COAXIAL REMOTE CONTROLLER User Manual SPC-300
W • COAXIAL REMOTE CONTROLLER User Manual Copyright ©2009 Samsung Techwin Co., Ltd. All rights reserved. Trademark is the registered logo of Samsung Techwin Co., Ltd. The name of this product is the registered trademark of Samsung Techwin Co., Ltd. Other trademarks mentioned in this manual are the registered trademark of their respective company. Restriction Samsung Techwin Co., Ltd shall reserve the copyright of this document.
Safety information CAUTION RISK OF ELECTRIC SHOCK. DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit.
Safety information CAUTION 1 1. Do not drop objects on the product or apply strong blows to it. Keep away from a location subject to excessive vibration or magnetic interference. 2 2. Do not install in a location subject to high temperature (over 50°C), low temperature (below -10°C), or high humidity. Doing so may cause fire or electric shock. 3 4 5 3. If you want to relocate the already installed product, be sure to turn off the power and then move or reinstall it. 6 4.
a g h nt) ms) ing. act. osal. Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, or other apparatus (including amplifiers) that produce heat. 9.
Contents IN Introduction Introduction 6 Part names and functions 7 T a ❖ Installation Checking Installation Environment 11 Installation precautions 11 Connection & Control To Control the camera coaxial communications 12 To control the camera using RS-485 device via coaxial communications 13 To control the camera using RS-232 device via coaxial communications 14 To control the camera using RS-485 signal output 15 To control the camera using RS-485 signal output via RS-232 communications 1
Introduction INTRODUCTION This remote controller can control A1 series cameras through A1 coaxial connection, and can control COAXITRON supporting cameras through COAXITRON communication. ❖ Features • Long-distance remote control Through RS-485 communication, remote control is possible up to 1.2 kilometers. • Easy Control Easy and simple 5-way keys for controlling the camera. ❖ List of controllable models • Capable of controlling A1 series camera products. • You can control cameras supporting COAXITRON.
Introduction PART NAMES AND FUNCTIONS ❖ Front Panel n o p POWER s STATUS POWER (X)1 23 23 901 (X)10 901 901 78 r 23 ON ON 1 2 1 2 3 4 5 6 7 8 TERMINATION PROTOCOL t 456 L 456 S 456 q 78 ADDRESS (X)100 ON 78 OFF CABLE COMPENSATION ❻ REMOTE CONTROLLER SPC-300 ❶ STATUS LED - Displays the status of the current operation. ❷ POWER LED - Switch to select the power source from DC 12 V or 4 AA batteries. ❸ POWER Switch - If you slide it to ON, the controller turns on.
ON ON 1 2 1 2 3 4 5 6 7 8 TERMINATION PROTOCOL - Use pin 1,2,3 of the Protocol setting switch to select a protocol. - The protocol switch pin 4 sets the protocol to COAXIAL or COAXITRON. - Use pin 5,6 of the Protocol setting switch to select a baud rate. - The protocol switch pin 7 sets the protocol to COAXIAL (BNC communication) or RS-485 output. - Use pin 8 of the Protocol setting switch to select RS-232 input.
Introduction PART NAMES AND FUNCTIONS ❖ ❖ Rear Panel ❶ ❷ - AA BATTERY You can use 4 AA-sized batteries for the power. ❸ - The average operation time is 20 hours based on the alkaline battery. (If the battery is discharged, it can cause a distortion of the video signal, or electric interference.) ❹ NOTE Remove the battery if you do not use the controller for a longer period. Otherwise, it may cause damage to the controller from a leak of the battery solution.
Introduction ❖ Top REMOTE CONTROLLER SCP-300 TERMINATION 1 2 ON S OFF PROTOCOL 1 2 3 4 5 6 7 8 ON L CABLE COMPENSATION ADDRESS (X)100 ON (X)10 (X)1 POWER STATUS RS-232C n TX o POWER RS-485 VIDEO RX p OUT DC 12V IN q r ❶ USB Port - This terminal is used for updating the product’s firmware. ❷ RS-232 Port (9-pin D SUB) - Used to control remotely using RS-232 communication. ❸ RS-485 Port (4-pin) - Used to control remotely using RS-485 communication.
Installation CHECKING INSTALLATION ENVIRONMENT • Please check the following instructions before installation for your safety. T K • The way of connecting the main product with external devices (COAXIAL BNC) is very important to build up a proper system. • Do not disassemble the unit; doing so could expose you to dangerous high voltage points. INSTALLATION PRECAUTIONS • Make sure you turn off the product before installation.
Connection & Control TO CONTROL THE CAMERA USING CONTROL MENU KEYS AND COAXIAL / COAXITRON OUTPUT REMOTE CONTROLLER SCP-300 TERMINATION SCX-RD100 1 2 ON S OFF PROTOCOL 1 2 3 4 5 6 7 8 ON L CABLE COMPENSATION ON ADDRESS (X)100 (X)10 (X)1 POWER POWER STATUS 1. Connect the product to DC 12V power source or insert 4 AA-sized batteries into the battery compartment. (Power can be supplied via USB cable connection.) 2.
Connection & Control TO CONTROL THE CAMERA USING RS-485 INPUT AND COAXIAL / COAXITRON OUTPUT T V REMOTE CONTROLLER SCP-300 TERMINATION 1 2 ON S OFF PROTOCOL 1 2 3 4 5 6 7 8 ON L CABLE COMPENSATION ON ADDRESS (X)100 (X)10 (X)1 POWER POWER STATUS 1. Connect the product to DC 12V power source or insert 4 AA-sized batteries into the battery compartment. (Power can be supplied via USB cable connection.) 1 2. Connect the VIDEO IN of the unit and VIDEO OUT of the AI Camera directly.
TO CONTROL THE CAMERA USING RS-232 DEVICE VIA COAXIAL COMMUNICATIONS REMOTE CONTROLLER SCP-300 TERMINATION 1 2 ON S OFF PROTOCOL 1 2 3 4 5 6 7 8 ON L CABLE COMPENSATION ON ADDRESS (X)100 (X)10 (X)1 POWER POWER STATUS of Connection & Control 1. Connect the product to DC 12V power source or insert 4 AA-sized batteries into the battery compartment. (Power can be supplied via USB cable connection.) 2. Set the protocol switches 7 and 8 to ON. 3.
Connection & Control TO CONTROL THE CAMERA USING RS-485 OUTPUT AND CONTROL MENU KEYS T O REMOTE CONTROLLER SCP-300 TERMINATION 1 2 ON S OFF PROTOCOL 1 2 3 4 5 6 7 8 ON L CABLE COMPENSATION ON ADDRESS (X)100 (X)10 (X)1 POWER POWER STATUS 1. Connect the product to DC 12V power source or insert 4 AA-sized batteries into the battery compartment. (Power can be supplied via USB cable connection.) 1 2. Connect the RX(+/-) of the unit to the RS-485 (+/-) port of the camera. 2 3.
Connection & Control TO CONTROL THE CAMERA USING RS-485 SIGNAL OUTPUT VIA RS-232 COMMUNICATIONS REMOTE CONTROLLER SCP-300 TERMINATION 1 2 ON S OFF PROTOCOL 1 2 3 4 5 6 7 8 ON L CABLE COMPENSATION ON ADDRESS (X)100 (X)10 (X)1 POWER POWER STATUS 1. Connect the product to DC 12V power source or insert 4 AA-sized batteries into the battery compartment. (Power can be supplied via USB cable connection.) 2. Set the protocol switch 8 to ON. 3.
Connection & Control SWITCH SETTING TABLE ❖ Use a combination of pin 1,2,3 of the Protocol setting switch to select a protocol.
Connection & Control – See the following table to set the baud rate. ON ON 1 2 1 2 3 4 5 6 7 8 TERMINATION PROTOCOL BAUD RATE PIN 5 PIN 6 38400 BPS OFF OFF 19200 BPS ON OFF 9600 BPS OFF ON 4800 BPS ON ON t.
Specifications SPECIFICATIONS D Item Description Communication Method COAXIAL / COAXITRON INTERFACE Range Max. 500m (with 5C-2V cable) Connector Type D-SUB 9P COAXIAL Port 1 Port BAUD RATE 4800/9600/19200/38400bps (Only Samsung protocol supported) Connector Type 4P Terminal Type RS-232 Port 1 Port BAUD RATE 4800 / 9600 / 19200 / 38400 bps RS-485 USB PORT(USB2.0) S/W PROGRAM UPLOAD Composite Video 1.
Specifications DIMENSIONS Unit (mm) English 21
SALES NETWORK SAMSUNG TECHWIN CO., LTD. Samsungtechwin R&D Center, 701, Sampyeong-dong, Bundang-gu, Seongnam-si, Gyeonggi-do, Korea, 463-400 TEL : +82-70-7147-8740~60, FAX : +82-31-8018-3745 SAMSUNG TECHWIN AMERICA Inc. 1480 Charles Willard St, Carson, CA 90746, UNITED STATES Tol Free : +1-877-213-1222, FAX : +1-310-632-2195 www.samsungcctvusa.com www.samsungtechwin.com www.samsungsecurity.com SAMSUNG TECHWIN EUROPE LTD.
