses such as an auto iris lens, CS-Mount lens and C-Mount lens can be used. Please keep the lens clean. Any foreign objects and fingermarks on the lens can cause inferior image quality in low light level conditions. WHEN USING AN AUTO IRIS LENS 1. Please peel off about 8mm of the outer skin of the auto iris lens cable. approx. 8mm f 2. Please peel off about 2mm of the outer skin of the insulated conductor inside the lens cable. approx. 2mm 3.
introduction 5. Please insert the connection plug that is connected to the auto iris lens cable into the auto lens connector, which is located on the side of the camera. 6. Please set the lens selection switch, located on the side of the camera, to DC or VIDEO depending on the type of auto iris lens which is being used. WHEN USING A C-MOUNT LENS Please take off the CCD protection cap and attach the C-Mount lens to the camera by screwing it in clockwise. C-mount adaptor WHEN USING A CS-MOUNT LENS 1.
2. Please attach the CS-Mount lens to the camera by screwing it in clockwise. CS-mount adaptor ● INTRODUCTION Please use the specified lens connection parts as shown in the picture below. The use of the wrong sized parts of the wrong size may cause damage to the inside of the camera or result in poor fitting. Use of a lens which is too heavy affects the balance of the camera and may cause a malfunction. Please use a lens that weighs less than 450g.
connection CONNECTING TO A MONITOR Please connect the video output terminal located on the back of the camera to the monitor. W C CCD Camera Monitor y The connection method varies depending on the type of monitor and accessories. Please refer to the user’s manual for each instrument. y Please turn off the power when connecting. CONNECTING TO POWER Each model has a different power input specification. Please check the model type and standard power requirement before connecting to power.
High Voltage Type (AC230V, 50Hz) Copper wire size (AWG) #24 (0.22mm2) #22 (0.33mm2) #20 (0.52mm2) #18 (0.83mm2) Resistance value( /m) 0.078 0.050 0.030 0.018 Voltage Drop (V/m) 0.028 0.018 0.011 0.006 y As shown in the table above, voltage decreases as the wire gets longer. Therefore use of an excessively long adaptor output line for connection to the camera may affect the performance of the camera.
camera operation MENU Setup Menu LENS (selection) ● MANUAL ● DC / VIDEO SHUTTER (condition and speed control) ● ESC ● MANUAL ● FLK WHITE BAL ● ATW ● AWC ● MANUAL BACKLIGHT (Backlight compensation) ● OFF ● HIGH ● LOW ● MIDDLE AGC (Auto Gain control) ● OFF ● HIGH ● LOW ● MIDDLE SSNR (Samsung super noise reduction) ● OFF ● HIGH ● LOW ● MIDDLE SENS-UP (Low illuminance) ● OFF ● AUTO SPECIAL ● IMAGE ADJ ● SYNC ● LANGUAGE ● CAMERA ID ● MOTION DET ● RESET ● COLOR ● PRIVACY ● RETURN EXI
SETUP Select any function you wish to operate by using the UP and DOWN buttons. DC Modes can be changed using the LEFT and RIGHT buttons. --ATW OFF MIDDLE LOW OFF ● CAMERA OPERATION 䯝 LENS SHUTTER WHITE BAL. BACKLIGHT AGC SSNR SENS-UP SPECIAL EXIT 2. Select a desired function using the Up and Down buttons. y Place the cursor over a desired item. 3. Set up a selected item by using the Left and Right buttons. 4. To finish the setting, select ‘EXIT’ and press the SET button.
camera operation SHUTTER (CONDITION AND SPEED CONTROL) Auto or manual control can be selected. 1. When the SETUP menu is on the screen, please position the arrow to point to ‘SHUTTER’ by using the DOWN button. 2. Please select the shutter mode by pressing the LEFT or RIGHT button. SETUP LENS 䯝 SHUTTER WHITE BAL. DC --ATW y FLK : Please select ‘FLK’ mode when flickering occurs on the screen, due to an imbalance between illumination and frequency.
is d. y ATW(Auto Tracking White Balance) : This mode can be used within the color temperature range 1,800°K ~ 10,500°K (Ex. fluorescent light, outdoor, sodium vapor lamp or inside tunnels) y AWC(Auto White Balance Control) : Please press the SETUP button while the camera is directed at a piece of white paper to obtain the optimum state under current illumination. If the environment including the light source is changed, you have to adjust the white balance again.
camera operation y HIGH/MIDDLE/LOW : You can adjust the sensitivity of Backlight Compensation. y OFF : BLC function doesn´t operate. BACKLIGHT ON BACKLIGHT OFF AGC (AUTO GAIN CONTROL) The higher gain level, the screen gets brighter and the level of noise also increases. The BRIGHTNESS can be adjusted within the range of 1~70. 1. Please position the arrow to point to ‘AGC’ on the SETUP menu by using the UP and DOWN buttons. 2. Select a desired mode using the Up and Down buttons.
The background noise in the low light level decreases automatically as the level of gain changes. 1. Please position the arrow to point to ‘SSNR’ on the SETUP menu by using the UP and DOWN buttons. 2. Please select the mode you wish to operate by pressing the LEFT or RIGHT button. y OFF : There is no reduction in noise level. y LOW : There is a small reduction in noise level with almost no ghost image. SETUP LENS SHUTTER WHITE BAL.
camera operation The maximum storage magnification in low light level can be adjusted by pressing the SETUP button in ‘AUTO’ mode.(X2~X128) As the magnification increases, the screen gets brighter; moving object gets more afterimage. If storage magnification is increased while SENS UP is operating, it may cause noise, and spots may appear; however this is normal. SPECIAL 1. Please position the arrow to point to ‘SPECIAL’ on the SETUP menu by using the UP and DOWN buttons. 2.
g e SHARPNESS Level IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII 8 Press SET to Return - Please press the SETUP button. - The available range of level is 0 ~ 31. y CAMERA ID : 1) Please position the arrow to point to ‘CAMERA ID’ by using the UP or DOWN button. 2) Please select ‘ON’ by pressing the LEFT or RIGHT button. If ‘OFF’ is selected, the ID does not appear on the monitor even if it has been input. 3) Please press the SETUP button. 4) Up to 15 letters can be used for the ID.
camera operation 5) When a name has been chosen, please select a position for the name display. FRONT DOOR ➊ Please move the cursor onto ‘POS’ and then press the SETUP button. ➋ The name will appear at the top left hand corner. ➌ Please find the position you wish to display the name by using the 4 directional buttons, and then press the SETUP button. 6) Please select ‘END’ and then press the SETUP button to complete ID input.
MOTION DETECT - OFF : MOTION DETECTION mode is ▶ AREA SEL AREA1 AREA STATE ON cancelled. IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII 15 TOP - ON : Any motion in the selected areas IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII 30 DOWN is observed. IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII 20 LEFT 2) Please select the area you wish to observe IIIIIIIIIIIIIIIIIIIIIIIIIIIIIIII 40 RIGHT from the 4 areas in AREA SEL mode. Press SET to Return 3) Please select ON mode for the chosen area.
troubleshooting TROUBLESHOOTING If there are problems in operation, please refer to the items below. If the problem persists, please contact the agent you purchased this product from. Problems Troubleshooting Nothing appears on the screen. y Please check the power connection. y Please check the video signal line connection. y Please check and make sure that the auto lens switch is set to DC (VIDEO) when using a DC (VIDEO) lens. y Please check the Brightness of Auto Iris lens.
Problems Troubleshooting y Please check if the camera is facing directly into sunlight or fluorescent light. y Please check if an auto iris lens is being used. y Please check the connection of the lens connector cable. L/L mode isn’t able to be selected. y Have you connected your camera to DC power source? Connect it to AC power source. L/L mode is not available. y Please check the frequency of power supply (60Hz for NTSC, 50Hz for PAL). COLOR (DAY & NIGHT) mode is not working.
specifications SPECIFICATIONS Item SCB-1000NA SCB-1000ND SCB-1000PA SCB-1000PD SCB-1000PH G Imaging Device 1/3” Super HAD CCD Total Pixels 811(H) x 508(V) 795(H) x 596(V) Effective Pixels 768(H) x 494(V) 752(H) x 582(V) W E S Scanning System 2:1 Interlace Internal / Line lock Synchronization M Internal Internal / Line lock Frequency H:15.734KHz / V:59.94Hz Horizontal Resolution Color : 540 TV lines Min. Illumination 0.05Lux / 0.0004Lux (F1.
Item SCB-1000NA SCB-1000ND SCB-1000PA Low / Middle / High / Off White Balance ATW / Manual / AWC (1,800K° ~ 10,500K°) Electronic Shutter 1/60 ~ 1/120,000 sec Speed Mirror SCB-1000PD SCB-1000PH ● SPECIFICATIONS Gain Control 1/50 ~ 1/120,000 sec Off / On Environmental Operating Temperature / Humidity -10°C ~ +50°C (+14°F ~ +122°F) / Less than 90% RH Electrical Input Voltage/ Current 24VAC±10% 12VDC±10% 24VAC±10% Power Source Max. 3.5W Max. 2.5W Max. 3.5W Max. 2.5W Max. 4.
DECLARATION OF CONFORMITY Application of Council Directive(s) 2004 / 108 / EC Manufacturer's Name SAMSUNG TECHWIN CO., LTD Manufacturer's Address SAMSUNG TECHWIN CO., LTD 42, SUNGJU-DONG CHANGWON-CITY, KYUNGNAM, KOREA, 641-716 European Representative Name European Representative Address Equipment Type/Environment CCTV Camera Model Name SCB-1000PA, SCB-1000PD, SCB-1000PH, Beginning Serial NO.
MEMO H, ms pe
MEMO
MEMO
MEMO
MEMO
MEMO
MEMO
SALES NETWORK SAMSUNG TECHWIN CO., LTD. Samsungtechwin R&D Center, 701, Sampyeong-dong, Bundang-gu, Seongnam-si, Gyeonggi-do, Korea, 463-400 TEL : +82-70-7147-8740~60, FAX : +82-31-8018-3745 SAMSUNG TECHWIN AMERICA Inc. 1480 Charles Willard St, Carson, CA 90746, UNITED STATES Tol Free : +1-877-213-1222, FAX : +1-310-632-2195 www.samsungcctvusa.com www.samsungtechwin.com www.samsungsecurity.com SAMSUNG TECHWIN EUROPE LTD.
