LCD PROJECTION TELEVISION Chassis : Model: COLOR TELEVISION RECEIVER M51A SP403JHPX/UMG CONTENTS 1. Precautions 2. Reference Information 3. Specifications 4. Disassembly and Reassembly 5. Alignment and Adjustments 6. Troubleshooting 7. Exploded View and Parts List 8. Electric Parts List 9. Block Diagram 10. PCB Layout Diagram 11. Wiring Diagram 12.
Precautions 1. Precautions Follow these safety, servicing and ESD precautions to prevent damage and protect against potential hazards such as electrical shock and X-rays. 1-1 Safety Precautions 1. Be sure that all of the built-in protective devices are replaced. Restore any missing protective shields. 2. When reinstalling the chassis and its assemblies, be sure to restore all protective devices, including: nonmetallic control knobs and compartment covers. 3.
Precautions 1-1 Safety Precautions (Continued) 9. High voltage is maintained within specified limits by close-tolerance, safety-related components and adjustments. If the high voltage exceeds the specified limits, check each of the special components. 10. Design Alteration Warning: Never alter or add to the mechanical or electrical design of this unit. Example: Do not add auxiliary audio or video connectors. Such alterations might create a safety hazard.
Precautions 1-2 Servicing Precautions Warning1: First read the “Safety Precautions” section of this manual. If some unforeseen circumstance creates a conflict between the servicing and safety precautions, always follow the safety precautions. Warning2: An electrolytic capacitor installed with the wrong polarity might explode. 1. Servicing precautions are printed on the cabinet. Follow them. 2.
Precautions 1-3 Precautions for Electrostatically Sensitive Devices (ESDs) 1. Some semiconductor (Òsolid stateÓ) devices are easily damaged by static electricity. Such components are called Electrostatically Sensitive Devices (ESDs); examples include integrated circuits and some field-effect transistors. The following techniques will reduce the occurrence of component damage caused by static electricity. 2.
Reference Information 2.
Reference Information Table 2-1 Abbreviations ABL AC ACC AF AFC AFT AGC AM ANSI APC APC A/V AVC BAL BPF B-Y CATV CB CCD CCTV Ch CRT CW DC DVM EIA ESD ESD FBP FBT FF FM FS GND G-Y H HF HI-FI IC IC IF 2-2 Automatic Brightness Limiter Alternating Current Automatic Chroma Control Audio Frequency Automatic Frequency Control Automatic Fine Tuning Automatic Gain Control Amplitude Modulation American National Standards Institute Automatic Phase Control Automatic Picture Control Audio-Video Automatic Volume Contr
Reference Information 2-2 IC Line Up Table 2 - 2 IC Line - Up BLOCK MAIN AV-TERMINAL SOUND MICOM LCD-CONTROL FEATURE-BOX Samsung Electronics SPECIFICATION MAKER FUNCTION TDA9810T PHILLIPS VIF (QSS-IF&AM) TDA7265 SGS-THOMSON STEREO AMP (25W) PCF8574P PHILIPS FAN,LEVER S/W,THERMO S/W DETECT SAA1300 PHILIPS LED CONTROL, LAMP ON/OFF TDA6920X SIEMENS 7*5 VIDEO S/W TEA5114A SGS-THOMSON VIDEO S/W TL062CDT T.
Reference Information Table 2 - 2 IC Line - Up BLOCK PIP 2-4 SPECIFICATION MAKER FUNCTION TDA9815 PHILIPS DEMODULATOR TDA9160 PHILIPS DECORDER/SYNC PROCESSOR SDA9187-2X SIMENS A/D CONVERTER FOR PIP SDA9189X SIMENS PIP PROCESSOR Samsung Electronics
Specifications 3. Specifications MODEL SP403JHP Progressive 0 Dolby Prologic 0 (3D Sound) AV- LINK 0 MAIN CHARACTERISTICS SYSTEM TUNING Frequency Synthesizer COLOR PAL, SECAM, NTSC SOUND NICAM, A2 STEREO, AM 75W, Coaxial Cable ANTENNA INPUT POWER CONSUMPTION 168 W REQUIREMENTS Input Range : 100 ~250V FREQUENCY 50Hz SIZE 1.
MEMO 3-2 Samsung Electronics
Disassembly and Reassembly 4. Disassembly and Reassembly 4-1 Back Cover Removal 1. After removing the 16 screws, pull the bottom part of the cabinet back wards. 2. Loosen the 4 screws and remove the supporter. 3. After loosening the 4 screws, remove the lens cover and fan duct. 4. Loosen the 2 screws. Remove the optical meter. 5. Loosen the 2 screws. Remove the stabilizer.
Disassembly and Reassembly 6. After loosening the 2 screws, remove the chassis holder and power mounting. 4-2 7. After removing the 6 screws, pull the top cabinet backwards.
Disassembly and Reassembly 4-2 Lamp Replacement 1. Loosen the screw. 2. Remove the cover. 3. Using a hexagonal wrench, loosen the two screws that secure the lamp. 4. Pull out the lamp. 5. PROCEDURE After completing the lamp replacement, enter the Service Mode Press the remote control Keys in the following sequence: ÒDisplay ➔ P.STD ➔ Mute ➔ PowerÓ (1) Select 01 (lamp life) with using the channel (▼) key, then press the volume (+) key (See the figure below).
Disassembly and Reassembly 4-2-1 Lamp (Bulb only) Replacement 1. Loosen the two screws. 2. Remove the lamp-bracket from the lamp assembly. 3. After loosening the two brackets, remove the lamp-holder and wires. 4. After loosening one screw and one nut, remove the bulb.
Disassembly and Reassembly 4-3 Air Filter Check 1. Loosen the screw. 2. Remove the cover. 3. After removing the holder and filter from the cover, clean the filter.
Disassembly and Reassembly 4-4 Liquid Crystal Panel Replacement 1. After removing the 16 screws, pull the cabinet backwards. 2. Loosen the 3 screws. Remove the supporter. 3. After loosening the 4 screws, remove the lens cover and fan duct. 4. Loosen the 2 screws. Remove the optical meter. 5. Remove the GUIDE from the FPC-Connector. 6. Remove FPC cable from the FPC-Connector.
Disassembly and Reassembly 7. Loosen the 2 screws, 2 PCB spacers and remove the PCB-LCD. 8. Using a hexagonal wrench, loosen the two screws. 9. Lift the LCD in the direction of arrow.
Disassembly and Reassembly 4-5 Speaker Removal 1. Loosen the 4 screws and remove the speaker holders.
Alignment and Adjustments 5. Alignment and Adjustments 5-1 Lens and Mirror Cleaning 1. Mix the alcohol and ethyl in appropriate proportions. 2. Use a clean cotton cloth or a cleaning paper. 3. Clean the top of the lens by turning it as shown. The pattern starts at the center and proceeds outward, as shown below: 4. Use minimal pressure when rubbing the mirror. Otherwise, the surface will be damaged. 5-2 Focus Adjustment for Projection Lens 1. Loosen the 4 screws that secure the optical assembly. 2.
Alignment and Adjustments 5-3 Liquid Crystal Screen Center Adjustment After replacing with the new liquid crystal panel, make sure that the liquid crystal screen center is aligned with the screen center. If they are not aligned, make the following adjustments: 1. Using a hexagonal wrench, loosen the two screws that secure the liquid crystal panel. Note: Loosen the screws just until the panel can move easily. 2. Using two fingers, lift the liquid crystal upward. (The screen moves downward.) 3.
Alignment and Adjustments 5-4 Side Panel Controls SIDE PANEL CONTROLS (THE OPERATION PANEL OPENS OUTWARD WHEN PRESSED) CHANNEL MENU VOLUME HEADPHONE R A U D I O L CHANNEL MENU V I D E O VOLUME HEADPHONE R A U D I O L V I D E O E X T 4 E X T 4 SVIDEO SAV Picture//Lamp//Standby/Temp 1 LED Indicator 5-4-2 Side Operation Panel 5-4-1 Rear Panel Jacks A/V IN E X T SELECTABLE 3 OUT A/V IN E X T CHANNEL SELECTABLE 2 OUT VIDEO Channel Select Button 1. Press for the channel selection. 2.
Alignment and Adjustments 5-5 Service Mode Adjustments 5-5-1 MATRIX IC (TDA4780) Adjustment No.
Alignment and Adjustments 5-5-2 LCD Interface IC (CXA1853_A) Adjustment No. Item Range Initial value Description 00 Gamma gain 1 63 41 Adjusts the gain of black side on the gamma curve (R,G.B) 01 R gamma gain 1 63 23 Adjusts the gain of black side on the gamma curve for R 02 B gamma gain 1 63 48 Adjusts the gain of black side on the gamma curve for B 03 Gamma gain 2 63 16 Adjusts the gain of white side on the gamma curve (R,G.
Alignment and Adjustments 5-5-3 LCD Interface IC (CXA1853_B) Adjustment No. Item Range Initial value Description 00 Gamma ctrl 1 off 63 41 Adjusts the change point of the black side on the gamma curve (R,G,B). The greater the value, the more it moves towards black 01 Black Stretch On 36 36 Adjusts the change point of the back side on the (R,G,B) gamma curve. Moves the change point to the white side. The value is always less than the one of the gamma ctrl 1 off.
Alignment and Adjustments 5-5-5 PIP Adjustment No. Item Range Initial value Description 00 Hisdel 15 10 Adjusts the position of PIP 01 Con 15 0 Adjusts the contrast of PIP 02 50.HSP - 0 - 03 50.VSP - 0 - Item Range Initial value lamp total time 05999 5-5-6 Lamp’s Total Hours No. 00 01 lamp time Description Records total elapsed time (from the time where power is first applied). Reset not possible Records total elapsed time (from the point where power is first applied).
Alignment and Adjustments 5-6 Circuit Adjustments 5-6-1 LCD Control Board PLL Adjustment 5-6-4 Matrix G Output Signal Amplitude Adjustment (Green Drive) 1. Input a color bar signal. 2. Connect CNL06,RPD to an oscilloscope, and check the waveforms. (1 V/div, 20 u sec/div) DC2.5V FPD 5-6-2 Matrix IC (TDA4780) Sub Tint Adjustment 1. Input a color bar signal. 2. Connect CNL07 (B output) to an oscilloscope, and check the waveform. (0.5 V/div, 20 u sec/div) 1. Input a 10-step signal (Color OFF). 2.
Alignment and Adjustments 5-6-7 R Main Brightness & B Main Brightness Adjustments 5-6-9 B Sub-brightness & B Contrast Adjustments 1. 1. Input a 5-step signal (Color OFF). Input a 5-step signal (Color OFF). 2. Connect CH1 to LCD G1 input and CH2 to LCD R,B input. (1 V/div, 10 u sec/div) 2. Connect CH1 to LCD G1 input and CH2 to LCD B1 input. (1 V/div, 10 u sec/div) 3. Reverse the CH2 signal, and add CH1 and CH2 in ADD mode. 3. Reverse the CH2 signal, and add CH1 and CH2 in ADD mode. 4.
Alignment and Adjustments 5-6-11 Sub-Contrast Adjustment 5-6-14 White Balance Adjustment 1. Input a 5-step signal (Color OFF). 1. Input a lion head pattern from a pattern generator. 2. Connect LCD G1 input to an oscilloscope. (2 V/div, 10 u sec/div) 3. Adjust the sub-contrast so that the signal level is 3V, as shown below: 2. Adjust the sub-brightness so that the white cannot be saturated. 3. Adjust R,B contrast for the high light of white balance. 4.
Alignment and Adjustments 5-7 LED Display Check PICTURE LAMP STAND BY/TEMP Green Red Red : OFF Status No 1 Master Power ON (in the Stand-by Mode) 2 Normal operation 3 Lamp is warming up. The normal picture comes on after 25 seconds. 4 Air vent cover in the rear of the TV is not properly installed. 5 Inside temperature of the TV is over normal. Clean the air vent cover in the rear of the TV. Turn the TV back on after 1 hour. (see below “Temperature”) 6 The lamp needs to be replaced.
Troubleshooting 6. Troubleshooting 6-1 Service Mode 1. To enter the Service Mode, press the remote-control keys in the following sequence: Display ® Picture Standard ® Mute ® Power 2. Use the Channel UP/DOWN keys to move within the Service Mode. 3. Use the Vol (+) key and Vol ( - ) key to change data. (1) Press the Vol (+) key to increase data. (2) Press the Vol (-) key to decrease data. 4. Use the Power key to exit and store data in memory.
Troubleshooting 6-2 No Power Check Stand-by 5V on the Main Board Yes No Check SDA1/SCL1 on the Micom Module See "6-5 No Standy" Yes Check LED Operation See "5-7 LED Display Check" No Check/Replace Tuner MICOM Module AUDIO Module A/V Terminal Board (TDA6920) Progressive Module LCD Control Board (TDA4780) 6-2 Samsung Electronics
Troubleshooting 6-3 No Picture Yes No No Check IC101 (TDA9810) #10 (AGC), #12 (CVBS) Check Progressive Module M-Y/CVBS,2Hsync,Vsync, 2Y,2R-Y,2B-Y,Href Yes Check/Replace IC101, Tuner Replace Progressive Module Check ICL404 (TDA4780) #14 (Sand castle pulse) No No Yes Yes Check IC401,402,403 #5 (74HC1230 No First check the circuitry connected to the IC and replace the IC Check ICL404(TDA4780)#6(B-Y) #7(R-Y),#8(Y),#27(SDA) #28(SCL) Check CL129, 130,131 and AC2 5P connector for #6,7,8 Check AC1
Troubleshooting 6-4 No Sound Yes No Check IC601,# 5 (MUTE) Check Audio Module MAIN-L, SUR, CENTER, S-RESET, QSS-IN Check/Replace IC101 Micom Module Audio Module No Yes Check/Replace Q602, Q603 Micom Module IC601 No Check IC604 #9, #14, #15 Check/Replace IC604 MICOM Module Yes Replace IC601 6-5 No Standby (+5V) Check the voltage of IC808 pin 5 (over 6V) Yes Check/Replace IC808 Regulator IC (SI-3050C) No Check the AC power supply of D826 Yes Check the associated circuitry parts of T802, I
Troubleshooting 6-6 No FAN Voltage (+8V) Check the voltage of IC805 pin 5 (12V) Check /Replace IC805 Regulator IC (SI-3050C) Yes No Check the voltage of T801 pin12 Yes Check L811, D821, C836 No Check T801/Replace trans 6-7 Lamp Does Not Work Standby/Temp LED, Picture LED, Lamp LED flicker at the same time? Or, check the lamp time (6000 hrs) Yes Check/Replace Lamp No Check the DC voltage of BALLAST (about 300V) No Check F801 (on the Power Board), D803, and surrounding circuitry Samsung Elec
Troubleshooting 6-8 Horizontal Sync Flows Horizontal Sync Flows Yes Check the output of 2H-Sync from the progressive module No Replace the progressive module Yes Check the output of 2H-Sync HREF to LCD Control Board No Check Connector Assy AC1 Yes Check the input of 2H-sync to ICL301(CXD2443Q) Pin 13 on the LCD Control Board No Check ICL402 (74HC123) Pin13,FI302 Yes Check the voltage of CNL06 RPD (2.8V) No Check voltage of TL301 so that the voltage of CNL06 RPD is 2.
Troubleshooting 6-9 Vertical Sync Flows Vertical Sync Flows Yes Check the output of V-Sync HREF from progressive module No Replace the progressive module Yes Check the input of V-Sync to LCD Control Board No Check Connector Assy AC1 Yes Check the input of V-Sync to ICL301 Pin 14 on LCD Control Board No Check ICL402 (74HC123) Pin 5 Yes Check CNL04 (connector to LCD panel) Samsung Electronics 6-7
Exploded View & Parts List 7.
Electric Parts List 8. Electric Parts List 8-1 SP403JHPX/UMG Parts List Loc. No. Code No. Description ; Specification Remark ASSY-PCB,MAIN(OPT) BUYER : HAD ELECTRO.CO.
Electric Parts List Loc. No. ! ! ! ! ! ! ! ! ! ! ! IC101 IC401 IC601 IC604 IC802 IC803 IC805 IC806 IC903 IC904 IC905 IFCAB J026 J094 J118 J126 J190 J267 J296 J297 J315 J327 L101 L102 L104 L105 L106 L107 L108 L109 L110 L113 L201 L276 L277 L278 L279 L280 L601 L602 L901 LP01 LP02 LP04 LP05 LP06 Q101 Q102 Q104 Q105 Q106 Q107 Q108 Q109 Q602 Q603 Q901 Q902 Q903 Q904 Q905 R101 R102 R103 R104 R105 R106 R107 R108 R109 R110 R111 R113 R116 R119 R120 R121 8-2 Code No. Description ; Specification Remark Loc. No.
Electric Parts List Loc. No. Code No.
Electric Parts List Loc. No. R721 R722 R723 R724 R725 R726 R727 R728 R729 R730 R731 R732 R733 R734 R735 R736 R737 R738 R739 R740 R744 R745 R747 R748 R749 R750 R752 R753 R754 R755 R756 R757 R758 R759 R760 R761 R762 R763 R764 R765 R766 R767 R768 R769 R770 R771 R772 R773 R774 R775 R776 R777 R778 R779 R781 R782 R783 R784 R785 R786 R787 R788 R789 R790 RP701 RP702 RP703 RP704 RP705 RP706 RP707 RP708 RP709 RP710 RP711 RP712 RP713 8-4 Code No.
Electric Parts List Loc. No. ICP102 ICP103 ICP105 ICP201 LP101 LP102 LP103 LP104 LP105 LP201 LP301 QP104 QP105 QP106 QP201 QP202 QP203 QP204 QP205 QP206 QP302 QP303 QP304 QP305 RC129 RP101 RP104 RP105 RP106 RP107 RP108 RP109 RP110 RP111 RP112 RP113 RP114 RP115 RP116 RP118 RP119 RP122 RP123 RP124 RP125 RP126 RP127 RP128 RP130 RP131 RP132 RP135 RP136 RP137 RP138 RP140 RP201 RP202 RP203 RP204 RP205 RP206 RP207 RP208 RP209 RP210 RP211 RP212 RP213 RP215 RP216 RP217 RP301 RP303 RP304 RP307 RP308 Code No.
Electric Parts List Loc. No. R904 R907 R908 R909 R910 R911 R912 R913 R914 R915 R916 R917 R918 R919 R920 R921 R922 R923 R924 R925 R926 R927 R928 R929 R930 R932 R935 R936 R937 R938 R952 R953 R954 R955 R956 R957 R958 RT01 RT02 RT03 RT04 RT05 RT06 RT07 RT08 RT09 RT11 RT12 RT13 RT14 RT15 RT16 RT17 X901 XT01 Code No.
Electric Parts List Loc. No. F801B ! F802 ! ! ! ! ! ! ! ! ! ! F802A F802B F803 F803A F803B F805 IC801 IC802 IC803 IC805 IC806 IC807 IC808 IC809 JP801A L801 L802 L803 L804 L805 L806 L807 L808 L809 L810 L811 L812 L813 L816 L817 L818 L819 P802F P807A Q801 Q804 R801 R802 R803 R804 R805 R806 R807 R808 R809 R810 R811 R812 R813 R814 R815 R816 R817 R818 R819 R820 R821 R822 R823 R824 R825 R826 R827 R828 R831 R832 R833 R834 R835 R836 R838 R839 R840 R841 R842 Code No.
Electric Parts List Loc. No. C669 C670 C671 C672 C679 C680 C681 C682 C683 C684 C685 C688 C691 C692 C694 C695 C696 C697 CD601 CD602 CD603 CD604 CD605 CD606 CD607 CD608 CD609 CD610 CD611 CD612 CD613 CD615 CD616 CD618 CD619 CD620 CD621 CD622 CD623 CD624 CD625 CD626 CD627 CD628 CD629 CD630 CN601A CN602A D601 D602 D603 D604 D605 D606 IC601 IC602 IC603 IC604 ICD601 ICD602 L601 L602 L603 LD601 LD602 LD603 Q604 Q605 Q606 Q607 R603 R604 R605 R606 R607 R608 R609 8-8 Code No.
Electric Parts List Loc. No. CL103 CL104 CL105 CL106 CL107 CL108 CL109 CL110 CL111 CL112 CL113 CL114 CL115 CL116 CL117 CL118 CL119 CL120 CL121 CL122 CL123 CL124 CL125 CL126 CL127 CL128 CL129 CL130 CL131 CL132 CL133 CL134 CL135 CL141 CL142 CL157 CL201 CL202 CL203 CL204 CL205 CL206 CL207 CL208 CL209 CL210 CL211 CL212 CL213 CL214 CL215 CL216 CL217 CL218 CL220 CL221 CL222 CL223 CL224 CL225 CL226 CL227 CL229 CL230 CL231 CL232 CL233 CL234 CL235 CL236 CL237 CL238 CL239 CL240 CL242 CL243 CL244 Code No.
Electric Parts List Loc. No.
Electric Parts List Loc. No. RL266 RL267 RL268 RL301 RL302 RL303 RL304 RL305 RL306 RL307 RL308 RL310 RL313 RL314 RL315 RL316 RL317 RL318 RL320 RL321 RL322 RL323 RL324 RL325 RL326 RL327 RL328 RL329 RL330 RL331 RL332 RL333 RL334 RL335 RL336 RL401 RL402 RL403 RL404 RL405 RL406 RL407 RL408 RL409 RL501 RL502 RL503 TL301 Code No.
Electric Parts List Loc. No. IC212 L202 L203 L204 L205 L206 L207 L208 L210 L211 L212 L213 L214 L215 L216 L217 L218 L220 L230 L232 L233 L236 L237 LF01 LF02 Q203 R1 R11 R13 R15 R16 R18 R20 R212 R213 R215 R216 R217 R218 R219 R22 R220 R221 R222 R223 R224 R225 R226 R227 R228 R229 R230 R231 R232 R234 R235 R236 R237 R238 R24 R242 R250 R251 R252 R26 R266 R267 R268 R269 R28 R3 R30 R302 R303 R304 R400 R403 8-12 Code No.
Electric Parts List Loc. No. Code No. Description ; Specification Remark Loc. No. AA64-30858ACASE-DRAWER,BODY;-,ABS,HB,-,-,BLK,-,SVP-403J AA64-60444AINLAY-CONTROL,PAL;SPM-403J,-,PS,T0.4,BLK,-,- ASSY-S/W,DETECTOR * AA95-90021F ASSY-S/W,DETECTOR;-,SVP-403J,ALT51A,NTSC,110-220 AF1A SL+BS SW AA39-20015MLEAD CONNECTOR-ASSY;-,67096-003,-,3(2)P,900mm,1007 6001-001003 SCREW-MACHINE;BH,+,M2.6,L6,ZPC(BLK),SWRCH10A 3409-000178 SWITCH-LEVER;12V,100mA,SPDT,-,27deg AA61-10185ABRACKET-SENSOR;-,L3300,SECC,T1.
Block Diagram 9. Block Diagram 9-1 M51A (SP403JHP) F E AT UR E B OX # MAIN TUNER : [ TECC2949PG30A(S) ] +9V +5V +33V +5V AGC SCL SW AS N.C SDA IF N.C 27MHZ 2 I C SAW-VIF K6263K SAW-SIF K9462M HS1 VS1 # PIP TUNER : [ TECC2849PG29A(S) ] +33V +5V AGC N.C AS SCL SDA MULTI N.C IF N.
PCB Layout Diagram 10. PCB Layout Diagram 10-1 PCB-MAIN Loc. No.
PCB Layout Diagram 10-2 PCB-POWER Loc. No.
PCB Layout Diagram 10-3 PCB-PROGRESSIVE 10-4 PCB u-COM 10-5 PCB-LCD CONTROL 10-6 PCB-A/V TERMINAL Samsung Electronics 10-3
PCB Layout Diagram 10-7 PCB-AUDIO 10-8 PCB-PIP 10-10 PCB-A/V CONTROL 10-9 PCB-REMOCON 10-12 PCB-MASTER S/W 10-11 PCB-SIDE KEY 10-4 Samsung Electronics
5 6 FRONT-R 7 8 GND 9 FRONT-L HEAD R 10 HEAD L CNM14 GND FAN Samsung Electronics 9 SIDE-KEY SIDE-JACK GND FAN CN602A AUDIO CN601A 17 18 15 16 17 18 GND MAIN R 2 2 3 4 5 6 7 N-C GND S1-R S1-G 10 9 10 11 12 13 14 15 GND H-SYNC VS CN205 GND SDA SCL 3 4 5 6 3 4 5 6 CN206 4 5 4 5 CN203 4 4 9 11 12 13 14 11 12 13 14 8 10 9 8 B-Y GND GND GND NC GND OSD-F/B 10 9 8 7 6 5 10 9 8 7 6 5 4 3 2 1 6 5 4 3 2 1 12 11 10 GND SDA1 GND NC GND OSD-F/B GND
Schematic Diagrams 12.
Schematic Diagrams 12-2 MAIN (2) 15 15 @? @@@@@?@? @?e@? W2@@6Xe?@@? ?@@? @?e@? O2@??W2@@6X?W2@@6X?W2@@6X?f?@@?W2@@6Xe?W2@g?@@?eO2@??W2@@6X?heO2@??W2@@6X?e?W2@@6X?@@@@@@gO2@??W2@@6X? 7@eB1e?@@L ?@@? @?e@? ?@@@@??7@??@1?7@e@1?7@??@1?fJ@5?7@e@1e?7@@gJ@5??@@@@??7(MI'1?h?@@@@??7@??@1?@@?7@??@1?@@f?@@??@@@@??7(MI'1? @@e?@?@@@@@e?W2@6Xe?@@@@6X?e@@@@6Xe?W2@6Xg?@5? @?e@? ?@@??@@??@@?@@e@@?@@??@@?f7@H?@@e@@eJ@@@g7@H?e?@@??(Y?e@?he?@@??@@??@@?@@?@@??@@?@@f?@@?e?@@??(Y?e@? 3@f?N@@fW&@1e?@@??@1?e@@e@1eW&(MS1eW2@@
Schematic Diagrams 12-3 MAIN (POWER) : Power Line : Signal Line Samsung Electronics 12-3
Schematic Diagrams 12-4 PROSCAN (1) : Power Line : Signal Line 12-4 Samsung Electronics
Schematic Diagrams 12-5 PROSCAN (2) : Power Line : Signal Line Samsung Electronics 12-5
Schematic Diagrams 12-6 PROSCAN (3) : Power Line : Signal Line 12-6 Samsung Electronics
Schematic Diagrams 12-7 PROSCAN (4) Samsung Electronics 12-7
Schematic Diagrams 12-8 MAIN (u-COM) : Power Line : Signal Line 12-8 Samsung Electronics
Schematic Diagrams 12-9 MAIN (AUDIO) 23 24 23 ?@ ?@@@@@?@ W2@@6Xe?@@? ?@@? ?@e?@ O2@??W2@@6X?W2@@6X?W2@@6X?f?@@?W2@@6X?W2@@6X?f?@@?eO2@?e?O2@heW2@@6X?W2@@6X?e?W2@@6X?eO2@?f@@@@@@?W2@@6X? 7@eB1e?@@L ?@@? ?@e?@ ?@@@@??7@??@1?7@e@1?7@??@1?fJ@5?7@e@1?7@??@1?fJ@5??@@@@?e@@@@he7@e@1?7@??@1?@@?7(MI'1??@@@@??@@?@@f?7@??@1? @@e?@?@@@@@e?W2@6Xe?@@@@6X?e@@@@6Xe?W2@6Xg?@5? ?@e?@ ?@@??@@??@@?@@e@@?@@??@@?f7@H?@@e@@?@@??@@?f7@H?e?@@?f@@he@@e@@?@@??@@?@@?(Y?e@?e?@@??@@?@@f?@@??@@? 3@f?N@@fW&@1e?@@??@1?e@@e@1eW&(MS1eW
Schematic Diagrams 12-10 MAIN (A/V TERMINAL) : Power Line : Signal Line 12-10 Samsung Electronics
Schematic Diagrams 12-11 CONTROL LCD (1) 25 ?@ ?@@@@@?@ W2@@6Xe?@@? ?@@? ?@e?@ O2@??W2@@6X?W2@@6X?W2@@6X?f?@@?W2@@6X?W2@@6X?f?@@?eO2@?e?O2@heW2@@6X?W2@@6X?f?W2@eW2@@6XfW2@@6X?W2@@6X? 7@eB1e?@@L ?@@? ?@e?@ ?@@@@??7@??@1?7@e@1?7@??@1?fJ@5?7@e@1?7@??@1?fJ@5??@@@@?e@@@@he7@e@1?7@??@1?@@e?7@@e7(MI'1?@@?7(MI'1?7(MI'1? @@e?@?@@@@@e?W2@6Xe?@@@@6X?e@@@@6Xe?W2@6Xg?@5? ?@e?@ ?@@??@@??@@?@@e@@?@@??@@?f7@H?@@e@@?@@??@@?f7@H?e?@@?f@@he@@e@@?@@??@@?@@eJ@@@e(Ye?@?@@?(Ye?@?(Y?e@? 3@f?N@@fW&@1e?@@??@1?e@@e@1eW&(MS1eW2@@@
Schematic Diagrams 12-12 CONTROL LCD (2) 34 ?@ ?@@@@@?@ W2@@6Xe?@@? ?@@? ?@e?@ O2@??W2@@6X?W2@@6X?W2@@6X?f?@@?W2@@6X?W2@@6X?f?@@?eO2@?e?O2@heW2@@6X?W2@@6X?e?W2@@6X?eO2@?fW2@@6X?@@@@@@? 7@eB1e?@@L ?@@? ?@e?@ ?@@@@??7@??@1?7@e@1?7@??@1?fJ@5?7@e@1?7@??@1?fJ@5??@@@@?e@@@@he7@e@1?7@??@1?@@?7@??@1??@@@@??@@?7(MI'1?@@? @@e?@?@@@@@e?W2@6Xe?@@@@6X?e@@@@6Xe?W2@6Xg?@5? ?@e?@ ?@@??@@??@@?@@e@@?@@??@@?f7@H?@@e@@?@@??@@?f7@H?e?@@?f@@he@@e@@?@@??@@?@@?@@??@@?e?@@??@@?(Ye?@?@@? 3@f?N@@fW&@1e?@@??@1?e@@e@1eW&(MS1eW2@@@@
Schematic Diagrams 12-13 CONTROL LCD (3) 41 43 42 @? @@@@@?@? @?e@? W2@@6Xe?@@? ?@@? O2@??W2@@6X?W2@@6X?W2@@6X?f?@@?W2@@6X?W2@@6X?f?@@?W2@@6X?W2@@6X?f@?e@?O2@??W2@@6X?f?O2@eW2@@6XfW2@@6X?W2@@6X? 7@eB1e?@@L ?@@? ?@@@@??7@??@1?7@e@1?7@??@1?fJ@5?7@e@1?7@??@1?fJ@5?7(MI'1?7@??@1?f@?e@@@@@??7@??@1?@@e@@@@e7@e@1?@@?7@e@1?7@??@1? @@e?@?@@@@@e?W2@6Xe?@@@@6X?e@@@@6Xe?W2@6Xg?@5? ?@@??@@??@@?@@e@@?@@??@@?f7@H?@@e@@?@@??@@?f7@H?(Ye?@?@@??@@?f@?e@??@@??@@??@@?@@f@@e@@e@@?@@?@@e@@?@@??@@? 3@f?N@@fW&@1e?@@??@1?e@@e@1
Schematic Diagrams 12-14 MAIN-PIP : Power Line : Signal Line 12-14 Samsung Electronics
Schematic Diagrams 12-15 MAIN SUB (MASTER/REMOCON/PRE-AMP) Samsung Electronics 12-15
ELECTRONICS © Samsung Electronics Co., Ltd. MAY.