User Manual ME40A ME46A ME55A DE40A DE46A DE55A UE46A UE55A The color and the appearance may differ depending on the product, and the specifications are subject to change without prior notice to improve the performance.
Before Using the Product Copyright The contents of this manual are subject to change without notice to improve quality. 2011 Samsung Electronics Samsung Electronics owns the copyright for this manual. Use or reproduction of this manual in parts or entirety without the authorization of Samsung Electronics is prohibited. The SAMSUNG and SyncMaster logos are registered trademarks of Samsung Electronics. Microsoft, Windows and Windows NT are registered trademarks of Microsoft Corporation.
Before Using the Product Cleaning Exercise care when cleaning as the panel and exterior of advanced LCDs are easily scratched. Take the following steps when cleaning. The following images are for reference only. Real-life situations may differ from what is shown in the images. 1. Power off the product and computer. 2. Disconnect the power cord from the product. Hold the power cable by the plug and do not touch the cable with wet hands. Otherwise, an electric shock may result. 3.
Before Using the Product Safety Precautions Caution RISK OF ELECTRIC SHOCK DO NOT OPEN Caution : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). THERE ARE NO USER SERVICEABLE PARTS INSIDE. REFER ALL SERVICING TO QUALIFIED PERSONNEL. This symbol indicates that high voltage is present inside. It is dangerous to make any kind of contact with any internal part of this product.
Before Using the Product Electricity and Safety The following images are for reference only. Real-life situations may differ from what is shown in the images. Warning Do not use a damaged power cord or plug, or a loose power socket. An electric shock or fire may result. Do not use multiple products with a single power socket. Overheated power sockets may cause a fire. Do not touch the power plug with wet hands. Otherwise, an electric shock may result.
Before Using the Product Caution Do not disconnect the power cord while the product is being used. The product may become damaged by an electric shock. Only use the power cord provided with your product by Samsung. Do not use the power cord with other products. ! A fire or electric shock may result. Keep the power socket where the power cord is connected unobstructed. The power cord must be disconnected to cut off power to the product when an issue occurs.
Before Using the Product Keep the plastic packaging out of the reach of children. Children may suffocate. ! Do not install the product on an unstable or vibrating surface (insecure shelf, sloped surface, etc.) The product may fall and become damaged and/or cause an injury. Using the product in an area with excess vibration may damage the product or cause a fire. Do not install the product in a vehicle or a place exposed to dust, moisture (water drips, etc.), oil, or smoke.
Before Using the Product Set down the product gently Product failure or personal injury may result. ! SAMSUNG ! Installing the product in an unusual place (a place exposed to a lot of fine particles, chemical substances or extreme temperatures, or an airport or train station where the product should operate continuously for an extended period of time) may seriously affect its performance. Be sure to consult Samsung Customer Service Center if you want to install the product at such a place.
Before Using the Product During a lightning or thunderstorm, remove the power cord and do not touch the antenna cable. ! A fire or electric shock may result. Do not drop objects on the product or apply impact. A fire or electric shock may result. ! Do not move the product by pulling the power cord or any cable. Product failure, an electric shock or fire may result from a damaged cable. If a gas leakage is found, do not touch the product or power plug. Also, ventilate the area immediately.
Before Using the Product 100 Do not insert metallic objects (chopsticks, coins, hairpins, etc) or objects that burn easily (paper, matches, etc) into the product (via the vent or input/output ports, etc). Be sure to power off the product and disconnect the power cord when water or other foreign substances have entered the product. Then contact Samsung Customer Service Center. Product failure, an electric shock or fire may result.
Before Using the Product Do not use humidifiers or stoves around the product. A fire or electric shock may result. Rest your eyes for more than 5 minutes for every 1 hour of product use. Eye fatigue will be relieved. ! Do not touch the screen when the product has been turned on for an extended period of time as it will become hot. Store small accessories out of the reach of children. ! Exercise caution when adjusting the product angle or stand height.
Table Of Contents BEFORE USING THE PRODUCT PREPARATIONS CONNECTING AND USING A SOURCE DEVICE 2 Copyright 3 Cleaning 3 Storage 4 Safety Precautions 4 5 6 8 Symbols Electricity and Safety Installation Operation 21 Checking the Contents 21 22 Removing the Packaging Checking the Components 24 Parts 24 25 27 28 Control Panel Reverse Side Anti-theft Lock Remote Control 31 Before Installing the Product (Installation Guide) 31 32 34 Tilting Angle and Rotation Ventilation Dimensions 35 Ins
Table Of Contents USING MDC 51 Connecting and Using a PC 51 54 Connecting to a PC Changing the Resolution 56 Connecting to a Video Device 56 56 57 58 59 59 Connection Using the AV Cable Connection Using the component Cable Connection Using an HDMI-DVI Cable Connection Using an HDMI Cable Connecting an External Monitor Connecting to an Audio System 60 Changing the Input source 60 Source 61 Connecting the network box 61 MagicInfo 65 Configuring Settings for Multi Control 65 Configuring se
Table Of Contents SCREEN ADJUSTMENT 68 What is MDC? 68 69 70 71 72 73 75 76 78 82 83 91 93 98 Connecting to MDC Connection Management Auto Set ID Cloning Command Retry Getting Started with MDC Main Screen Layout Menus Screen Adjustment Sound Adjustment System Setup Tool Settings Other Functions Troubleshooting Guide 100 Picture Mode 100 100 If the input source is PC, DVI or DP If the input source is AV, Component, HDMI 101 Backlight / Contrast / Brightness / Sharpness / Colo(u)r / Tint(G/R) 101
Table Of Contents SOUND ADJUSTMENT MEDIA 107 Advanced Settings 107 108 108 108 108 108 108 109 109 109 109 109 109 Black Tone Dynamic Contrast Shadow Detail Gamma Expert Pattern RGB Only Mode Colo(u)r Space White Balance 10p White Balance (Off / On) Flesh Tone Edge Enhancement (Off / On) Motion Lighting (Off / On) LED Motion Plus (Off / On) 110 Picture Options 110 110 110 111 111 111 111 Colo(u)r Tone Colo(u)r Temp.
Table Of Contents NETWORK SYSTEM 117 Videos 117 Playing a Video 121 Photos 121 Viewing a Photo (or Slide Show) 122 Music 122 Playing Music 124 Videos / Photos / Music - Additional Functions 124 125 Sorting the file lists Videos/Photos/Music Play Option menu 127 Source 127 127 128 128 Source Edit Name Information Refresh 129 AllShare 130 Network Settings 130 131 133 134 136 136 137 Connecting to a Wired Network Wired Network Settings Connecting to a Wireless Network Wireless Netwo
Table Of Contents 142 Time 142 142 142 143 143 Clock set Sleep Timer On Timer Off Timer Holiday Management 144 Menu Language 145 Eco Solution 145 145 146 146 Energy Saving Eco Sensor (Off / On) No Signal Power Off Auto Power Off (Off / On) 146 Security 146 146 147 Safety Lock (Off / On) Button Lock (Off / On) Change PIN 147 PIP 148 Auto Protection Time 149 Screen Burn Protection 149 149 150 150 Pixel Shift Timer Pixel Side Gray 151 Video Wall 151 151 151 152 152 Video Wall Format H
Table Of Contents SUPPORT MAGICINFO LITE 154 General 154 154 155 155 155 155 155 156 156 156 Max.
Table Of Contents TROUBLESHOOTING GUIDE SPECIFICATIONS 174 Local Schedule 174 Local Schedule Manager 174 177 178 180 181 182 Registering a Local Schedule Modifying a local schedule Local Schedule Deleting a local schedule Local Schedule Running a local schedule Local Schedule Stopping a local schedule Local Schedule Viewing the details of a local schedule Local Schedule 183 Contents Manager 183 184 Copying content Deleting content 185 Internal AutoPlay 185 Running Internal AutoPlay 185 USB
Table Of Contents APPENDIX 200 Contact SAMSUNG WORLDWIDE 206 Optimum Picture Quality and Afterimage Burn-in Prevention 206 207 Optimum Picture Quality Prevention of Afterimage Burn-in 210 Correct Disposal of This Product (Waste Electrical & Electronic Equipment) Europe only 210 Correct disposal of batteries in this product - Europe only 211 Terminology INDEX Table Of Contents 20
1 Checking the Contents 1.1.1 Removing the Packaging 1 Remove the black locking device at the bottom of the box. 1 2 2 Using the grooves in the box, lift and remove the top of the box. 3 Check the components and remove the styrofoam and plastic bag.
1.1.2 Checking the Components Contact the vendor where you purchased the product if any components are missing. The appearance of the components and items sold separately may differ from the image shown. Components Components may differ in different locations.
1 Preparations Items sold separately The stand is not supplied. The following items can be purchased at your nearest retailer.
1 1.2 Preparations Parts 1.2.1 Control Panel The color and shape of parts may differ from what is shown. Specifications are subject to change without notice to improve quality. Keep the area between the remote sensor and remote control obstacle-free. SOURCE MENU + - POWER POWER Sensor SOURCE MENU + - Description Selects the input source that an external device is connected to. Opens the on-screen menu and exits from the menu.
1 Preparations Sensor Description Use this button for turning the Display on and off. Receives signals from the remote To control the remote control in front of the product, lower the remote control sensor in the direction of the arrow (indicated in the zoomed-in image on the previous page). Remote sensor Keep the area between the remote sensor and remote control obstacle-free. 1.2.2 Reverse Side The color and shape of parts may differ from what is shown.
1 Preparations Port [RGB / DVI / DP / HDMI AUDIO IN] [USB] [AV IN / COMPONENT IN] [DP IN] [HDMI IN] [DVI OUT (LOOPOUT)] Description Receives sound from a PC via an audio cable. Connect to a USB memory device. Connects to a source device using the AV/component adapter. Connects to a PC using a DP cable. Connects to a source device using an HDMI cable. Connects to another product using a DVI cable. [DVI IN] Connects to a source device using a DVI cable or HDMI-DVI cable.
1 Preparations Assembling the Holder-Wire stand * Stand : Sold separately 1.2.3 Anti-theft Lock An anti-theft lock allows you to use the product securely even in public places. The locking device shape and locking method depend on the manufacturer. Refer to the user guide provided with your anti-theft locking device for details. To lock an anti-theft locking device: 1 Fix the cable of your anti-theft locking device to a heavy object such as a desk.
1 Preparations 1.2.4 Remote Control Using other display devices in the same space as the remote control of this product can cause the other display devices to be inadvertently controlled. Remote control button functions may differ for different products. This is a special remote control for the visually impaired persons and has Braille points on the Power, Channel and Volume buttons. POWER OFF OFF Power on the product. Power off the product. SOURCE Change the input source. Not available.
1 Preparations Adjusting the OSD with the Remote Control MENU EXIT 1. Open the OSD menu. 2. Select from Picture, Sound, Media, Network, System or Support in the displayed OSD menu screen. 3. Change settings as desired. 4. Finish setting. 5. Close the onscreen display (OSD) menu.
Remote Control Reception Range 7m ~ 10m 1 Preparations OFF Use the remote control within 7m to 10m from the sensor on the product at an angle of 30 from the left and right. Store used batteries out of reach of children and recycle. Do not use a new and used battery together. Replace both batteries at the same time. Remove batteries when the remote control is not to be used for an extended period of time.
1 1.3 Preparations Before Installing the Product (Installation Guide) To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation instructions. Ensure that an authorized installation company installs the wall mount. Otherwise, it may fall and cause personal injury. Make sure to install the specified wall mount. 1.3.1 Tilting Angle and Rotation Contact Samsung Customer Service Center for further details.
1 Preparations 1.3.2 Ventilation 1. Installation on a Perpendicular Wall A Minimum 40 mm B Ambient temperature: Under 35 C When installing the product on a perpendicular wall, allow at least 40mm of space between the product and wall surface for ventilation and ensure that the ambient A temperature is kept below 35 C. B Figure 1.
1 Preparations 2. Installation on an Indented Wall Contact Samsung Customer Service Center for further details. B D D Plane view A A Minimum 40 mm B Minimum 70 mm C Minimum 50 mm C D Minimum 50 mm E E Ambient temperature: Under 35 C Figure 1.2 Side view When installing the product on an indented wall, allow at least the space specified above between the product and wall for ventilation and ensure that the ambient temperature is kept below 35 C. 3.
1 Preparations 1.3.3 Dimensions 1 5 4 2 3 (Unit: mm) SET - Dimension (W x D x H) [mm] Without STAND Model name 1 2 3 4 5 ME40A / DE40A 920.0 885.6 498.2 534.5 29.9 ME46A / DE46A 1055.2 1018.0 572.6 610.8 29.9 ME55A / DE55A 1246.4 1209.6 680.4 718.2 29.9 UE46A 1030.4 1020.1 574.6 585.0 29.9 UE55A 1221.8 1211.6 682.4 692.7 29.9 All drawings are not necessarily to scale. Some dimensions are subject to change without prior notice.
1 1.4 Preparations Installing the Wall Mount 1.4.1 Preparing before installing Wall-Mount To install a wall-mount from another manufacturer, use the Holder-Ring. 1 1.4.2 Installing the Wall Mount Kit The wall mount kit (sold separately) allows you to mount the product on the wall. For detailed information on installing the wall mount, see the instructions provided with the wall mount. We recommend you contact a technician for assistance when installing the wall mount bracket.
1 Preparations Standard dimensions for wall mount kits are shown in the table below. Samsung wall mount kits contain a detailed installation manual and all parts necessary for assembly are provided. Do not use screws that do not comply with the VESA standard screw specifications. Do not use screws that are longer than the standard length or do not comply with the VESA standard screw specifications. Screws that are too long may cause damage to the inside of the product.
1 1.5 Preparations Remote Control (RS232C) 1.5.1 Cable Connection Interface Pin TxD (No. 2), RxD (No. 3), GND (No.
1 Preparations RS232C cable Connector: 9-Pin D-Sub to Stereo Cable 9 6 3 2 1 5 -P2STEREO PLUG (3.5ø) 1 -P1- -P1- -P1- -P2- Rx 2 --------> 1 Tx Tx 3 <-------- 2 Rx Gnd 5 --------- 3 Gnd Female -P2- STEREO PLUG (3.
1 Preparations 1.5.2 Control Codes Viewing control state (Get control command) Header Command 0xAA Command type Data length ID Checksum 0 Controlling (Set control command) Header Command 0xAA Command type Data length Data 1 Value ID Checksum Command No.
1 Preparations To control all devices connected by a serial cable simultaneously irrespective of IDs, set the ID as "0xFE" and transmit commands. Commands will be executed by each device but ACK will not respond. Power control Function A product can be powered on and off using a PC.
1 Preparations Volume control Function The volume of a product can be adjusted using a PC.
1 Preparations Input source control Function The input source of a product can be changed using a PC.
1 Preparations Header Comma nd Data length Ack/Nak r-CMD Val1 ID 0xAA 0xFF 3 ‘A’ 0x14 "Input Source" Checksu m "Input Source": An input source code to be set on a product Nak Header 0xAA Comma nd 0xFF Data length Ack/Nak r-CMD Val1 3 ‘N’ 0x14 "ERR" ID Checksu m "ERR" : A code showing what error has occurred 1 Preparations 43
1 Preparations Screen Function The screen mode of a product can be changed using a PC. Screen mode cannot be controlled when the Video Wall function is enabled. This control can only be used on models that include a product.
1 Preparations Screen size control Function The screen size of a product can be changed using a PC.
1 Preparations PIP On/Off control Function The PIP mode of a product can be turned on or off using a PC. Only available on models that have the PIP function The mode cannot be controlled if Video Wall is set to On. This function is not available in MagicInfo.
1 Preparations Auto adjustment control (PC and BNC only) Function Automatically adjust the PC system screen using a PC.
1 Preparations Video Wall Mode Control Function Video Wall Mode can be activated on a product using a PC. This control is only available on a product whose Video Wall is enabled. This function is not available in MagicInfo.
1 Preparations Safety Lock Function PC can be used to turn the Safety Lock function on or off on a product. This control is available regardless of whether or not the power is turned on.
2 2.1 Connecting and Using a Source Device Before Connecting Check the following before you connect this product with other devices. Devices that can be connected to this product include PCs, camcorders, speakers, set top boxes and DVD/Blu-ray Disc players. Audio 2.1.1 Pre-connection Checkpoints Before connecting a source device, read the user manual provided with it. The number and locations of ports on source devices may differ from device to device.
2 2.2 Connecting and Using a Source Device Connecting and Using a PC 2.2.1 Connecting to a PC A PC can be connected to the product in a variety of ways. Select a connection method suitable for your PC. After connecting the PC, connect the power cable. Connecting parts may differ in different products.
2 Connecting and Using a Source Device Connection Using an HDMI-DVI Cable HDMI IN RGB / DVI / DP / HDMI AUDIO IN When you connect a PC to the product using an HDMI-DVI cable, set Edit Name to DVI PC to access video and audio content stored on the PC.
2 Connecting and Using a Source Device Connection Using an DP Cable DP IN 2 Connecting and Using a Source Device 53
2 Connecting and Using a Source Device 2.2.2 Changing the Resolution Adjust the resolution and refresh rate in Control Panel on your PC to obtain optimum picture quality. The picture quality of TFT-LCDs may degrade if the optimum resolution is not selected. Changing the Resolution on Windows XP Go to Control Panel 1 Display Settings, and change the resolution.
2 Connecting and Using a Source Device Changing the Resolution on Windows 7 Go to Control Panel Display Screen Resolution, and change the resolution.
2 2.3 Connecting and Using a Source Device Connecting to a Video Device You can connect a video device to the product using a cable. Connecting parts may differ in different products. Press the SOURCE button on the remote control to change the source. 2.3.1 Connection Using the AV Cable AV IN AV OUT 2.3.
2 Connecting and Using a Source Device 2.3.3 Connection Using an HDMI-DVI Cable HDMI RGB / DVI / DP / HDMI AUDIO IN Audio will not be enabled if the product is connected to a video device using an HDMI-DVI cable. To resolve this, additionally connect an audio cable to the audio ports on the product and video device. Supported resolutions include 1080p (50/60Hz), 720p (50/60Hz), 480p, and 576p.
2 Connecting and Using a Source Device 2.3.4 Connection Using an HDMI Cable HDMI IN Using an HDMI cable or HDMI to DVI Cable (up to 1080p) For better picture and audio quality, connect to a digital device using an HDMI cable. An HDMI cable supports digital video and audio signals, and does not require an audio cable. To connect the product to a digital device that does not support HDMI output, use an HDMI/ DVI and audio cables.
2 Connecting and Using a Source Device 2.3.5 Connecting an External Monitor DVI OUT (LOOPOUT) AUDIO OUT The following images are for reference only. Real-life situations may differ from what is shown in the images. The Loopout function can be used to duplicate the screen of the primary display. Connect [DVI OUT] on the primary display to [DVI IN] or [HDMI] on another display. Up to HD resolution can be supported. Compatible input sources include DVI IN, DP IN and HDMI IN.
2 2.4 Connecting and Using a Source Device Changing the Input source 2.4.1 Source O MENU m Media Source ENTER Source allows you to select a variety of sources and change source device names. Source You can display the screen of a source device connected to the product. Select a source from source list to display the screen of the selected source. Refer to page 127 for details about the Source menu.
2 2.5 Connecting and Using a Source Device Connecting the network box For details on how to connect to a network box, refer to the user's manual provided with the network box upon purchase. 2.5.1 MagicInfo To use MagicInfo, a network box (sold separately) must be connected to the product. To change the MagicInfo settings, run "MagicinfoSetupWizard" on the desktop. For details on how to use MagicInfo, refer to the DVD provided with the network box.
2 Connecting and Using a Source Device 3 Select the default application you want to run when MagicInfo starts. MagicInfo Setup Wizard - v.1.12 Select Application - step 1 MagicInfo Pro (LAN, WAN based version) MagicInfo-i Premium (Web-based version) Select Later < Back(B) 4 Next(N) > Finish Cancel Enter the IP information. MagicInfo Setup Wizard - v.1.12 Select TCP/IP - step 2 Obtain an IP address automatically Use the following IP address: IP address: 192 . 168 . 0 .
2 Connecting and Using a Source Device 5 Select a language. (The default language is English.) MagicInfo Setup Wizard - v.1.12 Select Language -step 3 Select the language you want to install on the system for menus and dialogs. Current Language : Engilsh Chinese [Traditional] German English French Italian Japanese Korean Russian Swedish Turkish Chinese [Simplified] Portuguese < Back(B) 6 Next(N) > Finish Cancel Select a display mode. MagicInfo Setup Wizard - v.1.
2 Connecting and Using a Source Device 7 Double-check the settings you have just configured. MagicInfo Setup Wizard - v.1.12 Setup Information 1. Application : MagicInfo Pro [LAN,WAN based version\ 2. Internet Protocol [TCP/IP] IP : 192.168.0.102 3. Language : 4. Screen Type : English Landscape Do not show again < Back(B) Apply Finish Cancel If the execution icon does not appear, double-click the MagicInfo icon on the desktop. The icon will appear at the bottom right of the screen.
3 Using MDC MDC (Multiple Display Control) is an application that allows you to easily control multiple display devices simultaneously using a PC. 3.1 Configuring Settings for Multi Control O MENU m System Multi Control ENTER Assign an individual ID to your product. 3.1.1 Configuring settings for Multi Control MDC Connection Selects a port to receive the MDC inputs from. RS232C MDC Communicates with the MDC via a RS232C MDC cable. RJ45 MDC Communicates with the MDC via an RJ45 MDC cable.
3 3.3 Using MDC Communicate with LAN cable RJ45 Multiple products can be connected using the [RJ45] port on the product and the LAN ports on the HUB. 3.4 Communicate with Stereo cable via the LAN cable RS232C OUT RJ45 Multiple products can be connected using the [RS232C IN / OUT] port on the product.
3 3.5 Using MDC MDC Program Installation/Uninstallation 3.5.1 Installation 1 2 Insert the installation CD into the CD-ROM drive. Click the MDC Unified installation program. If a software installation window is not displayed on the main screen, install with the "MDC Unified" execution file in the MDC folder on the CD. 3 4 Click "Next" in the displayed Installation Wizard screen. In the "License Agreement" window displayed, select "I accept the terms in the license agreement" and click "Next".
3 3.6 Using MDC What is MDC? Multiple display control "MDC" is an application that allows you to easily control multiple display devices simultaneously using a PC. 3.6.1 Connecting to MDC Using MDC via RS-232C (serial data communications standards) An RS-232C serial cable must be connected to the serial ports on the PC and monitor. Using MDC via Ethernet Enter the IP for the primary display device and connect the device to the PC. One display device can connect to another using an RS-232C serial cable.
3 Using MDC 3.6.2 Connection Management Connection management includes the Connection list and Connection list modification options. Connection list – Connection list shows the details of the connections such as connection setting (IP/ COM, Port No, MAC, and Connection Type), connection status, Set ID Range, and detected devices. Each connection can contain a maximum of 100 devices connected in serial daisy-chain fashion.
3 Using MDC 3.6.3 Auto Set ID Auto Set ID feature assigns a Set ID for all the LFDs connected in daisy-chain of a selected connection. There can be a maximum of 100 LFDs in a connection. The Set ID is assigned sequentially in the daisychain running from 1 to 99, and then finally to Set ID 0.
3 Using MDC 3.6.4 Cloning Using the Cloning feature, you can copy the setting of one LFD and apply it to multiple selected LFDs. You can select specific tab categories or all tab categories for cloning, using the copy setting option window.
3 Using MDC 3.6.5 Command Retry This feature is used to specify the maximum number of times the MDC command will be retried in case of there being no reply or a corrupted reply from an LFD. The retry count value can be set using the MDC options window. The retry count value must be between 1-10. The default value is 1.
3 Using MDC 3.6.6 Getting Started with MDC 1 To start the program, click Start 2 Click Add to add a display device. Programs Samsung MDC Unified. If the connection is established via RS232C, go to Serial and specify the COM Port.
3 Using MDC If the connection is established via Ethernet, enter the IP that was entered for the display device.
3 Using MDC 3.6.7 Main Screen Layout 1 6 5 4 2 3 1 Menu Bar Change the status of a display device or the properties of the program. 2 Device Category View a list of connected display devices or device groups. 3 Schedule Category View a list of schedules for display devices. 4 Set List Select the display device you want to adjust. 5 Modify the Set List Add, edit, regroup or delete sets. 6 Help Topics Display help topics for the program.
3 Using MDC 3.6.8 Menus You can power on or off a selected device or change the input source or volume of the device. Choose display devices from the list of sets, and select the Home tab. 1 Home Select an item and change the corresponding setting. Power On: Power on a selected display. Off: Power off a selected dis Input Input Source : Change the input source. Input sources available can vary depending on the Display Device Models.
3 Using MDC This menu shows a list of display devices which have following errors - fan error, temperature error, brightness sensor error, or lamp error. Select a display device from the list. The Repair button will be enabled. Click the refresh button to refresh the error status of the display device. The recovered display device will disappear from the Fault Device List. Fault Device Alert Display device in which error is detected will be reported by email. Fill in all required fields.
3 Using MDC 3.6.9 Screen Adjustment The screen settings (contrast, brightness, etc.) can be adjusted. Choose display devices from the list of sets, and select the Picture tab. Custom Select an item and change the corresponding screen setting. Color and Tint are not available if the input source is PC. Red, Green, Blue and PC Screen Adjustment are not available if the input source is Video.
3 Using MDC Blue Customize the intensity of blue color for the selected display device.
3 Using MDC Options Dynamic Contrast Adjust the Dynamic Contrast for the selected display device. Gamma Control Change the gamma value for the selected display. Auto Motion Plus This option is used to view dynamic images. Off: Disable the Auto Motion Plus function. Clear: Set the level of Auto Motion Plus to clear. This mode is suitable to display vivid images. Standard: Set the level of Auto Motion Plus to standard. Smooth: Set the level of Auto Motion Plus to smooth.
3 Using MDC Size Picture Size Adjust the screen size for the selected display device. The Detail item will be disabled if Picture Size is set to a mode that does not support detailed configuration. The -/+ buttons can be used to adjust Zoom. The screen can be relocated using the up/down/left/right buttons. Detail You can view details of the selected screen size. PC Screen Adjustment Frequency adjustment or fine-tuning is available by using the -/+ buttons in Coarse or Fine.
3 Using MDC 3.6.10 Sound Adjustment You can change the sound settings. Choose display devices from the list of sets, and select the Sound tab. The Bass or Treble item will be disabled if the item is not supported by the selected set. Bass Adjust the bass for the selected display. Treble Adjust the treble for the selected display. Balance (L/R) Adjust the volume of the left and right speakers of the selected display device.
3 Using MDC 3.6.11 System Setup Choose display devices from the list of sets, and select the System tab. Video Wall The Video Wall function can be used to display part of a whole picture or repeat the same picture on each of connected multiple display devices. Video Wall is enabled only when devices are in the group. Video Wall Enable or disable Video Wall. Format Select the format to display the split screen.
3 Using MDC H Select the number of horizontal display devices. A maximum of 15 displays can be arranged in a row. A maximum of 6 can be assigned to V if 15 is assigned to H. V Select the number of vertical display devices. A maximum of 15 displays can be arranged in a row. A maximum of 6 can be assigned to V if 15 is assigned to H. Screen Position View the layout of displays (configured by the screen divider) or change the layout as required.
3 Using MDC PIP Basic information required to adjust PIP will appear in the menu screen. PIP will be disabled when Video Wall is ON. Note that Picture Size is disabled when PIP is ON. PIP Size View the PIP Size of the current display. PIP Source Select a PIP input source. Sound Select Select and enable the sound from either the primary screen or secondary screen. Channel The channel can be changed if PIP Source is TV.
3 Using MDC General User Auto Color Automatically adjust the screen colors. Available only in PC mode. Auto Power Set the product to automatically power on. Standby Control Set the standby mode to activate if an input source is not detected. Fan & Temperature Configure the settings required to detect the fan speed and internal temperature for the product's protection. Fan Control Select a method to configure the fan speed. Fan Speed Configure the fan speed.
3 Using MDC Security Safety Lock Lock the on-screen menus. To unlock the menus, set Safety Lock to Off. Button Lock Lock the buttons on the display device. To unlock the buttons, set Button Lock to Off. OSD Display Source OSD Select whether to display a message when the Source is changed. Not Optimum Mode OSD Select whether to display a message when a non-compatible mode is selected. No Signal OSD Select whether to display a message when there is no input signal.
3 Using MDC Time Clock Set Change the current time on the selected display device according to the time set on a PC. If the time is not set on the display device, null values will be displayed. Timer On Time: Set the time to power on the selected display device. Off Time: Set the time to power off the selected display device. Volume: Specify the volume of the display device when it is powered on by On Time.
3 Using MDC Once: Activate the timer only one time. EveryDay: Activate the timer every day. Mon~Fri: Activate the timer from Monday through Friday. Mon~Sat: Activate the timer on Saturdays and Sundays. Manual: Customize days of the week. The checkboxes to select days of the week below Repeat are enabled only if Manual is selected. Holiday Management Holiday Management allows you to prevent devices that are set to be powered on by the Timer from turning on at a specified date.
3 Using MDC Screen Burn Protection Pixel Shift Move the screen slightly at specified time intervals to prevent screen burn-in. Screen Saver This function prevents screen burn-in when the screen of the selected display device is left idle for an extended period of time. Interval: Set the interval to activate the Screen Saver. Mode: The Time setting can vary for each Mode.
3 Using MDC The Safety Screen function can be used to prevent screen burn-in when a stationary image displays on the screen of a display device for an extended period of time. Lamp Control Lamp Control is used to adjust the backlight to reduce power consumption. Automatically adjust the backlight of the selected display device at a specified time. If Manual Lamp Control is adjusted, Auto Lamp Control will automatically switch to Off. Manually adjust the backlight for the selected display.
3 Using MDC 2 Reset Reset Picture Reset the screen settings. Reset Sound Reset the sound settings. Reset System Reset the system settings. Reset All Reset the screen, sound and system settings at the same time. 3 Edit Column Select the items you want to display in the list of sets. 4 Information View the program information.
3 Using MDC 3.6.13 Other Functions Resizing a Window Place the mouse pointer on a corner of the program window. An arrow will appear. Move the arrow to customize the size of the program window.
3 Using MDC Group Management Creating Groups Create groups and manage the list of sets on a group basis. Duplicate group names cannot be used. 1 Right-click and select Group>Edit in the display device list section on the left side of the program window. 2 In the Edit Group window displayed, click Add on the sub level or Add on the same level. Add on the sub level: Create a sub-group under the selected group. Add on the same level: Create a group on the same level as the selected group.
3 Using MDC The Add on the same level button is enabled only if at least one group is created. 3 Enter the group name. Deleting Groups 1 2 Select a group name, and click Edit. 3 Click Yes. The group will be deleted. In the Edit Group window displayed, click Delete. Renaming Groups 1 2 Select a group name, and click Edit. 3 If a cursor appears in the old group name, enter a new group name. In the Edit Group window displayed, click Rename.
3 Using MDC Schedule Management Creating Schedules Create and register a schedule on a group basis. 1 Click All Schedule List in the schedule section on the left side of the program window. The Add button will be enabled in the middle. 2 Click the Add button. The Add Schedule window will appear.
3 Using MDC 3 Click Add below the Device Group item, and select the group you want to add a schedule to. 4 Select Date&Time/Action and click OK. The schedule will be added and a list of schedules will appear in the set list window. Device Group: Select a group. Date&Time Instant Execution: Run the schedule immediately. Timer Set the date, time and interval to run the schedule. Action: Select a function that will activate at the specified time and interval.
3 Using MDC 3.6.14 Troubleshooting Guide Issue The display you want to control does not appear on the system information chart. Solution 1. Check the connection of the RS232C cable (check that the cable is properly connected to appropriate serial port). 2. Check that another display with a duplicate ID is not connected. Connecting displays with a duplicate ID can cause the displays not to be shown due to data collision. 3. Check that the display ID is within the range of 0 and 99.
3 Using MDC How display properties are shown when multiple displays are used 1 2 3 When no display is selected: The default value is displayed. When one display is selected: Settings for the selected display are displayed. When two displays are selected (e.g. in sequence of ID 1 andID 3): The settings for ID 1 are displayed before the settings for ID 3. 4 When the All+Select checkbox is checked and all displays are selected: The default settings are displayed.
4 Screen Adjustment Configure the Picture settings (Brightness, Colo(u)r Tone, etc.). The layout of the Picture menu options may vary depending on the product. 4.1 Picture Mode O MENU m Picture Picture Mode ENTER Select a picture mode (Picture Mode) suitable for the environment where the product will be used. Different Picture Mode options are displayed depending on the current input source.
4 4.2 Screen Adjustment Backlight / Contrast / Brightness / Sharpness / Colo(u)r / Tint(G/R) O MENU m Picture ENTER Your product has several options for adjusting picture quality. Select an option using the buttons, and then press [ When done, press [ 4.3 and ]. Use the arrow keys to adjust the option value or select an option setting. ]. When you make changes to Backlight, Contrast, Brightness, Sharpness, Colo(u)r or Tint (G/ R), the OSD will be adjusted accordingly.
4 Screen Adjustment 4.3.1 Picture Size If you have a cable box or satellite receiver, it may have its own set of screen sizes as well. However, we highly recommend you use your product 16:9 mode most of the time. 16:9: Sets the picture to 16:9 wide mode. Zoom1: Use for moderate magnification. Cuts off the top and sides. Zoom2: Use for a stronger magnification. Wide Fit (depending on the country): Enlarges the aspect ratio of the picture to fit the entire screen.
4 Screen Adjustment 3 4 5 Press the or Press the [ button to move the picture up or down. ] button. Select Close by pressing the and buttons sequentially. To reset the picture position, press Reset. To use the Position function after selecting Screen Fit in HDMI (1080i/1080p) or Component (1080i/1080p) or Custom, follow these steps. 1 2 3 4 5 Press the button to select Position. Press the [ Press the Press the [ ] button. / / / button to move the picture. ] button.
4 Screen Adjustment Adjust frequency values/positions and fine tune the settings automatically. This option is available when the input source is PC. 4.5 Using the 3D function (UE46A & UE55A models only) O MENU m 4.5.1 Picture 3D ENTER 3D Mode This exciting new feature enables you to view 3D content. In order to fully enjoy this feature, you must purchase a pair of Samsung 3D Active Glasses to view 3D video. 4.5.
4 Screen Adjustment 3D Mode Off 3D Turns the 3D function off. 3D Operation 2D Changes a 3D image to 2D. Side by Side Displays two images next to each other. Top & Bottom Displays one image above another. Line by Line Displays the images for the left and right eye alternately in rows. Vertical Stripe Displays the images for the left and right eye alternately in columns. Checker Board Displays the images for the left and right eye alternately in pixels.
4 Screen Adjustment Resolution Frequency (Hz) 1280 x 720p 25 / 50 Hz 1920 x 1080i 25 / 50 Hz 1920 x 1080p 25 / 50 Hz Resolution supported for HDMI PC mode The resolution for HDMI PC mode is optimized to 1920 x 1080 input. An input resolution other than 1920 x 1080 may not be displayed properly in 3D display or full screen mode. How to watch the 3D image Method 1 1 Some 3D modes may not be available depending on the format of the image source.
4 4.6 Screen Adjustment 3D Active Glasses from Samsung’s previous product (IR type) or other manufacturers not be supported. When the product is initially powered on, may take some time until the 3D display is optimized. The 3D Active Glasses may not work properly if there is any other 3D product or electronic devices turned on near the glasses or product. If there is a problem, keep other electronic devices as far away as possible from the 3D Active Glasses.
4 Screen Adjustment 4.6.2 Dynamic Contrast Adjust the screen contrast. Off / Low / Medium / High 4.6.3 Shadow Detail Increase the brightness of dark images. 4.6.4 Gamma Adjust the primary color intensity. 4.6.5 Expert Pattern Use the Expert Pattern function to calibrate the picture. If the OSD menu disappears or a menu other than the Picture menu is opened, the product saves the calibration and the Expert Pattern screen disappears. Off Turns the Expert Pattern function off.
4 Screen Adjustment 4.6.8 White Balance Adjust the colour temperature for a more natural picture. R-Offset / G-Offset / B-Offset: Adjust each color (red, green, blue) darkness. R-Gain / G-Gain / B-Gain: Adjust each color (red, green, blue) brightness. Reset: Resets the White Balance to it’s default settings. 4.6.9 10p White Balance (Off / On) Controls the white balance in 10 point interval by adjusting the red, green, and blue brightness. Interval: Select interval to adjust.
4 4.7 Screen Adjustment Picture Options O MENU m Picture Picture Options ENTER Select an option using the up and down arrow keys, and the press [ the setting, and then press [ ]. Use the arrow keys to change ]. When connecting a PC, you can only make changes to the Colo(u)r Tone. Picture Options Color Tone Off Color Temp. 10000K Digital Noise Filter Off MPEG Noise Filter Off HDMI Black Level Normal Film Mode Motion Plus 4.7.
4 Screen Adjustment 4.7.4 MPEG Noise Filter Reduces MPEG noise to provide improved picture quality. Off / Low / Medium / High / Auto 4.7.5 HDMI Black Level Lets you adjust the screen depth by selecting a black level. Normal / Low Available only in HDMI mode. 4.7.6 Film Mode Sets the product to automatically sense and process film signals from all sources and adjust the picture for optimum quality. Off / Auto1 / Auto2 Available in AV, COMPONENT (480i / 1080i) and HDMI (480i / 1080i). 4.
4 Screen Adjustment This is only supported if the Auto Motion Plus (or Motion Plus) is set to Custom. 4.8 Reset: Restore Motion Plus settings to default values. The color on screen may vary with this option unintentionally. Disabled when PIP is set to On. Reset Picture O MENU m Picture Reset Picture ENTER Resets your current picture mode to its default settings.
5 5.1 Sound Adjustment Configure the sound (Sound) settings for the product. Sound Mode O MENU m Sound Sound Mode ENTER Use the up and down arrow keys to select an option, and then press [ ]. Sound Sound Mode Standard Sound Effect 3D Audio Low Speaker Settings Reset Sound Standard: Selects the normal sound mode. Music: Emphasizes music over voices. Movie: Provides the best sound for movies. Clear Voice: Emphasizes voices over other sounds.
5 Sound Adjustment SRS CS Headphone (Off / On) You can hear virtual 5.1ch surround sound over the headphones. Equalizer The Equalizer displays a series of sliders. Use the up and down arrow keys to select a slider. Use the left and right arrow keys to change the slider’s value. To Reset the Equalizer, select Reset and press [ ], then select YES and press [ ]. To exit, select Close, and then press [ ]. Equalizer is available in the standard sound mode only. 5.
5 Sound Adjustment Auto Volume (Off / Normal / Night) Normal equalizes the volume level on each channel, so that when you change channels, the volume level is the same. Night equalizes and decrease the volume level on each channel, so each channel is quieter. Night is useful at night, when you may want to keep the volume low. To use the volume control of a connected source device, set Auto Volume to Off.
Media 6.1 MagicInfo Lite O MENU m Media MagicInfo Lite ENTER[ ] Press the MagicInfo Lite button on the remote control. 6.1.1 MagicInfo Lite Player Guide MagicInfo Lite Player allows you to play content (image, video, document files) at a desired time. You can play content saved in internal memory or USB memory. You can also play content via MagicInfo Lite Server after connecting to a network. For further details about how to use MagicInfo Lite Server, refer to the MagicInfo Lite Server user manual.
Media Videos O MENU m Media Videos ENTER[ ] Connecting a USB Device 1 2 Turn on your product. Connect a USB device containing photo, music and/or movie files to the USB port on the back or side panel of the product. 3 When a USB device is connected to the product, the Connected Device screen appears. Select a connected device, and then press [ ]. 6.2.1 Playing a Video 1 2 Press the Press the [ / / / button to select the desired video in the file list. ] button or [ ▶ ](Play) button.
Media Supported Video Formats File Extension *.avi *.mkv *.asf *.wmv *.mp4 *.3gp *.vro *.mpg *.mpeg *.ts *.tp *.trp Container AVI MKV ASF ASF MP4 Video Codec Resolution Frame rate(fps) Bit rate(M bps) DivX 3.11 / 4.x / 5.1 / 6.0 1920x1080 6 ~ 30 8 H.264 BP / MP / HP 1920x1080 6 ~ 30 25 MPEG4 SP / ASP 1920x1080 6 ~ 30 8 Motion JPEG 1920x1080 6 ~ 30 8 DivX 3.11 / 4.x / 5.1 / 6.0 1920x1080 6 ~ 30 8 H.
Media Sound or video may not work if the contents have a standard bitrate/frame rate above the compatible Frame/sec listed in the table above. If the Index Table is in error, the Seek (Jump) function is not supported. You may experience file stuttering while playing a video through a network connection. Video content can not be played, if there are many contents in one file. When you play video over a network connection, the video may not be played smoothly.
Media 4 Press the or button to select a chapter you want to view. Playback will start from the chapter you selected.
Media 6.3 Photos O MENU m Media Photos ENTER[ ] Connecting a USB Device 1 2 Turn on your product. Connect a USB device containing photo, music and/or movie files to the USB port on the back or side panel of the product. 3 When a USB device is connected to the product, the Connected Device screen appears. Select a connected device, and then press [ ]. 6.3.1 Viewing a Photo (or Slide Show) 1 2 Press the / Press the [ / / button to select the desired file in the file list. ] button.
Media Music O MENU m Media Music ENTER[ ] Connecting a USB Device 1 2 Turn on your product. Connect a USB device containing photo, music and/or movie files to the USB port on the back or side panel of the product. 3 When a USB device is connected to the product, the Connected Device screen appears. Select a connected device, and then press [ ]. 6.4.1 Playing Music 1 2 Press the / Press the [ / / button to select the desired music file in the file list. ] button or [ ▶ ](Play) button.
Media Playing My Playlist Select the My Playlist folder and it will play automatically. Press the or button to play a different music file within the play list. To delete a file from My Playlist, select the recycle bin icon next to the file you want to delete by using the direction buttons, and then press [ ]. The file will be deleted from My Playlist.
Media 6.5 Videos / Photos / Music - Additional Functions 6.5.1 Sorting the file lists To sort files in the file lists, select the / button. Then, press the [ (Sorting) icon in the top right of the screen by using the / / ] button. The checks below indicate which media the sort criteria apply to. Sort Criteria Operation Videos Photos Music Folder view Displays the whole folder. You can view the file name and thumbnail by selecting the folder.
Media 6.5.2 Videos/Photos/Music Play Option menu When playing video or photo files, you can press the TOOLS button to display an Options menu. Below are a series of tables listing the options available and the media each option applies to. Option Name Operations List Return to the file list. Play / Pause You can start or stop. Alternatively, the (Play) or be used. II ▶ Videos Photos Music c c c c c (Pause) button on the remote can Previous / Next Go to previous / next photo file.
Media Option Name Operations Videos Start Slide Show / Stop Slide Show You can start or stop a slide show. Slide Show Speed You can select the slide show speed during Alternatively, use the remote. ▶ or II Photos Music c button on the the slide show. Alternatively, use the ◀◀ c or button on the remote. ◀◀ Slide Show Effect You can set various slide show effects. c Background Music On / Off You can start or stop background music.
Media 6.6 Source O MENU m Media Source ENTER[ ] Source allows you to select a variety of sources and change source device names. 6.6.1 Source You can display the screen of a source device connected to the product. Select a source from Source List to display the screen of the selected source. Media Magicinfo Lite Videos Photos Music Source AllShare The input source can also be changed by using the SOURCE button on the remote control.
Media When connecting a PC to the HDMI IN port with HDMI cable, you should set the product to PC mode under Edit Name. When connecting a PC to the HDMI IN port with HDMI to DVI cable, you should set the product to DVI PC mode under Edit Name. When connecting an AV devices to the HDMI IN port with HDMI to DVI cable, you should set the product to DVI Devices mode under Edit Name. 6.6.
Media 6.7 AllShare O MENU m Media AllShare ENTER[ ] AllShare connects your product and compatible Samsung mobile phones/ devices through a network. You can play media contents including videos, photos, and music saved on your mobile phones or the other devices (such as your PC) by controlling them on the product via the network. For more information, visit “www.samsung.com” or contact the Samsung call center. Mobile devices may need additional software installation.
7 7.1 Network Network Settings 7.1.1 Connecting to a Wired Network There are three ways to attach your product to your LAN using cable: You can attach your product to your LAN by connecting the LAN port on the back of your product to an external modem using a LAN cable. See the diagram below.
7 Network access the Internet so you do not have to enter them manually. Most home networks are Dynamic Networks. Some networks require a Static IP address. If your network requires a Static IP address, you must enter the IP address, subnet mask, gateway, and DNS values manually on your product Cable Setup Screen when you set up the network connection. To get the IP address, subnet mask, gateway, and DNS values, contact your Internet Service Provider (ISP).
7 Network Manual Network Setup Use the Manual Network Setup when connecting your product to a network that requires a Static IP address. Getting the Network Connection Values To view the Network connection values on most Windows computers, follow these steps. 1 2 3 4 Right click the Network icon on the bottom right of the screen. In the pop-up menu that appears, click Status. On the dialog that appears, click the Support tab. On the Support Tab, click the Details button.
7 Network 7.1.3 Connecting to a Wireless Network To connect your product to your wireless network, you need a wireless router or modem and a Samsung Wireless LAN adapter (WIS09ABGN, WIS09ABGN2 or WIS10ABGN - sold separately), which you connect to your product back or side panel USB port. See the illustration below.
7 Network Ad Hoc WPS (PBC) One Foot Connection The product may not recognize the Samsung Wireless LAN adapter if you connect it to the product with a USB hub or USB extension cable other than the cable supplied with the product. 7.1.4 Wireless Network Setting Automatic Network Setup Most wireless networks have an optional security system that requires devices that access the network to transmit an encrypted security code called an Access or Security Key.
7 Network If you want to set up the connection manually, select IP Settings. Then, go to the next section, “How to set up manually”. Manual Network Setup Use the Manual Network Setup when connecting your product to a network that requires a Static IP address or if the automatic connection process has failed. Getting the Network Connection Values To view the Network connection values on most Windows computers, follow these steps: 1 2 3 4 Right click the Network icon on the bottom right of the screen.
7 Network 11 Enter the first portion of the IP Address (for example, 105) into the first entry field using the number keys on your remote. Press the 12 13 button to go to the next field. Enter the next portion of the IP Address. Press the button to go to the next field. Repeat the entry process for each field in the IP Address. If you make a mistake when entering a number, re-enter the number to correct it. You can also press the 14 15 16 17 or button to change the number one unit at a time.
7 Network If One Foot Connection does not connect your product to your Router, a pop- up screen appears on the screen notifying you of the failure. If you want to try using One Foot Connection again, reset the wireless router, and then try again from Step 1. You can also choose one of the other connection setup methods. 5 6 The network connection screen appears, and network setup is done. Place the wireless router in a desired location.
7 Network 7.2 If a device is connected once, it is displayed in the Network Setting list. When you connect to it again, you can find it in the list. Network Status O MENU m Network Network Status ENTER You can check the current network and Internet status. Network Network Settings Network Status AllShare Settings MagicInfo Lite Settings 7.3 AllShare Settings O MENU m Network AllShare Settings ENTER "MM4IBSF 4FUUJOHT .FEJB 0GG Media (On / Off): Enables or disables the media function.
7 Network Delete: Deletes the devices from the list. This function only deletes the name of the device from the list. If the deleted device is turned on or tries to connect to the product, it may appear on the list again. Using the Media Function An alarm window appears informing you that media contents (videos, photos, music) sent from a mobile phone will be displayed on your product. The contents are played automatically 3 seconds after the alarm window appears.
7 Network 3 Internal Memory: Displays the space currently being used or deletes all content. USB: Displays the space currently being used. Slideshow Image Viewer Time: Sets the time length you want to display images played from Local Schedule or by one of the auto playback functions. PPT Viewer Time: Sets the time length you want to display each page of a document file played from Local Schedule or by one of the auto playback functions.
8 8.1 System Multi Control O MENU m System Multi Control ENTER Assign an individual ID to your product. 8.1.1 Configuring settings for Multi Control MDC Connection Select a method to connect to MDC to receive the MDC signal. RS232C MDC Communicate with MDC via the RS232C-stereo cable. RJ45 MDC Communicate with MDC via the RJ45 cable. ID Setup Assign an ID to a set. (Range: 0~99) Press or to select a number, and press [ ].
8 8.2 System Time O MENU m System Time ENTER You can configure Clock Set or Sleep Timer. You can also set the product to automatically turn on or off at a specified time using the Timer function. 8.2.1 Clock set Set the clock to use the various various timer features of the product. If you disconnect the power cord, you have to set the clock again. Changing the Setting for Clock Clock Set Set the Date and Time. Select Clock Set. Select Date or Time, and then press [ ].
8 System The check mark indicates days you’ve selected. Time: Set the hour and minute. Use the number buttons or the up and down arrow keys to enter numbers. Use the left and right arrow buttons to change entry fields. Volume: Set the desired volume level. Use the left and right arrow buttons to change the volume level. Source: Select the input source of your choice.
8 System - Delete: Delete all items from the list of holidays. Select Delete. The message "Delete all holidays?" will appear. Select Yes. All holidays will be deleted. Apply: Set the On Timer and Off Timer to not activate on public holidays. Press ENTER[ ] to select the On Timer and Off Timer settings you do not want to activate. The selected On Timer and Off Timer will not activate.
8 8.4 System Eco Solution O MENU m System Eco Solution ENTER &DP 4PMVUJPO &OFSHZ 4BWJOH 0GG &DP 4FOTPS 0GG /P 4JHOBM 1PXFS 0GG "VUP 1PXFS 0GG 8.4.1 NJO 0GG Energy Saving Save power with the Energy Saving feature. While Energy Saving mode is active, the product power consumption will be controlled to save power. 8.4.2 Off / Low / Medium / High / Picture Off Eco Sensor (Off / On) To enhance your power savings, the picture settings will automatically adapt to the light in the room.
8 System 8.4.3 No Signal Power Off To avoid unnecessary energy consumption, you can set how long you want the product to remain on if it’s not receiving a signal. Off / 15 min. / 30 min. / 60 min. 8.4.4 Disabled when an attached PC is in power saving mode. Auto Power Off (Off / On) The product will automatically turn off if you don’t press a button on the remote or touch a button on product front panel within 4 hours to prevent overheating. 8.
8 System 8.5.3 Change PIN The Change PIN screen will appear. Choose any 4 digits for your PIN and enter it in Enter New PIN. Reenter the same 4 digits in Confirm New PIN. When the Confirm screen disappears, press the Close button. The product has memorized your new PIN. 8.6 PIP O MENU m System PIP , ENTER If you have set mode in PIP (Picture-in-Picture), you cannot adjust the Picture Size. For PIP sound, refer to the Sound Select instructions.
8 8.7 System Auto Protection Time O MENU m System Auto Protection Time ENTER If the screen displays a still image for a certain period of time you define, the product activates the screen saver to prevent the formation of burnt in ghost images on the screen.
8 8.8 System Screen Burn Protection O MENU m System Screen Burn Protection ENTER To reduce the possibility of screen burn, this unit is equipped with Pixel Shift screen burn prevention technology. Pixel Shift moves the picture slightly on the screen. The Pixel Shift Time setting allows you to program the time between movements of the picture in minutes. Screen Burn Protection Pixel Shift On Timer Off Pixel Side Gray 8.8.
8 System Mode: You can change the Safety Screen Type. Period: Use this function to set the execution period for each mode set in the timer. Time: Within the set period of time specify a time for execution. 8.8.3 Pixel This function prevents after-images by moving many pixels on the screen. 8.8.4 Side Gray Select the brightness of the grey for the screen background.
8 8.9 System Video Wall O MENU m System Video Wall ENTER Customize the layout of multiple displays that are connected to form a video wall. In addition, display part of a whole picture or repeat the same picture on each of the connected multiple displays. To display multiple images, refer to MDC Help or the MagicInfo user guide. Some models may not support the MagicInfo function.
8 System according to the number entered. A maximum of 15 displays can be assigned to the horizontal arrangement. The screen can be divided into a maximum of 100 screens (horizontal and vertical screens multiplied). For example, if the horizontal arrangement is set to 15, a maximum of 6 displays can be assigned to the vertical arrangement. Conversely, if the vertical arrangement is set to 15, a maximum of 6 displays can be assigned to the horizontal arrangement.
8 System 8.10 Source AutoSwitch Settings O MENU m System Source AutoSwitch Settings ENTER Turning on the display with Source AutoSwitch On, and the previous video source selection is not active, the display will automatically search the different video input sources for active video. Source AutoSwitch When the Source AutoSwitch is On, the display video source will automatically be searched for active video.
8 System 8.11 General O MENU m System General ENTER General Max. Power Saving On Game Mode Off BD Wise On Auto Power Off Standby Control Auto Lamp Schedule Off OSD Display 8.11.1 Max. Power Saving Turns off the product to reduce power consumption after the PC has been left idle for a specified period of time. 8.11.2 Game Mode When connecting to a game console such as PlayStation™ or Xbox™, you can enjoy a more realistic gaming experience by selecting game mode.
8 System 8.11.3 BD Wise Provides the optimal picture quality for Samsung DVD, Blu-ray and Home Theater products which support BD Wise. When BD Wise is turned On, the picture mode is automatically changed to the optimal resolution. Available when you connect Samsung products that support BD Wise through an HDMI cable to the product. 8.11.4 Auto Power Enabling this option will automatically power on the product if the power cable is connected. 8.11.
8 System 8.11.8 Power On Adjustment You can set the warm-up time for the screen to turn on after the power button is pressed. (Range: 0 – 50 seconds) A warm-up time that is too short may damage the product due to overvoltage. 8.11.9 Temperature Control Temperature Control This function detects the internal temperature of the product. You can specify the temperature range that is acceptable. The default temperature is set to 77 C.
8 System 8.12 Anynet+(HDMI-CEC) O MENU m 8.12.1 System Anynet+(HDMI-CEC) ENTER Anynet+(HDMI-CEC) What is Anynet+? Anynet+ is a function that enables you to control all connected Samsung devices that support Anynet+ with your Samsung product remote. The Anynet+ system can be used only with Samsung devices that have the Anynet+ feature. To be sure your Samsung device has this feature, check if there is an Anynet+ logo on it.
8 System Anynet+ Menu (device_name) Tools Description Shows the tools menu of the connected device. E.g. if a DVD player is connected, the tools menu of the DVD player will appear. Depending on the device, this menu may not be available. (device_name) Title Menu Shows the title menu of the disc in the connected device. E.g. If a DVD player is connected, the title menu of the movie in the DVD player will appear. Depending on the device, this menu may not be available. 8.12.
8 System Listening through a Receiver You can listen to sound through a receiver (i.e Home Theater) instead of the Internal Speaker. 1 2 Select Receiver and set to On. Press the EXIT button to exit. If your receiver supports audio only, it may not appear in the device list. When the receiver (i.e Home Theater) is set to On, you can hear sound output from the product Optical jack.
8 System Problem The connected device is not displayed. Possible Solution Check whether or not the device supports Anynet+ functions. Check whether or not the HDMI cable is properly connected. Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+ setup menu. Search Anynet+ devices again. Anynet+ requires an HDMI connection. Make sure the device is connected to your product with an HDMI cable. Some HDMI cables may not support Anynet+ functions.
8 System 8.13 DivX® Video On Demand O MENU m System DivX® Video On Demand ENTER Shows the registration code authorized for the product. If you connect to the DivX web site and register using that code, you can download the VOD registration file. For more information about DivX® VOD, visit “http://vod.divx.com”. 8.14 Network Remote Control O MENU m System Network Remote Control ENTER Turn on/off or give permission to Samsung mobile phone devices to connect with and control the product.
9 9.1 Support Software Upgrade O MENU m Support Software Upgrade ENTER The Software Upgrade menu lets you upgrade your product software to the latest version. Current Version: This is the software version already installed in the product. Be careful not to turn off the power until the upgrade is complete. The product will turn off and on automatically after completing the software upgrade. When you upgrade software, all video and audio settings you have made will return to their default settings.
9 9.2 Support Contact Samsung O MENU m Support Contact Samsung ENTER View this information when your product does not work properly or when you want to upgrade the software. You can find information regarding our call centers and how to download products and software.
10 MagicInfo Lite 10.1 File Formats Compatible with MagicInfo Lite Player [Read before using MagicInfo Lite Player] Supported USB-device file systems include FAT16 and FAT32. (NTFS is not supported.) A file with a vertical and horizontal resolution larger than the maximum resolution cannot be played. Check the vertical and horizontal resolution of the file. Video that does not contain audio data is not supported. Check that the video file contains audio data.
10 MagicInfo Lite File Extension *.3gp *.vro *.mpg *.mpeg Video Codec Resolution Frame rate(fps) Bit rate (Mbps) Audio Codec H.264 BP / MP / HP 1920x1080 6 ~ 30 25 MPEG4 SP / ASP 1920x1080 6 ~ 30 8 ADPCM / AAC / HE-AAC VRO MPEG1 352x288 24 / 25 / 30 30 VOB MPEG2 1920x1080 24 / 25 / 30 30 MPEG1 352x288 24 / 25 / 30 30 MPEG2 1920x1080 24 / 25 / 30 30 H.264 1920x1080 6 ~ 30 25 MPEG2 1920x1080 24 / 25 / 30 30 H.
10 MagicInfo Lite Image Compatible image file format : Jpeg Supported maximum resolution : 15,360 x 8640 Supported image effects : 8 effects (Fade1, Fade2, Blind, Spiral, Checker, Linear, Stairs, Wipe) Flash Compatible with Flash 10.
10 MagicInfo Lite Power Point Compatible document file formats Extension : ppt, pptx Version : Office 97 ~ Office 2007 Functions not supported Animation effect 3D shapes (which will be displayed in 2D) Header and footer (some subitems are not supported) Word Art Align (A group alignment error may occur) Office 2007 (SmartArt is not fully supported. 97 out of 115 subitems are supported.
10 MagicInfo Lite 10.2 Network Schedule 10.2.1 Connecting to a server To use the MagicInfo Lite Server, the clock on the monitor must be set through the server (web). To use local schedules and AutoPlay only, without using the MagicInfo Lite Server, the clock must be set using the remote control. Network setup To run MagicInfo Lite, connect to a network. Refer to 130 page for details about the Network Settings menu. Server setup Go to MENU Network MagicInfo Lite Settings Server.
10 MagicInfo Lite 10.2.2 MagicInfo Lite Settings O MENU m Media MagicInfo Lite ENTER [ ] Press the MagicInfo Lite button on the remote control. You can view whether the server is connected (approval) in the MagicInfo Lite menu screen. To view whether the server is connected when a network schedule is running, press INFO on the remote.
10 MagicInfo Lite 3 Select Device from the top menu bar. 4 Select Lite Device from the menus on the left.
10 MagicInfo Lite 5 Select View Unapproved Lite Device from the sub-menus of Lite Device. 6 Select the Approve button for your device from the list of unapproved Lite devices. Pressing the INFO button on the remote when a network schedule is running will display the details of the schedule. Check that the correct device has been selected by viewing the device ID in the details. 7 Enter the information required to approve the device. Device Name: Enter the device name.
10 MagicInfo Lite 8 Select the View All Lite Device menu to check that the device has been registered. 9 When the device is approved by the server, the schedule registered in the selected group will be downloaded to the device. The schedule will run after it is downloaded. For further details on how to configure a schedule, refer to the . If a device is deleted from the list of devices approved by the server, the device will reboot to reset its settings.
10 MagicInfo Lite 10.2.4 Setting the current time A schedule may not run if the time set on the device is different from the server's current time. 1 Go to the tabs Device 2 3 Select your device. Time. Select Clock Set, and sync the time with the server. For further details on how to manage the time (scheduling, holiday management, etc.), refer to the .
10 MagicInfo Lite 10.3 Local Schedule Run a schedule created by Local Schedule Manager. Go to Local Schedule Manager Select the content you want to run This menu is disabled if no schedule was created by Local Schedule Manager. 1 2 Select Local Schedule Manager in the MagicInfo Lite menu screen. Run a schedule created by local schedule. 10.4 Local Schedule Manager Configure the settings for playback from Local Schedule.
10 2 MagicInfo Lite Select Create in the Local Schedule Manager screen. Local Schedule Manager Storage Internal Memory No Playing Schedule Create Edit Delete Run Info Close 3 Select Time to set the time you want to play content. To create a schedule that starts on one day and finishes the next day, the time must be set as shown below. E.g.
10 4 MagicInfo Lite Select Contents to specify the content you want to play. Contents Internal Memory No Item USB Folder1 Menu1.jpg Done Menu2.jpg Deselect Cancel 5 6 Select Save. Select the memory space you want to save the content to. Create Time 12:00 am ~ 02:00 pm Delete Conten Where do you want to save? Time Save Conten ancel Internal 7 USB Cancel Check that the schedule has been added to the Local Schedule Manager.
10 MagicInfo Lite 10.4.2 Modifying a local schedule Local Schedule Ensure at least one local schedule Local Schedule is registered. 1 Select Local Schedule Manager in the MagicInfo Lite menu screen. Network Schedule Local Schedule ・ Local Schedule Manager Contents Manager Close Internal AutoPlay USB AutoPlay 2 Mode Server USB Network Schedule Connected Disconnected Select the local schedule you want to modify.
10 3 MagicInfo Lite Select Edit. Edit Time 12:00 am ~ 02:00 pm Contents Time Delete Menu1.jpg --:-- am ~ --:-- pm Save Contents No Item Cancel 4 Change the details of the local schedule. Next, select Save. 10.4.3 Deleting a local schedule Local Schedule Ensure at least one local schedule Local Schedule is registered. 1 Select Local Schedule Manager in the MagicInfo Lite menu screen.
10 2 MagicInfo Lite Select the local schedule you want to delete. Local Schedule Manager Storage Internal Memory Create Edit No Playing Schedule Delete 20110101_1200.Isch Run Info Close 3 Select Delete.
10 MagicInfo Lite 10.4.4 Running a local schedule Local Schedule Ensure at least one local schedule Local Schedule is registered. 1 Select Local Schedule Manager in the MagicInfo Lite menu screen. Network Schedule Local Schedule ・ Local Schedule Manager Contents Manager Close Internal AutoPlay USB AutoPlay 2 Mode Server USB Network Schedule Connected Disconnected Select the local schedule you want to run. Next, select Run.
10 MagicInfo Lite 10.4.5 Stopping a local schedule Local Schedule This function is enabled only when a schedule is running. Selecting Stop will change the running mode from local schedule to network schedule. 1 Select Local Schedule Manager in the MagicInfo Lite menu screen. Network Schedule Local Schedule ・ Local Schedule Manager Contents Manager Close Internal AutoPlay USB AutoPlay 2 Mode Server USB Network Schedule Connected Disconnected Select Stop.
10 MagicInfo Lite 10.4.6 Viewing the details of a local schedule Local Schedule 1 Select Local Schedule Manager in the MagicInfo Lite menu screen. Network Schedule Local Schedule ・ Local Schedule Manager Contents Manager Close Internal AutoPlay USB AutoPlay 2 Mode Server USB Network Schedule Connected Disconnected Select the local schedule you want to view the details of. Local Schedule Manager Storage Internal Memory No Playing Schedule Create Edit Delete 20110101_1200.
10 MagicInfo Lite 10.5 Contents Manager 10.5.1 Copying content 1 Select Contents Manager in the MagicInfo Lite menu screen. Network Schedule Local Schedule · Local Schedule Manager Contents Manager Close Internal AutoPlay USB AutoPlay 2 Mode Server USB Network Schedule Connected Disconnected Select the content you want to copy. If content under Internal Memory is selected: You can copy the content under Internal Memory to USB memory.
10 MagicInfo Lite 10.5.2 Deleting content 1 Select Contents Manager in the MagicInfo Lite menu screen. Network Schedule Local Schedule · Local Schedule Manager Contents Manager Close Internal AutoPlay USB AutoPlay 2 Mode Server USB Network Schedule Connected Disconnected Select the content you want to delete. Content under Internal Memory and USB memory can be deleted at the same time. Contents Internal Memory No Item USB Folder1 Menu1.jpg Delete Menu2.
10 MagicInfo Lite 10.6 Internal AutoPlay 10.6.1 Running Internal AutoPlay Ensure at least one content item exists under Internal Memory. 1 Select Internal AutoPlay in the MagicInfo Lite menu screen. Play content, which has been copied to Internal Memory, in alphabetical order. Network Schedule Local Schedule ・ Local Schedule Manager Contents Manager Close Internal AutoPlay USB AutoPlay Mode Server USB Network Schedule Connected Disconnected 10.7 USB AutoPlay 10.7.
10 MagicInfo Lite USB AutoPlay will automatically run if USB memory is connected when Network Schedule or Local Schedule is running. Network Schedule Local Schedule ・ Local Schedule Manager Contents Manager Close Internal AutoPlay USB AutoPlay Mode Server USB Network Schedule Connected Disconnected 10.8 When Content is Running 10.8.1 Viewing the details of the content that is running Press the INFO button on the remote control.
10 7 MagicInfo Lite Schedule Download: Displays the progress of a network schedule being downloaded from the server. Information Software Version : A-VNUSCDSP-100 Device Name : Monitor Device ID : FE-FF-FF-FF-FF Mode : Network Schedule Server : Connected USB : Connected Schedule Download : No Schedule to download Close 10.8.2 Changing the settings for the content that is running Press the TOOLS button on the remote control.
11 Troubleshooting Guide 11.1 Requirements Before Contacting Samsung Customer Service Center 11.1.1 Testing the Product Before calling Samsung Customer Service Center, test your product as follows. If the problem persists, contact Samsung Customer Service Center. Check if your product is operating normally by using the product test function. If the screen remains blank while the power LED blinks even when the product is correctly connected to a PC, perform product testing.
11 Troubleshooting Guide 11.1.3 Check the followings. Installation issue (PC mode) The screen keeps switching on and off. Check the cable connection between the product and PC, and ensure the connection is secure. ("2.2 Connecting and Using a PC") Blank spaces are found on all four sides of the screen when an HDMI or HDMI-DVI cable is connected to the product and PC. The blank spaces found on the screen have nothing to do with the product.
11 Troubleshooting Guide Screen issue The screen is not clear. The screen is blurry. Adjust Coarse and Fine. Remove any accessories (video extension cable, etc) and try again. Set the resolution and frequency to the recommended level. The screen appears unstable and shaky. There are shadows or ghost images left on the screen. Check that the resolution and frequency of the PC and graphics card are set within a range compatible with the product.
11 Troubleshooting Guide Remote control issue The remote control does not work. Make sure that the batteries are correctly in place (+/-). Check if the batteries are flat. Check for power failure. Make sure that the power cord is connected. Check for any special lighting or neon signs switched on in the vicinity. Source device issue A beeping sound is heard when my PC is booting. If a beeping sound is heard when your PC is booting, have your PC serviced.
11 Troubleshooting Guide 11.2 Q & A Question How can I change the frequency? Answer Set the frequency on your graphics card. "Windows XP": Go to Control Panel Themes Display Settings Appearance and Advanced Monitor and adjust the frequency in Monitor Settings. "Windows ME/2000": Go to Control Panel Settings Advanced Display Monitor and adjust the frequency in Monitor Settings.
11 Troubleshooting Guide Question How can I change the resolution? Answer "Windows XP": Go to Control Panel Themes Display Appearance and Settings and adjust the resolution. "Windows ME/2000": Go to Control Panel Display Settings and adjust the resolution. "Windows Vista": Go to Control Panel Personalization Personalize Appearance and Display Settings and adjust the resolution.
12 Specifications 12.1 General Model Name ME40A / DE40A ME46A / DE46A ME55A / DE55A Size 40 inches (101cm) 46 inches (116cm) 55 inches (138cm) Display area 885.6(H) x 498.15(V) 1018.08(H) x 572.67(V) 1209.6(H) x 680.4(V) Panel Display Color 16.7M 1.07B 921.2 x 536.1 x 29.9 mm / 10.5 kg 1056.3 x 612.3 x 29.9 mm / 12.5 kg 1246.4 x 718.2 x 29.9 mm / 17.1 kg (without stand) 36.3 x 21.1 x 1.2 inches / 23.1 Ibs 41.6 x 24.1 x 1.2 inches / 27.6 Ibs 49.1 x 28.2 x 1.2 inches / 37.
12 Specifications Environme ntal considerat ions Operating Storage Temperature : 32 ˚F ~ 104 ˚F (0 ˚C ~ 40 ˚C) Humidity : 10 % ~ 80 %, non-condensing Temperature : -4 ˚F ~ 140 ˚F (-20 ˚C ~ 60 ˚C) Humidity : 5 % ~ 95 %, non-condensing Power Supply : This product uses 100 to 240V. Refer to the label at the back of the product as the standard voltage can vary in different countries. Plug-and-Play : This monitor can be installed and used with any Plug-and-Play compatible systems.
12 Specifications 12.2 PowerSaver The power-saving function of this product reduces power consumption by switching off the screen and changing the color of the power LED if the product is not used for a specified period of time. The power is not turned off in power-saving mode. To switch the screen back on, press any key on the keyboard or move the mouse. Power-savign mode only functions when the product is connected to a PC with a power-saving function.
12 Specifications 12.3 Preset Timing Modes This product can be set to only one resolution for each screen size to obtain the optimum picture quality due to the nature of the panel. Using a resolution other than the specified resolution may degrade the picture quality. To avoid this, it is recommended that you select the optimum resolution specified for your product. Check the frequency when you exchange a CDT product (connected to a PC) for an LCD product.
12 Specifications Resolution Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/ V) VESA, 1280 x 960 60.000 60.000 108.000 +/+ VESA, 1280 x 1024 63.981 60.020 108.000 +/+ VESA, 1280 x 1024 79.976 75.025 135.000 +/+ VESA, 1360 x 768 47.712 60.015 85.500 +/+ VESA,1920 x 1080 67.500 60.000 148.500 +/+ VESA,1920 x 1080 66.587 59.934 138.
12 Specifications 12.4 License TheaterSound HD, SRS and symbol are trademarks of SRS Labs, Inc. TheaterSound HD technology is incorporated under license form SRS Lab, Inc. Manufactured under license from Dolby Laboratories. Dolby and the doubleD symbol aretrademarks of Dolby Laboratories. Manufactured under license under U.S. Patent #’s: 5,451,942; 5,956,674; 5,974,380; 5,978,762; 6,487,535 & other U.S. and worldwide patents issued & pending. DTS and the Symbol are registered trademarks. & DTS 2.
Appendix Contact SAMSUNG WORLDWIDE If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center.
Appendix NORTH AMERICA U.S.A 1-800-SAMSUNG (726-7864) http://www.samsung.com CANADA 1-800-SAMSUNG (726-7864) http://www.samsung.com/ca http://www.samsung.com/ch_fr (French) MEXICO 01-800-SAMSUNG (726-7864) http://www.samsung.com LATIN AMERICA ARGENTINA 0800-333-3733 http://www.samsung.com BRAZIL 0800-124-421 4004-0000 http://www.samsung.com BOLIVIA 800-10-7260 http://www.samsung.com CHILE 800-SAMSUNG (726-7864) http://www.samsung.
Appendix EUROPE BOSNIA 05 133 1999 http://www.samsung.com BULGARIA 07001 33 11 http://www.samsung.com CROATIA 062 SAMSUNG (062 726 7864) http://www.samsung.com CZECH 800 - SAMSUNG (800-726786) http://www.samsung.com Samsung Electronics Czech and Slovak, s.r.o., Oasis Florenc, Sokolovská 394/17, 180 00, Praha 8 DENMARK 70 70 19 70 http://www.samsung.com FINLAND 030 - 6227 515 http://www.samsung.com FRANCE 01 48 63 00 00 http://www.samsung.
Appendix EUROPE SPAIN 902 - 1 - SAMSUNG (902 172 678) http://www.samsung.com SWEDEN 0771 726 7864 (SAMSUNG) http://www.samsung.com SWITZERLAND 0848-SAMSUNG (7267864, CHF 0.08/min) http://www.samsung.com/ch U.K 0330 SAMSUNG (7267864) http://www.samsung.com EIRE 0818 717100 http://www.samsung.com LITHUANIA 8-800-77777 http://www.samsung.com LATVIA 8000-7267 http://www.samsung.com ESTONIA 800-7267 http://www.samsung.com TURKEY 444 77 11 http://www.samsung.com http://www.samsung.
Appendix ASIA PACIFIC INDIA http://www.samsung.com 1800 1100 11 3030 8282 1800 3000 8282 1800 266 8282 INDONESIA 0800-112-8888 021-5699-7777 http://www.samsung.com JAPAN 0120-327-527 http://www.samsung.com MALAYSIA 1800-88-9999 http://www.samsung.com PHILIPPINES 1-800-10-SAMSUNG (726-7864) for PLDT http://www.samsung.com 1-800-3-SAMSUNG (726-7864) for Digitel 1-800-8-SAMSUNG (726-7864) for Globe 02-5805777 SINGAPORE 1800-SAMSUNG (726-7864) http://www.samsung.
Appendix AFRICA GHANA 0800-10077 http://www.samsung.com 0302-200077 KENYA 0800 724 000 http://www.samsung.com NIGERIA 0800-726-7864 http://www.samsung.com SENEGAL 800-00-0077 http://www.samsung.com SOUTH AFRICA 0860-SAMSUNG (726-7864) http://www.samsung.com TANZANIA 0685 88 99 00 http://www.samsung.com UGANDA 0800 300 300 http://www.samsung.
Appendix Optimum Picture Quality and Afterimage Burn-in Prevention Optimum Picture Quality To enjoy the optimum picture quality, go to Control Panel on your PC and adjust the resolution and refresh rate as follows. The picture quality of TFT-LCDs may degrade if the optimum resolution is not selected.
Appendix Prevention of Afterimage Burn-in What is afterimage burn-in? Afterimage burn-in should not occur when the LCD panel is operating normally. Normal operation refers to a continuously changing video pattern. If the LCD panel displays a fixed pattern for an extended period of time (more than 12 hours), a slight voltage difference may occur between the electrodes in pixels that control the liquid crystals.
Appendix Powering Off, Screen Saver and Power Saving Mode Power off the product for 4 hours after using it for 20 hours. (DE40A / DE46A / DE55A) Power off the product for 2 hours after using it for 12 hours. (ME40A / ME46A / ME55A / UE46A / UE55A / DE40A / DE46A / DE55A) Go to Display Properties > Power Supply on your PC and set the product to power off as required. Using a screen saver is recommended. It is best to use a single-color or moving-image screen saver.
Appendix The best way to protect the product from afterimage burn-in is switching the power off or setting the PC or system to run a screen saver when not in use. Also, Warranty service may be limited depending on instruction guide.
Appendix Correct Disposal of This Product (Waste Electrical & Electronic Equipment) - Europe only (Applicable in the European Union and other European countries with separate collection systems) This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset, USB cable) should not be disposed of with other household waste at the end of their working life.
Appendix Terminology OSD(On Screen Display) On screen display (OSD) allows you to configure on-screen settings to optimize the picture quality as required. It allows you to change the screen brightness, tint, size and many other settings using menus displayed on the screen. Gamma The Gamma menu adjusts the grey scale that represents middle tones on the screen. Adjusting the brightness brightens the whole screen, but adjusting Gamma only brightens the medium brightness.
Appendix Resolution Resolution is the number of horizontal pixels and vertical pixels that form a screen. It represents the level of display detail. A higher resolution displays a greater amount of information on the screen and is suitable for performing multiple tasks at the same time. E.g. A resolution of 1920 x 1080 consists of 1,920 horizontal pixels (horizontal frequency) and 1,080 vertical lines (vertical resolution).
Index Numerics O 3D Mode 104 OSD Rotation 161 A P Appendix 200 PC connection 51 Picture Size 102 B Batteries 29 C Changing the Resolution 54 Communicate with MDC via the RS232Cstereo cable.
