Contact SAMSUNG WORLD-WIDE If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care centre. Country AUSTRALIA CHINA HONG KONG INDIA INDONESIA JAPAN MALAYSIA New zealand PHILIPPINES SINGAPORE SOUTH AFRICA TAIWAN THAILAND TURKEY U.A.
User Instructions Screen Image retention Do not display a still image (such as on a video game or when hooking up a PC to this PDP) on the plasma monitor panel for more than 2 hours as it can cause screen image retention. This image retention is also known as “screen burn”. To avoid such image retention, reduce the degree of brightness and contrast of the screen when displaying a still image. Height The PDP can normally operate only under 2000m in height.
General Information PC Display User Instructions.............................................. 2 Checking Parts................................................. 4 Using the Stand-Base...................................... 4 Control Panel .................................................. 5 Connection Panel............................................. 6 Viewing the Remote Control ........................... 8 Operation Switching Your Television On and Off..............
Checking Parts Owner’s Instructions Remote Control/ AAA Batteries Power Cord Cloth-Clean Warranty Card/ Registration Card/ Safety Guide Manual (Not available in all locations) Cover-Bottom / Screws (2ea) (Refer to page 41) Ferrite Core for Power Cord Ferrite Core for Headphone (Not available in all locations) Sold Separately S-Video Cable Antenna Cable Component Cables Audio Cables PC Cable PC Audio Cable HDMI Cable HDMI/DVI Cable Video Cable Core (Power Cord, Headphone) ➢ Ferrite The fe
Control Panel Front Panel ➢ The product colour and shape may vary depending on the model. 1 SOURCE Toggles between all the available input sources (TV, AV1, AV2, S-Video, Component1, Component2, PC, HDMI1, HDMI2, HDMI3). ➢ In the on-screen menu, use this button as you would use the ENTER button on the remote control. 2 MENU Press to see an on-screen menu of your TV’s features. 3 + VOL – Press to increase or decrease the volume.
Connection Panel Side Panel 1 2 or 3 ➢ The product colour and shape may vary depending on the model. ☛ Whenever you connect an audio or video system to your set, ensure that all elements are switched off. When connecting an external device, match the colour of the connection terminal to the cable. 1 HDMI IN 3 Connect to the HDMI jack of a device with HDMI output. 2 AV IN 2(S-VIDEO or VIDEO / AUDIO R/L) Video (S-Video or Video) and Audio inputs for external devices, such as a camcorder or VCR.
Rear Panel 1 or Cable Television Network 9 2 4 or 8 7 6 3 5 ➢ The product colour and shape may vary depending on the model. ☛ Whenever you connect an audio or video system to your set, ensure that all elements are switched off. When connecting an external device, match the colour of the connection terminal to the cable. 1 ANT IN 75Ω Coaxial connector for Aerial/Cable Network. 2 SERVICE − Connector for service.
Viewing the Remote Control 1 POWER button (turns the TV on and off) 2 Selects the TV mode directly 3 Number buttons for direct channel access 4 One/Two-digit channel selection 5 Temporary sound switch-off 6 Volume increase Volume decrease 7 Channel control button (Refer to page 15) 8 Use to quickly select frequently used functions. 9 Control the cursor in the menu 0 Use to see information on the current broadcast # Press to select the optional display and sound modes for sports, cinema and games.
Installing Batteries in the Remote Control 1 2 3 Lift the cover at the back of the remote control upward as shown in the figure. Install two AAA size batteries. Make sure to match the “+” and “–” ends of the batteries with the diagram inside the compartment. Do not mix battery types, i.e. alkaline and manganese. Close the cover as shown in the figure. Remove the batteries and store them in a cool and dry place if you won’t be using the remote control for a long time.
Plug & Play Feature When the television is initially powered on, several basic customer settings proceed automatically and subsequently. The following settings are available. 1 2 3 If the television is in standby mode, press the POWER button on the remote control. The message Start Plug & Play. is displayed. Press the ENTER button. Language menu is displayed. Select the appropriate language by pressing the ▲ or ▼ button. Press the ENTER button.
If you want to reset this feature … 1 2 3 TV Setup Plug & Play Language : English Time Light Effect : In Watching TV Wall-mount Adjustment Melody : Off Entertainment : Off Energy Saving : Off PIP Press the MENU button to display the menu. Press the ▲ or ▼ button to select Setup, then press the ENTER button. Press the ENTER button again to select Plug & Play. The message Start Plug & Play. is displayed.
Viewing External Signal Sources You can switch between viewing signals from connected equipment, such as a VCR, DVD, Set-Top Box, and the TV source (broadcast or cable). 1 2 3 4 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Input, then press the ENTER button. Press the ENTER button again to select Source List. Press the ▲ or ▼ button to select the signal source, then press the ENTER button.
Editing Device Names You can give a name to the external source. 1 2 3 4 5 6 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Input, then press the ENTER button. Press the ▲ or ▼ button to select Edit Name, then press the ENTER button. Press the ▲ or ▼ button to select the external source to be edited, then press the ENTER button. Select the required device by pressing ▲ or ▼, then press the ENTER button.
Storing Channels Manually You can store television channels, including those received via cable networks. When storing channels manually, you can choose: Whether or not to store each of the channels found. The programme number of each stored channel which you wish to identify. 1 2 3 4 5 6 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Channel, then press the ENTER button. Press the ▲ or ▼ button to select Manual Store, then press the ENTER button.
Adding / Locking Channels Using the Channel Manager, you can conveniently add or lock channels. 1 2 3 TV Channel Area : Asia/W.Europe Auto Store Manual Store Channel Manager Sort Name Fine Tune Press the MENU button to display the menu. Press the ▲ or ▼ button to select Channel, then press the ENTER button. Press the ▲ or ▼ button to select Channel Manager, then press the ENTER button. Move Adding channels Using the Channel List, you can add channels.
Sorting the Stored Channels 1 2 3 4 5 6 Channel Area : Asia/W.Europe Auto Store Manual Store Channel Manager Sort Name Fine Tune Move Enter TV Return Sort Prog. Ch. 0 C−− C2 C83 C80 C7 C8 C9 C10 C11 C15 1 2 3 4 5 6 7 8 9 Name 7 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Channel, then press the ENTER button. Press the ▲ or ▼ button to select Sort, then press the ENTER button.
Fine Tuning Channel Reception If the reception is clear, you do not have to fine tune the channel, as this is done automatically during the search and store operation. If the signal is weak or distorted, you may have to fine tune the channel manually. 1 2 3 4 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Channel, then press the ENTER button. Press the ▲ or ▼ button to select Fine Tune, then press the ENTER button.
Customizing the Picture Settings Your television has several setting options that allow you to control the picture quality. 1 2 3 4 5 6 7 Press the MENU button to display the menu. Press the ENTER button to select Picture. Press the ENTER button again to select Mode. Select the required mode by pressing the ▲ or ▼ button, then press the ENTER button. Available modes: Dynamic, Standard, Movie Select the required option by pressing the ▲ or ▼ button, then press the ENTER button.
Black Adjust: Off/Low/Medium/High You can directly select the black level on the screen to adjust the screen depth. Dynamic Contrast: Off/Low/Medium/High You can adjust the screen contrast so that the optimal contrast is provided. Gamma: -3 ~ +3 You can adjust the middle brightness of pictures. Press the ◄ or ► button until you reach the optimal setting. Colour Space: Auto/Native/Custom Colour space is a colour matrix composed of red, green and blue colours.
Picture Options You can set detailed picture settings. 1 2 3 4 5 6 ➢ TV Press the MENU button to display the menu. Press the ENTER button to select Picture. Press the ▲ or ▼ button to select Picture Options, then press the ENTER button. Select the required option by pressing the ▲ or ▼ button, then press the ENTER button. When you are satisfied with your setting, press the ENTER button. Press the EXIT button to exit.
Digital NR: Off/Low/Medium/High/Auto If the signal received by the television is weak, you can activate this feature to reduce any static and ghosting that may appear on the screen. This function is not available in PC mode. ➢ Real 100Hz Demo : Off/On You can get a clear distinction between "Real 100Hz" and 50Hz, especially when watching sports. Therefore, when seeing a paused or static image, you will not be able to distinguish between "Real 100Hz" and 50Hz.
− − − ➢ ➢ ➢ White: This function helps remove after images on the screen by changing the colour of pixels to white. Use this function when there are remaining after images or symbols on the screen especially when you displayed a still image on the screen for a long time. Scrolling: This function helps remove after images on the screen by moving all the pixels on the PDP according to a pattern.
For more information on the 3D glasses (including the Emitter), refer to the user manual of your 3D glasses. Adjust the PC resolution - PS42A450 : 1024 x 768@60Hz - PS50A450 : 1024 x 768@60Hz 1360 x 768@60Hz The 3D IR Emitter communicates with the 3D glasses. Therefore, the 3D IR Emitter should be located near the 3D glasses. It is activated when the HDMI or DVI input signal is RGB, and DVI Sound is supported.
Resetting the Picture Settings to the Factory Defaults You can set detailed picture settings. 1 2 3 4 TV Press the MENU button to display the menu. Press the ENTER button to select Picture. Press the ▲ or ▼ button to select Reset, then press the ENTER button. Press the ▲ or ▼ button to select OK or Cancel then press the ENTER button.
SRS TS XT: Off/On TruSurround XT is a patented SRS technology that solves the problem of playing 5.1 multichannel content over two speakers. TruSurround delivers a compelling, virtual surround sound experience through any two-speaker playback system, including internal television speakers. It is fully compatible with all multichannel formats. TruSurround XT, SRS and Symbol are trademarks of SRS Labs, Inc. TruSurround XT technology is incorporated under license from SRS Labs, Inc.
Selecting the Sound Mode (depending on the model) The DUAL I-II button displays/controls the processing and output of the audio signal. When power is switched on, the mode is automatically preset to either “DUAL-I” or “Stereo”, depending on the current transmission. TOOLS Anynet+ (HDMI-CEC) Picture Mode : Sound Mode : Sleep Timer : SRS TS XT : Energy Saving : Dual I-II ◄ Easy Setting 1 2 3 Press the TOOLS button on the remote control. Press the ▲ or ▼ button to select Dual I-II.
Time Features 1 2 3 4 5 6 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Setup, then press the ENTER button. Press the ▲ or ▼ button to select Time, then press the ENTER button. Select the required option by pressing the ▲ or ▼ button, then press the ENTER button. Available options: Clock Set, Sleep Timer, Timer1, Timer2, Timer3 When you are satisfied with your setting, press the ENTER button. Press the EXIT button to exit.
Language / Light Effect / Melody / Entertainment / Energy Saving 1 2 3 4 5 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Setup, then press the ENTER button. Select the required option by pressing the ▲ or ▼ button, then press the ENTER button. When you are satisfied with your setting, press the ENTER button. Press the EXIT button to exit.
Viewing the Picture in Picture (PIP) You can display a sub picture within the main picture. In this way you can watch TV program or monitor the video input from any connected devices. 1 2 3 4 5 6 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Setup, then press the ENTER button. Press the ▲ or ▼ button to select PIP, then press the ENTER button. Select the required option by pressing the ▲ or ▼ button, then press the ENTER button.
Setting up Your PC Software (Based on Windows XP) The Windows display-settings for a typical computer are shown below. But the actual screens on your PC will probably be different, depending upon your particular version of Windows and your particular video card. But even if your actual screens look different, the same, basic set-up information will apply in almost all cases. (If not, contact your computer manufacturer or Samsung Dealer.
Input Mode (PC) Both screen position and size will vary depending on the type of PC monitor and its resolution. The table below shows all of the display modes that are supported: D-Sub Input Mode Resolution Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock Frequency (MHz) Sync Polarity (H/V) PS42A450 PS50A450 IBM 640 x 350 720 x 400 31.469 31.469 70.086 70.087 25.175 28.
Setting the PC ➢ Preset to the PC mode by pressing the SOURCE button. 1 2 3 4 5 TV Press the MENU button to display the menu. Press the ENTER button to select Picture. Select the required option by pressing the ▲ or ▼ button, then press the ENTER button. Available options: Auto Adjustment, Screen Adjustment, Reset When you are satisfied with your setting, press the ENTER button. Press the EXIT button to exit.
What is Anynet+? Anynet+ is an AV network system that enables an easy-to-use AV interface for users by controlling all connected AV devices through the Anynet+ menu when Samsung Electronics AV devices are connected. Connecting Anynet+ Devices The Anynet+ system supports AV devices supporting Anynet+ only. Check if there is an Anynet+ mark on the AV device to be connected to the TV.
Setting Up Anynet+ The following settings are to use Anynet+ functions. 1 Press the MENU button to display the menu. Press the ▲ or ▼ button to select Input, then press the ENTER button. 2 Press the ▲ or ▼ button to select Anynet+ (HDMI-CEC), then press the ENTER button. 3 Press the ▲ or ▼ button to select Setup, then press the ENTER button. 4 Press the ▲ or ▼ button to select Anynet+ (HDMI-CEC), then press the ENTER button. 5 Press the ▲ or ▼ button to select On, then press the ENTER button.
Anynet+ Menu The Anynet+ menu changes depending on the type and status of the Anynet+ devices connected to the TV. Anynet+ Menu View TV Select Device Record Menu on Device Device Operation Receiver Setup Description Switches from Anynet+ to TV broadcast mode. Your TV connects to the corresponding device. Starts a recording. (This menu works only for a device supporting recording.) Shows the menu of the connected device. Example. When a DVD Recorder is connected, the DVD Recorder’s title menu appears.
Listening through a Receiver You can listen to sound through a receiver instead of the TV speaker. 1 2 3 4 ➢ ➢ ➢ ➢ Press the MENU button to display the menu. TV P 1 Press the ▲ or ▼ button to select Input, then press the ENTER button. View TV Press the ▲ or ▼ button to select Anynet+ (HDMI-CEC), then press the Select Device ENTER button. Record Menu on Device Press the ▲ or ▼ button to select Receiver, then press the ENTER button.
Teletext Feature (depending on the model) Most television stations provide written information services via teletext. The index page of the teletext service gives you information on how to use the service. In addition, you can select various options to suit your requirements by using the remote control buttons. For teletext information to be displayed correctly, channel reception ☛ must be stable. Otherwise, information may be missing or some pages may not be displayed.
The teletext pages are organized according to six categories: Part A B C D E F Contents Selected page number. Broadcasting channel identity. Current page number or search indications. Date and time. Text. Status information. FASTEXT information.
Wall Mount Kit Specifications (VESA) Install your wall mount on a solid wall perpendicular to the floor. When attaching to other building materials, please contact your nearest dealer. If installed on a ceiling or slanted wall, it may fall and result in severe personal injury. Product Family inch VESA Spec.
Wall- mount adjustment (Sold separately) Once the auto wall mount is installed, the position of your TV can be easily adjusted. Rear Panel Auto Wall-Mount Serial Cable(1P to 1P)(Not supplied) Entering the menu 1 Press the ▲, ▼, ◄ or ► button on your remote control. ➢ The Wall Mount Adjustment screen is displayed. ➢ If the Wall Mount Adjustment screen is not displayed when clicking on a direction button while watching your TV, use the menu to display that screen.
Moving to the remembered position Complete Step 1 of Entering the menu. Wall-Mount Adjustment Pressing a Colour (Red, Green, Yellow) button moves the auto wall Position 1 mount to the saved position. ➢ You can move the wall mount to one of the 3 pre-set positions by pressing the Red (Position 1), Green (Position 2) or Yellow (Position 3) buttons. ➢ If you adjust the positon after moving to a pre-set position, the Position 1 2 3 position display will disappear.
Troubleshooting Before contacting the Samsung after-sales service, perform the following simple checks. If you cannot solve the problem using the instructions below, note the model and serial number of the television and contact your local dealer. No sound or picture Check that the mains lead has been connected to a wall socket. Check that you have pressed the (Power) button (On/Off) on the front panel or press the POWER button on the remote control. Check the picture contrast and brightness settings.
Specifications The descriptions and characteristics in this booklet are given for information purposes only and are subject to modification without notice.
This page is intentionally left blank. 책1.
