Specifications

, : _ _s_ _ 7¸
Using Direct Entry
I. Ttl]'non "dt_con]portentyou wan_-Io opcra'L<_(VCR D\D play_r etc.)
2. Look up lhe brand and code number{s) 7or"d_ compo_e_- o_ "d_ code l]s_-1_ "ddssect]o_.
3. Press and hold the component button vou want to program on the remote.
4. Enter the 4<tigit code t]om the remote control code list on the to]]o\viDg pages. _ the
indicator HasHes, you Have either entered an invalid code or the button isn't programmable.
5. Release the component button, point the remote at the component, and then press ON,,OFF
to see if the componem respo*_ds to the command. [t it doesn't, try pressi_g the compo_em
button and then ON*OFF again.
,, [f vou get no response, repeat these steps using the next code listed R_rvour brand, und[ the
c()mponent responds to the remote COI1]l]]a_lds.
[_ }Ol] try {t]] 1_](. cod(2s _'(77' your (o]]]poT]<}D[ ])]_]I](t {]_](t D()z't(2 \', ()rk try [ll{._ allt()]]]atic co(h._
s<arcb mcJtod. [}-at]ton]atic cod< seard-t <[oesYt'[ [iY<t the code [lt< r<n]oR is not con]patibh_
\_ith yOUr (X)I]]pol"t< Z't[.
How to Use the Remote After You've
Programmed It
Bccausu Ibis rcmotu cm_ control suvera] dJ_fL'rcnt components (TV. I)VD VCR saR'l[iR' rucuivcr
<'to.) i/ uses opc7'alJoYta[ _nodcs 17'iggc7'cd bv lhc co_npoYtcYt[ bt]utoYts.
i. Press the appropriate component button (DVI) or A[]X) to set the remote to control the
coi77pol]e_lt.
2. Press (])N,_(])VV "to "turn "the component ON or (])VF.
3. Use the remote buttons that apply to that component
Notes: 7_)e n'm, ote cont*'cU ,wg<p*?()t be (7o,_q)cTtihT(>_(,iU) a77,bF.,_?d._a*Td ,,wod('7._oj"
COlt;/_O;TC';ILs.
,J[yoTl/_o('p/)n'.<sin<k bltMo*Ts a*Td no!_?in<k_?(s[>l'_m*7.s.U?e *vs,>_o/ei.sp1"o+Oab{yi_7 U?P_1"on<k
t7;0C7('. }2>H M;ILSi 191"(<<%li:?e COI?TtgoHe;7I blHIOH t/047I t;';471C_?('.% li:?e COI'tT/)O;IP;H .yOZ7 ZP_7;7I ZO
()iJCt77/O ( 7.g. (I'.]17)77 Z_'<7;H t77 (.[iJ(qZH( > l_?( > DI 'I') /JT((]i(>I; /7F(><'; /)I 's') 7717 If?( > 7"(>Ml()/O ('()H/I'07 /77/77H
li:?e E(>S770!P 717 /)I 'L) 1HOd7(>.)
23