SyncMaster 400DX-3/460DX-3 LCD Display User Manual The color and the appearance may differ depending on the product, and the specifications are subject to change without prior notice to improve the performance.
Safety Instructions Notational Note These safety instructions must be followed to ensure your safety and prevent property damage. Make sure to read the instructions carefully and use the product in the correct manner. Warning / Caution Failure to follow directions noted by this symbol could result in bodily harm or damage to the equipment.
Safety Instructions Ensure that the power plug is plugged into the power outlet firmly and correctly. • Otherwise, this may result in fire. Do not forcefully bend or pull the power plug and do not place any heavy material on it. • Otherwise, this may result in fire. Do not connect multiple appliances to the same power outlet. • Otherwise, this may cause fire due to overheating. Do not disconnect the power cord while using the product.
Safety Instructions DO NOT PLACE CANDLES, MOSQUITO REPELLANT, CIGARETTES AND ANY HEATING APPLIANCES NEAR THE PRODUCT. • Otherwise, this may result in fire. Keep heating appliances as far away from the power cord or the product as possible. • Otherwise, this may result in electric shock or fire. Do not install it in a badly ventilated location such as a bookcase or closet. • Otherwise, this may result in fire due to an increase in the internal temperature.
Safety Instructions When cleaning the power plug pins or dusting the power outlet, clean it with a dry cloth. • Otherwise, it may result in fire. When cleaning the product, make sure to disconnect the power cord. • Otherwise, it may result in electric shock or fire. When cleaning the product, disconnect the power cord and clean it with a soft, dry cloth. • (Do not use chemicals such as wax, benzene, alcohol, thinner, mosquito repellant, lubricant, or cleaner.
Safety Instructions If thunder or lightning is occurring, do not touch the power cord or antenna cable. • Otherwise, this may result in electric shock or fire. Do not try to move the monitor by pulling only the wire or the signal cable. • Otherwise, it may fall and result in electric shock, damage to the product or fire due to damage to the cable. Do not lift or move the product back and forwards or right and left while only holding the power cord or signal cables.
Safety Instructions To avoid eyestrain, do not sit too close to the product. Take a rest for at least five (5) minutes after using the monitor for one (1) hour. This reduces eye fatigue. Do not install it in an unstable location such as an unstable rack or uneven surface or a location exposed to vibrations. • Otherwise, it may fall and cause personal injury and/or damage the product. • If you use the product in a location exposed to vibrations, it may damage the product and result in fire.
Safety Instructions The batteries (and rechargeable batteries) are not ordinary refuse and must be returned for recycling purposes. The customer is responsible for returning the used or rechargeable batteries for recycling. • The customer can return used or rechargeable batteries to a nearby public recycling center or to a store selling the same type of the battery or rechargeable battery. Do not place the product in a location exposed to direct sunlight or near any heat such as a fire or heater.
Safety Instructions Do not put any heavy objects on the product. • This may result in personal injury and/or damage to the product.
Introduction Package Contents Checking the Contents of the Package Remove the lock from the package box, as shown in the figure above. Lift up the package box by Check the contents of the holding the grooves on package. both sides of the package box. Remove the Styrofoam and vinyl cover. Note • After unpacking the package, make sure to check the contents of the package. • Store the packaging box in case you need to move the Product later. • If any items are missing, contact your dealer.
Introduction Manuals Quick Setup Guide Warranty Card User Manual (Not available in all locations) Cables Power Cord D-Sub Cable Others Remote Control Batteries (AAA X 2) (BP59-00138B) (Not available in all locations) Sold separately Semi Stand KIT LAN Cable USB Cable RGB to BNC Cable RGB to COMPONENT Cable Network Box
Introduction Sold separately Wall Mount KIT TV Tuner Box (US Only) HDMI Cable HDMI-DVI Cable Your LCD Display Front MENU button [MENU] Opens the on-screen menu and exits from the menu. Also use to exit the OSD menu or return to the previous menu. Navigate buttons (Up-Down buttons) Moves from one menu item to another vertically or adjusts selected menu values. Adjust buttons (Left-Right buttons) / Volume buttons Moves from one menu item to another horizontally or adjusts selected menu values.
Introduction However, the picture may display abnormally if the connected external input signal is different from the selected video signal. • A TV tuner box (sold separately) must be connected to use the TV. (US Only) • MagicInfo can only be enabled when a network box is connected. PIP button Push the PIP button to turn the PIP screen On / Off.
Introduction POWER S/W ON [ │ ] / OFF Switches the LCD Display On/Off. POWER The power cord plugs into the LCD Display and the wall outlet. IR OUT/IN Receives a signal from the remote control and outputs the signal through Loopout when a removable sensor board is connected. DVI OUT (LOOPOUT) • Connect a monitor to another monitor through a DVI, DVI to HDMI cable. • Connect a DVI or DVI-HDMI cable to [DVI OUT (LOOPOUT)] on the product and [DVI IN] or [HDMI IN] on another monitor.
Introduction • The status of the cable may have a great effect on the Loopout performance. RGB/COMPONENT IN (PC/COMPONENT Connection Terminal (Input)) • Connect the [RGB/COMPONENT IN] port on the monitor to the RGB port on the PC using the D-SUB cable. • Connect the [RGB/COMPONENT IN] port on the monitor to the COMPONENT port on the external device using the RGB to COMPONENT cable. • Connect the [RGB/COMPONENT IN] port on the monitor to the BNC port on the PC using the RGB to BNC cable.
Introduction Connect a headphone or an External speaker. DC OUT Make sure to use connecting [DC OUT] terminal to the authorized TV-Tuner Box. (US Only) Otherwise, this may result in damage to the product. HDMI IN 1 • Connect the [HDMI IN 1] terminal at the back of your LCD Display to the HDMI terminal of your digital output device using a HDMI cable. • Up to HDMI 1.3 can be supported. Note • A normal external device (DVD player or camcorder, etc.
Introduction RJ 45 MDC (MDC PORT) MDC(Multiple Display Control) Program Port Connect the LAN cable to [RJ45 MDC] on the product and LAN on the PC. To use an MDC, the MDC program must be installed on the PC. Note Go to Multi Control and select RJ45 MDC as the MDC Connection. RS232C OUT/IN (RS232C Serial PORT) MDC(Multiple Display Control) Program Port Connect a serial cable (cross type) to [RS232C] on the product and RS232C on the PC. To use an MDC, the MDC program must be installed on the PC.
Introduction Note • You must purchase the Kensington Lock separately. • These are general instructions. For exact instructions, see the User Manual supplied with the locking device. • You can purchase the locking device from an electronics store, an online shop, or our service center. Connecting a Network Box (sold separately) PC OUT MagicInfo video output port MAGICINFO OUT This is the output terminal for the video, audio, and control signals of MagicInfo.
Introduction Connects to a mains socket via the power cord. POWER S/W ON [ I ] / OFF Turns the network box on or off. Note The power switches of both of the monitor and the network box must be turned on for the network box to operate normally. Remote Control Note • The performance of the remote control may be affected by a TV or other electronic device operating near the LCD Display , causing a malfunction due to interference with the frequency.
Introduction POWER OFF Number Buttons Turns the product On/Off. Turns the product Off. Used to enter the password during the OSD adjustment or to use MagicInfo. Press to change the channel. / GUIDE button The "-" button is used to select Digital channels. Electronic Program Guide (EPG) display. - This function does not work for this LCD Display. Adjusts the audio volume. + VOL SOURCE Selects a connected external input source or MagicInfo mode. Press the button to change the input signal SOURCE.
Introduction FM Stereo Mono Mono Stereo Mono ↔ Stereo Manual Change SAP Mono ↔ SAP Mono DUALSTEREO/MONO, DUAL l / DUAL ll and MONO/NICAM MONO/NICAM STEREO can be operated depending on the broadcasting type by using the DUAL button on the remote control while watching TV. - This is activated when a TV tuner box is installed. ENTER/PRE-CH This button is used to return to the immediately previous channel. - This is activated when a TV tuner box is installed.
Introduction 1 2 1. The product can be tilted up to 15 degrees from a vertical wall. 2. To use the product in portrait mode, rotate it clockwise so that the LED indicator is at the bottom. Ventilation requirement 1. Vertical wall mount condition A : min.
Introduction 2. Embedded Mount guide A : min. 40 mm B : min. 70 mm C : min. 50 mm D : min. 50 mm E : Ambient temperature Measuring point <35℃ • When embedding the product in a wall, be sure there is some space behind the product for ventilation, as shown above, and maintain the ambient temperature at 35℃ or lower. Note A Samsung Electronics service center can provide details. 3. Floor mount guide A : min.
Introduction Mechanical Layout Installation VESA Bracket • When installing VESA, make sure to comply with the international VESA standards. • Purchasing VESA Bracket and Installation Information : Please contact your nearest SAMSUNG Distributor to place an order. After your order is placed, installation professionals will visit you and install the bracket. • At least 2 persons are needed in order to move the LCD Display.
Introduction Dimensions Notice For securing the bracket on a wall, use only machine screws of 6 mm diameter and 8 to 12 mm length.
Introduction • Dimension with welcome board
Introduction • Dimension with other accessories Wall Bracket Installation • Contact a technician for installing the wall bracket.
Introduction • SAMSUNG Electronics is not responsible for any damages to the product or harm to customers when the installation is done by the customer. • This product is for installing on cement walls. The product may not stay in place when installed on plaster or wood. Components Only use the components and accessories shipped with the product.
Introduction 4. Remove safety pin (3) and insert the 4 product holders into the corresponding bracket holes (1). Then place the product(2) so that it is firmly fixed to the bracket. Make sure to re-insert and tighten the safety pin (3) to securely hold the product to the bracket. A- LCD Display B- Wall Bracket C- Wall Wall Bracket Angle Adjustment Adjust the bracket angle to -2° before installing it on the wall. 1. Fix the product to the wall bracket. 2.
Introduction Make sure to use the top center, and not the left or the right side of the product to adjust the angle. Remote Control (RS232C) Cable connections interface RS232C(9 pin) pin TxD(No.2) RxD(No.3) GND(No.
Introduction • RS232C cable Connector : 9-pin D-Sub Cable : Cross (reversed) cable -P1FEMALE • -P1- -P2- -P2- Rx 2 ---------> 3 Rx Tx 3 <--------- 2 Tx Gnd 5 ---------- 5 Gnd FEMALE Connecting method Control codes • • • Get control Header command 0xAA command type DATA Length ID 0 CheckSum Set control Header command 0xAA command type ID DATA Length DATA 1 Value CheckSum commanding words No.
Introduction 1 Power control 0x11 0~1 2 Volume control 0x12 0~100 3 Input source control 0x14 - 4 Screen Mode control 0x18 - 5 Screen Size control 0x19 0~255 6 PIP on/off control 0x3C 0~1 7 Auto adjustment control 0x3D 0 8 Video wall Mode control 0x5C 0~1 9 Safety Lock 0x5D 0~1 - ID should show hexadecimal value of assigned ID, but ID 0 should be 0xFF. - Every communication will be made in hexadecimals and Checksum is the sum of all remainings.
Introduction • Ack Header command 0xAA 0xFF ID DATA Length Ack/Nak r-CMD Val1 3 ‘A’ 0x11 Power DATA Length Ack/Nak r-CMD Val1 3 ‘N’ 0x11 ERR Check Sum Power : Same as above • Nak Header command 0xAA 0xFF ID Check Sum ERR : Error code that shows what occurred error is • Volume Control • Function Personal Computer changes volume of TV / Monitor.
Introduction • Input Source Control • Function Personal Computer changes input source of TV / Monitor.
Introduction 0xAA 0xFF 3 ‘A’ 0x14 Input Source DATA Length Ack/Nak r-CMD Val1 3 ‘N’ 0x14 ERR Input Source : Same as above • Nak Header command 0xAA 0xFF ID Check Sum ERR : Error code that shows what occurred error is • Screen Mode Control • Function Personal Computer changes "Screen Mode" of TV/Monitor. Cannot be controlled when Video Wall is on. Caution Only works with models include TV.
Introduction • Nak Header command 0xAA 0xFF ID DATA Length Ack/Nak r-CMD Val1 3 ‘N’ 0x18 ERR Check Sum ERR : Error code that shows what occurred error is • Screen Size Control • Function Personal Computer recognizes the screen size of TV / Monitor.
Introduction • Set the PIP ON / OFF Header command ID 0xAA 0x3C DATA Length DATA 1 PIP CheckSum PIP : The PIP ON / OFF code to set for the TV or Monitor 1 : PIP ON 0 : PIP OFF • Ack Header command 0xAA 0xFF ID DATA Length Ack/Nak r-CMD Val1 3 ‘A’ 0x3C PIP DATA Length Ack/Nak r-CMD Val1 3 ‘N’ 0x3C ERR Check Sum PIP : Same as above • Nak Header command 0xAA 0xFF ID Check Sum ERR : Error code that shows what occurred error is • Auto Adjustment Control (PC, BNC Only) •
Introduction 0xFF 3 ‘A’ 0x3D Auto Adjustment Header command DATA Length Ack/Nak r-CMD Val1 0xAA 0xFF 3 ‘N’ 0x3D ERR 0xAA • Nak ID Check Sum ERR : Error code that shows what occurred error is • Video Wall Mode Control • Function Personal Computer converts Video Wall Mode of TV / Monitor when Video Wall is ON. Only works with TV / Monitor where Video Wall is on.
Introduction Header command 0xAA 0xFF ID DATA Length Ack/Nak r-CMD Val1 3 ‘N’ 0x5C ERR Check Sum ERR : Error code that shows what occurred error is • Safety Lock • Function Personal Computer turns Safety Lock function of TV / Monitor ON / OFF. Can operate regardless of whether power is ON / OFF.
Connections Connecting a Computer There are several ways to connect the computer to the monitor. Choose one from the following options. Using the D-sub (Analog) connector on the video card. • Connect the D-sub to the 15-pin, [RGB/COMPONENT IN] port on the back of your LCD Display and the 15 pin D-sub Port on the computer. Using the DVI (Digital) connector on the video card. • Connect the DVI Cable to the [DVI IN] port on the back of your LCD Display and the DVI port on the computer.
Connections Note Select HDMI2 or HDMI1 as an input source when connected to the PC via an HDMI cable. To obtain normal picture and audio from the PC, HDMI2 or HDMI1 must be selected before PC is selected in Edit Name. To enable audio when DVI Device is selected, be sure to establish the connection using step( ). Connect the Audio cable for your LCD Display to the AUDIO port on the back of the LCD Display. Connect the power cord for your LCD Display to the POWER port on the back of the LCD Display.
Connections Connect between the [DVI OUT(LOOPOUT)] port on the LCD Display and the input port on another monitor using a DVI cable. Connect between the [AUDIO OUT] port on the LCD Display and the audio input port on another monitor using a stereo cable. Note • Select DVI Mode as an input source for the external monitor connected to [DVI OUT]. • DVI OUT does not support HDCP. Connecting AV Devices 1.
Connections Connecting to a Camcorder 1. Locate the AV output jacks on the camcorder. They are usually found on the side or back of the camcorder. Connect a video cable between the VIDEO OUTPUT jack on the camcorder and the [AV IN] on the LCD Display . 2. Connect a set of audio cables between the AUDIO OUTPUT jacks on the camcorder and the [AV /COMPONENT AUDIO IN [R-AUDIO-L]] on the LCD Display . 3. Press SOURCE on the product or remote control and select "AV". 4.
Connections Connecting Using a HDMI Cable 1. Connect an HDMI cable to [HDMI IN 2 (MAGICINFO)] or [HDMI IN 1] on the product and the HDMI output port on a digital device. 2. Press SOURCE on the product or remote control and select "HDMI1 / HDMI2" Note In HDMI mode, only PCM format audio is supported. Connecting Using a DVI to HDMI Cable Connect a DVI-HDMI cable to [HDMI IN 2 (MAGICINFO)] or [HDMI IN 1] and the DVI output port on the digital device.
Connections Note Press SOURCE on the product or remote control and select "HDMI1 / HDMI2" Connecting a DVD Player Connect a RGB to Component cable between the [RGB/COMPONENT IN] port on the LCD Display and the PR, Y, PB jacks on the DVD player. Connect a set of audio cables between the [AV/COMPONENT AUDIO IN [R-AUDIO-L]] on the LCD Display and the AUDIO OUT jacks on the DVD player. Note • Press SOURCE on the product or remote control and select "Component".
Connections Connecting a DTV Set Top (Cable/Satellite) Box Connect a RGB to Component cable between the [RGB/COMPONENT IN] port on the LCD Display and the PR, Y, PB jacks on the Set Top Box. Connect a set of audio cables between the [AV/COMPONENT AUDIO IN [R-AUDIO-L]] on the LCD Display and the AUDIO OUT jacks on the Set Top Box. Note • Press SOURCE on the product or remote control and select "Component". • For an explanation of Component video, see your Set Top Box owner's manual.
Connections Connecting a Network Box (sold separately) Note • Network boxes are sold separately. • For more information on how to purchase and install a network box, contact Samsung Electronics. Connecting the Power Connect the [POWER] terminal of the product and the [POWER] terminal of the installed network box using a power extension cable. Connect the power cord to [POWER] on the network box and mains socket. Turn on the power switch. Connecting to MAGICINFO OUT 1.
Connections Connecting a LAN Cable 1. Connect the LAN cable between the [LAN] port on the product and the [LAN] port on your PC. Connecting a USB devices 1. You can connect USB devices such as a mouse or keyboard.
Using the Software Monitor Driver Note When prompted by the operating system for the monitor driver, insert the CDROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions appropriate for the operating system you have. Prepare a blank disk and download the driver program file at the Internet web site shown here. Internet web site : http://www.samsung.com/ Installing the Monitor Driver (Automatic) 1.
Using the Software Note This monitor driver is certified by Microsoft, and installing it will not damage your system. The certified driver will be posted on Samsung Monitor homepage. http://www.samsung.com/ Installing the Monitor Driver (Manual) Microsoft® Windows Vista™‚ Operating System 1. Insert your Manual CD into your CD-ROM drive. 2. Click (Start) and "Control Panel". Then, double-click on "Appearance and Personalization". 3. Click "Personalization" and then "Display Settings". 4.
Using the Software If the message "Windows needs..." is displayed, as shown in the figure below, click "Continue". Note This monitor driver is under certifying MS logo, and this installation will not damage your system. The certified driver will be posted on Samsung Monitor homepage. http://www.samsung.com/ 6. Click "Update Driver..." in the "Driver" tab. 7. Check the "Browse my computer for driver software" checkbox and click "Let me pick from a list of device drivers on my computer". 8.
Using the Software 9. Select the model that matches your monitor from the list of monitor models on the screen, and click "Next". 10. Click "Close" → "Close" → "OK" → "OK" on the following screens displayed in sequence.
Using the Software 1. Insert CD into the CD-ROM drive. 2. Click "Start" → "Control Panel", then click the "Appearance and Themes" icon. 3. Click "Display" icon and choose the "Settings" tab then click "Advanced...". 4. Click the "Properties" button on the "Monitor" tab and select "Driver" tab. 5. Click "Update Driver..." and select "Install from a list or..." then click "Next" button. 6. Select "Don't search, I will...", then click "Next" and then click "Have disk".
Using the Software 7. Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next" button. 8. If you can see the following message window, then click the "Continue Anyway" button. Then click "OK" button. Note This monitor driver is certified by Microsoft, and this installation will not damage your system. The certified driver will be posted on Samsung Monitor homepage. http://www.samsung.com/ 9.
Using the Software 10. Monitor driver installation is completed. Microsoft® Windows® 2000 Operating System When you can see "Digital Signature Not Found" on your monitor, follow these steps. 1. Choose "OK" button on the "Insert disk" window. 2. Click the "Browse" button on the "File Needed" window. 3. Choose A:(D:\Driver), then click the "Open" button and then click "OK" button. How to install 1. Click "Start", "Setting", "Control Panel". 2. Double click the "Display" icon. 3.
Using the Software If you can see the "Digital Signature Not Found" window, then click the "Yes" button. Then click the "Finish" button and the "Close" button. Microsoft® Windows® Millennium Operating System 1. Click "Start", "Setting", "Control Panel". 2. Double click the "Display" icon. 3. Select the "Settings" tab and click "Advanced Properties" button. 4. Select the "Monitor" tab. 5. Click the "Change" button in the "Monitor Type" area. 6. Choose "Specify the location of the driver". 7.
Using the Software 5. Set a Keyboard for your computer. 6. The next screen is for setting your monitor. 7. First of all, set a horizontal frequency for your monitor. (You can enter the frequency directly.) 8. Set a vertical frequency for your monitor. (You can enter the frequency directly.) 9. Enter the model name of your monitor. This information will not affect the actual execution of X-Window. 10. You have finished setting up your monitor.
MDC Program Installation/Uninstallation Installation 1 2 Insert the installation CD into the CD-ROM drive. Click the MDC Unified installation program. If a software installation window is not displayed on the main screen, install with the "MDC Unified" execution file in the MDC folder on the CD. 3 4 Click "Next" in the displayed Installation Wizard screen. In the "License Agreement" window displayed, select "I accept the terms in the license agreement" and click "Next".
What is MDC? Multiple display control "MDC" is an application that allows you to easily control multiple display devices simultaneously using a PC. Connecting to MDC Using MDC via RS-232C (serial data communications standards) An RS-232C serial cable must be connected to the serial ports on the PC and monitor.
Using MDC via Ethernet Enter the IP for the primary display device and connect the device to the PC. One display device can connect to another using an RS-232C serial cable.
Connection Management Connection management includes the Connection list and Connection list modification options. Connection list – Connection list shows the details of the connections such as connection setting (IP/ COM, Port No, MAC, and Connection Type), connection status, Set ID Range, and detected devices. Each connection can contain a maximum of 100 devices connected in serial daisy-chain fashion.
Auto Set ID Auto Set ID feature assigns a Set ID for all the LFDs connected in daisy-chain of a selected connection. There can be a maximum of 100 LFDs in a connection. The Set ID is assigned sequentially in the daisychain running from 1 to 99, and then finally to Set ID 0. Cloning Using the Cloning feature, you can copy the setting of one LFD and apply it to multiple selected LFDs. You can select specific tab categories or all tab categories for cloning, using the copy setting option window.
Command Retry This feature is used to specify the maximum number of times the MDC command will be retried in case of there being no reply or a corrupted reply from an LFD. The retry count value can be set using the MDC options window. The retry count value must be between 1-10. The default value is 1.
Getting Started with MDC 1 To start the program, click Start 2 Click Add to add a display device. Programs Samsung MDC Unified. If the connection is established via RS232C, go to Serial and specify the COM Port.
If the connection is established via Ethernet, enter the IP that was entered for the display device.
Main Screen Layout 1 6 5 4 2 3 1 Menu Bar Change the status of a display device or the properties of the program. 2 Device Category View a list of connected display devices or device groups. 3 Schedule Category View a list of schedules for display devices. 4 Set List Select the display device you want to adjust. 5 Modify the Set List Add, edit, regroup or delete sets. 6 Help Topics Display help topics for the program.
Menus You can power on or off a selected device or change the input source or volume of the device. Choose display devices from the list of sets, and select the Home tab. 1 Home Select an item and change the corresponding setting. Power On: Power on a selected display. Off: Power off a selected dis Input Input Source : Change the input source. Input sources available can vary depending on the Display Device Models. The input source can be changed only for displays that are turned on.
This menu shows a list of display devices which have following errors - fan error, temperature error, brightness sensor error, or lamp error. Select a display device from the list. The Repair button will be enabled. Click the refresh button to refresh the error status of the display device. The recovered display device will disappear from the Fault Device List. Fault Device Alert Display device in which error is detected will be reported by email. Fill in all required fields.
Screen Adjustment The screen settings (contrast, brightness, etc.) can be adjusted. Choose display devices from the list of sets, and select the Picture tab. Custom Select an item and change the corresponding screen setting. Color and Tint are not available if the input source is PC. Red, Green, Blue and PC Screen Adjustment are not available if the input source is Video.
Options Dynamic Contrast Adjust the Dynamic Contrast for the selected display device. Gamma Control Change the gamma value for the selected display. Auto Motion Plus This option is used to view dynamic images. Off: Disable the Auto Motion Plus function. Clear: Set the level of Auto Motion Plus to clear. This mode is suitable to display vivid images. Standard: Set the level of Auto Motion Plus to standard. Smooth: Set the level of Auto Motion Plus to smooth.
Size Picture Size Adjust the screen size for the selected display device. The Detail item will be disabled if Picture Size is set to a mode that does not support detailed configuration. The -/+ buttons can be used to adjust Zoom. The screen can be relocated using the up/down/left/right buttons. Detail You can view details of the selected screen size. PC Screen Adjustment Frequency adjustment or fine-tuning is available by using the -/+ buttons in Coarse or Fine.
Sound Adjustment You can change the sound settings. Choose display devices from the list of sets, and select the Sound tab. The Bass or Treble item will be disabled if the item is not supported by the selected set. Bass Adjust the bass for the selected display. Treble Adjust the treble for the selected display. Balance (L/R) Adjust the volume of the left and right speakers of the selected display device. SRS TS XT Enable or disable the SRS TS XT effect for the selected display device.
3.6.11 System Setup Choose display devices from the list of sets, and select the System tab. Video Wall The Video Wall function can be used to display part of a whole picture or repeat the same picture on each of connected multiple display devices. Video Wall is enabled only when devices are in the group. Video Wall Enable or disable Video Wall. Format Select the format to display the split screen.
H Select the number of horizontal display devices. A maximum of 15 displays can be arranged in a row. A maximum of 6 can be assigned to V if 15 is assigned to H. V Select the number of vertical display devices. A maximum of 15 displays can be arranged in a row. A maximum of 6 can be assigned to V if 15 is assigned to H. Screen Position View the layout of displays (configured by the screen divider) or change the layout as required. Screen Position and Preview are enabled when Video Wall is set to on.
PIP Basic information required to adjust PIP will appear in the menu screen. PIP will be disabled when Video Wall is ON. Note that Picture Size is disabled when PIP is ON. PIP Size View the PIP Size of the current display. PIP Source Select a PIP input source. Sound Select Select and enable the sound from either the primary screen or secondary screen. Channel The channel can be changed if PIP Source is TV.
General User Auto Color Automatically adjust the screen colors. Available only in PC mode. Auto Power Set the product to automatically power on. Standby Control Set the standby mode to activate if an input source is not detected. Fan & Temperature Configure the settings required to detect the fan speed and internal temperature for the product's protection. Fan Control Select a method to configure the fan speed. Fan Speed Configure the fan speed.
Security Safety Lock Lock the on-screen menus. To unlock the menus, set Safety Lock to Off. Button Lock Lock the buttons on the display device. To unlock the buttons, set Button Lock to Off. OSD Display Source OSD Select whether to display a message when the Source is changed. Not Optimum Mode OSD Select whether to display a message when a non-compatible mode is selected. No Signal OSD Select whether to display a message when there is no input signal.
Time Clock Set Change the current time on the selected display device according to the time set on a PC. If the time is not set on the display device, null values will be displayed. Timer On Time: Set the time to power on the selected display device. Off Time: Set the time to power off the selected display device. Volume: Specify the volume of the display device when it is powered on by On Time. Source: Specify the input source of the display device when it is powered on by On Time.
Once: Activate the timer only one time. EveryDay: Activate the timer every day. Mon~Fri: Activate the timer from Monday through Friday. Mon~Sat: Activate the timer on Saturdays and Sundays. Manual: Customize days of the week. The checkboxes to select days of the week below Repeat are enabled only if Manual is selected. Holiday Management Holiday Management allows you to prevent devices that are set to be powered on by the Timer from turning on at a specified date.
Screen Burn Protection Pixel Shift Move the screen slightly at specified time intervals to prevent screen burn-in. Screen Saver This function prevents screen burn-in when the screen of the selected display device is left idle for an extended period of time. Interval: Set the interval to activate the Screen Saver. Mode: The Time setting can vary for each Mode.
The Safety Screen function can be used to prevent screen burn-in when a stationary image displays on the screen of a display device for an extended period of time. Lamp Control Lamp Control is used to adjust the backlight to reduce power consumption. Automatically adjust the backlight of the selected display device at a specified time. If Manual Lamp Control is adjusted, Auto Lamp Control will automatically switch to Off. Manually adjust the backlight for the selected display.
2 Reset Reset Picture Reset the screen settings. Reset Sound Reset the sound settings. Reset System Reset the system settings. Reset All Reset the screen, sound and system settings at the same time. 3 Edit Column Select the items you want to display in the list of sets. 4 Information View the program information.
3.6.13 Other Functions Resizing a Window Place the mouse pointer on a corner of the program window. An arrow will appear. Move the arrow to customize the size of the program window.
Group Management Creating Groups Create groups and manage the list of sets on a group basis. Duplicate group names cannot be used. 1 Right-click and select Group>Edit in the display device list section on the left side of the program window. 2 In the Edit Group window displayed, click Add on the sub level or Add on the same level. Add on the sub level: Create a sub-group under the selected group. Add on the same level: Create a group on the same level as the selected group.
The Add on the same level button is enabled only if at least one group is created. 3 Enter the group name. Deleting Groups 1 2 Select a group name, and click Edit. 3 Click Yes. The group will be deleted. In the Edit Group window displayed, click Delete. Renaming Groups 1 2 Select a group name, and click Edit. 3 If a cursor appears in the old group name, enter a new group name. In the Edit Group window displayed, click Rename.
Schedule Management Creating Schedules Create and register a schedule on a group basis. 1 Click All Schedule List in the schedule section on the left side of the program window. The Add button will be enabled in the middle. 2 Click the Add button. The Add Schedule window will appear.
3 Click Add below the Device Group item, and select the group you want to add a schedule to. 4 Select Date&Time/Action and click OK. The schedule will be added and a list of schedules will appear in the set list window. Device Group: Select a group. Date&Time Instant Execution: Run the schedule immediately. Timer Set the date, time and interval to run the schedule. Action: Select a function that will activate at the specified time and interval.
Troubleshooting Guide Issue The display you want to control does not appear on the system information chart. Solution 1. Check the connection of the RS232C cable (check that the cable is properly connected to appropriate serial port). 2. Check that another display with a duplicate ID is not connected. Connecting displays with a duplicate ID can cause the displays not to be shown due to data collision. 3. Check that the display ID is within the range of 0 and 99. (Change the ID using the Display menu.
How display properties are shown when multiple displays are used 1 2 3 When no display is selected: The default value is displayed. When one display is selected: Settings for the selected display are displayed. When two displays are selected (e.g. in sequence of ID 1 andID 3): The settings for ID 1 are displayed before the settings for ID 3. 4 When the All+Select checkbox is checked and all displays are selected: The default settings are displayed.
Adjusting the LCD Display Input Available Modes • PC / DVI / DisplayPort • AV • Component • HDMI • MagicInfo • TV Note • A TV tuner box (sold separately) must be connected to use the TV. (US Only) • MagicInfo can only be enabled when a network box is connected. Source List Use to select PC, HDMI or other external input sources connected to the LCD Display. Use to select the screen of your choice. 1. PC 2. DVI 3. AV 4. Component 5.
Adjusting the LCD Display However, the picture may display abnormally if the connected external input signal is different from the selected video signal. PIP Note The PIP function is not available when Video Wall is On. When external AV devices such as VCRs or DVDs are connected to the LCD Display , PIP allows you to watch video from those devices in a small window super-imposed on the PC Video signal. (Off/On) Note • PIP turns off when the LCD Display is switched to an external source.
Adjusting the LCD Display • HDMI : PC • DisplayPort : PC Size Changes the Size of the PIP window. Note will be changed to <16:9> when is . Position Changes the Position of the PIP window. Transparency Adjusts the Transparency of PIP windows.
Adjusting the LCD Display Edit Name Name the input device connected to the input jacks to make your input source selection easier. VCR / DVD / Cable STB / HD STB / Satellite STB / AV Receiver / DVD Receiver / Game /Camcorder / DVD Combo / DHR / PC / DVI PC / DVI Devices Note • The displayed devices differ depending on the external input mode. • When connecting a PC to the HDMI terminal, set Edit Name to PC. In other cases, set Edit Name to AV.
Adjusting the LCD Display Source AutoSwitch When the Source AutoSwitch is On, the display video source will automatically be searched for active video. The Primary Source selection will be activated, if the current video source is not recognized. Secondary source selection will become active, if no primary video source is available. If the primary or secondary source is not recognized, the display will search again, if no active video is found the display will show the no-input-signal message.
Adjusting the LCD Display Specify Primary Source for the automatic input source. Secondary Source Specify Secondary Source for the automatic input source. Picture [PC / DVI / DisplayPort / MagicInfo Mode] Available Modes • PC / DVI / DisplayPort • AV • Component • HDMI • MagicInfo • TV Note • A TV tuner box (sold separately) must be connected to use the TV. (US Only) • MagicInfo can only be enabled when a network box is connected.
Adjusting the LCD Display Recommended for displaying advertisements (e.g. videos or indoor or outdoor ads). 3. Custom Custom By using the on-screen menus, the contrast and brightness can be changed to your personal preference. Note • By adjusting the picture using the Custom function, Mode will change to Custom mode. • Not available when Dynamic Contrast is set to On. 1. Contrast Adjusts the Contrast. 2. Brightness Adjusts the Brightness. 3. Sharpness Adjusts the Sharpness. 4.
Adjusting the LCD Display Color Tone Note Not available when Dynamic Contrast is set to On. The color tones can be changed. 1. Off 2. Cool 3. Normal 4. Warm 5. Custom Note If you set the Color Tone to Cool, Normal, Warm, or Custom, the Color Temp. function is disabled. If you set the Color Tone to Off, the Color Control function is disabled Color Control Adjusts individual Red, Green, Blue color balance. Note Not available when Dynamic Contrast is set to On. 1. Red 2. Green 3.
Adjusting the LCD Display Color Temp. is a measure of the 'warmth' of the image colors. Note This function is enabled when Mode is set to Custom, and Dynamic Contrast and Color Tone are Off. Image Lock Image Lock is used to fine-tune and get the best image by removing noise that creates unstable images with jitters and shakiness. If satisfactory results are not obtained using the Fine adjustment, use the Coarse adjustment and then use Fine again. Note Available in PC mode only.
Adjusting the LCD Display Note • Available in PC mode only. • Not available when Dynamic Contrast is set to On. Signal Balance Selects either On or Off with the signal balance. Signal Control Note Available when Signal Balance is set to On. 1. R-Gain 2. G-Gain 3. B-Gain 4. R-Offset 5. G-Offset 6.
Adjusting the LCD Display Size The Size can be switched. 1. 16:9 2. 4:3 PIP Picture Adjusts the PIP Screen Settings. Note • 1. Available Modes: PIP On Contrast Adjusts the Contrast of the PIP window on the screen. 2. Brightness Adjusts the Brightness of the PIP window on the screen. 3. Sharpness Adjusts the Sharpness of the PIP window on the screen. 4. Color Adjusts the Color of the PIP window on the screen. Note PIP input only operates in AV, HDMI, or Component mode. 5.
Adjusting the LCD Display Note PIP input only operates in AV, HDMI, or Component mode. Dynamic Contrast Dynamic Contrast automatically detects the distribution of the visual signal and adjusts to create an optimum contrast. 1. Off 2. On Note This function is disabled when PIP or Energy Saving is On. Lamp Control Adjusts the inverter lamp in order to reduce energy consumption. Note Not available when Dynamic Contrast is set to On.
Adjusting the LCD Display Picture [ AV / HDMI / Component Mode] Available Modes • PC / DVI / DisplayPort • AV • Component • HDMI • MagicInfo • TV Note • A TV tuner box (sold separately) must be connected to use the TV. (US Only) • MagicInfo can only be enabled when a network box is connected. Mode The LCD Display has four automatic picture settings ("Dynamic", "Standard", "Movie" and "Custom") that are preset at the factory. Dynamic, Standard, Movie, or Custom can be activated.
Adjusting the LCD Display Contrast Adjusts the Contrast. Brightness Adjusts the Brightness. Sharpness Adjusts the picture Sharpness. Color Adjusts the picture Color. Tint Adds a natural tone to the display. Note Operates only if the video signal is NTSC. Color Tone The color tones can be changed. The individual Color components are also user adjustable. Note Not available when Dynamic Contrast is set to On. 1. Off 2. Cool2 3.
Adjusting the LCD Display 4. Normal 5. Warm1 6. Warm2 Note If you set the Color Tone to Cool2, Cool1, Normal, Warm1, or Warm2, the Color Temp. function is disabled. Color Temp. Color temp. is a measure of the 'warmth' of the image colors. Note This function is enabled when Mode is set to Custom, and Dynamic Contrast and Color Tone are Off. Size The Size can be switched.
Adjusting the LCD Display Note • Certain external devices may feed the display an out of spec signal that may cause cutoff even when using the Screen Fit feature. • Zoom 1, Zoom 2 are unavailable in HDMI mode. • The Position and Reset functions are available in Zoom 1 or Zoom 2 modes. Digital NR (Digital Noise Reduction) Turns the Digital Noise Reduction feature Off/On. The Digital Noise Reduction feature allows you to enjoy clearer and crisper images. 1. Off 2.
Adjusting the LCD Display Film Mode Film Mode calibrates unnatural pictures that may occur in a movie (which is in 24 frames). Moving subtitles may appear corrupted when this mode is enabled. (In HDMI mode, this function is available when the input signal is interlaced scan; it is not available in progressive scan.) 1. Off 2. On PIP Picture Adjusts the PIP Screen Settings. Note Available Modes: PIP On 1. Contrast Adjusts the Contrast of the PIP window on the screen. 2.
Adjusting the LCD Display Dynamic Contrast automatically detects the distribution of the visual signal and adjusts to create an optimum contrast. 1. Off 2. On Note This function is disabled when PIP or Energy Saving is On. Lamp Control Adjusts the inverter lamp in order to reduce energy consumption. Note Not available when Dynamic Contrast is set to On. Brightness Sensor Brightness Sensor detects the ambient light intensity so that the picture brightness can automatically be adjusted. 1. Off 2.
Adjusting the LCD Display • TV Note • A TV tuner box (sold separately) must be connected to use the TV. (US Only) • MagicInfo can only be enabled when a network box is connected. Mode The LCD Display has a built-in high fidelity stereo amplifier. 1. Standard Selects Standard for the standard factory settings. 2. Music Selects Music when watching music videos or concerts. 3. Movie Selects Movie when viewing movies. 4. Speech Selects Speech when watching a show that is mostly dialog (i.e.
Adjusting the LCD Display Emphasizes high frequency audio. Balance Allows you to Adjusts the sound balance between the left and right speakers. Auto Volume Reduces the difference in volume control between broadcasters. 1. Off 2. On SRS TS XT SRS TS XT is a patented SRS technology that solves the problem of playing 5.1 multichannel content over two speakers.
Adjusting the LCD Display Note Available when PIP is set to On. 1. Main 2. Sub Speaker Select When you use the product with it connecting to a Home theater, turn the Internal speakers off so you can listen to sound from the Home theater's (external) speakers. 1. Internal Sound is outputted both from the Internal speaker and the External speakers, but the volume control is only available from the Internal speaker. 2.
Adjusting the LCD Display Note • A TV tuner box (sold separately) must be connected to use the TV. (US Only) • MagicInfo can only be enabled when a network box is connected. Language You can choose one of 13 languages. Note The language chosen affects only the language of the OSD. It has no effect on any software running on the computer. Time Clock Set, Sleep Timer, Timer1 / Timer2 / Timer3, and Holiday Management can be set. Clock Set Current Time Setting.
Adjusting the LCD Display 2. 30 3. 60 4. 90 5. 120 6. 150 7. 180 Timer1 / Timer2 / Timer3 You can set the LCD display to automatically turn on or off at a specified time. Note • Hoilday : select Apply to disable the timer on holidays and Don't apply to enable the timer on holidays. • Only enabled when the clock is set using the Clock Set menu. • The Manual option allows you to select a day of the week. Holiday Management • Add You can register holidays.
Adjusting the LCD Display You can delete selected holidays. Note • • Only enabled when registered holidays are selected. • More than one holiday can be selected and deleted. Delete All You can delete all the registered holidays. Menu Transparency Change the transparency of the background of the OSD. 1. High 2. Medium 3. Low 4. Opaque Safety Lock Change PIN The password can be changed. The preset password for the LCD Display is "0000".
Adjusting the LCD Display Note If you forgot your password, press the remote buttons INFO → EXIT → MUTE to reset the password to "0000." Lock On This is the function that locks the OSD in order to keep the current settings or to prevent others from adjusting the settings. Energy Saving This feature adjusts the power consumption of the unit in order to save energy. 1. Off 2.
Adjusting the LCD Display Turns Off/On the Video Wall function of the selected display Off/On. • Off • On Format The Format can be selected to see a divided screen. • Full Provides a full screen without any margins. • Natural Displays a natural image with the original aspect ratio intact. Horizontal Sets how many parts the screen should be divided horizontally. Fifteen adjustment levels: 1~15. Note If Vertical is set to 15, the maximum value for Horizontal is 6.
Adjusting the LCD Display Note If Horizontal is set to 15, the maximum value for Vertical is 6. Screen Position The screen can be divided into several images. A number of screens can be selected with a different layout when dividing. • Select a mode in Screen Position. • Select a display in Display Selection. • The selection will be set up by pressing a number in the selected mode. • The screen can be split into a maximum of 100 sub-screens.
Adjusting the LCD Display Horizontal Sets how many pixels the screen moves horizontally. Five adjustment levels: 0, 1, 2, 3, and 4. Vertical Sets how many pixels the screen moves vertically. Five adjustment levels: 0, 1, 2, 3, and 4. Time Set the time interval for performing the horizontal or vertical movement, respectively. Timer Timer You can set the timer for Screen Burn Protection.
Adjusting the LCD Display • Off • On Mode You can change the Safety Screen Type. • Bar • Eraser • Pixel Period Use this function to set the execution period for each mode set in the timer. Time Within the set period of time specify a time for execution.
Adjusting the LCD Display This function prevents after-images on the screen by moving long black and white vertical lines. Eraser This function prevents after-images on the screen by moving a rectangular pattern. Pixel This function prevents after-images by moving many pixels on the screen. Side Gray Select the brightness of the grey for the screen background.
Adjusting the LCD Display When the picture is not displayed properly on the screen when setting the graphics card resolution of the computer to 1024 x 768 @ 60Hz, 1280 x 768 @ 60Hz, 1360 x 768@ 60Hz or 1366 x 768 @ 60Hz, by using this function(Resolution Select), you can have the picture displayed on the screen in the specified resolution. Note Available in PC mode only. 1. Off 2. 1024 X 768 3. 1280 X 768 4. 1360 x 768 5.
Adjusting the LCD Display Advanced Settings Configures the settings more elaborately. Temperature Protects the product by detecting the internal temperature. Temperature Control Detects the product's internal temperature and specifies the desired temperature. The product is set to 77°C by default. Note • The picture will be dimmed if the temperature exceeds the specified temperature, and the product ill automatically power off to prevent overheating if the temperature keeps rising.
Adjusting the LCD Display • Off • On Note When Auto Power is On, the product will power on automatically as soon as it is connected to power. Button Lock Locks or unlocks the monitor control buttons on the product. • Off • On User Auto Color 1. Auto Color Automatically adjusts the colors. 2. Reset Resets the color settings. Note Enabled only in PC mode.
Adjusting the LCD Display Sets the standby mode, which will be activated when no input signal is detected. • Off A message will read if no input signal is detected. • On Power-saving mode will be activated if no input signal is detected. • Auto When no input signal is detected, - Power-saving mode will be activated if an external device is connected. - A message will read if no external device is connected. Note • Enabled only in PC, DVI, HDMI, or DP(DisplayPort) mode.
Adjusting the LCD Display Not Optimum Mode OSD • Off • On No Signal OSD • Off • On MDC OSD • Off • On Software Upgrade Performs a software upgrade. 1. Connect the product to a computer via a digital signal such as DVI or HDMI. Click the BMP image file converted from an SW code. The image below will appear on the screen of the product. 2. While a BMP image onto which the software code has been converted is displayed on the screen, select Software Upgrade.
Adjusting the LCD Display Note When there are two or more BMP images, they are displayed on the screen using a slideshow. • It is recommended that the playback interval between two BMP images in the slideshow should be one second. The image extraction probability will decrease with other playback intervals. • A BMP image might not be extracted if it is covered by another image (for example, the mouse pointer). 3.
Adjusting the LCD Display Reset all the settings for the display. Multi Control Available Modes • PC / DVI / DisplayPort • AV • Component • HDMI • MagicInfo • TV Note • A TV tuner box (sold separately) must be connected to use the TV. (US Only) • MagicInfo can only be enabled when a network box is connected. Multi Control Assigns an individual ID to the SET. • ID Setup Assigns distinctive IDs to the SET. • ID Input Use to select the transmitter functions of the individual SET.
Adjusting the LCD Display • Subnet Mask : Manually enter the Subnet Mask if IP Setting is set to Manual. • Gateway : Manually enter the Gateway if IP Setting is set to Manual. MagicInfo Available Modes • PC / DVI / DisplayPort • AV • Component • HDMI • MagicInfo • TV Note • MagicInfo can only be enabled when a network box is connected. • The remote control can be used to select MagicInfo. However, it is recommended to use a separate USB keyboard to utilize MagicInfo fully.
Adjusting the LCD Display • To setup MagicInfo on a Windows screen, a keyboard and mouse are required. • To setup MagicInfo on a Windows screen, refer to the MagicInfo Server Help. It is highly recommended not to turn off the AC power during an operation. • For pivoted LCD Displays, ticker transparency is not supported. • For pivoted LCD Displays, a screen resolution of up to 720*480(SD) is supported for movies. • For drive D:, EWF is not applied.
Adjusting the LCD Display In step 2 of MagicInfo Setup Wizard, you don’t have to go to Network Setting on the desktop to make your settings for TCP/IP. You just do that at step 2 of MagicInfo installation. 3. Select Language - step 3 When using multiple languages, you can choose and set a specific language among them. 4.
Adjusting the LCD Display You can select which rotation type will be applied to your device. 5. Setup Information Shows the settings that have been selected by the user. Note If the MagicInfo icon is not displayed on the notification area, double click the MagicInfo icon on the window desktop. The icon will appear.
Troubleshooting Self-Test Feature Check Note Check the following items yourself before calling for assistance. Contact a Service Center for problems that you cannot solve by yourself. Self-Test Feature Check 1. Turn off both your computer and the LCD Display. 2. Unplug the video cable from the back of the computer. 3. Turn on the LCD Display.
Troubleshooting • Do not use benzene, thinner or other flammable substances. 2) Maintaining the Flat Panel Display Screen. Clean with a soft cloth (cotton flannel). • Never use acetone, benzene or thinner. (They may cause flaws or deformation of the screen surface.) • The user is responsible for any damage caused by using these substances. Symptoms and Recommended Actions Note A LCD Display recreates visual signals received from the computer.
Troubleshooting A: Check if the signal cable between the computer and the LCD Display is securely connected. (Refer to Connecting a Computer) Problems related to the Screen Note Problems related to the LCD Display screen and their solutions are listed. Q: The screen is blank and the power indicator is off. A: Ensure that the power cord is firmly connected and the LCD Display is on. (Refer to the Connecting a Computer) Q: "No Signal" message.
Troubleshooting Q: The screen color is inconsistent. A: Adjust color using Custom under OSD Color Adjustment menu. Q: The color image is distorted by dark shadows. A: Adjust color using Custom under OSD Color Adjustment menu. Q: The color white is poor. A: Adjust color using Custom under OSD Color Adjustment menu. Q: The Power Indicator blinks. A: The LCD Display is currently saving the changes made in the settings to the OSD memory.
Troubleshooting A: Check if a special fluorescent or neon lamp is on in the vicinity. Q: How can I change the frequency? A: The frequency can be changed by reconfiguring the video card. Q&A Note That video card support can vary, depending on the version of the driver used. (Refer to the computer or the video card manual for details.) Q: How can I adjust the resolution? A: Windows XP: Control Panel → Appearance and Themes → Display → Settings.
Specifications General General Model Name SyncMaster 400DX-3 / 460DX-3 LCD Panel Size Display area 400DX-3 40 inches (101 cm) 460DX-3 46 inches (116 cm) 400DX-3 885.6 mm (H) x 498.15 mm (V) 460DX-3 1018.08 mm (H) x 572.67 mm (V) Synchronization Horizontal 30 ~ 81 kHz Vertical 56 ~ 85 Hz Display Color 16.7 M (true) Resolution Optimum resolution 1920 x 1080 @ 60 Hz Maximum resolution 1920 x 1080 @ 60 Hz Maximum Pixel Clock 148.
Specifications Dimensions (W x H x D) Without Stand 1068.0 x 620.5 x 130.0 mm / 42.1 x 24.4 x 5.1 inches 1068.0 x 620.5 x 136.0 mm / 42.1 x 24.4 x 5.4 inches (With protection glass-option) Weight With Box Network 400DX-3 19.3 Kg / 42.9 lbs 23.0 Kg / 50.7 lbs (With protection glass-option) Without Network Box 17.0 Kg / 37.5 lbs 20.7 Kg / 45.6 lbs (With protection glass-option) With Box Network 460DX-3 23.5 Kg / 51.8 lbs 27.5 Kg / 60.6 lbs (With protection glass-option) Without Network Box 21.
Specifications Dot Acceptable For example, the number of TFT-LCD sub pixels contained in this product are 6,220,800. Note Design and specifications are subject to change without prior notice. When the network box is connected Class A (Information Communication equipment for industrial use) Attention dealers and users. This device is registered for EMC requirements for industrial use (Class A) and can be used in areas other than general households.
Specifications State Normal Opera- Power saving tion mode Power off Power off (Power Swich) Power Indicator On (Green) Blinking Amber Off Power Consumption 300 Watts 5 Watts 5 Watts 0 Watts (1023 BTU/h) (17.05 BTU/h) (17.05 BTU/h) (0 BTU/h) (With Network Box) Power Consumption 230 Watts 2 Watts 1 Watts 0 Watts (784.3 BTU/h) (6.28 BTU/h) (3.
Specifications Display Mode Horizontal Vertical Fre- Pixel Clock Sync Polarity Frequency quency (Hz) (MHz) (H/V) (kHz) VESA, 1024 x 768 56.476 70.069 75.000 -/- VESA, 1024 x 768 60.023 75.029 78.750 +/+ VESA, 1152 x 864 67.500 75.000 108.000 +/+ VESA, 1280 x 768 47.776 59.870 79.500 -/+ VESA, 1280 x 960 60.000 60.000 108.000 +/+ VESA, 1280 x 1024 63.981 60.020 108.000 +/+ VESA, 1280 x 1024 79.976 75.025 135.000 +/+ VESA, 1360 x 768 47.712 60.015 85.
Information For a Better Display Adjust the computer resolution and screen injection rate (refresh rate) on the computer as described below to enjoy the best picture quality. You can have an uneven picture quality on screen if the best picture quality is not provided for TFTLCD. • Resolution: 1920 x 1080 • Vertical frequency (refresh rate): 60 Hz TFT-LCD panels manufactured by using advanced semiconductor technology with a precision of 1ppm (one millionth) and above is used for this product.
Information Power Off, Screen Saver, or Power Save Mode • Turn the power off for 4 hours after 20 hours in use • Turn the power off for 2 hours after 12 hours in use • Set the Monitor to power off with the PC Display Properties Power Scheme. • Use a Screen saver if possible - Screen saver in one color or a moving image is recommended. Change the Color Information periodically Note Use Two different colors Rotate the Color Information with 2 different colors every 30 minutes.
Information • Avoid using a combination of characters and background color with large difference in luminance. Avoid using Grey colors, which can cause Image retention easily. Avoid: Colors with big difference in luminance (Black & White, Grey) Change the characters color periodically • Use Bright colors with little difference in luminance. - Cycle : Change the characters color and background color every 30 minutes • Every 30 minutes, change the characters with movement.
Information • Apply the Screen Bar function - Symptom: Horizontal / Vertical Bar with Black Color move up and down.
Appendix Contact SAMSUNG WORLDWIDE Note If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center. North America U.S.A 1-800-SAMSUNG (726-7864) http://www.samsung.com CANADA 1-800-SAMSUNG (726-7864) http://www.samsung.com/ca http://www.samsung.com/ ca_fr (French) MEXICO 01-800-SAMSUNG (726-7864) http://www.samsung.com Latin America ARGENTINA 0800-333-3733 http://www.samsung.com BRAZIL 0800-124-421 http://www.samsung.
Appendix Europe http://www.samsung.com/ be_fr (French) BOSNIA 05 133 1999 http://www.samsung.com BULGARIA 07001 33 11 http://www.samsung.com CROATIA 062 SAMSUNG (062 726 http://www.samsung.com 7864) CZECH 800 (800-726786) DENMARK 70 70 19 70 http://www.samsung.com FINLAND 030 - 6227 515 http://www.samsung.com FRANCE 01 48 63 00 00 http://www.samsung.com GERMANY 01805 SAMSUNG http://www.samsung.
Appendix Europe SWITZERLAND 0848 - SAMSUNG (7267864, http://www.samsung.com/ch CHF 0.08/min) http://www.samsung.com/ ch_fr/(French) U.K 0330 SAMSUNG (7267864) http://www.samsung.com EIRE 0818 717100 http://www.samsung.com LITHUANIA 8-800-77777 http://www.samsung.com LATVIA 8000-7267 http://www.samsung.com ESTONIA 800-7267 http://www.samsung.com TURKEY 444 77 11 http://www.samsung.com CIS RUSSIA 8-800-555-55-55 http://www.samsung.com GEORGIA 8-800-555-555 http://www.samsung.
Appendix Asia Pacific JAPAN 0120-327-527 http://www.samsung.com MALAYSIA 1800-88-9999 http://www.samsung.com PHILIPPINES 1-800-10-SAMSUNG (726-7864) for PLDT http://www.samsung.com 1-800-3-SAMSUNG (726-7864) for Digitel 1-800-8-SAMSUNG (726-7864) for Globe 02-5805777 SINGAPORE 1800-SAMSUNG (726-7864) http://www.samsung.com THAILAND 1800-29-3232 http://www.samsung.com 02-689-3232 TAIWAN 0800-329-999 http://www.samsung.com 0266-026-066 VIETNAM 1 800 588 889 http://www.samsung.
Appendix tance between two dots of the same color is called the 'Dot Pitch'. Unit: mm Vertical Frequency The screen must be redrawn several times per second in order to create and display an image for the user. The frequency of this repetition per second is called the Vertical Frequency or Refresh Rate. Unit: Hz Example: If the same light repeats itself 60 times per second, this is regarded as 60 Hz.
Appendix Correct Disposal Correct Disposal of This Product (Waste Electrical & Electronic Equipment) (Applicable in the European Union and other European countries with separate collection systems) This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset, USB cable) should not be disposed of with other household waste at the end of their working life.
Appendix Authority Information in this document is subject to change without notice. © 2010 Samsung Electronics Co., Ltd. All rights reserved. Reproduction in any manner whatsoever without the written permission of Samsung Electronics Co., Ltd. is strictly forbidden. Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.
