To avoid injuries or damage to property, please read the following precautions carefully and use the product accordingly. Failure to follow the instructions marked with this symbol may cause personal injury or even fatality. Failure to follow the instructions marked with this symbol may cause personal injury or damage to the product or property. | Power Related | Installation Related | Cleaning and Use Related | [The images here are for reference only, and are not applicable in all cases (or countries).
To disconnect the apparatus from the mains, the plug must be pulled out from the mains socket, therefore the mains plug shall be readily operable. There is a danger of electric shock or fire. z Always unplug the unit by holding the power plug. Pulling the power cable may damage the inside of it. There is a danger of fire. z Unplug the power plug before cleaning the product. There is a danger of electric shock or fire.
Do not install on an unstable location, or on a stand smaller than the product. z Make sure to keep the product out of the reach of children. The product may fall and cause personal injury. In case of thunder/lightning, disconnect the power cord from the wall outlet. z There is a danger of electric shock or fire. Make sure the product's vents are not blocked by a table cloth or curtain. z An increase in the internal temperature may cause a fire. Place the product on the ground carefully.
z This may cause electric shock or fire. If water or an alien substance enters the product, turn the product off, disconnect the power cord from a wall outlet and contact a Service Center. Do not disassemble, or attempt to fix or modify the product. z When the product requires repairs, contact a Service Center. Do not use or keep the product near flammable sprays or other such substances. z There is a danger of fire or explosion.
When cleaning the product, disconnect the power cord and wipe the product using a soft dry cloth. z Do not use any chemicals such as wax, benzene, alcohol, thinners, insecticide, air freshener, lubricant or detergent. When not using the product for an extended period of time, disconnect the power plug. z Otherwise, this may cause heat emission from the accumulated dirt or degraded insulation, leading to electric shock or fire.
| Product Features | Product Views | Remote Control | Product Specifications | High Mobility Design - Small Size. - Lightweight. Next Generation Backlight Light Source, LED Lamp - Effective energy saving by using low voltage. - Semi-permanent long lifetime guaranteed. | Product Features | Product Views | Remote Control | Product Specifications | Front/Upper Side 1. Indicators 6.
/ : Use this button to move to or select an item within a menu. - TEMP (Red LED) - STAND BY (Blue LED) ※ Refer to the LED Indications. : Use this button to adjust the volume. 2. Lens cover 7. MENU Button Use this button to enter or exit a menu or to move 3-1. Adjustable Feet You can adjust the screen position by moving the adjustable feet up and down. forward in a menu. 8. SOURCE Button Use this button to select the external device 3-2. The holes to hold the tripod signal. 4. Lens 9.
LED Indications :Light is On STAND BY :Light is Blinking :Light is Off TEMP Information This state occurs when power is supplied to the projector normally after the POWER button on the projector or the remote control has been pressed. - This state appears when the projector is preparing an operation after the POWER button on the projector or the remote control has been pressed.
1. VIDEO IN Input port 5. Kensington Lock 2. VIDEO/PC AUDIO IN Input ports 6. PC IN Input port 3. Remote Control Signal Receiver 7. SERVICE Input port 4. POWER Input port 8.
1. POWER Button ( 2. SOURCE Button 3. MENU Button( 4. Move( 5. VERTICAL KEYSTONE Button ( 6. INSTALL Button 7. STANDARD Button 8. P.SIZE Button 9. QUICK Button ) ) )/ ( 10. MUTE Button ( )Button ) ) 11. RETURN Button( ) 12. EXIT Button 13. VOL Button ( ) 14. STILL Button 15. MONITOR Button 16. P.MODE Button 17. MOVIE Button 1. POWER Button ( ) Use this button for turning the product on and off. 2. SOURCE Button Used to check or select the connection status of external devices. 3.
Used to make Menu Screen disappear. 13. VOL Button ( ) Adjusts the audio volume. 14. STILL Button Used to see still images. 15. MONITOR Button Used to set the projector to the optimal mode when used as a monitor. 16. P.MODE Button Used to select Picture Mode. 17. MOVIE Button Use this when the surroundings are dark. | Product Features | Product Views | Remote Control | Product Specifications | Design and specifications of the product may be modified without prior notice for better performance.
exceed the maximum number of bad pixels set by our standards. Rarely, non-displayable pixels may exist, however it does not affect the picture quality nor the lifespan of the product. Supported Display Modes Horizontal Vertical Clock Frequency Frequency (kHz) Frequency (Hz) (MHz) (Horizontal /Vertical) IBM, 640 x 350 31.469 70.086 25.175 +/- IBM, 640 x 480 31.469 59.940 25.175 -/- IBM, 720 x 400 31.469 70.087 28.322 -/+ MAC, 640 x 480 35.000 66.667 30.240 -/- MAC, 832 x 624 49.
Picture Position Modes Source Input VIDEO PC Picture Position (H/V) Mode Normal Zoom 1 Zoom 2 16:9 576i x x x x 480i x x x x 16:9 Mode O x x O 4:3 Mode O x x O
| Basic Settings | Connecting the Power | Connecting to video equipment | Installing the Projector Install the projector so that the beam from the projector is perpendicular to the screen. Place the projector so that the lens is at the center of the screen. If the screen is not vertically installed, the picture on the screen may not be a rectangle. Do not install the screen in bright surroundings. If the screen is too bright, the picture on the screen will not be displayed clearly.
Focus Ring Focus the picture on the screen using the Focus Ring. If your product is installed at a location out of the specified projection distance (refer to Screen Size and Projection Distance), the focus cannot be adjusted correctly. Leveling with Adjustable Feet For level placing of the projector, adjust the Adjustable Feet of the projector. You may adjust the level of the projector up to 3 degrees. Depending on the position of the projector, Keystone distortion of image may appear.
Setting up the PC Environment - Check the following items before connecting your PC to your projector. 1. Click the right mouse button on the Windows desktop and click on [Properties]. tab will appear. 2. Click on [Settings] tab and set the by referring to described in the display mode table supported by this projector. You do not have to change setup. 3. Press the [Advanced] button. Another property window will appear. 4.
Process might vary depending on the type of computers or Windows versions. (For example, [Properties] appears instead of [Properties (R)] as shown in 1.) This appliance supports up to 32 bits per pixel in Color quality when it is used as a PC monitor. Projected images may differ from the monitor depending on monitor manufacture or Windows versions. When connecting the projector to a PC, check that PC setup complies to display settings supported by this projector. If not, there may be signal problems.
- Connect [VIDEO IN(yellow)] input port of the projector to the VIDEO (yellow) OUT port of video equipment using the video cable. - Connect the [ ] input port of the projector to the Audio (L), Audio (R) output ports of the external device, such as a DVD, VCR or camcorder using an audio cable. When the connections are all completed, connect both power cables of the projector and the DVD, VCR, or camcorder.
Connect [PC IN] port on the rear side of the projector to the monitor output port of the PC using a PC video cable. When connections are all completed, connect both power codes of the projector and the PC. Connect the [VIDEO/PC AUDIO IN] input port of the projector to the speaker output ports of the PC using an audio cable. This product supports plug and play and therefore, if you use Window XP you do not need to setup the driver on your PC.
Kensington Lock The Kensington Lock is a device used to physically fix the system when using it in a public place. The locking device has to be purchased separately. The appearance and locking method may differ from the illustration depending on the manufacturer. Refer to the manual provided with the Kensington Lock for proper use. The locking device has to be purchased separately.
| Input | Picture | Setup | Option | * Click the Play( Screen Play/Stop You can select a device connected to the projector to display. 1) Video Edit Name ) button in the table below to view the video file. Description Adjustment Source List )/Stop( 2) PC You can edit the names of devices connected to the projector.
* Click the Play( Screen ) button in the table below to view the video file. Description Adjustment Mode )/Stop( Play/Stop Select a screen state which is customized to your projector or change the screen mode as required. 1) Mode - Dynamic Select this if you want the screen quality to be clearer than standard screen quality. - Standard You can comfortably view the projection screen if the surrounding is somewhat bright. - Movie Select this if your surroundings are dark.
Gamma - Video : The best setting for watching a TV program. - Graphic : The best setting when you have a PC connected. - Vivid : The gamma mode suitable for watching a movie. 9) Save : Used to save custom picture settings. Save 10) Reset : Restores the mode settings to the factory defaults. Reset Size You can select a screen size according to the type of scene.
* Click the Play( Screen ) button in the table below to view the video file. Description Adjustment Install )/Stop( Play/Stop To tailor the picture to the installation location, you can invert the projected images vertically/horizontally.
2) Coarse : Used to adjust frequency when vertical lines appear on PC screen. Zoom 3) Fine : Used to fine tune the PC screen. 4) Zoom : Used to extend PC screen from the center. Reset 5) Reset : Using this function, you can reset the PC menu settings to the factory default settings. Factory Default Using this function, you can reset various settings to the factory default settings.
Menu Display You can set the display time of the menu. Time 1) 5 sec 5) 90 sec 2) 10 sec 6) 120 sec 3) 30 sec 7) Stay On 4) 60 sec Logo If Logo mode is enabled, the Samsung logo is displayed when the projector is turned on. If disabled, it is not displayed. Blue screen The Blue screen function causes the screen to change to the Blue screen if there is no signal input from the external device connected to your projector.
| Before Contacting Service Personnel | Installation and Connection Symptoms Troubleshooting No Power. z I want to install my projector on z Check the power cable connections. The ceiling installation support is sold separately. Contact your local product distributor. the ceiling. External Source can not be z Be sure that the connection cable(s) (video) is properly connected to the proper port. If the device is not connected properly, it can not be selected. selected.
correctly in the command screen of the Projector menu. Only blue screen appears. z Be sure to properly connect the external devices. Check the connection cables again. Screen appears in black and white or z bright. As mentioned above, check the adjustment items such as the Brightness, Contrast and Color in the menu. odd color./ screen is too dark or z If you want to restore various settings to their factory defaults, run from the menu.
| Care and Maintenance | Contact SAMSUNG WORLDWIDE | Other | Authority | To clean the exterior and lens of the projector Clean the projector using a soft dry cloth. Do not clean the projector with flammable substances such as benzene, thinners or a wet cloth, as these may cause problems. Do not touch the projector with a nail or any other sharp objects, as this may scratch the surface.
Latin America ARGENTINE BRAZIL 0800-333-3733 http://www.samsung.com/ar 0800-124-421 http://www.samsung.com 4004-0000 CHILE 800-SAMSUNG(726-7864) http://www.samsung.com/cl COLOMBIA 01-8000112112 http://www.samsung.com.co COSTA RICA 0-800-507-7267 http://www.samsung.com/latin ECUADOR 1-800-10-7267 http://www.samsung.com/latin EL SALVADOR 800-6225 http://www.samsung.com/latin GUATEMALA 1-800-299-0013 http://www.samsung.
SLOVAKIA 0800-SAMSUNG (7267864) http://www.samsung.com/sk SPAIN 902 10 11 30 http://www.samsung.com SWEDEN 0771-400 200 http://www.samsung.com/se SWITZERLAND 0800-SAMSUNG(726-7864) http://www.samsung.com/ch U.K 0845 SAMSUNG (7267864) http://www.samsung.com CIS ESTONIA 800-7267 http://www.samsung.ee LATVIA 800-7267 http://www.samsung.com/lv LITHUANIA 8-800-77777 http://www.samsung.lt KAZAKHSTAN 8-10-800-500-55-500 http://www.samsung.
| Care and Maintenance | Contact SAMSUNG WORLDWIDE | Other | Authority | Glossary Gamma Mode Gamma Mode compensates the video signal produced for analog display devices such as a CRT (Cathode Ray Tube) so that the video signal can be clearly displayed on a digital display device. Black Level Black Level sets the light level of the darkest portion of the video signal to match that of the display's black level capability so that users can clearly view dark visuals.
light onto a 40-inch screen, divide the screen into 9 rectangles and measure the average brightness of each of the rectangles. Since the brightness at the center is generally different from that of the edges, ANSI Lumen provides a more precise measure of the projector brightness than LUX. AV Receiver An AV Receiver provides a number of input and output interfaces for audio and video so as to enable the user to connect and use various input and output devices.
| Care and Maintenance | Contact SAMSUNG WORLDWIDE | Other | Authority | Information in this document is subject to change without notice. ⓒ 2008 Samsung Electronics Co., Ltd. All rights reserved. Reproduction in any manner whatsoever without the written permission of Samsung Electronics Co., Ltd. is strictly forbidden. Samsung Electronics Co., Ltd.
