User Manual
Table Of Contents
- Important safety instructions
- What you need to know about safety instructions
- California Proposition 65 Warning
- For your safety
- Induction cooktop elements
- Electrical Safety
- Child safety
- Oven
- Remote Operation
- Self-cleaning ovens
- Ventilating hood
- Glass/Ceramic cooking surfaces
- Critical installation warnings
- Critical usage warning
- Usage cautions
- Critical cleaning warnings
- Introducing your new range
- Before you begin
- Surface cooking
- About induction cooktop cooking
- How to set the appliance for cooktop cooking
- Before using the cooktop
- Cookware for induction cooking zones
- Using the correct size cookware
- Pot and pan sizes
- Induction cookware test
- Operating noises
- Using suitable induction cookware
- Temperature detection
- Suggested settings for cooking specific foods
- Protecting the cooktop
- Operating the oven
- The oven control panel
- Oven lock
- Setting the clock
- Setting the kitchen timer
- Timed cooking
- Delay start
- Turning the oven light on and off
- Minimum and maximum settings
- Using the oven racks
- Baking
- Broiling
- Using the special fuction
- Using the keep warm feature
- Using the smart control feature
- Using the voice control
- Using the options function
- Using the Sabbath feature
- Maintaining your appliance
- Troubleshooting
- Warranty (U.S.A)
- Warranty (CANADA)
- Appendix
English 41
Operating the oven
Sound On/Off
Using Sound On/OFF, you can set the oven controls to operate silently.
How to turn the sound on or off
1. Press
Options for 3 seconds.
2. Press or to select 4, and then press START/SET.
3. Press or to select ON or OFF.
4. Press START/SET to save the changes.
Wi-Fi On/Off
You can turn the range’s Wi-Fi connection on or off.
How to turn the Wi-Fi on or off
1. Press
Options for 3 seconds.
2. Press or to select 5, and then press START/SET.
3. Press or to select ON or OFF.
4. Press START/SET to save the changes.
NOTE
When you turn the range’s Wi-Fi connection off, users can’t set to easy setup.
Demo mode
This option is for use by retail establishments for display purposes only.
(The heating element does not operate).
How to enable or disable the demo mode
1. Press
Options for 3 seconds.
2. Press or to select 0, and then press START/SET.
3. Press or to select ON or OFF.
4. Press START/SET to save the changes.
Temp Adjust
The temperature in the oven has been calibrated at the factory. When rst using
the oven, be sure to follow recipe times and temperatures. If you think the oven is
too hot or too cool, you can correct the temperature in the oven. Before correcting,
test a recipe by using a temperature setting that is higher or lower than the
recommended temperature. The baking results should help you to decide how
much of an adjustment is needed.
The oven temperature can be adjusted ±35 °F (±19 °C ).
How to correct the oven temperature
1. Press
Options for 3 seconds.
2. Press or to select 1, and then press START/SET.
3. Press or to select the desired temperature you want to adjust. (-35
~
35)
4. Press START/SET to save the changes.
NOTE
This adjustment will not affect the broiling or the self-cleaning temperatures. The
adjustment will be retained in memory after a power failure.
Temp Unit (Fahrenheit or Celsius temperature selection)
You can program the oven control to display the temperature in Fahrenheit or
Celsius. The oven has been preset at the factory to display in Fahrenheit.
How to change the display from Fahrenheit to Celsius or Celsius to Fahrenheit
1. Press Options for 3 seconds.
2. Press or to select 2, and then press START/SET.
3. Press or to select F (Fahrenheit) or C (Celsius).
4. Press START/SET to save the changes.
12-hour energy saving
If you accidently leave the oven on, this feature will automatically turn off the
oven after 12-hours during baking functions or after 3 hours during a broil
function. (Default setting : on)
How to turn the 12-hour energy saving feature on or off
1. Press
Options for 3 seconds.
2. Press or to select 3, and then press START/SET.
3. Press or to select --Hr (Off) or 12Hr (On).
4. Press START/SET to save the changes.










