SyncMaster 275TPLUS Install driver Install programs
Notation Failure to follow directions noted by this symbol could result in bodily harm or damage to the equipment. Prohibited Important to read and understand at all times Do not disassemble Disconnect the plug from the outlet Do not touch Ground to prevent an electric shock Power When not used for extended period of time, set your computer to DPM. If using a screen saver, set it to active screen mode. The images here are for reference only, and are not applicable in all cases (or countries).
Do not use a damaged or loose plug. This may cause electric shock or fire. Do not pull the plug out by the wire nor touch the plug with wet hands. This may cause electric shock or fire. Use only a properly grounded plug and receptacle. An improper ground may cause electric shock or equipment damage. (Class l Equipment only.) Insert the power plug firmly so that it does not come loose. A bad connection may cause fire.
To disconnect the apparatus from the mains, the plug must be pulled out from the mains socket, therefore the mains plug shall be readily operable. This may cause electric shock or fire. Installation Be sure to contact an authorized Service Center when installing your set in a location with heavy dust, high or low temperatures, high humidity, and exposed to chemical substances and where it will be operated for 24 hours continuously such as at airports, train stations etc.
Otherwise, this may cause fire. Keep any heating devices away from the power cable. A melted coating may cause electric shock or fire. Do not install the product in places with poor ventilation, for instance, a bookshelf, closet, etc. Any increase in the internal temperature may cause fire. Put down the monitor carefully. Failing to do so may damage the monitor. Do not place the monitor face down. This may damage the TFT-LCD surface.
Cleaning and Using When cleaning the monitor case or the surface of the TFT-LCD screen, wipe with a slightly moistened, soft fabric. Do not spray water or detergent directly onto the monitor. This may cause damage, electric shock or fire. Use the recommended detergent with a smooth cloth. If the connector between the plug and the pin is dusty or dirty, clean it properly using a dry cloth. A dirty connector may cause electric shock or fire. Make sure to unplug the power cord before cleaning the product.
If your monitor does not operate normally - in particular, if there is any unusual sound or smell coming from the monitor - contact an authorized dealer or the Service Center. This may cause electric shock or fire. Keep the product away from places exposed to oil, smoke or moisture; do not install inside a vehicle. This may cause a malfunction, electric shock or fire. In particular, avoid operating the monitor near water or outdoors where the monitor could be exposed to snow or rain.
Keep the product away from combustible chemical sprays or inflammable substances. This may cause an explosion or fire. Never insert anything metallic into the monitor openings. This may cause electric shock, fire or injury. Do not insert metal objects such as chopsticks, wire and tools or inflammable objects such as paper or matches into the vent, headphone port or AV ports or etc or etc. This may cause electric shock or fire.
When moving the monitor, turn off and unplug the power cord. Make sure that all cables, including the antenna cable and cables connected to other devices, are disconnected before moving the monitor. Failure to disconnect cables may damage it and cause fire or electric shock. Place the product out of children’s reach, as they could damage by hanging onto it. A falling product may cause injury to the person or even fatality.
Correct Disposal of This Product (Waste Electrical & Electronic Equipment) - Europe only (Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life.
PRODUCT INFORMATION (Image Retention Free) LCD Monitors and TVs may have an image retention when switching from one image to another especially after displaying a stationary image for a long time. This guide is to demonstrate a correct usage of LCD products in order to protect them from Image retention. Warranty Warranty does not cover any damage caused by image retention. Burn-in is not covered by the warranty.
Ex) The best way to protect your monitor from Image retention is to set your PC or System to operate a Screen Saver program when you are not using it. Image retention may not occur when a LCD panel is operated under normal conditions. Normal conditions are defined as continuously changing video patterns. When the LCD panel is operated for a long time with a fixed pattern (-over 12 hours-), there may be slight difference in voltage between electrodes that work the liquid crystal (LC) in a pixel.
Package Contents Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Contact a local dealer to buy optional items.
Quick Setup Guide Warranty Card (Not available in all locations) User's Guide, Monitor Driver, Natural Color, MagicTune™ Cable Power Cord D-sub Cable USB Cable Others Cleaning Cloth This is only provided for highly polished black products as a product feature.
Front MENU button [ Adjust buttons [ ] Opens the OSD menu. Also use to exit the OSD menu or return to the previous menu. ] PC/DVI(PC) : MagicBright™ button [ ] These buttons allow you to adjust items in the menu. MagicBright™ is a new feature providing optimum viewing environment depending on the contents of the image you are watching. Currently seven different modes are available: Custom, Text, Internet, Game, Sports, Movie and Dynamic CR. Each mode has its own pre-configured brightness value.
Select this mode to view a sharper image than in "Standard" mode. 2) Standard Select this mode when the surroundings are bright. This also provides a sharp image. 3) Movie Select this mode when the surroundings are dark. This will save power and reduce eye fatigue. 4) Custom Select this mode when you want to adjust the image according to your preferences. >> Click here to see an animation clip Brightness button [ ] When OSD is not on the screen, push the button to adjust brightness.
The configuration at the back of the monitor may vary from product to product. POWER S/W / POWER POWER S/W : Switch the monitor on and off. POWER : Connect the power cord for your monitor to the POWER port on the back of the monitor. HDMI IN / DVI IN(HDCP) / RGB IN HDMI IN : Connect the HDMI IN terminal at the back of your monitor to the HDMI terminal of your digital output device using a HDMI cable. DVI IN(HDCP) : Connect the DVI cable to the DVI IN(HDCP) port on the back of your monitor.
Kensington Lock z The Kensington lock is a device used to physically fix the system when using it in a public place. (The locking device has to be purchased separately.) For using a locking device, contact where you purchase it. Stand Stopper z Remove the fixing pin on the stand to lift the monitor up and down. See Connecting Cables for further information regarding cable connections.
Connecting Cables Connect the power cord for your monitor to the POWER port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. Use a connection appropriate for your computer. Using the RGB (Analog) connector on the video card. - Connect the signal cable to the 15-pin, RGB IN port on the back of your monitor. [ RGB IN ] Using the DVI (Digital) connector on the video card. - Connect the DVI cable to the DVI IN(HDCP) port on the back of your monitor.
The USB port of the monitor supports High-Speed Certified USB 2.0. High speed Full speed Low speed Data Rate 480 Mbps 12 Mbps 1.5 Mbps Power Consumption 2.5 W (Max., each port) 2.5 W (Max., each port) 2.5 W (Max., each port) Connect the To use UP port of the monitor and the USB port of the computer with the USB cable. DOWN port, you have to connect the UP (Upstream Cable) to the PC.
Connecting a Speaker When connecting a speaker, be careful that the grooves of the monitor and the speaker . ( )are aligned with each other. Adjust the aligned positions until you hear a ‘click’. If a speaker is connected correctly, you can hear a ‘click’.If a speaker is connected without you hearing a ‘click’, the holding part may become damaged. If you need to separate, please pull ( ) a little and push to the right.
Connect a headphone to the black terminal at the right of the speaker. Connect a microphone to the red terminal at the right of the speaker. By turning part ( + , - ) in the direction shown in the figure below, the speaker turns on and the volume increases. Connect the power line connected to the speaker to the black terminal of the monitor. This speaker is not connected to an external power source. It is connected to a monitor for the required power.
Connect the VIDEO OUT port of the DVD / DTV Set-Top Box to the PR, PB, Y input ports using a component video cable (PR, PB, Y). Then, start the DVD with a DVD disc inserted. Select Component using the ' ' button. To hear sound, refer to the Connection section of your conncted external device manual . Connecting HDMI You cannot connect a PC to the HDMI IN terminal. Input devices such as digital DVD are connected to the HDMI IN terminal of the monitor using the HDMI cable.
Sliding stand Stand Stopper Swivel stand Using ( ),You can swivel the monitor left and right at an angle of 350° to set the monitor lengthwise. The rubber under the stand is to avoid the monitor slide. When you try to rotate the monitor in the state of the power cord or cable connecting to the monitor, the power cord of cable can be destroyed.
Using ( ), You can adjust the tilt anlgle within a range of 3° forward to 25° backward for the most comfortable viewing angle. Attaching a Base This monitor accepts a 200 mm x 100 mm VESA-compliant Mounting interface pad. Monitor Mounting interface pad (Sold separately) 1. Turn off your monitor and unplug its power cord. 2. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen. 3. Remove four screws and then remove the stand from the LCD monitor. 4.
z z z z z z inside of the Monitor. For wall mounts that do not comply with VESA standard screw specifications, the length of the screws may differ depending on their specifications. Do not use screws that do not comply with the VESA standard screw specifications. Do not fasten the screws too tightly, as this may damage the product or cause the product to fall, leading to personal injury. Samsung is not liable for these kinds of accidents.
Monitor Driver When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions appropriate for the operating system you have. Prepare a blank disk and download the driver program file at the Internet web site shown below. Internet web site :http://www.samsung.com/ (Worldwide) http://www.samsung.com/monitor (U.S.A) http://www.sec.co.kr/monitor (Korea) http://www.
This monitor driver is under certifying MS logo, and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage http://www.samsung.com/ Monitor driver installation is completed. Installing the Monitor Driver (Manual) Windows Vista | Windows XP | Windows 2000 | Windows ME | Windows NT | Linux Microsoft® Windows Vista™ Operating System Insert your Manual CD into your CD-ROM drive. Click (Start) and "Control Panel".
Click "Properties" in the "Monitor" tab. If the "Properties" button is deactivated, it means the configuration for your monitor is completed. The monitor can be used as is. If the message “Windows needs…” is displayed, as shown in the figure below, click "Continue". This monitor driver is under certifying MS logo, and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage http://www.samsung.com/ Click "Update Driver…" in the "Driver" tab.
Click "Have Disk…" and select the folder (for example, D:\Drive) where the driver setup file is located, and click "OK". Select the model that matches your monitor from the list of monitor models on the screen, and click "Next". Click "Close"→ "Close" → "OK" → "OK" on the following screens displayed in sequence. Microsoft® Windows® XP Operating System Insert the CD into the CD-ROM drive. Click "Start" → "Control Panel" then click the "Appearance and Themes" icon.
Click "Display" icon and choose the "Settings" tab then click "Advanced." Click the "Properties" button on the "Monitor" tab and select "Driver" tab. Click "Update Driver." and select "Install from a list or." then click the "Next" button. Select "Don't search ,I will." then click "Next" and then click "Have disk".
Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next" button. If you can see following "Message" window, then click the "Continue Anyway" button. Then click the "OK" button. This monitor driver is under certifying MS logo, and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage http://www.samsung.com/ Click the "Close" button then click the "OK" button continually.
Monitor driver installation is completed. Microsoft® Windows® 2000 Operating System When you can see "Digital Signature Not Found" on your monitor, follow these steps. Choose the "OK" button on the "Insert disk" window. Click the "Browse" button on the "File Needed" window. Choose A:(D:\Driver) then click the "Open" button and then click the "OK" button. How to install Click "Start," "Setting," and then "Control Panel." Double click the "Display" icon.
In the Display Registration Information window, click the Settings tab and then click "All Display Modes". Select a mode that you wish to use (Resolution, Number of colors and Vertical frequency) and then click "OK". Click the "Apply" button if you see the screen working normally after clicking "Test". If the screen is not normal, change to a different mode (lower mode of resolution, colors, or frequency).
Insert the CD included with the Samsung monitor into the CD-ROM Drive. The initial Natural Color screen will appear. Click on Natural Color in the startup window to install the Natural Color software. To install the program manually, insert the CD included with the Samsung monitor into the CD-ROM Drive, click the Windows [Start] button, select [Run...] . Enter D:\Color\NCProSetup.exe and then press the key. (If the drive where the CD is inserted is not D:\, enter the applicable drive.
z z 32MB Memory above 60MB Hard disk space above * For more information, visit the MagicTune™ website. Uninstall The MagicTune™ program can be removed only by using the "Add or Remove Programs" option of the Windows® Control Panel. Perform the following steps remove MagicTune™. 1. Go to [Task Tray] ' [Start] ' [Settings] and select [Control Panel] in the menu. If the program runs on Windows® XP, go to [Control Panel] in the [Start] menu. 2. Click the "Add or Remove Programs" icon in Control Panel. 3.
Control Buttons Use this button to open the on-screen menu and exit from the menu screen or close screen adjustment menu. PC/DVI(PC) : MagicBright™ MagicBright™ is a new feature providing the optimum viewing environment depending on the contents of the image you are watching. Then press the button again to circle through available preconfigured modes.
This button allows you to adjust items in the menu. When OSD is not on the screen, push the button to adjust brightness. Press this button to activate a highlighted menu item. Selects the input signal while the OSD is off. Press to self-adjust to the incoming Analog signal. The values of fine,coarse and position are adjusted automatically. AUTO PIP Push the PIP button to turn PIP On/Off.
OSD Lock & Unlock When pressing the AUTO or PIP button after locking the OSD When pressing the MENU button after locking the OSD Menu Description This is the function that locks the OSD in order to keep the current states of settings or prevent others from adjusting the current settings. Locked Lock : Hold down the menu button for more than five (5) seconds to activate the OSD adjustment lock function.
Though the OSD adjustment lock function is activated, you can still adjust the brightness and contrast, and adjust MagicBright ( ) using the Direct button. MagicBright™ Menu MagicBright™ /Mode Description PC/DVI(PC) : MagicBright™ MagicBright™ is a new feature providing the optimum viewing environment depending on the contents of the image you are watching. Then press the button again to circle through available preconfigured modes.
Menu Description Brightness When OSD is not on the screen, push the button to adjust brightness. SOURCE Menu SOURCE Description Selects the input signal while the OSD is off. (When the source button is pressed to change the input mode, a message appears in the upper left of the screen displaying the current mode -- PC, DVI, AV, S-Video and , Component and HDMI input signal.
Changing the source is only allowed for external devices that are connected to the monitor at the time. PIP ( Available in PC/DVI(PC) Mode Only ) Menu PIP OSD Function Input Description Push the PIP button to turn PIP screen On/Off. You can view a picture from AV, S-Video, or Component through the PIP screen in PC and DVI (PC) mode.
The default setting may different depending on the selected Input Mode (input signal source selected in External Input List) and the selected resolution. Menu Description Play/Stop Use to select PC or other external input sources connected to the Monitor. Use to select the screen of your choice. Source List 1) PC 2) DVI 3) AV 4) S-Video 5) Component 6) HDMI MENU → → → , → Name the input device connected to the input jacks to make your input source selection easier.
The default setting may different depending on the selected Input Mode (input signal source selected in External Input List) and the selected resolution. Menu Description Play/Stop MagicBright™ is a new feature providing optimum viewing environment depending on the contents of the image you are watching. Currently seven different modes are available : Custom, Text, Internet, Game, Sport, Movie and Dynamic CR. Each mode has its own pre-configured brightness value.
Custom 2) Brightness : Adjust the Brightness. - Not available in MagicBright™ mode of Dynamic CR. MENU → , → → , → → , → → , Brightness → If you adjust picture using Custom function, MagicBright™ will turn to Custom mode. Image Lock is used to fine-tune and get the best image by removing noise that creates unstable images with jitter and shimmer. If satisfactory results are not obtained using the Fine adjustment, use the Coarse adjustment and then use Fine again.
Picture (AV/S-Video/Component/HDMI) The default setting may different depending on the selected Input Mode (input signal source selected in External Input List) and the selected resolution. Menu Description Play/Stop The Monitor has four automatic picture settings ("Dynamic", "Standard", "Movie" and "Custom") that are preset at the factory. You can activate either Dynamic, Standard, Movie, or Custom. You can select "Custom" which automatically recalls your personalized picture settings.
MENU → , → → , → → , → → , → You can switch the Size. Size z z AV / S-Video : Wide / 16:9 / Zoom1 / Zoom2 / 4:3 Component / HDMI : Wide / 16:9 / 4:3 MENU → Film Mode , → → , → → , → You can turn Film Mode Off / On. The Film Mode feature offers you a theater-quality viewing experience. In Component mode, film mode is only available for 480i and 576i input. MENU → , → → , → → , → MagicColor Pro - Not available in MagicBrightT mode of Dynamic CR.
depending on your taste. If this is the case, adjust the Picture and Color menu by using the OSD to fit your eyes. MENU → Color Tone → , → , → → , → → , → , → → , → → , → Gamma correction changes the luminance of the colors with intermediate luminance. Increased Mode number - Displays the full screen more naturally and softer and sharpens the dark scale. Decreased Mode number - Displays the full screen sharper and improves the bright scale.
The default setting may different depending on the selected Input Mode (input signal source selected in External Input List) and the selected resolution. Menu Description Turn the PIP Screen on or off. You can view a picture from AV, S-Video, or Component through the PIP screen in PC and DVI mode. PIP 1) Off 2) On MENU → Source , → → → , → Select the input source for the PIP. You can view a picture from AV, S-Video, or Component through the PIP screen in PC and DVI(PC) mode.
The default setting may different depending on the selected Input Mode (input signal source selected in External Input List) and the selected resolution. Menu Description You can choose one of 11 languages. Language MENU → , → → → , → Changes the opaqueness of the background of the OSD.
- The Screen Scroll function scrolls the screen for the specified period of time. - This function is not available when the power is turned off. Safety Screen 1) Safety Screen : Determines whether to turn the Screen Scroll function Off or On. 2) Interval : Determines the time interval to run the Screen Scroll operation. (1~10 Hour) The time is calculated on the basis of the power on time. 3) Second : Determines the time period to run the Screen Scroll operation.
Check List Before calling for service, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the Information section or contact your dealer. Symptom No images on the screen. I cannot turn on the monitor. Check List Solutions Is the power cord connected properly? Check the power cord connection and supply.
There is no image on the screen. Is the power indicator on the monitor blinking at 1 second intervals? The monitor is in PowerSaver mode. Connected using the DVI cable? You may get a blank screen if you boot the system before you connect the DVI cable, or disconnect and then reconnect the DVI cable while the system is running as certain types of graphic cards do not send out video signals. Connect the DVI cable and then reboot the system.
Has the video card been set properly? Set the video card by referring to the video card manual. There is a message that reads "Unrecognized monitor, Plug & Play (VESA DDC) monitor found". Have you installed the monitor driver? Install the monitor driver according to the Driver Installation Instructions. See the video card manual to see if the Plug & Play (VESA DDC) function can be supported. Install the monitor driver according to the Driver Installation Instructions.
Note that video card support can vary, depending on the version of the driver used. (Refer to the computer or the video card manual for details.) How can I adjust the resolution? Windows XP : Set the resolution at the Control Panel → Appearance and Themes → Display → Settings. Windows ME/2000 : Set the resolution at the Control Panel → Display → Settings. Contact the video card manufacturer for details.
monitor. If your monitor screen remains blank after using the previous procedure, check your video controller and computer system; your monitor is functioning properly. Warning Messages If there is something wrong with the input signal, a message appears on the screen or the screen goes blank although the power indicator LED is still on. The message may indicate that the monitor is out of scan range or that you need to check the signal cable.
Specifications General Model Name SyncMaster 275TPLUS LCD Panel Size 27" Wide Diagonal (68 cm) Display area 581.76 mm(H) x 363.6 mm(V) Pixel Pitch 0.303 mm(H) x 0.303 mm(W) Synchronization Horizontal 30 ~ 81 kHz Vertical 56 ~ 75 Hz Display Color 16.7 M Resolution Optimum resolution 1920x1200 @ 60 Hz (RB) Maximum resolution 1920x1200 @ 60 Hz (RB) For the detailed timing mode of each mode, refer to Preset Timing Modes.
AC 100-240 VAC ( ± 10 %), 60/50 Hz ± 3 Hz Signal Cable 15pin-to-15pin D-sub cable, Detachable DVI-D to DVI-D connector, Detachable (Sold separately) Dimensions (W x H x D) / Weight 629.0 X 410.5 X 81.0 mm / 24.8 x 16.2 x 3.2 inch (Without Stand) 629.0 X 486.0 X 280.0 mm / 24.8 x 19.1 x 11.0 inch (With Stand) / 10.4 kg / 22.
Power Indicator Blue Blue Blinking Black Power Consumption Less than 130 watts Less than 2 Watts Less than 0 Watts This monitor is EPA ENERGY STAR® compliant and ENERGY2000 compliant when used with a computer equipped with VESA DPM functionality. As an ENERGY STAR® Partner, SAMSUNG has determined that this product meets the ENERGY STAR® guidelines for energy efficiency.
1024 VESA, 1280 x 1024 79.976 75.025 135.000 +/+ VESA, 1600 x 1200 75.000 60.000 162.000 +/+ VESA, 1920 x 1200 74.038 59.950 154.000 +/- Horizontal Frequency The time to scan one line connecting the right edge to the left edge of the screen horizontally is called Horizontal Cycle and the inverse number of the Horizontal Cycle is called Horizontal Frequency.
Contact SAMSUNG WORLDWIDE If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center. North America U.S.A 1-800-SAMSUNG (726-7864) http://www.samsung.com/us CANADA 1-800-SAMSUNG (726-7864) http://www.samsung.com/ca MEXICO 01-800-SAMSUNG (726-7864) http://www.samsung.com/mx ARGENTINE 0800-333-3733 http://www.samsung.com/ar BRAZIL 0800-124-421 4004-0000 http://www.samsung.com/br CHILE 800-SAMSUNG(726-7864) http://www.samsung.
Europe AUSTRIA 0800-SAMSUNG(726-7864) www.samsung.com/at BELGIUM 0032 (0)2 201 24 18 http://www.samsung.com/be CZECH REPUBLIC 844 000 844 http://www.samsung.com/cz DENMARK 70 70 19 70 http://www.samsung.com/dk FINLAND 030-6227 515 http://www.samsung.com/fi FRANCE 3260 SAMSUNG(726-7864) 08 25 08 65 65 (€ 0,15/Min) http://www.samsung.com/fr GERMANY 01805-SAMSUNG(726-7864) (€ 0,14/Min) http://www.samsung.de HUNGARY 06-80-SAMSUNG(726-7864) http://www.samsung.
UZBEKISTAN 8-800-120-0-400 http://www.samsung.uz AUSTRALIA 1300 362 603 http://www.samsung.com/au CHINA 800-810-5858, 010- 6475 1880 http://www.samsung.com.cn HONG KONG 3698-4698 http://www.samsung.com/hk INDIA 3030 8282 1800 110011 http://www.samsung.com/in INDONESIA 0800-112-8888 http://www.samsung.com/id JAPAN 0120-327-527 http://www.samsung.com/jp MALAYSIA 1800-88-9999 http://www.samsung.com/my NEW ZEALAND 0800SAMSUNG(726-7864) http://www.samsung.
Interlace and Non-Interlace Methods Showing the horizontal lines of the screen from the top to the bottom in order is called the NonInterlace method while showing odd lines and then even lines in turn is called the Interlace method. The Non-Interlace method is used for the majority of monitors to ensure a clear image. The Interlace method is the same as that used in TVs.
If there's still noise after automatic adjustment, use FINE/COARSE adjustment function. If you view a fixed screen for an extended period of time, residual image or blurriness may appear. Change the mode to energy save or set a screensaver to move the picture when you need to be away from the monitor for an extended period of time. Authority Information in this document is subject to change without notice. © 2007 Samsung Electronics Co., Ltd. All rights reserved.
