SyncMaster LD190/LD190G/LD220/LD220G LCD Monitor User Manual
Safety Instructions Notational Note These safety instructions must be followed to ensure your safety and prevent property damage. Make sure to read the instructions carefully and use the product in the correct manner. Warning / Caution Otherwise, it may result in death or personal injury. Otherwise, it may result in personal injury or property damage.
Safety Instructions Ensure that the power plug is plugged into the power outlet firmly and correctly. • Otherwise, this may result in fire. Do not forcefully bend or pull the power plug and do not place any heavy material on it. • Otherwise, this may result in fire. Do not connect multiple appliances to the same power outlet. • Otherwise, this may cause fire due to overheating. Do not disconnect the power cord while using the product.
Safety Instructions Keep heating appliances as far away from the power cord or the product as possible. • Otherwise, this may result in electric shock or fire. Do not install it in a badly ventilated location such as a bookcase or closet. • Otherwise, this may result in fire due to an increase in the internal temperature. Put down the monitor carefully. • Failing to do so may damage the monitor. Do not place the front of the product on the floor.
Safety Instructions When cleaning the product, disconnect the power cord and clean it softly with a dry cloth. • (Do not use chemicals such as wax, benzene, alcohol, thinner, mosquito repellant, lubricant, or cleaner.) These may change the appearance of the product surface and peel off the indication labels on the product. Since the product housing is easily scratched, make sure to use the specified cloth only. • Use the specified cloth adding only a little water.
Safety Instructions Do not lift or move the product back and forwards or right and left while only holding the power cord or signal cables. • Otherwise, it may fall and result in electric shock, damage to the product or fire due to damage to the cable. Make sure that the ventilating opening is not blocked by a table or curtain. • Otherwise, it may result in fire due to an increase in the internal temperature.
Safety Instructions • If you use the product in a location exposed to vibrations, it may damage the product and result in fire. When moving the product, turn the power off and disconnect the power plug, antenna cable, and all the cables connected to the product. • Otherwise, it may result in electric shock or fire. Ensure that children do not hang onto the product or climb up onto the product. • The product may fall and cause personal injury or death.
Safety Instructions Do not install the product in a location low enough for children to reach. • Otherwise, it may fall and result in personal injury. • Since the front part of the product is heavy, install the product on a level and stable surface. Do not put any heavy objects on the product. • This may result in personal injury and/or damage to the product. Good Postures When Using the Monitor When using the product, use it in the correct position.
Introduction {LD190,LD190G}Package Contents Note Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Contact a local dealer to buy optional items.
Introduction Note Cleaning Cloth is only provided for highly polished black products as a product feature. Your Monitor Initial Settings Select the language using the up or down key. The displayed content will disappear after 40 seconds. Turn the Power button off and on. It will be displayed again. It can be displayed up to three (3) times. Make sure to adjust the resolution of your PC before reaching the maximum count.
Introduction When OSD is not on the screen, push the button to adjust brightness. AUTO button When OSD is not on the screen, push the button for auto adjustment. Adjust buttons [ ] These buttons allow you to adjust items in the menu. Power button [ ] Use this button for turning the product on and off. Note See PowerSaver described in the manual for further information regarding power saving functions.
Introduction The Kensington lock is a device used to physically fix the system when using it in a public place. (The locking device has to be purchased separately.) For using a locking device, contact where you purchase it. Note The location of the Kensington Lock may be different depending on its model. Using the Anti-Theft Kensington Lock 1. Insert the locking device into the Kensington slot on the Monitor turn it in the locking direction and . 2. Connect the Kensington Lock cable. 3.
Introduction Cables D-Sub Cable Power Cord USB Cable Others Cleaning Cloth Note Cleaning Cloth is only provided for highly polished black products as a product feature. Your Monitor Initial Settings Select the language using the up or down key. The displayed content will disappear after 40 seconds. Turn the Power button off and on. It will be displayed again. It can be displayed up to three (3) times. Make sure to adjust the resolution of your PC before reaching the maximum count.
Introduction Front Note Touch them lightly with your fingers to use them. MENU button [MENU] Opens the on-screen menu and exits from the menu. Also use to exit the OSD menu or return to the previous menu. Brightness button [ ] When OSD is not on the screen, push the button to adjust brightness. AUTO button When OSD is not on the screen, push the button for auto adjustment. Adjust buttons [ ] These buttons allow you to adjust items in the menu.
Introduction POWER port Connect the power cord for your monitor to the POWER port on the back of the product. USB OUT port DOWN(USB downstream port) Connect the USB cable. DOWN port of the USB monitor and a USB device with the UP(USB upstream port) Connect the UP port of the monitor and the USB port of the computer with the USB cable. USB IN port Connect the USB cable.
Introduction Using the Anti-Theft Kensington Lock 1. Insert the locking device into the Kensington slot on the Monitor turn it in the locking direction . 2. Connect the Kensington Lock cable. 3. Fix the Kensington Lock to a desk or a heavy stationary object. Note See Connecting Cables for further information regarding cable connections.
Connections Monitor connection with D-SUB cable Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. Use a connection appropriate for your computer. Using the D-sub (Analog) connector on the video card. • Connect the signal cable to the 15-pin, D-sub port on the back of your monitor. [RGB IN] Connected to a Macintosh. • Connect the monitor to the Macintosh computer using the D-sub connection cable.
Connections Press the Fn + F4( ) key combination once. Then the 'Easy Display Manager'screen appears in which you can select a display device. ) key while holding down the Fn key, the selected option Whenever you press the F4( is changed. Monitor connection with USB cable Note The monitor can be operated with USB cable connection only. The monitor can be operated with D-sub cable connection as well. Installation Requirements Installation Requirements 1.
Connections (LD220/LD220G models only) Maximum of 4 monitors can be used at a same time with a serial USB connection. Maximum of 6 monitors can be used at a same time with a parallel USB connection. When connecting serially You can connect up to four (4) USB monitors serially. When connecting in parallel You can connect up to six (6) USB monitors in parallel. When connecting external devices to the USB monitor, you can only connect up to four (4) devices.
Connections 3. connecting the monitor to PC with USB cable, the following message (as shown picture) will appear on your PC window in a sequential manner. 4. When installation is completed, a monitor icon is created in the system tray at the bottom of window screen. The installed USB Monitor information is displayed as shown below. 5. When the Driver installation is completed, please set the USB monitor to multi-monitor. • USB Driver online download Please visit the Download Center (http://www.
Connections Mode position: Right hand side of the Main Screen Mode rotation: 0 ° Multi-monitor Configuration Note Both USB monitor (USB Cable connection) and general monitor (D-SUB connection) have same multi-monitor configuration. 1. Click 'Start >Control panel > Appearance and Themes >Display'. 2. Select 'Settings' tab. 3. Click second monitor icon and check 'Extend my windows desktop onto this monitor'. Then click 'Apply' button shown as below. 4.
Connections 2. Click the monitor icon to display a list of connected USB monitors. e.g.,) The following figure shows when two USB monitors are connected. Select the monitor for which you want to configure the display settings. You can configure the "Screen Resolution" , "Color Quality" and "Screen Rotation" settings for your monitor. Note 1. Because this USB monitor is recognized as a USB device, the DOS screen that appears for general monitors when a PC is booting up is not displayed.
Connections 3. • Install the USB driver. • As USB port can be unstable, reboot your PC. • PC's USB port may be faulty. Please try to connect different port. • USB monitor may not work on USB 1.0. • Any input from mouse or keyboard will activate the display if it is under the power saving mode. I can't install USB Driver with the supplied CD. • 4. After installing USB Driver, The computer performance is slow. • 5. Download USB driver at Samsung Electronics website and install it.[ http://www.
Connections 10. I disconnected or turned off my USB monitor but my PC still displays the old monitor information in the Display Properties window. • Deactivated USB monitor is due to either the power is off or there is no USB connection. In order to remove this information, 'Samsung Ubisync Monitor' program must be removed. This can be done by click 'Start' - 'Control Panel' - 'Add/Remove Programs' - 'Samsung Ubisync Monitor' - 'Remove'.
Connections 1. Connect the cable. UP port of the monitor and the USB port of the computer with the USB Note To use DOWN port, you have to connect the UP (Upstream Cable) to the PC. Make sure to use the USB cable supplied with this monitor to connect the monitor's UP port and your computer's USB port. 2. Connect the 3. The use procedures are as the same as those for using an external device connecting to the PC. DOWN port of the USB monitor and a USB device with the USB cable.
Connections Using the Stand Folding the base Note You can tilt the monitor backwards at an angle of 10 °~ 30 ° (±5°) .
Using the Software Monitor Driver Note When prompted by the operating system for the monitor driver, insert the CDROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions appropriate for the operating system you have. Prepare a blank disk and download the driver program file at the Internet web site shown here. Internet web site : http://www.samsung.com/ (Worldwide) Installing the Monitor Driver (Automatic) 1.
Using the Software Note This monitor driver is under certifying MS logo, and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage. http://www.samsung.com/ Installing the Monitor Driver (Manual) Microsoft® Windows Vista™‚ Operating System 1. Insert your Manual CD into your CD-ROM drive. 2. Click (Start) and "Control Panel". Then, double-click on "Appearance and Personalization". 3. Click "Personalization" and then "Display Settings". 4.
Using the Software If the message "Windows needs..." is displayed, as shown in the figure below, click "Continue". Note This monitor driver is under certifying MS logo, and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage. 6. Click "Update Driver..." in the "Driver" tab. 7. Check the "Browse my computer for driver software" checkbox and click "Let me pick from a list of device drivers on my computer". 8. Click "Have Disk...
Using the Software 9. Select the model that matches your monitor from the list of monitor models on the screen, and click "Next". 10. Click "Close" → "Close" → "OK" → "OK" on the following screens displayed in sequence.
Using the Software 1. Insert CD into the CD-ROM drive. 2. Click "Start" → "Control Panel" then click the "Appearance and Themes" icon. 3. Click "Display" icon and choose the "Settings" tab then click "Advanced...". 4. Click the "Properties" button on the "Monitor" tab and select "Driver" tab. 5. Click "Update Driver..." and select "Install from a list or..." then click "Next" button. 6. Select "Don't search, I will..." then click "Next" and then click "Have disk".
Using the Software 7. Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next" button. 8. If you can see following message window, then click the "Continue Anyway" button. Then click "OK" button. Note This monitor driver is under certifying MS logo, and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage. http://www.samsung.com/ 9.
Using the Software 10. Monitor driver installation is completed. Microsoft® Windows® 2000 Operating System When you can see "Digital Signature Not Found" on your monitor, follow these steps. 1. Choose "OK" button on the "Insert disk" window. 2. Click the "Browse" button on the "File Needed" window. 3. Choose A:(D:\Driver) then click the "Open" button and then click "OK" button. How to install 1. Click "Start", "Setting", "Control Panel". 2. Double click the "Display" icon. 3.
Using the Software 4. Select the "Monitor" tab. 5. Click the "Change" button in the "Monitor Type" area. 6. Choose "Specify the location of the driver". 7. Choose "Display a list of all the driver in a specific location..." then click "Next" button. 8. Click the "Have Disk" button. 9. Specify A:\(D:\driver) then click "OK" button. 10. Select "Show all devices" and choose the monitor that corresponds to the one you connected to your computer and click "OK". 11.
Using the Software 10. You have finished setting up your monitor. Execute X-Window after setting other requested hardware.
Adjusting the Monitor Direct Functions Note • The monitor LED displays for 10 seconds • Press the MENU button four times continuously to exit OSD AUTO(Available in Analog mode only) When no OSD is displayed,press” ” button to perform the AUTO function, the auto adjustment screen appears as shown in the animated screen on the center. Auto adjustment allows the monitor to self-adjust to the incoming Analog signal.
Adjusting the Monitor Language Exit Brightness (Not available in MagicBright mode of Dynamic Contrast.) You can use the on-screen menus to change the brightness according to personal preference. MENU → MENU → MENU , → MagicBright MagicBright is a new feature providing optimum viewing environment depending on the contents of the image you are watching. Currently five different modes are available: Custom, NotePC, Internet, Movie and Dynamic Contrast.
Adjusting the Monitor For watching motion pictures such as a DVD or Video CD. • Dynamic Contrast Dynamic Contrast automatically detects distribution of inputted visual signal and adjusts to create optimum contrast. Source Choose the video signal between Analog and USB. MENU → , → MENU → MENU→ , Image Size You can change the size of the screen displayed on your monitor. Note • Signals not available in the standard mode table are not supported.
Adjusting the Monitor Note The language chosen affects only the language of the OSD. It has no effect on any software running on the computer. MENU → , → MENU → MENU→ MENU → → MENU Exit Perform this function to close OSD.
Troubleshooting Self-Test Feature Check Note Your monitor provides a self test feature that allows you to check whether your monitor is functioning properly. Self-Test Feature Check 1. Turn off both your computer and the monitor. 2. Unplug the video cable from the back of the computer. 3. Turn on the monitor. If the monitor is functioning properly, you will see a box in the illustration below. This box appears during normal operation if the video cable becomes disconnected or damaged. 4.
Troubleshooting Useful Tips A monitor recreates visual signals received from the computer. Therefore, if there is a problem with the computer or the video card, this can cause the monitor to become blank, have poor coloring, become noisy, and video mode not supported, etc. In this case, first check the source of the problem, and then contact the Service Center or your dealer.
Troubleshooting Mode 1360 x 768(1920 x 1080) 60 Hz" message appears for one minute and then disappears. Please change to the recommended mode during this one-minute period. (The message is displayed again if the system is rebooted.) Q: There is no image on the screen. Is the power indicator on the monitor blinking at 1 second intervals? A: The monitor is in PowerSaver mode. A: Press a key on the keyboard to activate the monitor and restore the image on the screen.
Troubleshooting (The maximum frequency per resolution may differ from product to product.) There are only 16 colors shown on the screen. The screen colors have changed after changing the video card. Q: Have the Windows colors been set properly? A: Windows XP : Set the resolution at the Control Panel → Appearance and Themes → Display → Settings. A: Windows ME/2000 : Set the resolution at the Control Panel → Display → Settings.
Troubleshooting A: The frequency can be changed by reconfiguring the video card. A: Note that video card support can vary, depending on the version of the driver used. (Refer to the computer or the video card manual for details.) Q: How can I adjusts the resolution? A: Windows XP: Set the resolution in the Control Panel → Appearance and Themes → Display → Settings. A: Windows ME/2000: Set the resolution in the Control Panel → Display → Settings. * Contact the video card manufacturer for details.
Specifications General General Model Name SyncMaster LD190 LCD Panel Size 18.5 inch (47 cm) Display area 409.8 mm (H) x 230.4 mm (V) Pixel Pitch 0.3 mm (H) x 0.3 mm (V) Synchronization Horizontal 30 ~ 81 kHz Vertical 50 ~ 75 Hz Display Color 16.7 M Resolution Optimum resolution 1360 x 768@60 Hz Maximum resolution 1360 x 768@60 Hz Input Signal, Terminated RGB Analog, USB 0.7 Vp-p ± 5 % Separate H/V sync, Composite, SOG TTL level (V high ≥ 2.0 V, V low ≤ 0.
Specifications Environmental considerations Humidity : 5 % ~ 95 %, non-condensing Plug and Play Capability This monitor can be installed on any Plug & Play compatible system. The interaction of the monitor and the computer systems will provide the best operating conditions and monitor settings. In most cases, the monitor installation will proceed automatically, unless the user wishes to select alternate settings.
Specifications Preset Timing Modes If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjusts the screen as follows. Display Mode Horizontal Frequency (kHz) Vertical Fre- Pixel Clock quency (Hz) (MHz) Sync Polarity (H/V) IBM, 640 x 350 31.469 70.086 25.175 +/- IBM, 640 x 480 31.469 59.940 25.
Specifications Synchronization Horizontal 30 ~ 81 kHz Vertical 50 ~ 75 Hz Display Color 16.7 M Resolution Optimum resolution 1360 x 768@60 Hz Maximum resolution 1360 x 768@60 Hz Input Signal, Terminated RGB Analog, USB 0.7 Vp-p ± 5 % Separate H/V sync, Composite, SOG TTL level (V high ≥ 2.0 V, V low ≤ 0.
Specifications Dot Acceptable black pixels may be seen. This is not from bad quality and you can use it without any problems. For example, the number of TFT-LCD sub pixels contained in this product are 3,133,440. Note Design and specifications are subject to change without prior notice.
Specifications Display Mode Horizontal Frequency (kHz) Vertical Fre- Pixel Clock quency (Hz) (MHz) Sync Polarity (H/V) IBM, 720 x 400 31.469 70.087 28.322 -/+ MAC, 640 x 480 35.000 66.667 30.240 -/- MAC, 832 x 624 49.726 74.551 57.284 -/- VESA, 640 x 480 37.861 72.809 31.500 -/- VESA, 640 x 480 37.500 75.000 31.500 -/- VESA, 800 x 600 35.156 56.250 36.000 +/+ VESA, 800 x 600 37.879 60.317 40.000 +/+ VESA, 800 x 600 48.077 72.188 50.000 +/+ VESA, 800 x 600 46.
Specifications Resolution Optimum resolution 1920 x 1080@60 Hz Maximum resolution 1920 x 1080@60 Hz Input Signal, Terminated RGB Analog, USB 0.7 Vp-p ± 5 % Separate H/V sync, Composite, SOG TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V) Maximum Pixel Clock 164 MHz (Analog, USB) Power Supply AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz Signal Cable 15pin - to - 15pin D-sub cable, Detachable USB Interface connector,Detachable Dimensions (W x H x D) / Weight (Simple Stand) 594.0 x 405.0 x 123.0 mm (23.4 x 15.
Specifications Class B Equipment (Information Communication equipment for residential use) This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.) PowerSaver This monitor has a built-in power management system called PowerSaver.
Specifications Display Mode Horizontal Frequency (kHz) VESA, 1920 X 1080 66.587 Vertical Fre- Pixel Clock quency (Hz) (MHz) 59.934 138.500 Sync Polarity (H/V) +/- Horizontal Frequency The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle and the inverse number of the Horizontal Cycle is called the Horizontal Frequency.
Specifications Power Supply AC 100 - 240 V~ (+/- 10 %), 50/60 Hz ± 3 Hz Signal Cable 15pin - to - 15pin D-sub cable, Detachable USB Interface connector,Detachable Dimensions (W x H x D) / Weight (Simple Stand) 594.0 x 405.0 x 123.0 mm (23.4 x 15.9 x 4.8 inch) (With Stand) / 5.7 kg(12.
Specifications State Normal Operation Power saving mode Power off (Power button) EPA/ENERGY 2000 Power Indicator On Blinking Off Power Consumption 40 watts Analog: Less than 1.2 watt Less than 1.2 watts USB: Less than 1.2 watt This monitor is EPA ENERGY STAR® compliant and ENERGY 2000 compliant when used with a computer equipped with VESA DPM functionality. As an ENERGY STAR® Partner, SAMSUNG has determined that this product meets the ENERGY STAR® guidelines for energy efficiency.
Information For Better Display Adjust the computer resolution and screen injection rate (refresh rate) on the computer as described below to enjoy the best picture quality. You can have an uneven picture quality on screen if the best picture quality is not provided for TFTLCD. • Resolution: 1360 x 768(1920 x 1080) • Vertical frequency (refresh rate): 60 Hz TFT-LCD panels manufactured by using advanced semiconductor technology with a precision of 1ppm (one millionth) and above is used for this product.
Information the previous image is retained when switching to a new video image. All display products, including LCD, are subject to image retention. This is not a product defect. Please follow the suggestions below to protect your LCD from image retention. Power Off, Screen Saver, or Power Save Mode Ex) • • Turn the power off when using a stationary pattern.
Information • Change the characters color and background color every 30 minutes Ex) • Every 30 minutes, change the characters with movement. Ex) The best way to protect your monitor from Image retention is to set your PC or System to operate a Screen Saver program when you are not using it. Image retention may not occur when a LCD panel is operated under normal conditions. Normal conditions are defined as continuously changing video patterns.
Information Our LCD Monitor satisfies ISO13406-2 Pixel fault Class II
Appendix Contact SAMSUNG WORLDWIDE Note If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center. North America U.S.A 1-800-SAMSUNG(726-7864) http://www.samsung.com/us CANADA 1-800-SAMSUNG(726-7864) http://www.samsung.com/ca MEXICO 01-800-SAMSUNG (726-7864) http://www.samsung.com/mx Latin America ARGENTINA 0800-333-3733 http://www.samsung.com/ar BRAZIL 0800-124-421 http://www.samsung.
Appendix Europe BELGIUM 02 201 2418 http://www.samsung.com/be (Dutch) http://www.samsung.com/ be_fr (French) CZECH REPUBLIC 800 (800-726786) SAMSUNG http://www.samsung.com/cz DENMARK 8 - SAMSUNG (7267864) http://www.samsung.com/dk EIRE 0818 717 100 http://www.samsung.com/ie FINLAND 30 - 6227 515 http://www.samsung.com/fi FRANCE 3260 dites ' SAMSUNG '(€ http://www.samsung.com/fr 0,15/Min) 0825 08 65 65 (€ 0.15/Min) GERMANY 01805 SAMSUNG http://www.samsung.de (7267864, € 0.
Appendix CIS TADJIKISTAN 8-10-800-500-55-500 UKRAINE 8-800-502-0000 http://www.samsung.ua UZBEKISTAN 8-10-800-500-55-500 http://www.samsung.com/ kz_ru Asia Pacific AUSTRALIA 1300 362 603 http://www.samsung.com/au CHINA 800-810-5858 http://www.samsung.com/cn 400-810-5858 010-6475 1880 INDIA HONG KONG:3698 - 4698 http://www.samsung.com/hk 3030 8282 http://www.samsung.com/in 1800 110011 1-800-3000-8282 INDONESIA 0800-112-8888 http://www.samsung.com/id JAPAN 0120-327-527 http://www.
Appendix Vertical Frequency The screen must be redrawn several times per second in order to create and display an image for the user. The frequency of this repetition per second is called the Vertical Frequency or Refresh Rate. Unit: Hz Example: If the same light repeats itself 60 times per second, this is regarded as 60 Hz. Horizontal Frequency The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle.
Appendix Correct Disposal of This Product (Waste Electrical & Electronic Equipment) Business users should contact their supplier and check the terms and conditions of the purchase contract. This product and its electronic accessories should not be mixed with other commercial wastes for disposal. Authority Information in this document is subject to change without notice. © 2009 Samsung Electronics Co., Ltd. All rights reserved.
