USER MANUAL 4 CHANNELS NETWORK DIGITAL VIDEO RECORDER i
INSTRUCTION MANUAL To obtain the best performance and ensure device function correctly, please read this instruction manual carefully and completely. FCC Compliance USER-INSTALLER CAUTION: YOUR AUTHORITY TO OPERATE THIS FCC VERIFIED EQUIPMENT COULD BE VOIDED IF YOU MAKE CHANGES OR MODIFICATIONS NOT EXPRESSLY APPROVED BY THE PARTY RESPONSIBLE FOR COMPLIANCE TO PART 15 OF THE FCC RULES.
Warnings and Cautions WARINGS TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MISTURE. DO NOT INSERT ANY METALLIC OBJECT THROUGH VENTILATION GRILLS. CAUTION CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK. DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
TABLE OF CONTENTS CHAPTER 1 INTRODUCTION ------------------------------------------------------------------------------------------ 1 FEATURE ---------------------------------------------------------------------------------------------------------- 1 CHAPTER 2 HARDWARE OVERVIEW ------------------------------------------------------------------------------ 2 CHAPTER 3 SETUP PROCEDURES --------------------------------------------------------------------------------- 4 1.
SETUP MENU List SYSTEM SETUP SETUP MENU BUZZER DURATION VIDEO LOSS ALARM HDD PASSWORD SET TIME/DATE EXIT SYSTEM SETUP CAMERA SETUP 3 SEC ON CAMERA SETUP CAMERA SELECT CH1 CAMERA RECORD ON MOTION DETECTION ON MOTION SENSITIVITY 5 BRIGHTNESS STANDARD CONTRAST STANDARD HUE STANDARD EXIT RECORD SETUP SCHEDULE RECORD EVENT LIST HDD MANAGEMENT RECORD SETUP RECORD MODE MUX NORMAL RECORD FPS 15P ALARM RECORD FPS 15P ALARM REXORD DWELL 5 SEC RECORD QUALITY HIGH MOTION EVENT MIGRATION OFF EXIT LOAD DEFAULT E
CHAPTER 1 INTRODUCTION This product is 4 cameras input appliance with multiple function which will bring you following features: z Device can be performed as VHS system with live display, play back and video recording。 z Device operates in hardware base with no OS (operating system) necessary for more reliability and stability。 z Digitize data storage with M-JPEG compression technology will give you organized video data management without using mess huge traditional video tape。 z Support various typ
CHAPTER 2 Hardware Overview Front Panel Layout Overview 5 6 7 8 9 10 11 12 13 14 15 16 17 22 23 1 2 3 4 19 18 20 21 Buttons Function List Part Label 1 POWER 2 REC Recording status LED. 3 PLAY Playback status LED. 4 H.D.D H.D.D LED 5 6 7 8 9 10 11 12 13 Function Power status LED. 1 1. 2. This View button controls FULL SCREEN display from camera 1. A password can be setup by the view control button for number 1. 2 1. 2.
14 F.Fwd Search 15 Press F. Fwd to play video forward at high speed. Press the button again the speed will be change circulative from ×2,×4, , to the highest ×6. Press the Play button to into time search and play video forward. PLAY 16 MENU Press MENU to go into or exit menu. 17 ▲ 1. Move the cursor upward or decrease the number. 2. When it’s not under recording mode, you can use the button to adjust position of date & time display which appears on OSD. 18 ▼ 1.
CHAPTER 3 SETUP PROCEDURES 1. MAIN MENU SETUP Press the MENU button to go into the main menu. SETUP MENU Use the ▲ or ▼ button to select items. > SYSTEM SETUP CAMERA SETUP RECORD SETUP SCHEDULE RECORD EVENT LIST HDD MANAGEMENT LOAD DEFAULT EXIT Press the ◄ or ► button to confirm the selection. Press MENU to escape to exit the set up mode.
Exit from the SYSTEM SETUP menu 3. CAMERA SETUP Press the MENU button to go into the main menu. CAMERA SETUP Use the ▲ or ▼ button to select items. > CAMERA SELECT CAMERA RECORD MOTION DETECTION MOTION SENSITIVITY BRIGHTNESS CONTRAST HUE EXIT CH1 ON ON 5 STANDARD STANDARD STANDARD Press the ◄ or ► button to confirm the selection. Press MENU to escape to exit the set up mode. Contents: c CAMERA SELECT CH1(CH1~CH4) Use ◄ or ► button to select the camera from CAM 1 – CAM 4 to be adjusted.
f g h i detection is triggered. Note: PAL: (1~4P/6P/8P/12P/25P) NTSC=15P, PAL=12P on default. ALARM RECORD DWELL 5SEC (1-30) Use ◄ or ► button to set the dwell time for alarm recording when external alarm or motion detection is triggered. When external alarm is triggered and within the dwell period: - the screen will be switched into 4 format.
and down for indicating current event which been selected. Press “◄ or ►” key to select events storage from master hard drive or slave hard drive . When once selection has been made and than press ►PLAY key to start playing records in normal speed. There are totally 4 different type’s event will be recorded: 1. REC：Event when start recording by press “REC” key. 2. PWR：System will event up from power interruption after restarting. 3. ALM：When external alarm was triggered, event up with alarm number. 4.
h 7 8 9 SLAVE HDD CAPACITY N/A The slave HDD capacity sign will be indicated in left on the screen, It can’t be revised. HDD N/A is with no HDD. SLAVE HDD LEFT RATIO N/A The slave HDD left ratio sign will be indicated in left on the screen, It can’t be revised. HDD N/A is with no HDD. SLAVE HDD FORMAT Same with MASTER HDD FORMAT. EXIT Escape from the HDD MANAGEMENT menu. 8. LOAD DEFAULT Use the “◄ or ►” button to return to the factory default.
CHAPTER 4 OPERATION PROCEDURES 1 Getting Started with your machine Please assure the following instructions before you switch on the machine: 1.1 Voltage check: Before power cable is connected, please check the voltage of this appliance against the supply. Input voltage range 90~260V, frequency range 57-63Hz. CAUTION - Damage would be caused if incorrect power voltage applied. 1.2 Hard Disk connection: Make sure the 40-Pin Hard Disk Data cable and the 4-Pin power connectors are properly connected.
z “REW” or “FF*2/4/6” sign will be indicated in top left corner on the screen. Press Pause button to pause (field by field) for forward. This function can be used in full screen and quad mode (If you choose QUAD in recording mode than it can’t playback in full screen). z “PAUSE” sign will be indicated in top left corner on the screen. Press the STOP button to leave playback mode and resume the Live Mode.
5 Backup The DVR support 2 methods for backing up: 1. VCR Backup The DVR Provides composite signal output for back-up use. You can keep the Image data, and simply just connected BNC connector, at the Back Panel of, with MONITOR OUT Connector. Press VCR REC button, after decided what recording data need to keep, during Play-Back Mode. 2. Compact Flash (CF) Card Backup After the insertion of CF card, network function will be temporary suspended.
playback mode. The screen will start showing BACKUP TO CF CARD AVI FILE on top of the screen for around 1 second and then appear AVI message in the left bottom screen which is indicating DVR system is currently backing up video into buffer. Press “COPY” key again to terminated video backup on your ideal period, the screen will show up CF CARD PROCESSING PLEASE WAIT .. . It takes around 1 min to save AVI file into CF card, it depend on how big the file will be.
triggered during schedule “A” period. Terminal connector： Pin 1-4 ----- ALARM1-ALARM4，Camera alarm input. GND ----- GND N.C ----- Relay N.C，Alarm output N.C COM ----- Relay COM N.O 8 ----- Relay N.O，Alarm output N.O Network Network function is optional, please ensure that you have proper DVR model for network installation. Network setup in this DVR can be done only by TCP/IP network remote computer. With network function the DVR will support remote recording and remote surveillance.
CHAPTER 5 RECORDING TIME LENGTH Recording time length is related to recording speed and recording quality. Tables below are offered for your reference. Record Mode=MUX Record Mode=QUAD Recording length under quad mode will shorter than multiplex mode and PAL will shorter than NTSC. 80GB H.D.
CHAPTER 6 HARD DRIVE INSTALLATION PROCEDURES 1. Hard drive jumpers need to be set properly in order to make DVR function correctly. 2. Instructions below are for second hard drive installation. If you prefer to have only one drive, please ignore instruction below. Remove DVR top cover by taking out screws from location shown below: ① . ② ③ ④ ⑤ ⑥ 3. Below picture indicates DVR which one without a H.D.D installed. 4.
5. Hooking up IDE cable and power cable to the hard drive as picture below, please take a note on that the red line on IDE cable must be next to power cable in order to have correct instillation. 6. This DVR supports maxima 2 hard drives, please take a note on cable length that you use to hook up with the hard drive. 7. Restore top cover then hook up with power and monitor a hard drive status message will appear if it’s been installed successful. Attentions： 1.
