SMART Signage TV User Manual RM40D RM48D The color and the appearance may differ depending on the product, and the specifications are subject to change without prior notice to improve the performance. Recommended hours of use per day of this product is under 16 hours. If the product is used for longer than 16 hours a day, the warranty may be void.
Table of contents Before Using the Product Copyright 5 Safety Precautions Symbols Cleaning Storage Electricity and Safety Installation Operation 6 6 6 7 7 8 10 Preparations Connecting and Using a Source Device Before Connecting Pre-connection Checkpoints 26 26 Connecting to a PC Connection Using an HDMI Cable Connection Using an HDMI-DVI Cable 27 27 27 Connecting to a Video Device Connection Using the AV Cable Connection Using an HDMI-DVI Cable Connection Using an HDMI Cable 28 28 29 29 Connectin
Table of contents Sound Adjustment Caption Caption 62 62 Sound Mode 45 Sound Effect 46 Speaker Settings 47 Network Reset Sound 48 Network Status 64 Network Settings Network Setting (Wireless) WPS(PBC) 64 65 67 Soft AP (Wi-Fi Hotspot) 68 Wi-Fi Direct 69 AllShare Settings 70 Device Name 70 Broadcasting Auto Program 49 Antenna 50 Channel List Mode 51 51 Schedule Manager 52 Edit Channel 53 Edit Favorites 55 Channel Settings Fine Tune Clear Scrambled Channel 58 58 58 Audio O
Table of contents Time Clock Sleep Timer On Timer Holiday Management 90 90 91 91 93 Eco Solution Energy Saving Eco Sensor No Signal Power Off Auto Power Off 94 94 94 95 95 Auto Protection Time 96 Screen Burn Protection Pixel Shift Timer Immediate Display Side Gray Clone Product 106 Reset System 106 Reset All 107 DivX® Video On Demand 107 Support General 119 Power Consumption 121 Preset Timing Modes 122 Appendix Software Update Update now 108 108 97 97 98 100 100 Use Mode 108 Cont
Chapter 01 Before Using the Product Copyright The contents of this manual are subject to change without notice to improve quality. © 2014 Samsung Electronics Samsung Electronics owns the copyright for this manual. Use or reproduction of this manual in parts or entirety without the authorization of Samsung Electronics is prohibited. Microsoft, Windows are registered trademarks of Microsoft Corporation. VESA, DPM and DDC are registered trademarks of the Video Electronics Standards Association.
Safety Precautions Cleaning ――Exercise care when cleaning as the panel and exterior of advanced LCDs are easily scratched. Caution ――Take the following steps when cleaning. ――The following images are for reference only. Real-life situations may differ from what is shown in the images. RISK OF ELECTRIC SHOCK DO NOT OPEN Caution : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. (OR BACK) THERE ARE NO USER SERVICEABLE PARTS INSIDE. REFER ALL SERVICING TO QUALIFIED PERSONNEL.
Storage Connect the power plug to a grounded power socket (type 1 insulated devices only). Due to the characteristics of high-glossy products, using a UV humidifier nearby may create whitecolored stains on the product. ――Contact Customer Service Center if the inside of the product needs cleaning (service fee will be •• An electric shock or injury may result. ! Do not bend or pull the power cord with force. Be careful not to leave the power cord under a heavy object. charged).
Installation Caution Do not disconnect the power cord while the product is being used. •• The product may become damaged by an electric shock. Warning DO NOT PLACE CANDLES, INSECT REPELLANTS OR CIGARETTES ON TOP OF THE PRODUCT. DO NOT INSTALL THE PRODUCT NEAR HEAT SOURCES. •• A fire may result. Only use the power cord provided with your product by Samsung. Do not use the power cord with other products. •• A fire or electric shock may result. Have a technician install the wall-mount hanger.
Bend and keep part of the outdoor TV antenna cable hanging downwards (the part inside the room) to prevent rainwater from entering the product. Edible oil, such as soybean oil, can damage or deform the product. Do not install the product in a kitchen or near a kitchen counter. •• If rainwater enters the product, a fire or electric shock can occur. ! When using an outdoor antenna, be sure to install the antenna away from nearby power lines to prevent the antenna from collapsing onto them in strong winds.
Operation Caution Do not drop the product while moving. •• Product failure or personal injury may result. Warning There is a high voltage inside the product. Never disassemble, repair or modify the product yourself. ! •• A fire or electric shock may result. Do not set down the product on its front. •• Contact Samsung Customer Service Center for repairs. •• The screen may become damaged.
Do not leave heavy objects or items that children like (toys, sweets, etc.) on top of the product. Do not use or keep combustible spray or an inflammable substance near the product. •• The product or heavy objects may fall as children try to reach for the toys or sweets resulting in a serious injury. •• An explosion or fire may result. ! During a lightning or thunderstorm, remove the power cable and do not touch the antenna cable. Ensure the vents are not blocked by tablecloths or curtains.
Caution Rest your eyes for more than 5 minutes for every 1 hour of product use. •• Eye fatigue will be relieved. Leaving the screen fixed on a stationary image for an extended period of time may cause afterimage burn-in or defective pixels. •• Activate power-saving mode or a moving-picture screen saver if you will not be using the product for an extended period of time. ! Do not touch the screen when the product has been turned on for an extended period of time as it will become hot.
Be careful that children do not place the battery in their mouths when removed from the remote control. Place the battery in a location that children or infants cannot reach. •• If children have had the battery in their mouths, consult your doctor immediately. When replacing the battery, insert it with the right polarity (+, -). •• Otherwise, the battery may become damaged or it may cause fire, personal injury or damage due to leakage of the internal liquid.
Chapter 02 Preparations Checking the Components -- Contact the vendor where you purchased the product if any components are missing. -- The appearance of the components and items sold separately may differ from the image shown. Components ――Components may differ in different locations.
Items sold separately -- The following items can be purchased at your nearest retailer.
――The color and shape of parts may differ from what is shown. Parts Specifications are subject to change without notice to improve quality. Panel Key Control Panel Buttons Description Power on the product. If you press the button when the product is turned on, the control menu will be displayed. ――To exit the OSD menu, press and hold the panel key for at least one second. POWER Move to the upper or lower menu. You can also adjust the value of an option. Change the channel in TV mode.
――If you press the button on the panel key when the product is turned on, the control menu will be displayed. Buttons Description Select the connected input source. Control menu Source Move the panel key right to select Source in the control menu. When the list of input sources is displayed, move the panel key up or down to select the desired input source. Next, press the panel key. Display the OSD menu. Menu MagicInfo in the control menu.
Reverse Side Port ――The color and shape of parts may differ from what is shown. HDMI IN 1 (STB), HDMI IN 2 (DVI) Connects to a source device using a HDMI cable or HDMI-DVI cable. USB Connect to a USB memory device. Specifications are subject to change without notice to improve quality. HDMI IN 2 (DVI) HDMI IN 1 (STB) Description (5V 0.5A) / CLONING AV IN VIDEO / L-AUDIO-R Connect to an external device using a video or Audio cable.
Anti-theft Lock ――An anti-theft lock allows you to use the product securely even in public places. ――The locking device shape and locking method depend on the manufacturer. Refer to the user guide provided with your anti-theft locking device for details. ――The following images are for reference only. Real-life situations may differ from what is shown in the images. To lock an anti-theft locking device: 1 Fix the cable of your anti-theft locking device to a heavy object such as a desk.
Remote Control ――Using other display devices in the same space as the remote control of this product can cause the other display devices to be inadvertently controlled. ――A button without a description in the image below is not supported on the product. POWER OFF Turns the product On/Off. .QZ ABC DEF GHI JKL MNO PRS TUV WXY DEL-/-- SYMBOL 1 4 Press to select additional channels (digital) being broadcasted by the same station.
Quickly select frequently used functions. TOOLS INFO Display information about the current input source. Move to the upper, lower, left or right menu, or adjust an option's setting. Confirm a menu selection. Return to the previous menu. It sets safe lock function. Not Available. RETURN EXIT PC DVI HDMI DP A B C D UNSET LOCK IR control SET Exit the current menu. In TV mode, configure settings such as the program guide for digital channels.
Before Installing the Product (Installation Guide) To prevent injury, this apparatus must be securely attached to the floor/wall in accordance with the installation instructions. •• Ensure that an authorized installation company installs the wall mount. •• Otherwise, it may fall and cause personal injury. •• Make sure to install the specified wall mount. Tilting Angle and Rotation 15 ˚ ――Contact Samsung Customer Service Center for further details.
Figure 1.3 Side view Installation on an Indented Wall ――Contact Samsung Customer Service Center for further details. B D D Plane view A Minimum 40 mm B Minimum 70 mm A C Minimum 50 mm D Minimum 50 mm E Ambient temperature: Under 35 C ――When installing the product on an indented wall, allow at least the space specified above between the product and wall for ventilation and ensure that the ambient temperature is kept below 35 C. C E Figure 1.
Installing the Wall Mount Installing the Wall Mount Kit The wall mount kit (sold separately) allows you to mount the product on the wall. For detailed information on installing the wall mount, see the instructions provided with the wall mount. We recommend you contact a technician for assistance when installing the wall mount bracket. Samsung Electronics is not responsible for any damage to the product or injury to yourself or others if you elect to install the wall mount on your own.
Wall Mount Kit Specifications ――Install your wall mount on a solid wall perpendicular to the floor. Before attaching the wall mount to surfaces other than plaster board, please contact your nearest dealer for additional information. If you install the product on a slanted wall, it may fall and result in severe personal injury. •• Samsung wall mount kits contain a detailed installation manual and all parts necessary for assembly are provided.
Chapter 03 Connecting and Using a Source Device Before Connecting Pre-connection Checkpoints ――Before connecting a source device, read the user manual provided with it. The number and locations of ports on source devices may differ from device to device. ――Do not connect the power cable until all connections are completed. Connecting the power cable during connection may damage the product. ――Connect the sound ports correctly: left = white and right = red.
Connecting to a PC •• Do not connect the power cable before connecting all other cables. Ensure you connect a source device first before connecting the power cable. •• A PC can be connected to the product in a variety of ways. Select a connection method suitable for your PC. ――Connecting parts may differ in different products. Connection Using an HDMI Cable Connection Using an HDMI-DVI Cable ――Audio is not available if the PC and product are connected via the HDMI-DVI port.
Connecting to a Video Device •• Do not connect the power cable before connecting all other cables. Ensure you connect a source device first before connecting the power cable. •• You can connect a video device to the product using a cable. ――Connecting parts may differ in different products. ――Press the SOURCE button on the remote control to change the source.
Connection Using an HDMI-DVI Cable ――Audio will not be enabled if the product is connected to a video device using an HDMI-DVI cable. To resolve this, additionally connect an audio cable to the audio ports on the product and video device. When you connect a video device to the product using an HDMI-DVI cable, set Edit Name to DVI Devices to access video and audio content stored on the video device. ――Supported resolutions include 1080p (50/60Hz), 720p (50/60Hz), 480p, and 576p.
Connecting to an Audio System Connecting the Antenna ――Connecting parts may differ in different products. ――Connecting parts may differ in different products. ――When the product is powered on for the first time, basic settings are configured automatically. ――Take extra care to ensure the wires inside the antenna cable are not bent.
Initial Setup After powering on the product for the first time, configure basic settings such as the language, channel and time. Language → Regional Settings → Channel Source→ (Auto Program if the Channel Source is Antenna) → Network Settings → Clock → Setup Complete! ――Refer to page 87 for details about the Setup. Changing the Input source Source allows you to select a variety of sources and change source device names.
Chapter 04 Screen Adjustment Configure the Picture settings (Backlight, Color Tone, etc.). -- The layout of the Picture menu options may vary depending on the product. Picture Mode If the input source is HDMI1 (when a PC is connected), HDMI2 (when a PC is connected), HDMI3 (when a PC is connected) MENU m → Picture → Picture Mode → ENTER E •• Information: This mode reduces eye fatigue and is suitable for displaying information to the public.
Backlight / Contrast / Brightness / Sharpness / Color / Tint (G/R) MENU m → Picture → ENTER E Picture Picture Mode Information · Backlight 55 · Contrast 100 · Brightness 45 · Sharpness 50 · Color 50 · Tint (G/R) G50 Your product has several options for adjusting picture quality.
Picture Size choose size and aspect ratio picture displayed on screen. Picture Size MENU m → Picture → Picture Size → ENTER E ――Different Screen Adjustment options are displayed depending on the current input source. •• 16:9: Sets the picture to 16:9 wide mode. Picture Size Picture Size · Position •• Zoom1: Use for moderate magnification. Cuts off the top and sides. 16:9 •• Zoom2: Use for a stronger magnification. •• Smart View 1: Reduces the 16:9 picture by 50%.
Picture Sizes available by Input Source.
Position Adjusts the picture position. Position is only available if Picture Size is set to Zoom1, Zoom2, Wide Fit or Screen Fit. ――To use the Position function after selecting Zoom1, Zoom2, Wide Fit or Screen Fit, follow these steps. Picture Size Picture Size Zoom1 · Position 1 Press the button to select Position. Press the E button. 2 Press the or 3 Press the E button. button to move the picture up or down.
PIP MENU m → Picture → PIP → ENTER E Picture PIP PIP Settings The picture from the external video source will be in the main screen and the picture from the product will be in the PIP subpicture screen. Main picture Sub picture AV, TV HDMI1, HDMI2, HDMI3 HDMI1, HDMI2, HDMI3 AV, TV •• PIP (Off / On): Activate or deactivate the PIP function. •• Source: You can select a source of the sub picture. -- The displayed image may differ depending on the model.
Advanced Settings Input Source MENU m → Picture → Advanced Settings → ENTER E Advanced Settings Dynamic Contrast Medium Black Tone Off Flesh Tone 0 RGB Only Mode Color Space Off Picture Mode Advanced Settings HDMI1 (when a PC is connected), HDMI2 (when a PC is connected), HDMI3 (when a PC is connected) Information, Advertisement White Balance / Gamma TV, HDMI1, HDMI2, HDMI3, AV Dynamic Not available.
Dynamic Contrast Advanced Settings Dynamic Contrast Medium Black Tone Off Flesh Tone 0 RGB Only Mode Color Space Off Native White Balance Gamma 0 Adjust the screen contrast. •• Off / Low / Medium / High Black Tone Select the black level to adjust the screen depth. •• Off / Dark / Darker / Darkest Flesh Tone Emphasize pink Flesh Tone. RGB Only Mode Displays the Red, Green and Blue color for making fine adjustments to the hue and saturation.
White Balance Advanced Settings Adjust the color temperature for a more natural picture. White Balance Gamma Motion Lighting 2 Point 0 Off •• R-Offset / G-Offset / B-Offset: Adjust each color’s (red, green, blue) darkness. •• R-Gain / G-Gain / B-Gain: Adjust each color’s (red, green, blue) brightness. •• Reset: Resets the White Balance to its default settings. -- The displayed image may differ depending on the model. Gamma Adjust the primary color intensity.
Picture Options Select an option using the and arrow keys, the press E. Use the arrow keys to change the setting, and then press E. MENU m → Picture → Picture Options → ENTER E Picture Options Color Tone Color Temp.
Color Tone Picture Options Color Tone Color Temp. Off 10000K Digital Clean View Off MPEG Noise Filter Off If the input source is HDMI1 (PC connection), HDMI2 (PC connection), HDMI3 (PC connection). •• Off / Cool / Standard / Warm If the input source is AV, HDMI1, HDMI2, HDMI3 or TV. •• Off / Cool / Standard / Warm1 / Warm2 ――Warm1 or Warm2 will be deactivated when the Picture Mode is Dynamic. ――Settings can be adjusted and stored for each external device connected to an input on the product.
HDMI Black Level Picture Options Selects the black level on the screen to adjust the screen depth. HDMI Black Level Normal Film Mode Off Dynamic Backlight Off •• Normal / Low ――Available only in HDMI1 (PC connection), HDMI2 (PC connection), HDMI3 (PC connection) mode (Enabled only when the color format is RGB.). Film Mode This mode is suitable to view movies. -- The displayed image may differ depending on the model.
Picture Off Selecting Picture Off switches off the screen. The volume is not disabled. To switch the screen on, press any button other than the volume button. MENU m → Picture → Picture Off → ENTER E Picture Picture Off -- The displayed image may differ depending on the model. Reset Picture Resets your current picture mode to its default settings. MENU m → Picture → Reset Picture → ENTER E Picture Reset Picture -- The displayed image may differ depending on the model.
Chapter 05 Sound Adjustment Configure the sound (Sound) settings for the product. Sound Mode You can select a sound mode to suit your personal preferences. •• Standard: Selects the normal sound mode. MENU m → Sound → Sound Mode → ENTER E •• Movie: Provides the best sound for movies. •• Clear Voice: Emphasizes voices over other sounds. Sound Sound Mode •• Music: Emphasizes music over voices.
Sound Effect MENU m → Sound → Sound Effect → ENTER E Sound Sound Effect Configure your preferred sound effect for output sound. ――If Speaker Select is set to External, Sound Effect is disabled. ――Available only when Sound Mode is set to Standard. •• DTS TruSurround HD (Off / On) This function provides a virtual 5.1 channel surround sound experience through a pair of speakers using HRTF(Head Related Transfer Function) technology.
Speaker Settings MENU m → Sound → Speaker Settings → ENTER E Sound •• Speaker Select (External / Internal) If you are listening to the sound track of a broadcast or movie through an external receiver, you may hear a sound echo caused by the difference in decoding speed between the products speakers and the speakers attached to your audio receiver. If this occurs, set the product to External. ――When you set Speaker Select to External, the products speakers are turned off.
Reset Sound Reset all sound settings to the factory defaults. MENU m → Sound → Reset Sound → ENTER E Sound Reset Sound -- The displayed image may differ depending on the model.
Chapter 06 Broadcasting Configure the Broadcasting settings for the product. Auto Program The Auto Program function memorizes all channels that are available over the air or through your cable system and adds them to the Channel List. To start Auto Program, follow these steps: MENU m → Broadcasting → Auto Program → ENTER E Broadcasting 1 Push MENU m → Broadcasting → Auto Program → ENTER E on your remote. The Auto Program screen appears.
Antenna Before your television can begin memorizing the available channels, you must specify the type of signal source that is connected to the LED display. •• Air / Cable MENU m → Broadcasting → Antenna → ENTER E Broadcasting Antenna Cable -- The displayed image may differ depending on the model. -- Available in TV mode only.
Channel List MENU m → Broadcasting → Channel List → ENTER E Register or delete channels. Add favorite channels or rename analog channels. Select a desired channel from Channel List to view the channel instantly. ――To navigate Channel List faster, press the channel buttons. The channel list changes page by page.
Schedule Manager MENU m → Broadcasting → Schedule Manager → ENTER E Broadcasting Watch a desired channel at a scheduled time. •• Antenna: DTV Cable / Cable •• Channel: Select the desired channel. •• Repeat: Once / Manual / Sat~Sun / Mon~Fri / Everyday ――Select Manual if you want to configure settings by day of the week. •• Date: Select the desired date. •• Start Time: Set the time to watch the desired channel. Schedule Manager -- The displayed image may differ depending on the model.
Edit Channel Manage channels saved on your TV. Delete channels, re-register deleted channels or rename analog channels. ――Conveniently configure settings using the remote control buttons displayed at the bottom of the screen.
Editing registered channels Locking/unlocking channels using a password Pressing TOOLS from the Edit Channel page displays the following menu items. Provided functions may vary depending on the broadcast signal. Lock specific channels to prevent children from accessing inappropriate content. ――To set a password, make sure Program Rating Lock is set to On. Option Name Operations Antenna Select either Air or Cable as digital channel mode.
Edit Favorites MENU m → Broadcasting → Edit Favorites → ENTER E Broadcasting Edit Favorites -- The displayed image may differ depending on the model. -- Available in TV mode only. Creating a favorite channel list Set frequently viewed channels as favorite channels. Favorite channels are indicated by a symbol in the Edit Channel or Channel List page. A maximum of five favorite channel lists are allowed. Create different favorite channel lists for each family member.
Viewing channels saved under a favorite channel list Deleting channels from a favorite channel list ――Favorite channel lists are only displayed if they have been created previously. Delete channels from a favorite channel list, if required. When changing the channel using the channel buttons, channels saved in favorite channel lists can only be accessed. 1 1 Select Channel List from the Channel menu. The channel list is displayed.
Renaming a favorite channel list Change the name of a favorite channel list, if required. 1 Select Change Fav. from the screen to change the favorite channel list on the right to another desired favorite channel list. 2 Press TOOLS on the screen. Sub-menu items are displayed. 3 Select Rename Favorites from the sub-menu items. A prompt box appears. 4 Change the favorite channel list using the prompt box. The name for a favorite channel list can be up to 20 characters long.
Channel Settings Fine Tune (analog channels only) MENU m → Broadcasting → Channel Settings → ENTER E Broadcasting If the reception is clear, you do not have to fine tune the channel, as this is done automatically during the search and store operation. If the signal is weak or distorted, fine tune the channel manually. Scroll to the left or right until the image is clear. ――This function is only available in Cable mode. ――Settings are applied to the channel you’re currently watching.
Audio Options Preferred Language (for digital broadcasts) MENU m → Broadcasting → Audio Options → ENTER E Digital-TV broadcasts can simultaneously transmit many audio tracks (for example, simultaneous translations of the program into foreign languages). ――You can only select a language from among the ones being broadcasted. Audio Options Preferred Language Multi-Track Sound Use the up and down arrow keys to select a language, and then press E.
Program Rating Lock When turned on, the Program Rating Lock feature can automatically block programs that you deem inappropriate for your children. You must enter a PIN (personal identification number) before you can set or change any of the Program Rating Lock restrictions. MENU m → Broadcasting → Program Rating Lock → ENTER E •• Off / On ――This option is available when the input source is TV. ――The default PIN number for a new product set is “0-0-0-0”.
•• Canadian English Rating: You can block TV programs based on their Anglophone Canadian rating. Canadian English Rating displays a column with locks and the following ratings categories. C: Programming intended for children under age 8. / C8+: Programming generally considered acceptable for children 8 years and over to watch on their own. / G: General programming, suitable for all audiences. / PG: Parental Guidance.
Caption Caption You can switch the caption function on or off. MENU m → Broadcasting → Caption → ENTER E Broadcasting Caption If captions are not available, they will not be displayed on the screen. •• Off / On ――The Caption feature does not work with devices connected to the product through the HDMI1, HDMI2, HDMI3 input jacks. Caption Mode You can select the desired caption mode. ――The availability of captions depends on the program being Broadcasted.
Digital Caption Options (digital channels only) Configure the subtitle settings such as size and color. Adjusts the each option. When done, select Close. •• Size: Options include Default, Small, Standard and Large. The default is Standard. •• Font Style: Select the caption fonts. •• Font Color: You can change the color of the letters. Options include Default, White, Black, Red, Green, Blue, Yellow, Magenta and Cyan. The default is White.
Chapter 07 Network Network Status Network Settings MENU m → Network → Network Status → ENTER E MENU m → Network → Network Settings → ENTER E You can check the current network and Internet status. Connect to a wireless network and use the product as a TV+signage using MagicInfo Express Content Creator on your PC. Network Status Your wireless network and Internet connection are setup and ready to use. MAC Address IP Address Subnet Mask Gateway DNS Server AP0000 ***. ***. ***. ***. ***. ***. ***.
Network Setting (Wireless) Connecting to a Wireless Network Automatic Network Setup (Wireless) Most wireless networks have an optional security system that requires devices that access the network to transmit an encrypted security code called an Access or Connection Information. The Connection Information is based on a Pass Phrase, typically a word or a series of letters and numbers of a specified length you were asked to enter when you set up security for your wireless network.
6 When done, use the down arrow button to move the cursor to Done, and then press E. The How to set up manually network connection screen appears and the verification process starts. On the SMART Signage TV, go to MENU m → Network → Device Name and change the SMART Signage TV's device name. ――If you use multiple SMART Signage TVs, make sure to change their device names. ――A connection with the router is established, but the Internet cannot be accessed.
10 When done, select OK at the bottom of the page, and then press E. The network test screen appears and the verification process starts. 11 When the connection has been verified, the “Your wireless network and Internet connection are setup and ready to use.” message appears. WPS(PBC) How to set up using WPS(PBC) If your router has a WPS(PBC) button, follow these steps. 1 Go to MENU m → Network → Network Settings. 2 Select WPS(PBC), press E, and then press E again.
Soft AP (Wi-Fi Hotspot) To use this function, your mobile device should be supported by the Wi-Fi Direct. MENU m → Network → Soft AP (Wi-Fi Hotspot) → ENTER E Using this function, you can connect the product on your mobile devices if your mobile devices do not support Wi-Fi Direct. Set the options for connection of Wi-Fi device. •• Soft AP (Wi-Fi Hotspot) Turns on or off the Soft AP (Wi-Fi Hotspot).
Wi-Fi Direct MENU m → Network → Wi-Fi Direct → ENTER E Set to connect the product to wireless mobile devices. Using this function, you can connect wireless mobile devices with your product directly without a router. To connect your mobile device with your product using Wi-Fi Direct, follow these steps: 1 Go to Wi-Fi Direct screen. The product starts to search devices. 2 Turn on the Wi-Fi Direct function on your device. Select the desired Wi-Fi device.
AllShare Settings MENU m → Network → AllShare Settings → ENTER E Shows a list of mobile phones or connected devices which have been set up to use the AllShare Play function with this product. •• Allow / Deny: Allows/Blocks the devices. •• Delete from the list: Deletes the devices from the list. ――This function only deletes the name of the device from the list. If the deleted device is turned on or tries to connect to the product, it may appear on the list again.
Chapter 08 Applications Source List Source allows you to select a variety of sources and change source device names. MENU m → Applications → Source List → ENTER E You can display the screen of a source device connected to the product. Select a source from source list to display the screen of the selected source. ――The input source can also be changed by using the SOURCE button on the remote control.
MagicInfo MENU m → Applications → MagicInfo → ENTER E Applications MagicInfo MagicInfo is a business solution that allows the product to be used as a signage (advertising media). Using the solution, play image and video files from the internal memory or a connected USB storage device. You can also play schedules created using the MagicInfo Express Content Creator on your computer. Playing content from the internal memory or USB Play content from the internal memory or a connected USB storage device.
Device : All Content : All Sort by : File Name Options Schedule Play configured schedules. Schedule Available features in the MagicInfo page The MagicInfo list page provides the following features. •• Device -- Select either Internal Memory or USB to search for a desired device list. All / Internal Memory / USB -- The displayed image may differ depending on the model. •• Content -- Select a content type as criterion to search for a desired content list.
Settings Default Storage Select the storage location that you want to download scheduled channels from the network to. Settings •• Internal Memory / USB Select the storage location that you want to download scheduled channels from the network to. Default Storage Repeat Mode Repeat Mode Set repeat mode whether to repeat playing contents or not.
Chapter 09 MagicInfo Express Content Creator Refer to the MagicInfo Express Content Creator guide found in the user guide USB for details. Installation requirements Using MagicInfo Express Content Creator -- HDD: At least 500 MB of free space -- Operating system: Windows XP or later -- Resolution: 1024x738 or higher MagicInfo Express Content Creator is a program that allows you to conveniently create SMART Signage TV content using a variety of templates.
Chapter 10 Playing photos, videos and music (Media Play) Enjoy videos, photos, music files saved on a USB Mass Storage Class (MSC) device. Play photos, videos or music saved on a storage device. Play a variety of content using the following methods. •• Using a USB device: Play media content such as videos, photos and music from a USB device. •• Connecting a storage device: Play media content saved on a storage device such as a smartphone, camera, PC or cloud service.
Compatible devices with media play •• Some USB digital cameras, smartphones and audio devices may not be compatible with the product. •• Media play is only compatible with USB MSC devices. •• MSC device refers to a Mass Storage Class Bulk-Only Transport device. Examples of MSC devices include Thumb drives, Flash card readers and USB HDDs. (USB hubs are not supported.) These MSC devices must be connected directly to a USB port on the product.
Using a USB device It is recommended to use a USB HDD that has a power adapter. Connecting a USB device 1 Turn on your product. 2 Connect a USB device containing photo, music and/or movie files to the USB port on the back or side panel of the product. 3 The New device connected. page automatically appears as soon as a USB device connects to the product. ――If only one USB device is connected, files saved on the USB device are displayed automatically.
Menu items in the media content list page Option Name Operations Slide Show Start a slideshow. ――This menu item is not available if Sort by is set to Folder. Encoding Select an encoding language if the title of media content appears corrupted. Play Selected Select and play desired content from the media content list.
Available buttons and features during photo playback Pressing the E or TOOLS button displays the following buttons. The RETURN button makes the buttons disappear. Pressing the INFO button while a file is selected will display information about the selected file. •• Previous / Next View the previous or next photo. •• Start Slide Show / Stop Slide Show Start or stop a slideshow. Using a slideshow, it is possible to play all photos in a folder. •• Slideshow Settings -- Speed: Change the slideshow speed.
Available buttons and features during video playback Pressing the E or TOOLS button displays the following buttons. The RETURN button makes the buttons disappear. •• Pause / Play Pause or play a video. The following features are available in pause mode. Note that sound cannot be heard in pause mode. Option Name Operations Picture Mode Change the Picture Mode. Sound Mode Change the Sound Mode. Audio Language Play a video using a desired language.
Available buttons and features during music playback Pressing the E or TOOLS button displays the following buttons. The RETURN button makes the buttons disappear. •• Pause / Play Pause or play music. •• Rewind / Fast forward Rewind or fast forward music. Speed up playback up to 3x, if required. To play the previous music file, select ∂ twice. •• Previous / Next To play the previous music file, select twice. Selecting once will play the current music from the beginning.
Supported Subtitle and Media play file formats Subtitle External •• MPEG-4 timed text (.ttxt) •• SAMI (.smi) •• SubRip (.srt) •• SubViewer (.sub) •• Micro DVD (.sub or .txt) •• SubStation Alpha (.ssa) •• Advanced SubStation Alpha (.ass) •• Powerdivx (.
Supported music file formats File Extension *.aac, *.flac, *.m4a, *.mid, *.midi, *.mp3, *.mpa, *.ogg, *.wav, *.wma Supported Video Formats •• Video content will not play, or not play correctly, if there is an error in the content or the container. •• Sound or video may not work if the contents have a standard bitrate/frame rate above the compatible Frame/sec listed in the table above. •• If the Index Table is in error, the Seek (Jump) function is not supported.
Container Video Codec Resolution Frame rate (fps) Bit rate (Mbps) Audio Codec 3gpp DivX 3.11 /DivX4.X 1280 x 720 60 30 AAC asf avi flv mkv mov AC3 XVID H.264 BP/MP/HP MPEG-4 SP/ASP mp4 ps vro DD+ DTS Core HE-AAC LPCM WINDOW MEDIA VIDEO V9 ts vob ADPCM MP3 WMA MPEG2 MPEG1 H.263 DivX5.x DivX6.
Container Video Codec Resolution Frame rate (fps) Bit rate (Mbps) Audio Codec 3gpp DivX 3.11 /DivX4.X 1920 x 1080 30 30 AAC asf avi flv mkv mov mp4 AC3 XVID ADPCM DD+ H.264 BP/MP/HP DTS Core MPEG-4 SP/ASP HE-AAC LPCM WINDOW MEDIA VIDEO V9 ps ts vob MP3 MPEG2 WMA MPEG1 vro H.263 DivX5.x DivX6.
Chapter 11 System Setup Initial settings (Setup) After powering on the product for the first time, configure basic settings such as the language, channel and time. MENU m → System → Setup → ENTER E Press the 1 System Selecting a language Press the 2 Setup Menu Language button. Setup is available only when Source is set to TV. English Configure the TV settings. Set Channel Source to Set-top box to display the Source options.
6 Clock Set the current date and time, and then select Next. 7 Setup Complete! To watch TV using the product now, select OK.
Menu Language Set the menu language. ――A change to the language setting will only be applied to the onscreen menu display. It will not be applied to other functions on your PC. MENU m → System → Menu Language → ENTER E System Menu Language English -- The displayed image may differ depending on the model.
Time You can configure Clock. You can also set the product to automatically turn on or off at a specified time using the Timer function. MENU m → System → Time → ENTER E Clock Time Clock Mode Set the current time manually or automatically. Clock Sleep Timer On Timer Off Timer Holiday Management Off Auto: Have the product set the current time automatically using the time from a digital channel. ――You must have the cable or an antenna connected to the product to set the time automatically.
Time Zone Select your time zone. ――This function is only available when the Clock Mode is set to Auto. Time Offset Select the correct time offset your timezone. ――This function is only available when the Clock Mode is set to Auto. Sleep Timer Automatically shuts off the product after a preset period of time. (Off / 30 min. / 60 min. / 90 min. / 120 min. / 150 min. / 180 min.) ――Use the up and down arrows to select a period of time, and then press E. To cancel Sleep Timer, select Off.
――This function is available only when a USB device is connected. ――If there is no music file on the USB device or you don’t select a folder containing a music file, the Timer function does not operate correctly. ――If there is only one photo file in the USB, the Slide Show will not play. ――If a folder name is too long, the folder cannot be selected. ――Each USB you use is assigned its own folder.
Off Timer Set the off timer (Off Timer) by making a selection from one of the seven options. (Off Timer1 ~ Off Timer7) ――You must set the clock before you can use Off Timer. •• Setup: Select Off, Once, Everyday, Mon~Fri, Mon~Sat, Sat~Sun or Manual. If you select Manual, you can choose the days you want Off Timer to turn off your product. ――The check mark indicates days you’ve selected. •• Time: Set the hour and minute. Use the number buttons or the up and down arrow keys to enter numbers.
Eco Solution Energy Saving Reduce the power consumption by adjusting the screen brightness. MENU m → System → Eco Solution → ENTER E Selecting Picture Off switches off the screen. The volume is not disabled. To switch the screen on, press any button other than the volume button. Eco Solution •• Off / Low / Medium / High Energy Saving Off Eco Sensor Off No Signal Power Off 15 min. Auto Power Off -- The displayed image may differ depending on the model.
No Signal Power Off Eco Solution Save power by turning the device off when no signal is received from any source. Energy Saving Off Eco Sensor Off No Signal Power Off •• Off / 15 min. / 30 min. / 60 min. ――Disabled when an attached PC is in power saving mode. ――The product will automatically power off at a specified time. The time can be changed as required. 15 min.
Auto Protection Time If the screen displays a still image for a certain period of time you define, the product activates the screen saver to prevent the formation of burnt in ghost images on the screen. ――Displaying a still image for longer than four hours can cause image retention. MENU m → System → Auto Protection Time → ENTER E •• Off / 2 hours / 4 hours / 8 hours / 10 hours System Auto Protection Time Off -- The displayed image may differ depending on the model.
Screen Burn Protection MENU m → System → Screen Burn Protection → ENTER E To reduce the possibility of screen burn, this unit is equipped with Pixel Shift screen burn prevention technology. Pixel Shift moves the picture slightly on the screen. The Pixel Shift Time setting allows you to program the time between movements of the picture in minutes. Pixel Shift Screen Burn Protection Minimize image retention by finely moving pixels horizontally or vertically.
Timer Screen Burn Protection You can set the timer for Screen Burn Protection. Pixel Shift Off The Timer feature stops automatically after a specified period of time. Timer Off Timer Immediate Display Off •• Off Side Gray Off •• Repeat: Display the image retention-preventive pattern set in Mode at specified time intervals(Period). •• Interval: Display the image retention-preventive pattern set in Mode for a specified period of time (from Start Time to End Time).
Start Time Set the start time to activate the screen protection function. ――The option is enabled when Interval is selected for Timer. End Time Set the end time to deactivate the screen protection function. ――The option is enabled when Interval is selected for Timer.
Immediate Display Screen Burn Protection Select the screen saver you want to display immediately. Pixel Shift Off Timer Off Immediate Display Off Side Gray Off •• Off / Pixel / Rolling Bar / Fading Screen Side Gray When the screen is set to 4:3 aspect ratio, adjust the brightness of white margins on sides to protect the screen. •• Off / Right / Dark -- The displayed image may differ depending on the model.
Ticker Ticker Input text while a video or image is displayed and display the text on the screen. MENU m → System → Ticker → ENTER E •• Off / On ――Message, Time, Position, Motion, and Font Options are enabled only when Ticker is set to On. Ticker Ticker Message Off · Message Time · Time Set the Start Time and End Time to display a Message. •• Start Time · Position · Motion Enter a message to display on the screen.
Source AutoSwitch Settings Turning on the display with Source AutoSwitch On, and the previous video source selection is not active, the display will automatically search the different video input sources for active video. MENU m → System → Source AutoSwitch Settings → ENTER E Source AutoSwitch When the Source AutoSwitch is On, the display video source will automatically be searched for active video.
Change PIN MENU m → System → Change PIN → ENTER E The Change PIN screen will appear. Choose any 4 digits for your PIN and enter it in Enter New PIN. Reenter the same 4 digits in Confirm New PIN. When the Confirm screen disappears, press the Close button. The product has memorized your new PIN. ――Default password: 0 - 0 - 0 - 0 System Change PIN -- The displayed image may differ depending on the model.
General Game Mode When connecting to a game console such as PlayStation™ or Xbox™, you can enjoy a more realistic gaming experience by selecting game mode. MENU m → System → General → ENTER E •• Off / On ――Precautions and limitations for Game Mode General To disconnect the game console and connect another external device, set Game Mode to Off in the setup menu.
Button Lock General It sets safe lock function. Button Lock Off Standby Control Auto Lamp Schedule Off OSD Display •• Off / On This menu can be used to lock the buttons on the product. Only the remote control can control the product if Button Lock is set to On. Standby Control You can set the screen standby mode to be applied when an input signal is received. •• Auto Power-saving mode will activate if no input signals are detected even though a source device is connected to the display.
Clone Product MENU m → System → Clone Product → ENTER E Clone Product Clone to USB Clone From USB Export the product settings to a USB device or load the settings via a USB device. This option is useful when assigning the same settings to several products. •• Clone to USB: Copy the product settings to a USB device. •• Clone From USB: Assign the settings saved in a USB device to the product. -- After configuration is complete, the product is rebooted automatically.
Reset All This option returns all the current settings for a display to the default factory settings. MENU m → System → Reset All → ENTER E System Reset All -- The displayed image may differ depending on the model. DivX® Video On Demand MENU m → System → DivX® Video On Demand → ENTER E Shows the registration code authorized for the product. If you connect to the DivXⓇ web site and register using that code, you can download the VOD registration file.
Chapter 12 Support Software Update Current Version: This is the software version already installed in the product. MENU m → Support → Software Update → ENTER E The Software Update menu lets you upgrade your product software to the latest version. ――Be careful not to turn off the power until the upgrade is complete. The product will turn off and on automatically after completing the software upgrade.
Contact Samsung MENU m → Support → Contact Samsung → ENTER E View this information when your product does not work properly or when you want to upgrade the software. You can find information regarding our call centers and how to download products and software. ――Contact Samsung and find the product Model Code and Software Version.
Chapter 13 Troubleshooting Guide Requirements Before Contacting Samsung Customer Service Center Before calling Samsung Customer Service Center, test your product as follows. If the problem persists, contact Samsung Customer Service Center. If the screen remains blank, check the PC system, video controller and cable. Testing the Product Check if your product is operating normally by using the product test function.
Check the followings. Installation issue (PC mode) The screen keeps switching on and off. Check the cable connection between the product and PC, and ensure the connection is secure. Blank spaces are found on all four sides of the screen when an HDMI or HDMI-DVI cable is connected to the product and PC. The blank spaces found on the screen have nothing to do with the product. Blank spaces on the screen are caused by the PC or graphics card.
Screen issue The screen appears unstable and shaky. There are shadows or ghost images left on the screen. Check that the resolution and frequency of the PC and graphics card are set within a range compatible with the product. Then, change the screen settings if required by referring to the Additional Information on the product menu and the Standard Signal Mode Table. The screen is too bright. The screen is too dark. Adjust Brightness and Contrast. Screen color is inconsistent.
Screen issue The brightness and color do not look normal. Go to Picture and adjust the screen settings such as Picture Mode, Color, Brightness and Sharpness. Go to System and adjust the Eco Solution settings. Reset the screen settings to the default settings. Broken lines are displayed on the edges of the screen. If Picture Size is set to Screen Fit, change the setting to 16:9. Lines (red, green or blue) are displayed on the screen.
Sound issue Video is available but there is no sound. If an HDMI cable is connected, check the audio output settings on the PC. Go to Sound and change Speaker Select to Internal. If a source device is used •• Make sure the audio cable is properly connected to the audio input port on the product. •• Check the audio output settings for the source device. (For example, if an HDMI cable is connected to the SMART Signage TV, the audio setting for the cable box may need to be changed to HDMI.
Remote control issue The remote control does not work. Make sure that the batteries are correctly in place (+/-). Check if the batteries are flat. Check for power failure. Make sure that the power cord is connected. Check for any special lighting or neon signs switched on in the vicinity. Source device issue A beeping sound is heard when my PC is booting. If a beeping sound is heard when your PC is booting, have your PC serviced. Other issue Caption is grayed out and not selectable.
Other issue When I try to change the PC resolution, a message The defined resolution is not currently supported. appears. The message The defined resolution is not currently supported. appears if the input source resolution exceeds the maximum resolution of the display. To resolve the issue, change the PC resolution to a resolution supported on the display. There is no sound from the speakers in HDMI mode when a DVI-HDMI cable is connected. DVI cables do not transmit sound data.
Q&A Question Refer to the user manual for your PC or graphics card for further instructions on adjustment. How can I change the frequency? Answer Set the frequency on your graphics card. •• Windows XP: Go to Control Panel → Appearance and Themes → Display → Settings → Advanced → Monitor and adjust the frequency in Monitor Settings. •• Windows ME/2000: Go to Control Panel → Display → Settings → Advanced → Monitor and adjust the frequency in Monitor Settings.
Question How do I set powersaving mode? Answer •• Windows XP: Set power-saving mode in Control Panel → Appearance and Themes → Display → Screen Saver Settings or BIOS SETUP on the PC. •• Windows ME/2000: Set power-saving mode in Control Panel → Display → Screen Saver Settings or BIOS SETUP on the PC. •• Windows Vista: Set power-saving mode in Control Panel → Appearance and Personalization → Personalize → Screen Saver Settings or BIOS SETUP on the PC.
Chapter 14 Specifications - General Size Model Name Panel - Dimensions (W x H x D) / Weight V 40 CLASS (40.0 inches / 101 cm) 48 CLASS (47.6 inches / 121 cm) Display area 885.6 mm (H) x 498.15 mm (V) 1054.08 mm (H) x 592.92 mm (V) 34.87 inches (H) x 19.61 inches (V) 41.50 inches (H) x 23.34 inches (V) 906.6 x 532.9 x 65.1 mm / 7.6 kg 1075.1 x 627.6 x 65.5 mm / 11.1 kg 35.69 x 20.98 x 2.56 inches / 16.76 Ibs 42.33 x 24.71 x 2.58 inches / 24.47 Ibs 906.6 x 578.2 x 196.4 mm / 8.3 kg 1075.
――Plug-and-Play This SMART Signage TV can be installed and used with any Plug-and-Play compatible systems. Two-way data exchange between the SMART Signage TV and PC system optimizes the SMART Signage TV settings. SMART Signage TV installation takes place automatically. However, you can customize the installation settings if desired. ――Due to the nature of the manufacturing of this product, approximately 1 pixel per million (1ppm) may appear brighter or darker on the panel.
Power Consumption Normal Operation Typical Power Indicator Power Consumption Stand-by Rating Max Off On RM40D 56.4 W 89 W 98 W RM48D 68.5 W 104 W 114 W 0.5 W ――The displayed power consumption level can vary in different operating conditions or when settings are changed. ――SOG(Sync On Green) is not supported. ――To reduce the power consumption to 0, disconnect the power cord. Disconnect the power cable if you will not be using the product for an extended period of time (during vacation, etc.
Preset Timing Modes ――This product can be set to only one resolution for each screen size to obtain the optimum picture quality due to the nature of the panel. Using a resolution other than the specified resolution may degrade the picture quality. To avoid this, it is recommended that you select the optimum resolution specified for your product. ――Check the frequency when you exchange a CDT product (connected to a PC) for an LCD product.
Resolution Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) VESA, 640 x 480 37.500 75.000 31.500 -/- VESA, 800 x 600 37.879 60.317 40.000 +/+ VESA, 800 x 600 48.077 72.188 50.000 +/+ VESA, 800 x 600 46.875 75.000 49.500 +/+ VESA, 1024 x 768 48.363 60.004 65.000 -/- VESA, 1024 x 768 56.476 70.069 75.000 -/- VESA, 1024 x 768 60.023 75.029 78.750 +/+ VESA, 1152 x 864 67.500 75.000 108.000 +/+ VESA, 1280 x 720 45.000 60.
Chapter 15 Appendix Contact SAMSUNG WORLD WIDE Web site: http://www.samsung.com/us/sstv ――If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center. NORTH AMERICA U.S.
LATIN AMERICA DOMINICA 1-800-751-2676 ECUADOR 1-800-10-7267 EL SALVADOR 800-6225 GUATEMALA 1-800-299-0013 HONDURAS 800-27919267 JAMAICA 1-800-234-7267 NICARAGUA 001-800-5077267 MEXICO 01-800-SAMSUNG (726-7864) PANAMA 800-7267 PARAGUAY 009 800 542 0001 PERU 0-800-777-08 PUERTO RICO 1-800-682-3180 TRINIDAD & TOBAGO 1-800-SAMSUNG (726-7864) URUGUAY 000 405 437 33 VENEZUELA 0-800-100-5303 125
Responsibility for the Pay Service (Cost to Customers) ――When the service is requested, in spite of in warranty, we may charge you for a visit from a service technician in the following cases. Not a product defect Cleaning of the product, Adjustment, Explanation, Re-installation and etc. •• If a service technician gives instructions on how to use product or simply adjusts options without disassembling product. •• If a defect is caused by external environmental factors (Internet, Antenna, Wired Signal, etc.
Optimum Picture Quality and Afterimage Burn-in Prevention Black Matrix Common Electrode (ITO) Color-Filter Optimum Picture Quality Due to the nature of the manufacturing of this product, approximately 1 pixel per million (1ppm) may be brighter or darker on the panel. This does not affect product performance.
Preventing afterimage burn-in ――The best way to protect the product from afterimage burn-in is switching the power off or setting the PC or system to run a screen saver when not in use. Also, Warranty service may be limited depending on instruction guide. •• Powering Off, Screen Saver and Power Saving Mode -- Go to Display Properties > Power Supply on your PC and set the product to power off as required. -- Using a screen saver is recommended. It is best to use a single-color or moving-image screen saver.
License Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories. DivX Certified Ⓡ to play DivX Ⓡ video up to HD 1080p, including premium content. DivXⓇ, DivX CertifiedⓇ and associated logos are trademarks of Rovi Corporation or its subsidiaries and are used under license. Ⓡ 2.0 Channel Manufactured under license under U.S. Patent Nos: 5,956,674; 5,974,380; 6,487,535 & other U.S. and worldwide patents issued & pending.
Terminology 480i / 480p / 720p / 1080i / 1080p____ Each of the scanning rates above refers to the number of effective scanning lines that decides the screen resolution. The scanning rate may be indicated in i (interlaced) or p (progressive), depending on the scanning method. - Scanning Scanning refers to a process of sending pixels that form an image progressively. A larger number of pixels will deliver a clearer and more vivid picture.
