2/21/05 12:31 AM Page 17 USER’S MANUAL Function Contrller RUSSIAN E§§HNIKA System Air Conditioner DEUTSCH PORTUGUÊS ITALIANO FRANÇAIS ESPAÑOL MCM-A100 ENGLISH Function Controller IB_E<05164 E S F I P D G R A DB98-05164A(3)
Safety Precautions ● Before using the function controller, read carefully this instructions. reading the instructions, keep this owner's instructions and the installation manual in a handy and safe place. If a user is changed, you must hand over the manuals. ● Never attempt to install the air conditioning system or to move the function controller by yourself. ● After WARNING CAUTION E-2 ◆ Do not attempt to install or repair this function controller by yourself.
ENGLISH Contents ◆ VIEW OF THE FUNCTION CONTROLLER 4 ◆ GETTING START 5 ◆ SELECTING THE INDOOR UNIT 6 ◆ SELECTING THE AUTOMATIC OPERATING MODE 7 ◆ COOLING YOUR ROOM 8 ◆ HEATING YOUR ROOM 10 (EXCEPT COOLING ONLY MODELS) ◆ REMOVING EXCESS HUMIDITY 12 ◆ AIRING YOUR ROOM 14 ◆ ADJUSTING THE AIR FLOW DIRECTION 15 (EXCEPT DUCT TYPE) E-3
View of the Function Controller The function controller is an additional controller which is used with the centralized controller.
ENGLISH Getting Start You have just purchased a function controller and it has been installed by your installation specialist. Your Owner’s Instructions contain much valuable information on using your function controller. Please take the time to read them as they will help you take full advantage of the unit’s features. In the main part of the document, you will find a series of step-by-step procedures for each function available.
Selecting the Indoor Unit You can control a specific indoor unit from the function controller. 1 Select an indoor unit you want to control by pressing button. button, the room Result: : ◆ Each time you press number is increased by 1, and each time you press button, the room number is decreased by 1 from 0~15. 2 Turn the air conditioner on by pressing button. Result: 3 E-6 (ON/OFF) ◆ The On/Off indicator on the function controller comes on.
ENGLISH Selecting the Automatic Operating Mode In the Automatic mode, the room temperature and the fan speed are controlled automatically. 1 If necessary, press (ON/OFF) button. Result: : ◆ The On/Off indicator on the function controller comes on. ◆ The air conditioner runs in the mode selected when the unit was last used.
Cooling Your Room You must select the COOL mode if you wish to adjust the : ◆ Cooling temperature ◆ Fan speed when cooling 1 If necessary, press (ON/OFF) button. Result: : ◆ The On/Off indicator on the function controller comes on. ◆ The air conditioner runs in the mode selected when the unit was last used.
ENGLISH 3 To adjust the temperature, press the Temperature buttons one or more times until the required temperature is displayed. Possible temperatures are between 18°C and 30°C inclusive. Result: 4 ◆ Each time you press Temperature buttons: - The temperature is adjusted by 1°C. ◆ The air conditioner starts cooling, provided that the room temperature is higher than the selected temperature ; the fan will, however, operate.
Heating Your Room (Except Cooling Only Models) You can select the HEAT mode only in heat pump models. You must select the HEAT mode if you wish to adjust the : ◆ Heating temperature ◆ Fan speed when heating 1 If necessary, press (ON/OFF) button. Result: : ◆ The On/Off indicator on the function controller comes on. ◆ The air conditioner runs in the mode selected when the unit was last used.
ENGLISH 3 To adjust the temperature, press the Temperature buttons one or more times until the required temperature is displayed. Possible temperatures are between 16°C and 30°C inclusive. Result: 4 ◆ Each time you press Temperature buttons: - The temperature is adjusted by 1°C. ◆ The air conditioner starts heating, provided that the room temperature is lower than the selected temperature ; the fan will, however, operate.
Removing Excess Humidity If the atmosphere in your room is very humid or damp, you can remove excess humidity without lowering the room temperature too much. 1 If necessary, press (ON/OFF) button. Result: : ◆ The On/Off indicator on the function controller comes on. ◆ The air conditioner runs in the mode selected when the unit was last used.
ENGLISH 3 To adjust the temperature, press the Temperature buttons one or more times until the required temperature is displayed. Possible temperatures are between 18°C and 30°C inclusive. Result: : ◆ Each time you press Temperature buttons: - The temperature is adjusted by 1°C. ◆ The air conditioner starts removing the excess humidity. The quantity of air is adjusted automatically. 4 To control the direction of the air flow, refer to page 15.
Airing Your Room If the atmosphere in your room is stale, you can air it using the FAN feature. 1 If necessary, press (ON/OFF) button. Result: : ◆ The On/Off indicator on the function controller comes on. ◆ The air conditioner runs in the mode selected when the unit was last used. IMPORTANT 2 The air conditioner is fitted with a protection mechanism to prevent the unit from being damaged when it is started immediately after being: ◆ Plugged in ◆ Stopped It will start up normally after three minutes.
ENGLISH Adjusting the Air Flow Direction (Except Duct Type) Depending on the position of the indoor unit, you can adjust the position of the air flow blade, thus increasing the efficiency of the air conditioner. 1 Press the Swing button. Result: The blade is moving between up and down. IMPORTANT 2 When the air conditioner is first turned on, the blade is moved. To stop the blade, press the Swing button again.
Function Controller IB_E<05164 2/21/05 12:31 AM Page 16 ELECTRONICS
