SyncMaster 2263DX LCD Monitor User Manual
Safety Instructions Notational Note Please read the following safety instructions as they are designed to prevent damage to property and harm to the user. Warning / Caution Failure to follow directions noted by this symbol could result in bodily harm or damage to the equipment.
Safety Instructions Do not forcefully bend or pull the power plug and do not place any heavy material on it. • Otherwise, this may result in fire. Do not connect multiple appliances to the same power outlet. • Otherwise, this may cause fire due to overheating. Do not disconnect the power cord while using the product. • Otherwise, this may result in damage to the product due to electric shock.
Safety Instructions Keep heating appliances as far away from the power cord or the product as possible. • Otherwise, this may result in electric shock or fire. Do not install it in a badly ventilated location such as a bookcase or closet. • Otherwise, this may result in fire due to an increase in the internal temperature. Put down the monitor carefully. • Failing to do so may damage the monitor. Do not place the front of the product on the floor.
Safety Instructions When cleaning the power plug pins or dusting the power outlet, clean it with a dry cloth. • Otherwise, it may result in fire. When cleaning the product, make sure to disconnect the power cord. • Otherwise, it may result in electric shock or fire. When cleaning the product, disconnect the power cord and clean it softly with a dry cloth. • (Do not use chemicals such as wax, benzene, alcohol, thinner, mosquito repellant, lubricant, or cleaner.
Safety Instructions Do not try to move the monitor by pulling only the wire or the signal cable. • Otherwise, it may fall and result in electric shock, damage to the product or fire due to damage to the cable. Do not lift or move the product back and forwards or right and left while only holding the power cord or signal cables. • Otherwise, it may fall and result in electric shock, damage to the product or fire due to damage to the cable.
Safety Instructions Do not install it in an unstable location such as an unstable rack or uneven surface or a location exposed to vibrations. • Otherwise, it may fall and cause personal injury and/or damage the product. • If you use the product in a location exposed to vibrations, it may damage the product and result in fire. When moving the product, turn the power off and disconnect the power plug, antenna cable, and all the cables connected to the product.
Safety Instructions If the product has been turned on for a long time, the display panel becomes hot. Do not touch it. • Keep the small accessories in a location out of the reach of children. Be careful when adjusting the angle of the product or the height of the stand. • This may result in personal injury as your hand or fingers may become caught. • Also, if you tilt the product too far, it may fall and cause personal injury. Do not install the product in a location low enough for children to reach.
Introduction Package Contents Note Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Contact a local dealer to buy optional items.
Introduction Others Cleaning Cloth Note This is only provided for highly polished black products as a product feature. Your Monitor Initial Settings Select the language using the up or down key. The displayed content will disappear after 40 seconds. Turn the Power button off and on. It will be displayed again. It can be displayed up to three (3) times. Make sure to adjust the resolution of your PC before reaching the maximum count.
Introduction MENU button [MENU/ ] Opens the on-screen menu and exits from the menu. Also use to exit the OSD menu or return to the previous menu. Customized Key You can customize key assignment for the Custom button according to your preferences. Note You can configure the Customized key for a required function via Setup > Customized Key. Volume button When OSD is not on the screen, push the button to adjust volume. >> Click here to see an animation clip Adjust buttons [ ] Adjust items in the menu.
Introduction - You can only hear sound from this monitor model if it is connected to a PC via a USB cable. Use this button to decrease the screen brightness for the 7" USB monitor. The LED blinks when the screen brightness is decreased to the minimum or when a screen brightness adjustment is completed. Use this button to increase the screen brightness for the 7" USB monitor. The LED blinks when the screen brightness is increased to the maximum or when a screen brightness adjustment is completed.
Introduction POWER POWER Connect the power cord for your monitor to the POWER port on the back of the monitor. HDMI / DVI IN / RGB IN HDMI Connect the HDMI terminal at the back of your monitor to the HDMI terminal of your digital output device using a HDMI cable. DVI IN Connect the DVI cable to the DVI IN port on the back of your monitor. RGB IN Connect the RGB IN terminal at the back of your monitor to your computer.
Introduction UP (USB upstream port) Connect the UP port of the monitor and the USB port of the computer with the USB cable. DOWN (USB downstream port) DOWN port of the USB monitor Connect the and a USB device with the USB cable. Note To use DOWN (Downstream Port), you have to connect the PC. UP (Upstream Cable ) to the Make sure to use the USB cable supplied with this monitor to connect the monitor's and your computer's USB port.
Introduction Headphone output terminal MIC Connect a microphone to the MIC terminal. Cable holding ring Fix the cables using the holding ring, as shown in the figure. Note See Connecting Cables for further information regarding cable connections.
Connections Connecting Cables Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. Use a connection appropriate for your computer. Using the D-sub (Analog) connector on the video card. • Connect the signal cable to the 15-pin, D-sub port on the back of your monitor. [RGB IN] Using the DVI (Digital) connector on the video card. • Connect the DVI Cable to the DVI IN Port on the back of your Monitor.
Connections Connecting Using a HDMI Cable 1. Input devices such as digital DVD are connected to the HDMI terminal of the monitor using the HDMI cable. When all the connections are completed, connect the power cords for the monitor and DVD (or the device connected to the digital output terminal). Select HDMI using the SOURCE button. Connecting Using a DVI to HDMI Cable 1. Connect the DVI output terminal of a digital output device to the HDMI terminal of the monitor using a DVI to HDMI cable. 2.
Connections Note If you just connect using the DVI to HDMI cable without connecting to the sound source, you cannot hear sound. Connecting USB Note You can use a USB device such as a mouse, keyboard, Memory Stick, or external hard disk drive by DOWN port of the monitor without connecting them to the PC. connecting them to the The USB port of the monitor supports High-Speed Certified USB 2.0. Data Rate High speed Full speed Low speed 480 Mbps 12 Mbps 1.5 Mbps 2.5 W 2.5 W (Max.
Connections • You can play a file from a media device. (Examples of media devices: MP3, digital camera, etc.) • You can run, move, copy or delete the files on the storage device. (Examples of storage devices: external memory, memory card, memory reader, HDD-type MP3 player, etc.) • You can use other USB devices that can be connected to a computer. Note When connecting a device to the cable appropriate to the device.
Connections Note For more information on the driver installation and usage of the USB monitor, refer to Restrictions on the 7”USB Monitor . Installing and Using the USB Monitor 1. Engage and fix the USB monitor into the groove of the armrest holder. 2. You can adjust the location of the USB monitor. Note You can also adjust the length of the armrest holder after adjusting the location of the USB monitor. 1.
Connections 3. Make sure to use the 7” USB monitor after properly adjusting the angle of its stand. This may cause the center of gravity of the product to change, leading causing the product to fall resulting in damage or a malfunction. 4. When moving a 7” USB monitor, take care not to knock the monitor against something. The monitor may become scratched. 5. When disassembling the 7” USB monitor, remove it by holding the direction of the arrow.
Connections 1. Connect your headphones to the Headphone connection terminal. Connecting MIC Note You may connect your microphone to the monitor. 1. Connect the microphone cable to the MIC port on the monitor.
Connections Swivel stand Using ( ), You can swivel the monitor left and right at an angle of 350° to set the monitor lengthwise. The rubber under the stand is to avoid the monitor slide. When you try to rotate the monitor in the state of the power cord or cable connecting to the monitor, the power cord of cable can be destroyed. Tilt angle Using ( ), You can adjust the tilt angle within a range of -5° forward to 12° backward for the most comfortable viewing angle.
Connections Monitor Mounting interface pad (Sold separately) 1. Turn off your monitor and unplug its power cord. 2. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen. 3. Remove four screws and then remove the stand from the LCD monitor. 4. Turn the armrest holder upwards or downwards. Remove the screws on the armrest holder and remove it. 5.
Using the Software Using the WebCam Monitor This monitor can be used as a normal monitor for video communications and for viewing multimedia files simply by connecting the power cable and the USB cable to your PC. Minimum baseline spec • System Requirements CPU : 1.73GHz or Later OS : Windows XP Service Pack2 or later. However, Windows Vista 64bit is not supported. RAM : 512 MB RAM or more USB : 1.1 or higher (USB 2.0 recommended) Auto Setup for the web camera, microphone and speaker 1.
Using the Software 2. The web camera, microphone and speaker will be set up automatically and appear on the status bar. Note • If the camera is recognized as a USB1.1 device, the screen quality may be degraded and noise may occur. Make sure to upgrade to USB 2.0. • Because of the characteristics of USB communication, the device is recognized whenever it is turned off and on. When the recognition process is finished, you can use it normally.
Using the Software If the installation fails Note If the installation is stopped because the New Hardware Wizard has failed, right-click ”My computer“, and click “Properties” - “System Properties” - the ”Hardware“ tab. Click on the ”Device Manager“ and reinstall the driver by following these steps below. 1. The symbol showing that the device has failed to be installed is displayed as shown in ( , ) 2. In this case, click ”Scan for hardware changes” to run the Setup Wizard again.
Using the Software 2. Click on “Device Manager”. 3. A list of installed devices will be displayed, as shown in the figure below. Checking the Web Camera Setup 1. Double-click My Computer on the Windows Desktop. 2. Double-click the USB Video Device #2. You should find that the web camera has been set up normally, as shown in the figure below. Checking the Microphone and Speaker Setup 1. Double-click Sounds and Audio Devices in the Control Panel.
Using the Software 2. Select the Voice tab and click on Test Hardware. Note If the sound from your monitor is too soft, adjust the volume after setting the volume of your PC to the maximum. 3. Follow the steps described below. You should find that the microphone and speaker have been set up. Restrictions on Using the Monitor 1. The Camera and Audio functions of this monitor except the basic Display function are recognized as USB Devices.
Using the Software Note This monitor must be connected with a D-Sub (Analog) or a DVI-D cable (Digital) when used as a normal monitor. USB cables are used when connecting other devices. 2. For some media players, when a USB device is being recognized again while a media player is running, you have to close and run it again to operate the sound and camera devices normally. 3.
Using the Software Webcam 1. Insert the Program Setup CD into the CD-ROM drive. 2. Click on Web Cam Companion 2 (WCC2). 3. Select a language and click the "OK" button. 4. Click the "Next" button. 5. Click the "Yes" button. 6. Click the "Next" button.
Using the Software 7. Click the "Next" button. 8. Click the “Finish” button. The installation of the Web Cam Companion 2 is completed. Note For more information on how to use the program, refer to its “Help” section. Opening the chat program • When the installation of the Web Cam Companion 2 program is completed, touch the “ ” position on the monitor for the Web Cam Companion 2 chat window to appear, as shown in the figure below.
Using the Software • • • Install or select the chat program you want to use. Touch the “ mediately. ” position on the monitor. The chat window of the selected program appears im- To change the chat program to which a shortcut was created, select the Utility in the Start -> All Programs -> Arcsoft Web Cam Companion 2 . Magic-I Visual Effects ArcSoft Magic-i™! Visual Effects is a smart and simple webcam application designed to enhance users' video chat experience through frames, effects, and themes.
Using the Software DirectX 9.0c or above 1. Insert the Program Setup CD into the CD-ROM drive. 2. Click on Magic-I Visual Effects. 3. Select a language and click the "OK" button. 4. Click the "Next" button. 5. Click the "Yes" button. 6. Click the "Next" button.
Using the Software 7. Click the "Next" button. 8. Click the “Finish” button. The installation of the Magic-I Visual Effects is completed. Note For more information on how to use the program, refer to its “Help” section. Media-Impression ArcSoft Media Impression™ manages your media for you, and gives you tons of fun and exciting ways to create and share projects featuring your photo, video, and music files.
Using the Software Pentium III 1 GHz or equivalent 512 MB RAM 150 MB available hard disk space 800x600 pixels, 16-bit color monitor Microsoft Windows Media Player 9.0 or higher Microsoft DirectX 9.0 or higher Apple QuickTime® 7.0 or higher recommended - Macintosh OS X 10.3, 10.4 PowerPC G4 800 MHz, or Intel processor 150 MB available hard disk space 800x600 pixels, 16-bit color monitor Apple QuickTime®6.0 or higher 1. Insert the Program Setup CD into the CD-ROM drive. 2. Click on Media-Impression. 3.
Using the Software 6. Click the "Next" button. 7. Click the "Next" button. 8. Select a file type and click the “Next” button.
Using the Software 9. Click the "Finish" button. The installation of the Media-Impression is completed. Note For more information on how to use the program, refer to its “Help” section. Installing the 7” USB Monitor Driver • System Requirements CPU : 1.73GHz or Later OS : Windows XP Service Pack2 or later. However, Windows Vista 64bit is not supported. RAM : 512 MB RAM or more USB : 1.1 or higher (USB 2.
Using the Software • The optimal resolution for this USB monitor is 800x480. 1. Insert CD into the CD-ROM drive. Click "USB Monitor Driver" 2. Click "I Accept". 3. The progress window appears, as shown in the figure below. 4. If you connect your USB monitor to your PC, it recognizes the monitor and the "Found New Hardware" wizard is displayed, as shown in the figure below.
Using the Software 3. Arrange the monitors displayed in the 'Display Properties' window in the order they are actually used. 4. Then click "OK" button. Configuring the 7" USB Monitor Display Information 1. When the driver setup for the USB monitor is finished, a monitor icon is created in the system tray at the bottom of the monitor screen. 2. Click the monitor icon to display a list of connected USB monitors. Select the monitor for which you want to configure the display settings.
Using the Software Checking the configuration After the installation, you can check the configuration by following these steps. 1. Right-click “My Computer”, and select “Properties” - “System Properties” - the “Hardware tab”. 2. Click “Device Manager”. 3. A list of the installed device will be displayed, as shown in the figure below.
Using the Software - The Initial Screen Settings after Installing the Program • Applicable mode: Extend mode • Mode position: To the right of the primary screen • Mode rotation: 0° Restrictions on the 7” USB Monitor Supported OS (Operating Systems) • Windows XP - Service Pack 1 or earlier: Unsupported - Service Pack 2 or later: Supported • Windows 2000 - Service Pack 3 or earlier: Not Supported - Service Pack 4 or later: Supported • Windows Server 2003: Not Supported • Windows Vista: Supported
Using the Software - Power DVD - Win DVD(Version 5 onwards) - Windows Media Player (Version 10 or later is supported.) - VLC 4. This monitor does not support the MagicTune program. - The MagicRotation function may not function normally. - If the MagicTune program is installed on your PC, it may not be compatible with this monitor. 5. The USB monitor may not work normally with USB 1.0. 6. If the graphics card of your PC does not support WDDM, the extended mode may not be available in Windows Vista.
Using the Software 4. If you can see following message window, then click the "Continue Anyway" button. Then click "OK" button (Microsoft® Windows® XP/2000 Operating System). Note This monitor driver is under certifying MS logo, and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage. http://www.samsung.com/ Installing the Monitor Driver (Manual) Microsoft® Windows Vista™‚ Operating System 1. Insert your Manual CD into your CD-ROM drive. 2.
Using the Software 5. Click "Properties" in the "Monitor" tab. If the "Properties" button is deactivated, it means the configuration for your monitor is completed. The monitor can be used as is. If the message "Windows needs..." is displayed, as shown in the figure below, click "Continue". Note This monitor driver is under certifying MS logo, and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage. 6. Click "Update Driver..." in the "Driver" tab.
Using the Software 8. Click "Have Disk...” and select the folder (for example, D:\Drive) where the driver setup file is located, and click "OK". 9. Select the model that matches your monitor from the list of monitor models on the screen, and click "Next". 10. Click "Close" → "Close" → "OK" → "OK" on the following screens displayed in sequence.
Using the Software Microsoft® Windows® XP Operating System 1. Insert CD into the CD-ROM drive. 2. Click "Start" → "Control Panel" then click the "Appearance and Themes" icon. 3. Click "Display" icon and choose the "Settings" tab then click "Advanced...". 4. Click the "Properties" button on the "Monitor" tab and select "Driver" tab.
Using the Software 5. Click "Update Driver..." and select "Install from a list or..." then click "Next" button. 6. Select "Don't search, I will..." then click "Next" and then click "Have disk". 7. Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next" button. 8. If you can see following message window, then click the "Continue Anyway" button. Then click "OK" button.
Using the Software http://www.samsung.com/ 9. Click the "Close" button then click "OK" button continually. 10. Monitor driver installation is completed. Microsoft® Windows® 2000 Operating System When you can see "Digital Signature Not Found" on your monitor, follow these steps. 1. Choose "OK" button on the "Insert disk" window. 2. Click the "Browse" button on the "File Needed" window. 3. Choose A:(D:\Driver) then click the "Open" button and then click "OK" button. How to install 1.
Using the Software 9. Choose your monitor model and click the "Next" button then click "Next" button. 10. Click the "Finish" button then the "Close" button. If you can see the "Digital Signature Not Found" window then click the "Yes" button. And click the "Finish" button then the "Close" button. Microsoft® Windows® Millennium Operating System 1. Click "Start", "Setting", "Control Panel". 2. Double click the "Display" icon. 3. Select the "Settings" tab and click "Advanced Properties" button. 4.
Using the Software 5. Set a Keyboard for your computer. 6. The next screen is for setting your monitor. 7. First of all, set a horizontal frequency for your monitor. (You can enter the frequency directly.) 8. Set a vertical frequency for your monitor. (You can enter the frequency directly.) 9. Enter the model name of your monitor. This information will not affect the actual execution of X-Window. 10. You have finished setting up your monitor.
Using the Software How to delete the Natural Color software program Select "Setting/Control Panel" on the "Start" menu and then double-click "Add/Delete a program". Select Natural Color from the list and then click the "Add/Delete" button.
Adjusting the Monitor Direct Functions AUTO When the 'AUTO' button is pressed, the auto adjustment screen appears as shown in the animated screen on the center. Auto adjustment allows the monitor to self-adjust to the incoming Analog signal. The values of Fine, Coarse and Position are adjusted automatically. (Available in Analog mode only) If auto adjustment does not work properly, press 'AUTO' button again to adjust picture with more accuracy.
Adjusting the Monitor When pressing the MENU button after locking the OSD This is the function that locks the OSD in order to keep the current states of settings or prevent others from adjusting the current settings. Lock : Hold down the MENU button for more than five (5) seconds to activate the OSD adjustment lock function. Unlock : Hold down the MENU button for more than five (5) seconds to deactivate the OSD adjustment lock function.
Adjusting the Monitor Note Though the OSD adjustment lock function is activated, you can still adjust the brightness and contrast, and adjust Customized Key ( ) using the Direct button. Customized key You can customize key assignment for the Custom button according to your preferences. To view the operating screen displayed when pressing the [ tomized key for a function, click the name of each function.
Adjusting the Monitor Volume When OSD is not on the screen, push the button to adjust volume. SOURCE Selects the video signal while the OSD is off.
Adjusting the Monitor Color MagicColor Color Tone Color trol Con- Color Effect Gamma Image Coarse Fine Sharpness H-Position OSD Language H-Position V-Position Transparen- Display Time cy Setup Reset Customized Off Timer Key AV Mode HDMI Black Level V-Position Auto Source Image Size Information Picture Brightness (Not available in MagicBright mode of Dynamic Contrast.) You can use the on-screen menus to change the brightness according to personal preference.
Adjusting the Monitor You can use the on-screen menus to change the contrast according to personal preference. ( Not available in MagicColor mode of Full and Intelligent. ) MENU → → , → → , → MENU MagicBright Push the button to circle through available preconfigured modes. MagicBright is a new feature providing optimum viewing environment depending on the contents of the image you are watching.
Adjusting the Monitor Game, Sport, Movie and Dynamic Contrast. Each mode has its own pre-configured brightness value. You can easily select one of seven settings by simply pressing Customized Key control button. • Custom Although the values are carefully chosen by our engineers, the pre-configured values may not be comfortable to your eyes depending on your taste. If this is the case, adjust the brightness and contrast by using the OSD menu. • Text For documentations or works involving heavy text.
Adjusting the Monitor The Monitor has four automatic picture settings ("Dynamic", "Standard", "Movie" and "Custom") that are preset at the factory. You can activate either Dynamic, Standard, Movie, or Custom. You can select Custom which automatically recalls your personalized picture settings. • Dynamic Select this mode to view a sharper image than in Standard mode. • Standard Select this mode when the surroundings are bright. This also provides a sharp image.
Adjusting the Monitor • Off - Returns to the original mode. • Demo - The screen before applying MagicColor appears on the right and the screen after applying MagicColor appears on the left. • Full - Displays not only vivid natural color but also more realistic natural skin color with clearness. • Intelligent - Displays vivid natural color with clearness. MENU → , → → → , → MENU Color Tone The tone of the color can be changed and one of four modes can be selected.
Adjusting the Monitor Color Control Adjusts individual Red, Green, Blue color balance. ( Not available in MagicColor mode of Full and Intelligent. ) MENU → , → → , → → , → → , → MENU Color Effect You can change the overall mood by changing the screen colors. ( Not available in MagicColor mode of Full and Intelligent.
Adjusting the Monitor • Off - This applies an achromatic color to the screen to adjust the screen effects. • Grayscale - The default colors of black and white are displayed. • Green - This applies the green color effect to a black and white screen. • Aqua - This applies the aqua color effect to a black and white screen. • Sepia - This applies the Sepia color effect to a black and white screen.
Adjusting the Monitor Image Coarse Removes noise such as vertical stripes. Coarse adjustment may move the screen image area. You may relocate it to the center using the horizontal control menu.
Adjusting the Monitor Fine Removes noise such as horizontal stripes. If the noise persists even after Fine tuning, repeat it after adjusting the frequency (clock speed). (Available in Analog mode only) MENU → , → → , → Sharpness Changes the clearance of image.
Adjusting the Monitor ( Not available in MagicColor mode of Full and Intelligent. ) MENU → , → → , → → , → MENU H-Position Changes the horizontal position of the monitor's entire display.
Adjusting the Monitor Changes the vertical position of the monitor's entire display. (Available in Analog mode only) MENU → , → → , → → , → MENU OSD Language You can choose one of nine languages. Note The language chosen affects only the language of the OSD. It has no effect on any software running on the computer.
Adjusting the Monitor H-Position You can change the horizontal position where the OSD menu appears on your monitor. MENU → , → → , → → , → MENU V-Position You can change the vertical position where the OSD menu appears on your monitor.
Adjusting the Monitor Transparency Change the transparency of the background of the OSD. • Off MENU → • , → On → , → → , → MENU Display Time The menu will be automatically turned off if no adjustments are made for a certain time period. You can set the amount of time the menu will wait before it is turned off.
Adjusting the Monitor • 5 sec MENU → • , → 10 sec → , → → • 20 sec , → MENU Setup Reset Reverts the product settings to factory defaults.
Adjusting the Monitor Customized Key You can specify a function which will be activated when the Customized Key ( MENU → , → → , → → , →MENU Off Timer The monitors will turn off automatically at the specified time. • Off • On )is pressed.
Adjusting the Monitor MENU → , → → , → → , → → , → MENU Auto Source Select Auto Source for the monitor to automatically select the signal source.
Adjusting the Monitor You can change the size of the screen displayed on your monitor. • Auto - The screen is displayed in accordance with the screen aspect ratio of the input signals. • Wide - A full screen is displayed regardless of the screen aspect ratio of the input signals. Note • Signals not available in the standard mode table are not supported. • If the wide screen which is the optimal resolution for the monitor is set on your PC, this function is not performed.
Adjusting the Monitor AV Mode This function allows the screen to be displayed at the optimal quality in accordance with the size of the screen when a 480P, 576P, 720P, 1080i, or 1080P video signal is input in HDMI/DVI mode. Set to Off when connected to a PC, Set to On when connected to an AV device. If not set to On, the screen may not be displayed normally.
Adjusting the Monitor HDMI Black Level When a DVD or set-top box is connected to your TV via HDMI, it may cause a degradation in the screen quality, such as an increase in the black level, a low contrast, or discoloration, etc., depending on the external device connected. In this case, adjust the screen quality of your TV by configuring the HDMI black level.
Adjusting the Monitor MENU → , →MENU
Troubleshooting Self-Test Feature Check Note Your monitor provides a self test feature that allows you to check whether your monitor is functioning properly. Self-Test Feature Check 1. Turn off both your computer and the monitor. 2. Unplug the video cable from the back of the computer. 3. Turn on the monitor. If the monitor is functioning properly, you will see a box in the illustration below. This box appears during normal operation if the video cable becomes disconnected or damaged. 4.
Troubleshooting noisy, and video mode not supported, etc. In this case, first check the source of the problem, and then contact the Service Center or your dealer. Judging the monitor's working condition If there is no image on the screen or a "Not Optimum Mode", "Recommended Mode 1680 x 1050 60 Hz" message comes up, disconnect the cable from the computer while the monitor is still powered on.
Troubleshooting A: If the display exceeds WSXGA or 75 Hz, a "Not Optimum Mode", "Recommended Mode 1680 x 1050 60 Hz" message is displayed. If the display exceeds 85 Hz, the display will work properly but the "Not Optimum Mode", "Recommended Mode 1680 x 1050 60 Hz" message appears for one minute and then disappears. Please change to the recommended mode during this one-minute period. (The message is displayed again if the system is rebooted.) Q: There is no image on the screen.
Troubleshooting Q: The screen can be unbalanced due to the cycle of the video card signals. Readjust Position by referring to the OSD. The screen is out of focus or OSD cannot be adjusted. Q: Have you adjusted the resolution or frequency on the monitor? A: Adjust the resolution and frequency of the video card. (Refer to the Preset Timing Modes). LED is blinking but no images on the screen.
Troubleshooting The screen of the USB monitor freezes. Q: Check the “Hardware acceleration” setting for your USB monitor in the “Display Properties” window. A: Set the “Hardware acceleration” value to “Full”. For more information on how to configure the settings, click here. 1. Right-click the “Windows Desktop” and click on “Properties”. 2. The “Display Properties” window appears. Select the “Settings” tab and click on “Advanced”. 3.
Troubleshooting Check if the scanning ratio of the video screen is set to between 56 Hz ~ 75 Hz. (Do not exceed 75 Hz when using the maximum resolution.) If you have problems in installing the adapter (video) driver, boot the computer in Safe Mode, remove the Display Adapter in the "Control Panel → System → Device Administrator" and then reboot the computer to reinstall the adapter (video) driver. Note If problems repeatedly occur, contact an authorized service center.
Troubleshooting A: Click “Add/Remove Programs” in the “Control Panel”. A list of “currently installed programs” is displayed. Select “Samsung UbiSync Monitor” from the list and click “Remove”. Q: The screen size of the USB monitor is larger than the actual monitor size. A: If the primary monitor has a high resolution, screens are expanded beyond the recommended resolution in Clone mode (USB monitor). Q: The screen size of the USB monitor is smaller than the actual monitor size.
Specifications General 22” Monitor General Model Name SyncMaster 2263DX LCD Panel Size 22 " diagonal (55 cm) Display area 473.76 mm(H) x 296.1 mm(V) Pixel Pitch 0.282 mm(H) x 0.282 mm(V) Synchronization Horizontal 30 ~ 81 kHz Vertical 56 ~ 75 Hz Display Color 16.7M Resolution Optimum resolution 1680x1050@60Hz Maximum resolution 1680x1050@60Hz Input Signal, Terminated RGB Analog, DVI(Digital Visual Interface) Compliant Digital RGB 0.
Specifications VESA Mounting Interface 100 mm x 100 mm (For use with Specialty(Arm) Mounting hardware.) Environmental considerations Operating Temperature : 50°F ~ 104°F (10°C ~ 40°C) Humidity : 10 % ~ 80 %, non-condensing Storage Temperature : -4°F ~ 113°F (-20°C ~ 45°C) Humidity : 5 % ~ 95 %, non-condensing Plug and Play Capability This monitor can be installed on any Plug & Play compatible system.
Specifications Resolution Optimum resolution 800x480@60Hz Maximum resolution 800x480@60Hz Input Signal, Terminated USB interface (Compliant Digital RGB) USB Format TTL level (V high ≥ 2.0 V, V low ≤ 0.8 V) Maximum Pixel Clock 30 MHz (USB Mode) Power Supply DC 5V (USB Power) (+/- 10 %) Signal Cable USB Cable (1 up to 2 down), Detachable Dimensions (W x H x D) / Weight (Simple Stand) 184.0 x 124.0 x 43.6 mm / 7.2 x 4.9 x 1.7 inch / 0.37kg / 0.
Specifications Preset Timing Modes If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjusts the screen as follows. 22” Monitor Display Mode Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) IBM, 640 x 350 31.469 70.086 25.175 +/- IBM, 640 x 480 31.
Information For Better Display Adjust the computer resolution and screen injection rate (refresh rate) on the computer as described below to enjoy the best picture quality. You can have an uneven picture quality on screen if the best picture quality is not provided for TFT-LCD.
Information lates between the two electrodes which encase the liquid crystal. This may cause the liquid crystal to build up in a certain areas of the display. Thus, the previous image is retained when switching to a new video image. All display products, including LCD, are subject to image retention. This is not a product defect. Please follow the suggestions below to protect your LCD from image retention.
Information • Change the characters color and background color every 30 minutes Ex) • Every 30 minutes, change the characters with movement. Ex) The best way to protect your monitor from Image retention is to set your PC or System to operate a Screen Saver program when you are not using it. Image retention may not occur when a LCD panel is operated under normal conditions. Normal conditions are defined as continuously changing video patterns.
Information Our LCD Monitor satisfies ISO13406-2 Pixel fault Class II
Appendix Contact SAMSUNG WORLDWIDE Note If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center. North America U.S.A 1-800-SAMSUNG(726-7864) http://www.samsung.com CANADA 1-800-SAMSUNG(726-7864) http://www.samsung.com/ca MEXICO 01-800-SAMSUNG(726-7864) http://www.samsung.com Latin America ARGENTINE 0800-333-3733 http://www.samsung.com/ar BRAZIL 0800-124-421 http://www.samsung.com 4004-0000 CHILE 800-SAMSUNG(726-7864) http://www.
Appendix Europe GERMANY 01805 - SAMSUNG (726-7864) http://www.samsung.com (€ 0,14/Min) HUNGARY 06-80-SAMSUNG (726-7864) http://www.samsung.com ITALIA 800-SAMSUNG (726-7864) http://www.samsung.com LUXEMBURG 0035 (0)2 261 03 710 http://www.samsung.com/be NETHERLANDS 0900 SAMSUNG (726-7864 € http://www.samsung.com/nl 0,10/Min) NORWAY 815-56 480 http://www.samsung.com/no POLAND 0 801 801 881 http://www.samsung.com/pl 022-607-93-33 PORTUGAL 80820-SAMSUNG (726-7864) http://www.samsung.
Appendix Asia Pacific TAIWAN 0800-329-999 http://www.samsung.com/tw VIETNAM 1 800 588 889 http://www.samsung.com Middle East & Africa SOUTH AFRICA 0860-SAMSUNG(726-7864) http://www.samsung.com TURKEY 444 77 11 http://www.samsung.com U.A.E 800-SAMSUNG(726-7864) http://www.samsung.com 8000-4726 Terms Dot Pitch The image on a monitor is composed of red, green and blue dots. The closer the dots, the higher the resolution.
Appendix Correct Disposal Correct Disposal of This Product (Waste Electrical & Electronic Equipment) Europe only (Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life.
