SyncMaster 940MW Install Driver Install Program
Failure to follow directions noted by this symbol could result in bodily harm or damage to the equipment. Prohibited Important to read and understand at all times Do not disassemble Disconnect the plug from the outlet Do not touch Ground to prevent an electric shock Power When not used for extended period of time, set your computer to DPMS. If using a screen saver, set it to active screen mode. Do not use a damaged or loose plug. z This may cause electric shock or fire.
Do not pull the plug out by the wire nor touch the plug with wet hands. z This may cause electric shock or fire. Use only a properly grounded plug and receptacle. z An improper ground may cause electric shock or equipment damage. Insert the power plug firmly so that it does not come loose. z A bad connection may cause fire. Do not excessively bend the plug and wire nor place heavy objects upon them, which could cause damage. z This may cause electric shock or fire.
location with heavy dust, high or low temperatures, high humidity, and exposed to chemical substances and where it operates for 24 hours such as at airports, train stations etc. z Failure to do so may cause serious damage to your monitor. Place your monitor in a location with low humidity and a minimum of dust. z Failure to do so may cause electric shock or fire inside the monitor. Do not drop the monitor when moving it. z This may cause damage to the product or the person carrying it.
z The monitor could be damaged or broken. Do not place the monitor face down. z This may damage the TFT-LCD surface. The installation of the bracket must be done by a qualified professional. z z Installing the bracket by unqualified personnel may result in injury. Always use the mounting device specified in the owner's manual. When installing the product, make sure to keep it away from the wall (more than 10 cm / 4 inches) for ventilation purposes.
z This may cause damage, electric shock or fire. Use the recommended detergent with a smooth cloth. If the connector between the plug and the pin is dusty or dirty, clean it properly using a dry cloth. z A dirty connector may cause electric shock or fire. Make sure to unplug the power cord before cleaning the product. z Otherwise, this may cause electric shock or fire. Unplug the power cord from the power outlet and wipe the product using a soft, dry cloth.
Keep the product away from places exposed to oil, smoke or moisture; do not install inside a vehicle. z z This may cause a malfunction, electric shock or fire. In particular, avoid operating the monitor near water or outdoors where it could be exposed to snow or rain. If the monitor is dropped or the casing is damaged, turn the monitor off and unplug the power cord. Then contact a Service Center . z The monitor may cause a malfunction, electric shock or fire.
Do not insert metal objects such as chopsticks, wire and gimlet or inflammable objects such as paper and match into the vent, headphone port or AV ports or etc. z It may cause a fire or an electric shock. If an alien substances or water flows into the product, turn the product off, unplug the power connector from the wall outlet and contact the Service Center. If you view a fixed screen for an extended period of time, residual image or blurriness may appear.
When not using the product for an extended period of time, keep the product unplugged. z Otherwise, this may cause heat emission from the accumulated dirt or degraded insulation, causing electric shock or fire. Do not place your children's favorite toys or any other objects of interest on the product. z Children may try to climb on the product to retrieve an object. The product could fall, causing causing injury or even fatality.
Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Contact a local dealer to buy optional items.
Cable D-Sub Cable Audio Cable Power Cord Remote Control Batteries (AAA X 2) Connecter DVI Cable RCA Cable (Video-Yellow, Audio-Red and White) Component(PR, PB, Y) Cable S-Video Cable Earphones/Headphones SCART Cable Others Sold separately TV antenna cable
Front 1. SOURCE 2. PIP 3. MENU 4. CH 5. - VOL + ] Power button 8. Power indicator 9. Remote Control Sensor 10. Speaker 6. [ ] Enter button 7. [ 1. SOURCE Press the 'SOURCE' button to change the input signal source. Changing the source is allowed only in external devices that are connected to the monitor at the time. To switch Screen modes: [PC] ˧ [DVI] ˧ [TV] ˧ [Ext.
Rear (The configuration at the back of the monitor may vary from product to product.) 1. POWER Power terminal Connect the power cord for your monitor to the POWER on the back of the monitor. This product may be used with 100 ~ 240VAC(+/- 10%). 2. DVI/PC IN DVI/PC IN 1. DVI(HDCP) : Connect the DVI cable to the DVI(HDCP) port on the back of your monitor. 2. RGB : Connect the signal cable to the RGB port on the back of your monitor. 3. AUDIO : PC sound terminal (input) 3.
4. COMPONENT IN COMPONENT IN 1. R - AUDIO - L : DVD/DTV sound input terminal (left/right) 2. PR, PB,Y : DVD/DTV video input terminal(PR, PB,Y) 5. ANT IN ANT IN Connect the CATV cable or TV antenna cable to the "ANT IN" port on the rear side of the monitor. Make sure to use a TV antenna cable (sold separately) as the antenna cable. 6. / S-VIDEO / VIDEO / L - AUDIO - R 1. : Headphone sound output terminal 2. S-VIDEO : External device (S-video) input terminal 3.
See Connecting the monitor for further information regarding cable connections. Remote Control The performance of the remote control may be affected by a TV or other electronic device operated near the monitor, causing malfunction due to interference with frequency. 1. POWER 2. Number button 3. +100, -/-- 4. - + 5. MUTE 6. TTX/MIX 7. MENU 8. ENTER 9. CH/P 10. SOURCE 11. INFO 12. EXIT 13. Up-Down Left-Right buttons 14. AUTO 15. P.MODE, M/B (MagicBright™) 16. P.SIZE 17. STILL 18.
2. Number button Selects TV channels in the TV mode. Used to change channels when PIP is selected and the PIP Source is set to TV. 3. +100 Press to select channels over 100. For example, to select channel 121, press "+100", then press "2" and "1". -/-- (One/Two-Digit channel selection ) Use to select a channel numbered ten or over. Press this button, and the "--" symbol is displayed. Enter the two-digit channel number. This function is available only in Europe. 4. + Adjusts the audio volume. 5.
. STILL - Operates only for the CVBS, S-Video and RF Signal sources. Press the button once to freeze the screen. Press it again to unfreeze. 18. PIP - Available in PC/DVI Mode Push the PIP button to turn PIP screen On/Off. 19. S.MODE ( Sound Mode ) When you press this button, current mode is displayed on the lower center of the screen. The monitor has a built-in high fidelity stereo amplifier. Then push button again to circle through available preconfigured modes.
Connecting the monitor 1.Connecting to a Computer 1. Connect the power cord for your monitor to the POWER on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. 2-1. Using the D-sub (Analog) connector on the video card. Connect the signal cable to the RGB port on the back of your monitor. 2-2. Using the DVI (Digital) connector on the video card. Connect the DVI cable to the DVI(HDCP) port on the back of your monitor. 3.
1. Using the D-sub (Analog) connector on the video card. Connect the signal cable to the D-SUB port on the Macintosh computer. 2. For older model Macintoshes, you need to adjust the resolution control DIP switch on the Macintosh adapter (optional) referring to the switch configuration table shown on its rear. 3. Turn on the monitor and Macintosh.
3. Then, start the DVD, VCR or Camcorders with a DVD disc or tape inserted. 4. Select AV or S-Video using the SOURCE. 1-2. Connecting EXT.(RGB) - It only applies to AV DEVICE that supports SCART. Connect to the DVD Devices input if the device has a EXT (RGB) jack. You can watch DVD simply by hooking up the DVD player with the monitor as long as the power is on. 1. Connect the EXT (RGB) port of the monitor to the DVD Player using a SCART jack. 2. Select Ext. by using the SOURCE. 2.
Is weak signal causing poor reception? Purchase and install a signal amplifier for better reception. In areas where Antenna cable is not supported, first, attach Connecter to TV antenna . 3. Connecting DVD/DTV Set Top Box Connect to the DVD/DTVSet Top Box input if the device has a DVD/DTV connector. You can watch Component simply by hooking up the Component with the monitor as long as the power is on. 1. Connect the port of the DVD, VCR (DVD / DTV Set-Top Box) to the R-AUDIO-L port of the monitor. 2.
1. Connect your headphones to the Headphone connection terminal. Using the Stand This monitor supports various types of VESA-standard bases. You need to either fold or remove the base in use in order to install a VESA base. 1. Folding the base The monitor may be reclined from -1 to 23 degrees. 2. Attaching a base This monitor accepts a 100 mm X 100 mm VESA-compliant mounting interface pad. A. Monitor B. Mounting interface pad (Sold separately) 1. Turn off your monitor and unplug its power cord. 2.
To mount the monitor on a wall, you should purchase the wall mounting kit that allows you to mount the monitor at least 10cm away from the wall surface. Contact the nearest Samsung Service Center for more information. Samsung Electronics will not be responsible for damages caused by using a base other than those specified. Please use Wall Mount according to the International standards.
Installing the monitor driver (Manual) Windows XP | Windows 2000 |Windows Me |Windows NT | Linux When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions appropriate for the operating system you have. Prepare a blank disk and download the driver program file at the Internet web site shown here. z Internet web site : http://www.samsung.
6. Select "Don't search ,I will.." then click "Next" and then click "Have disk". 7. Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next" button. 8. If you can see following message window, then click the "Continue Anyway" button. Then click "OK" button. This monitor driver is under certified MS logo,and this installation doesn't damage your system.The certified driver will be posted on Samsung Monitor Homepage. http://www.samsung.com/ 9.
10. Monitor driver installation is completed. Microsoft® Windows® 2000 Operating System When you can see "Digital Signature Not Found" on your monitor, follow these steps. 1. Choose "OK" button on the "Insert disk" window. 2. Click the "Browse" button on the "File Needed" window. 3. Choose A:(D:\Driver) then click the "Open" button and then click "OK" button. How to install 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Click "Start" , "Setting" , "Control Panel". Double click the "Display" Icon.
Microsoft® Windows® NT Operating System 1. Click Start, Settings, Control Panel, and then double-click Display icon. 2. In Display Registration Information window, click Settings Tab and then click All Display Modes. 3. Select a mode that you wish to use (Resolution, Number of colors and Vertical frequency) and then click OK. 4. Click Apply button if you see the screen working normally after clicking Test.
Enter D:\color\NCProSetup.exe and then press the key. (If the drive where the CD is inserted is not D:\, enter the applicable drive.) Uninstalling the Natural Color Software Program Select [Settings]/[Control Panel] from the [Start] menu and then double-click [Add/Delete a program]. Select Natural Color from the list and then click the [Add/Delete] button.
Input Available Source List : PC / DVI : TV : Ext. : AV : SVideo : Component OSD Description Source List Use to select PC or other external input sources connected to the Monitor. Use to select the screen of your choice. - The direct button on the remote control is 'SOURCE' button. PC DVI : HDCP supported TV Ext. It is connected to the EXT(RGB) jack of the monitor and the TV or Video signal is input/output through this jack.
- Available in PC, DVI modes. PIP: Turn the PIP Screen on or off. ON/ Off - The direct button on the remote control is 'PIP' button. PIP Source: Select the input source for the PIP. Main Source: PC / DVI PIP Source (Sub): TV / Ext. / AV / S-Video - The direct button on the remote control is 'SOURCE' button. Source Size Size: Changing the Size of the PIP window. / / If you select in Size, Position will not be activated. - The direct button on the remote control is 'SIZE' button.
Currently four different modes are available: Entertain, Internet,Text and Custom. Each mode has its own pre-configured brightness value. You can easily select one of four settings by simply pressing the MagicBright™ control button. - The direct button on the remote control is 'M/B' button. Entertain For watching motion pictures such as a DVD or VCD. Internet For working with a mixture of images such as text and graphics. Text For documentations or works involving heavy text.
: Adjusts the Brightness of the PIP window on the screen. Sharpness : Adjusts the Sharpness of the PIP window on the screen. Colour : Adjusts the Color of the PIP window on the screen. Source List : TV / Ext. / AV / S-Video / Component Available Source List : PC / DVI : TV : Ext. : AV : SVideo : Component OSD Description Mode The monitor has four automatic picture settings ("Dynamic", "Standard", "Movie", and "Custom") that are preset at the factory.
Size You can switch the Size. - The direct button on the remote control is 'P.SIZE' button. Auto Wide / Wide / Zoom / 4:3 Zoom is not available in 1080i(or over 720p) of DTV. Sound Available Source List : PC / DVI : TV : Ext. : AV : SVideo : Component OSD Description Mode The monitor has a built-in high fidelity stereo amplifier. - The direct button on the remote control is 'S.MODE' button. Standard : Choose Standard for the standard factory settings.
right speakers and you can hear the sound even when the sound value is set to 0. Auto Volume Reduces the differences in volume level among broadcasters. On /Off Dolby Virtual Dolby Virtual Sound On/Off (Dolby Virtual simulates the effect of the Dolby Surround sound system, recreating the movie-theatre or concert-hall- quality sound.
Manual Store You can scan the frequency ranges available on your television in your area and store all the channels found manually. Programme: Inputting the appropriate program number on the screen. Colour System: Adjust repeatedly until the color is of the best quality. AUTO, PAL, SECAM, NT4.43 Sound System: Adjust repeatedly until the sound is of the best quality. BG , DK, I, L Channel : Choosing the air channel through the adjustment of up/down under the current frequency.
Area When you turn the power on of the product for the first time since it released Configuration from a factory, menu to select location will appear. Choose the region and country where you use the monitor. This is because broadcasting type varies according to region and country. You can select broadcasting type in OSD menu as well by selecting MENUSetup-Area Configuration. This product can be used worldwide if area configuration is set up regardless of broadcasting type.
Self-Test Feature Check Check the following items yourself before calling for service. Contact the service center for problems that you cannot solve by yourself. Self-Test Feature Check | Not Optimum Mode | Display Adapter Driver Maintenance and Cleaning | Symptoms & Recommended Actions 1. Self-Test Feature Check Your monitor provides a self test feature that allows you to check whether your monitor is functioning properly. 1. Turn off both your computer and the monitor. 2.
supported by the monitor. 3. Display Adapter Driver Display adapter refers to the computer video card driver. If the adapter is not properly set, you cannot adjust resolution, frequency or color and you cannot install the monitor driver. 1. Checking Adapter Driver Click Start Settings Control Panel Display Settings Advanced Adapter. If "Default" or a wrong product model is indicated, it means that the adapter driver is not properly installed.
Installation | Screen | Audio | Remote Control 1. Problems related to Installation Problems related to the monitor installation and their solutions are listed. Problems PC Mode Solutions It appears the PC does not function normally. z The monitor screen flickers. TV Mode z TV screen is blurred or shows noise signals. z TV signal is not received z z Check if the Display Adapter Driver (VGA Driver) is properly installed.
dark shadows. White color is poor. Power Indicator blinks green. z Screen is blank and power indicator light is steady green or blinks every 0.5 or 1 seconds z z The screen is blank and is blinking. z The monitor is currently saving the changes made in settings to the OSD memory. The monitor is using its power management system.
How can I set the Power Saving function? Windows ME/XP/2000 : Set the function at BIOS-SETUP of the computer or the screen saver. (Refer to Windows/Computer Manual). How can I clean the outer case/LCD Panel? Disconnect the power cord and then clean the monitor with a soft cloth, using either a cleaning solution or plain water. Do not leave any remains of the detergent nor scratch the case. Do not allow any water to go inside the monitor.
General General Model Name SyncMaster 940MW LCD Panel Size 19.0 inch diagonal (48 cm) Display area 408.24 mm(H) x 255.15 mm(V) Pixel Pitch 0.2835 mm(H) x 0.2835 mm(V) Synchronization Horizontal 30 ~ 61 kHz Vertical 56 ~ 75 Hz Display Color 16.7 M Colors Resolution Optimum resolution WXGA+ 1440 x 900 @ 60 Hz Maximum resolution WXGA+ 1440 x 900 @ 60 Hz Input Signal, Terminated RGB Analog, DVI(Digital Visual Interface) Composite Digital RGB, 0.
Signal connectors 15pin 3-row D-sub connector, 24pin 3-row DVI-D connector Power Saving Less than 2 W Dimensions (WxHxD)/ Weight 466 x 406 x 217 mm / 18.3 x 16.0 x 8.5 inch / 6.2 kg / 13.7 lbs (With Stand) 466 x 371 x 66 mm /18.3 x 14.6 x 2.6 inch (Without Stand) VESA Mounting Interface 100 mm X 100 mm (for use with Specialty(Arm) Mounting hardware.
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows. Table 1. Preset Timing Modes Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) MAC, 640 x 480 35.000 66.667 30.240 -/- MAC, 832 x 624 49.726 74.551 57.
Countries Israel Denmark Portugal Netherlands Austria Singapore Indonesia Australia England South Africa Hongkong China North Korea Rumania Brazil SECAM Broadcasting Systems SECAM-B Countries Argentina Uruguay Paraguay SECAM-D Iran Iraq Saudi arabia Syria Lebanon Egypt SECAM-K1 Russia Hungary Bulgaria Poland SECAM-L France Horizontal Frequency The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle and the inverse number of
Contact SAMSUNG WORLDWIDE If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center. North America U.S.A 1-800-SAMSUNG (7267864) http://www.samsung.com CANADA 1-800-SAMSUNG (7267864) http://www.samsung.com/ca MEXICO 01-800-SAMSUNG (7267864) http://www.samsung.com/mx Latin America ARGENTINE 0800-333-3733 http://www.samsung.com/ar BRAZIL 4004-0000 http://www.samsung.com/br CHILE 800-726-7864 (SAMSUNG) http://www.samsung.
CZECH REPUBLIC 844 000 844 http://www.samsung.com/cz DENMARK 38 322 887 http://www.samsung.com/dk FINLAND 09 693 79 554 http://www.samsung.com/fi FRANCE 08 25 08 65 65 (€ 0,15/min) http://www.samsung.com/fr GERMANY 01805 - 121213 (€ 0,12/Min) http://www.samsung.de HUNGARY 06 40 985 985 http://www.samsung.com/hu ITALIA 199 153 153 http://www.samsung.com/it LUXEMBURG 02 261 03 710 http://www.samsung.lu NETHERLANDS 0900 20 200 88 (€ 0.10/Min) http://www.samsung.
Terms Sync Signal Sync (Synchronized) Signals refer to the standard signals that are required to display desired colors on the monitor. They are divided into Vertical and Horizontal Sync Signals. These signals display normal color images by the set resolution and frequency. Types of Sync Signals Separate This is a scheme of transmitting individual vertical and horizontal sync signals to the monitor.
S-Video Short for "Super Video." S-Video allows up to 800 lines of horizontal resolution, enabling high-quality video. VHF/UHF VHF indicates TV channels 2 to 13, and UHF indicates channels 14 through 69. Channel Fine Tuning This feature allows the viewer to fine-tune the TV channel to obtain the best viewing conditions. The Samsung LCD TV has both automatic and manual channel fine-tuning features to enable the viewer to adjust their desired settings.
{ Resolution: 1440 x 900 { Vertical frequency (refresh rate): 60 Hz 2. TFT LCD panels manufactured by using advanced semiconductor technology with a precision of 1ppm (one millionth) and above is used for this product. But the pixels of RED, GREEN, BLUE and WHITE color seem to be bright sometimes or some of black pixels could be seen. This is not from bad quality and you can use it without any problems. { For example, the number of TFT LCD sub pixels contained in this product are 3,888,000. 3.
IMPORTADO POR: SAMSUNG ELECTRONICS MÉXICO. S.A. de C.V. Vía Lopez Portillo No. 6, Col. San Fco. Chilpan Tultitlán, Estado de México, C.P. 54940 Tel: 01-55-5747-5100 / 01-800-726-7864 EXPORTADO POR: Samsung Electronics CO.,LTD.
PRODUCT INFORMATION (Image Retention Free) LCD Monitors and TVs may have image retention when switching from one image to another especially after displaying a stationary image for a long time. This guide is to demonstrate correct usage of LCD products in order to protect them from Image retention. Warranty Warranty does not cover any damage caused by image retention. Burn-in is not covered by the warranty.
Ex) The best way to protect your monitor from Image retention is to set your PC or System to operate a Screen Saver program when you are not using it. Image retention may not occur when a LCD panel is operated under normal conditions. Normal conditions are defined as continuously changing video patterns. When the LCD panel is operated for a long time with a fixed pattern (-over 12 hours-), there may be slight difference in voltage between electrodes that work the liquid crystal (LC) in a pixel.
Correct Disposal of This Product (Waste Electrical & Electronic Equipment) - Europe only (Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life.
