iDCS 100 TECHNICAL MANUAL INSTALLATION TABLE OF CONTENTS JUNE 2002 T A B L E O F C O N T E N T S INSTALLATION SECTION PART DESCRIPTION PAGE INSTALLATION WARNINGS ................................................................i-ii 1 SITE REQUIREMENTS .................................................................... 1.1 2 INSTALLATION OF BASIC KSU AND EXPANSION CABINET 3 2.1 UNPACKING AND INSPECTION ................................................... 2.1 2.2 KEY SERVICE UNIT INSTALLATION .
iDCS 100 TECHNICAL MANUAL 4 5 6 INSTALLATION TABLE OF CONTENTS JUNE 2002 POWER UP PROCEDURES 4.1 CONNECT POWER TO THE SYSTEM .......................................... 4.1 4.2 iDCS MEM3 CARD INDICATIONS ................................................. 4.1 4.3 iDCS MEM4 CARD INDICATIONS ................................................. 4.2 4.4 PCB VERIFICATION ...................................................................... 4.2 4.5 DEFAULT TRUNK AND STATION NUMBERING ....................
iDCS 100 TECHNICAL MANUAL 7 8 9 10 CONNECTING OPTIONAL EQUIPMENT 7.1 MUSIC ON HOLD/BACKGROUND MUSIC .................................... 7.1 7.2 EXTERNAL PAGING ...................................................................... 7.1 7.3 COMMON BELL ............................................................................ 7.2 7.4 RING OVER PAGE ......................................................................... 7.2 7.5 STATION MESSAGE DETAIL RECORDING (SMDR)...................... 7.
iDCS 100 TECHNICAL MANUAL INSTALLATION TABLE OF CONTENTS JUNE 2002 11.8 ADDING AN S4BRI CARD ........................................................... 11.3 11.9 ADDING AN SPLL DAUGHTER BOARD...................................... 11.4 11.10 ADDING A MODEM CARD ........................................................... 11.4 12 13 INSTALLING A SVMi-8 CARD 12.1 SYSTEM SIZE WITH SVMi-8 ....................................................... 12.1 12.2 REMOVING THE COVER ............................
iDCS 100 TECHNICAL MANUAL INSTALLATION WARNINGS JUNE 2002 INSTALLATION WARNINGS 1. SAFETY PRECAUTIONS To limit the risk of personal injury, always follow these precautions before connecting TELCO circuits: a. Never install telephone wiring during a lightning storm. b. Never install telephone jacks in a wet location unless the jack is specifically designed for wet locations. c. Never touch uninsulated telephone wires or terminals unless the telephone line has been disconnected at the network interface. d.
iDCS 100 TECHNICAL MANUAL 6. 7. ! INSTALLATION WARNINGS JUNE 2002 a. Provided with the current limitations and maximum overcurrent protection for telecommunication circuits. b. Reference to the specific power supply or current limiting device provided with the product c. Detailed instructions showing the proper method of installation and connections to the telecommunication wiring system.
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 1 JUNE 2002 PART 1. SITE REQUIREMENTS When planning the installation of the iDCS 100, choose a site that meets the following requirements: ! ! ! ! ! ! ! ! Select a location for the key service unit (KSU) that has enough space for easy installation and adequate lighting (see Figure 1–1). Select a location that will minimize cable lengths. See the Cable Requirements table below.
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 1 JUNE 2002 14 3/8" 6.
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 2 JUNE 2002 PART 2. INSTALLATION OF BASIC KSU AND EXPANSION CABINET 2.1 UNPACKING AND INSPECTION After unpacking the KSU, inspect for signs of physical damage. If any damage is detected, do not attempt to install. Contact SAMSUNG TELECOMMUNICATIONS AMERICA, Technical Support Department.
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 2 JUNE 2002 equipment damage. If the expansion cabinet is being added to an existing system make sure the switch on the MEM card is turned ON before powering down the KSU to keep the customer data intact. 3. Connect the expansion cabinet to the basic KSU by plugging free end of the ribbon cable into the socket on the KSU motherboard (see Figure 2–3). 4.
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 2 JUNE 2002 A supplementary equipment grounding conductor shall be installed between the system and ground that is in addition to the equipment grounding conductor in the power supply cord. The supplementary equipment grounding conductor shall not be smaller in size than the ungrounded branch-circuit supply conductors.
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 2 JUNE 2002 connecting a high current/voltage capacity ground wire which is bonded to ground at the electric service power entrance or via some other method approved by the National Electrical Code to the iDCS 100 system ground lug. This is a more secure ground connection, which can only be disconnected intentionally.
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 2 JUNE 2002 • FUSE CAUTION: Double pole / neutral fusing + ATTENTION: Double pole / fusible sur le neuter. CAUTION: 1. For continued protection against risk of fire, replace only with same type and rating of fuse. 2. DISCONNECT POWER BEFORE CHANGING FUSE.
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 2 JUNE 2002 The -48VDC cable assembly has a male 2 pin connector on the iDCS PWR. Insert this end of the DC cable into the battery (BATT) connector found on the iDCS PWR (see Figure 2–7). Attach the other end of the DC power cable to the –48VDC power source. WARNING: Be sure the proper polarity is observed. Equipment damage will result if polarity is reversed. Do not connect external AC or DC power to the System (see Section 4 Power Up Procedures).
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 2 JUNE 2002 12 7/8" 12" MDF SCREWS LOCATION KSU FIGURE 2–1 HOME PAGE Table of Contents
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 2 JUNE 2002 TEPRI UNIVERSAL SLOT 5 SVMi-8 UNIVERSAL SLOT 4 UNIVERSAL SLOT 3 UNIVERSAL SLOT 2 UNIVERSAL SLOT 1 MISC SLOT MEM SLOT 2 SLI SLOT WALL MOUNTING SCREWS WALL MOUNTING SCREWS KSU AND EXPANSION CABINET WALL MOUNTING FIGURE 2–2A HOME PAGE Table of Contents
EXPANSION CABINET MOUNTING UNIVERSAL SLOT 3 UNIVERSAL SLOT 2 UNIVERSAL SLOT 1 MISC SLOT MEM SLOT INSTALLATION PART 2 JUNE 2002 2 SLI SLOT iDCS 100 TECHNICAL MANUAL EXPANSION CABINET ATTACHMENT SCREWS FIGURE 2–2B HOME PAGE Table of Contents
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 2 JUNE 2002 UNIVERSAL SLOT 3 TEPRI SVMi-8 UNIVERSAL SLOT 5 RIBBON CABLE UNIVERSAL SLOT 4 UNIVERSAL SLOT 2 UNIVERSAL SLOT 1 MISC SLOT MEM SLOT 2 SLI SLOT RED/GREEN CABLE RED/GREEN CABLE RIBBON CABLE AND RED/GREEN CABLE PAIR CONNECTION EXPANSION CABINET TO KSU FIGURE 2–3 HOME PAGE Table of Contents
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 2 JUNE 2002 EXPANSION CABINET GROUND WIRE TO KSU TEPRI UNIVERSAL SLOT 5 SVMi-8 UNIVERSAL SLOT 4 UNIVERSAL SLOT 3 UNIVERSAL SLOT 2 UNIVERSAL SLOT 1 MISC SLOT MEM SLOT 2 SLI SLOT GROUND WIRE FIGURE 2–4 HOME PAGE Table of Contents
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 2 JUNE 2002 GROUNDING LUG BOTTOM VIEW KSU GND LUG FIGURE 2–5 HOME PAGE Table of Contents
CONNECTOR DESIGNATOR TEPRI SVMi-8 P2 UNIVERSAL SLOT 5 UNIVERSAL SLOT 4 UNIVERSAL SLOT 3 UNIVERSAL SLOT 2 UNIVERSAL SLOT 1 MISC SLOT MEM SLOT 2 SLI SLOT iDCS 100 TECHNICAL MANUAL INSTALLATION PART 2 JUNE 2002 P5 P1 FIGURE 2–6 HOME PAGE Table of Contents
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 2 JUNE 2002 RESERVE POWER BATTERY CONNECTOR POWER SUPPLY BLACK RED CONNECT TO EITHER A OR B + – 12V + – 12V + – + 12V – + 12V + – + 6V 6V + – – + + – 6V 6V + – – – 6V 6V + – OPTION A + 6V – + 6V – OPTION B BATTERIES SHOULD BE PLACED WITHIN THREE FEET OF KSU RESERVE POWER BATTERY CONNECTIONS FIGURE 2–7 HOME PAGE Table of Contents
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 3 JUNE 2002 PART 3. INSTALLING PRINTED CIRCUIT CARDS Unpack and inspect each card before installing. Check for signs of physical damage. If any damage is detected, do not attempt to install. Contact Samsung Technical Support immediately. 3.1 iDCS MEM3 CARD (Figure 3–2) Make sure that the BACK UP switch is in the OFF position. Insert the iDCS MEM3 card in the KSU slot labeled MEM (see Figure 3–1).
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 3 JUNE 2002 3.5 SMISC2 CARD (Figure 3–5) The Auto Attendant Message Memory backup switch should be turned ON to protect the customer-recorded messages in the event of a power failure. This can be done before or after the card is installed, as the switch is easily accessible. Insert the SMISC2 card into the appropriate slot (see Figure 3–1). Push firmly in the middle of both card ejectors to ensure that it is fully inserted into the back plane connector.
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 3 JUNE 2002 3.11 S6TRK CARD (Figure 3–8) There are no options to select on this card. Insert the S6TRK card into any universal slot in the KSU or expansion cabinet (see Figure 3–1). Push firmly in the middle of both card ejectors on each card to ensure that it is fully inserted into the back plane connector. 3.12 2 E&M 4 DLI CARD (Figure 3–9) This is the same card as used on the DCS Compact.
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 3 JUNE 2002 3.13 S4BRI CARD (Figure 3–10) The S4BRI card is equipped with dip switch controlled line termination resistors. If a BRI circuit is to be used as a Trunk circuit these switches must be in the OFF position. If a circuit is to be used as a station then the dip switches for that circuit must be in the ON position.
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 3 JUNE 2002 iDCS TEPRI CARD DIP SWITCH Switch No. ON OFF 1 T1 E1 2 PRI T1 3 NFAS (24B) NFAS (23B + D) 4 NETWORK USER 5 AFT NORMAL 6 Switch 6 must be OFF 7 Switch 7 must be OFF 8 Switch 8 must be ON iDCS TEPRI LED DEFINITIONS LED Name Function Status Normal Status Error Status SYN Synchronization Loss. Indicates wander or loss of framing. OFF ON LOS Loss of Signal. No PCM Clocking is being received.
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 3 JUNE 2002 3.15 SPLL DAUGHTER BOARD (Figure 3–12) There are no options to select on this card. Insert the SPLL daughter board onto its connectors in the bottom left hand corner of the KSU motherboard (see Figure 3–13). Push firmly in the middle of both the connectors to ensure that it is fully inserted into the back plane connector. 3.16 MODEM CARD (Figure 3–14) There are no options to select on this card.
KSU AND EXPANSION CABINET SLOT POSITIONS TEPRI SVMi-8 UNIVERSAL SLOT 5 UNIVERSAL SLOT 4 UNIVERSAL SLOT 3 UNIVERSAL SLOT 2 UNIVERSAL SLOT 1 MISC SLOT MEM SLOT INSTALLATION PART 3 JUNE 2002 2 SLI SLOT iDCS 100 TECHNICAL MANUAL FIGURE 3–1 HOME PAGE Table of Contents
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 3 JUNE 2002 iDCS MEM3 CARD FIGURE 3–2 iDCS MEM4 CARD FIGURE 3–3 HOME PAGE Table of Contents
iDCS 100 TECHNICAL MANUAL 2 SLI CARD INSTALLATION PART 3 JUNE 2002 FIGURE 3–4 HOME PAGE Table of Contents
iDCS 100 TECHNICAL MANUAL SMISC 1 AND 2 CARDS INSTALLATION PART 3 JUNE 2002 FIGURE 3–5 HOME PAGE Table of Contents
iDCS 100 TECHNICAL MANUAL 2 X 4 DLI CARD AND S8DLI CARD INSTALLATION PART 3 JUNE 2002 FIGURE 3–6 HOME PAGE Table of Contents
iDCS 100 TECHNICAL MANUAL 2 X 4 SLI CARD AND S8SLI CARD INSTALLATION PART 3 JUNE 2002 FIGURE 3–7 HOME PAGE Table of Contents
iDCS 100 TECHNICAL MANUAL S3TRK CARD AND S6TRK CARD INSTALLATION PART 3 JUNE 2002 FIGURE 3–8 HOME PAGE Table of Contents
INSTALLATION PART 3 JUNE 2002 FG J2 T5 J4 RLY2 FG 48 NO T1 48 NO 48 FG NC T5 48 J3 FG T1 J1 NC TYPE RLY1 iDCS 100 TECHNICAL MANUAL 2 E&M / 4 DLI CARD FIGURE 3–9 HOME PAGE Table of Contents
iDCS 100 TECHNICAL MANUAL S4BRI CARD INSTALLATION PART 3 JUNE 2002 FIGURE 3–10 HOME PAGE Table of Contents
iDCS 100 TECHNICAL MANUAL iDCS TEPRI CARD INSTALLATION PART 3 JUNE 2002 FIGURE 3–11 HOME PAGE Table of Contents
iDCS 100 TECHNICAL MANUAL SPLL DAUGHTER BOARD INSTALLATION PART 3 JUNE 2002 FIGURE 3–12 HOME PAGE Table of Contents
UNIVERSAL SLOT 3 UNIVERSAL SLOT 1 UNIVERSAL SLOT 2 MISC SLOT MEM SLOT INSTALLATION PART 3 JUNE 2002 2 SLI SLOT iDCS 100 TECHNICAL MANUAL SPLL DAUGHTER BOARD SPLL INSTALLATION ON KSU MOTHERBOARD FIGURE 3–13 HOME PAGE Table of Contents
iDCS 100 TECHNICAL MANUAL MODEM CARD INSTALLATION PART 3 JUNE 2002 FIGURE 3–14 HOME PAGE Table of Contents
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 3 JUNE 2002 MODEM CARD SMISC 1 OR 2 CARD MODEM CARD INSTALLATION ON SMISC CARD FIGURE 3–15 HOME PAGE Table of Contents
iDCS 100 TECHNICAL MANUAL ITMC CARD INSTALLATION PART 3 JUNE 2002 FIGURE 3–16 HOME PAGE Table of Contents
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 4 JUNE 2002 PART 4. POWER UP PROCEDURES 4.1 CONNECT POWER TO THE SYSTEM Verify that the AC voltage at the dedicated electrical outlet is in the range of 82–132 Volts AC. Make sure the AC power switch on the system power supply is in the OFF position and that the SMEM card battery switch is also in the OFF position. Plug the KSU power cord into the dedicated polarized AC outlet. Turn the AC power switch to the ON position.
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 4 JUNE 2002 4.3 iDCS MEM4 CARD INDICATIONS Having verified proper operation of the power supply, visually check the iDCS MEM4 card indications. The LED indications are as follow: LED Indication OFF ON 1 Indicates whether the status of LAN transmit chip Abnormal (LST972, U13) is in normal or abnormal.
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 5 JUNE 2002 PART 5. CONNECTING TELCO CIRCUITS 5.1 SAFETY PRECAUTIONS To limit the risk of personal injury, always follow these precautions before connecting TELCO circuits: a. Never install telephone wiring during a lightning storm. b. Never install telephone jacks in a wet location unless the jack is specifically designed for wet locations. c.
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 5 JUNE 2002 service facility interface code for the E&M tie line is TL11M. This is a 2 wire Type 1 tie line. NOTE: When connecting an E&M tie line in “back to back” fashion you must remember to reverse the E&M leads at one end ONLY i.e. connect the E lead on one system to the M lead of the other system and vice versa. 5.5 ISDN BRI LINES The iDCS 100 requires that an NT1 be connected between the iDCS 100 and the BRI circuit provided by the Telephone Company.
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 5 JUNE 2002 PARAMETER OPTIONS IN iDCS 100 Framing type Super Frame (SF) or D4 Extended Super Frame (ESF) AMI or B8ZS Coding type The coding type must be set up in the system to match the T1 span and is contained in MMC 808. 5.
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 5 JUNE 2002 25 PAIR CABLE WITH MALE CONNECTOR TO BASIC P2 25 PAIR CABLE WITH MALE CONNECTOR TO EXPANSION P5 CIRCUIT TERM COLOR PIN C.O. TIP C.O. RING FUNCTION SLOT 1 TRUNK 1 1 2 W-BL BL-W 26 1 C.O. TIP C.O. RING SLOT 1 TRUNK 2 3 4 W-0 0-W 27 2 C.O. TIP C.O.
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 5 JUNE 2002 25 PAIR CABLE WITH MALE CONNECTOR TO BASIC P2 25 PAIR CABLE WITH MALE CONNECTOR TO EXPANSION P5 CIRCUIT TERM COLOR PIN C.O. TIP C.O. RING FUNCTION SLOT 1 TRUNK 1 1 2 W-BL BL-W 26 1 C.O. TIP C.O. RING SLOT 1 TRUNK 2 3 4 W-0 0-W 27 2 C.O. TIP C.O. RING SLOT 1 TRUNK 3 5 6 W-GN GN-W 28 3 C.O. TIP C.O. RING SLOT 1 TRUNK 4 7 8 W-BR BR-W 29 4 C.O. TIP C.O. RING SLOT 1 TRUNK 5 9 10 W-SL SL-W 30 5 C.O. TIP C.O.
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 5 JUNE 2002 25 PAIR CABLE WITH MALE CONNECTOR TO BASIC P2 25 PAIR CABLE WITH MALE CONNECTOR TO EXPANSION P5 FUNCTION C.O. TIP C.O. RING C.O. TIP C.O.
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 5 JUNE 2002 25 PAIR CABLE WITH CONNECTOR TO KSU P1 FUNCTION SLT TIP SLT RING SLT TIP SLT RING CIRCUIT 1 2 TERM COLOR PIN 19 R-SL 10 20 SL-R 35 21 BK-BL 11 22 BL-BK 36 TELCO-PROVIDED NETWORK ACCESS JACK RJ 11C RJ 14C RJ 21X CONNECT TO ANY CIRCUIT ON THE 2 SLI CARD.
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 5 JUNE 2002 25 PAIR CABLE WITH MALE CONNECTOR TO BASIC P2 25 PAIR CABLE WITH MALE CONNECTOR TO EXPANSION P5 FUNCTION CIRCUIT TERM COLOR PIN C.O. TIP C.O. RING M E SLOT 1 TRUNK 1 1 2 3 4 W-BL BL-W W-0 0-W 26 1 27 2 C.O. TIP C.O.
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 5 JUNE 2002 25 PAIR CABLE WITH MALE CONNECTOR TO BASIC P2 25 PAIR CABLE WITH MALE CONNECTOR TO EXPANSION P5 NT1 S/T U POWER TO TELCO BRI CONNECT TO ISDN NT1 MDF CONNECTIONS FOR ISDN NT1 TO S4BRI CARD PIN COLOR TERM CIRCUIT FUNCTION 26 1 27 2 W-BL BL-W W-0 0-W 1 2 3 4 TRANSMIT A SLOT 1 TRANSMIT B CIRCUIT 1 RECEIVE A RECEIVE B 28 3 29 4 W-GN GN-W W-BR BR-W 5 6 7 8 TRANSMIT A SLOT 1 TRANSMIT B CIRCUIT 2 RECEIVE A RECEIVE B 30 5 31 6 W-SL SL-W R
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 5 JUNE 2002 TRANSMIT PAIR 8 7 6 5 4 3 2 1 T E P R I RECEIVE PAIR CUSTOMER PROVIDED MALE RJ 45 ENDED CABLE SYN AIS IPC TPI LOS L2 CLK TP2 T1 E1 CUSTOMER-PROVIDED CUSTOMER SERVICE UNIT SIO RST TELCO T1 SPAN MDF CONNECTIONS T1/PRI CIRCUIT TO TEPRI CARD FIGURE 5–7 HOME PAGE Table of Contents
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 6 JUNE 2002 PART 6. CONNECTING STATION EQUIPMENT 6.1 SAFETY PRECAUTIONS To limit the risk of personal injury, always follow these precautions before connecting telephone circuits: a. Never install telephone wiring during a lightning storm. b. Never install telephone jacks in a wet location unless the jack is specifically designed for wet locations. c.
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 6 JUNE 2002 When a customer-provided electric door release is installed, cross-connect the corresponding door release contacts on the DPIM to the door lock mechanism (see Figures 6–10, 6-11 and 6–12). Use MMC 501 to program the duration of the contact closure as required. See the user guides for door lock release operation. The door release contacts on the DPIM are to be used for low voltage relay control only. The contacts are rated at 24 VDC-1 amp.
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 6 JUNE 2002 6.7B WALL-MOUNTING KEYSETS WITH ULTRA BASE WEDGE DCS keysets now come equipped with a new Ultra Base wedge. These base wedges are reversible and can be used for wall-mounting however not every wall mounting scenario is appropriate. First and foremost there is only one keyhole in the center of the base attaching to the wall, and these base wedges can not be used with the standard wall mount bracket with the two button/pins.
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 6 JUNE 2002 6.10 ATTACHING iDCS 64B MODULES TO AN iDCS KEYSET First remove the base wedge from the iDCS 64B Module and attach the bracket to it with two of the screws provided (see Figure 6-20). Remove the base wedge of the keyset and place it to the right of the 64 Button Module and attach the bracket/64BM to the keyset with the remaining two screws. The base wedge can now be replaced.
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 6 JUNE 2002 25 PAIR CABLE WITH MALE CONNECTOR TO KSU P1 PIN COLOR TERM CIRCUIT FUNCTION 26 1 W-BL BL-W 1 2 1 DLI TIP DLI RING 27 2 W-0 0-W 3 4 2 DLI TIP DLI RING 28 3 W-GN GN-W 5 6 3 DLI TIP DLI RING 29 4 W-BR BR-W 7 8 4 DLI TIP DLI RING 30 5 W-S S-W 9 10 5 DLI TIP DLI RING 31 6 R-BL BL-R 11 12 6 DLI TIP DLI RING 32 7 R-O O-R 13 14 7 DLI TIP DLI RING 33 8 R-G G-R 15 16 8 DLI TIP DLI RING ONE PAIR TWISTED SHEATHED STAT
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 6 JUNE 2002 25 PAIR CABLE WITH MALE CONNECTOR TO BASIC P2 25 PAIR CABLE WITH MALE CONNECTOR TO EXPANSION P5 PIN COLOR TERM CIRCUIT FUNCTION 26 1 W-BL BL-W 1 2 SLOT 1 CIRCUIT 1 DLI TIP DLI RING 27 2 W-O O-W 3 4 SLOT 1 CIRCUIT 2 DLI TIP DLI RING 28 3 W-GN GN-W 5 6 SLOT 1 CIRCUIT 3 DLI TIP DLI RING 29 4 W-BR BR-W 7 8 SLOT 1 CIRCUIT 4 DLI TIP DLI RING 30 5 W-S S-W 9 10 SLOT 1 CIRCUIT 5 DLI TIP DLI RING 31 6 R-BL BL-R 11 12 SLOT 1 CIR
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 6 JUNE 2002 25 PAIR CABLE WITH MALE CONNECTOR TO BASIC P2 25 PAIR CABLE WITH MALE CONNECTOR TO EXPANSION P5 PIN COLOR TERM 26 1 W-BL BL-W 1 2 CIRCUIT FUNCTION 27 2 W-O O-W 3 4 28 3 W-GN GN-W 5 6 29 4 W-BR BR-W 7 8 30 5 W-S S-W 9 10 SLOT 1 CIRCUIT 3 DLI TIP DLI RING 31 6 R-BL BL-R 11 12 SLOT 1 CIRCUIT 4 DLI TIP DLI RING 32 7 R-O O-R 13 14 SLOT 1 CIRCUIT 5 DLI TIP DLI RING 33 8 R-G G-R 15 16 SLOT 1 CIRCUIT 6 DLI TIP DLI RING 34
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 6 JUNE 2002 25 PAIR CABLE WITH MALE CONNECTOR TO KSU P1 PIN COLOR TERM CIRCUIT FUNCTION 26 1 W-BL BL-W 1 2 1 DLI TIP DLI RING 27 2 W-0 0-W 3 4 2 DLI TIP DLI RING 28 3 W-GN GN-W 5 6 3 DLI TIP DLI RING 29 4 W-BR BR-W 7 8 4 DLI TIP DLI RING 30 5 W-S S-W 9 10 5 DLI TIP DLI RING 31 6 R-BL BL-R 11 12 6 DLI TIP DLI RING 32 7 R-O O-R 13 14 7 DLI TIP DLI RING 33 8 R-G G-R 15 16 8 ONE PAIR TWISTED SHEATHED STATION CABLE 24 OR 26
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 6 JUNE 2002 25 PAIR CABLE WITH MALE CONNECTOR TO BASIC P2 25 PAIR CABLE WITH MALE CONNECTOR TO EXPANSION P5 PIN COLOR TERM CIRCUIT FUNCTION 26 1 W-BL BL-W 1 2 SLOT 1 CIRCUIT 1 DLI TIP DLI RING 27 2 W-O O-W 3 4 SLOT 1 CIRCUIT 2 DLI TIP DLI RING 28 3 W-GN GN-W 5 6 SLOT 1 CIRCUIT 3 DLI TIP DLI RING 29 4 W-BR BR-W 7 8 SLOT 1 CIRCUIT 4 DLI TIP DLI RING 30 5 W-S S-W 9 10 SLOT 1 CIRCUIT 5 DLI TIP DLI RING 31 6 R-BL BL-R 11 12 SLOT 1 CIR
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 6 JUNE 2002 25 PAIR CABLE WITH MALE CONNECTOR TO BASIC P2 25 PAIR CABLE WITH MALE CONNECTOR TO EXPANSION P5 PIN COLOR TERM 26 1 W-BL BL-W 1 2 CIRCUIT FUNCTION 27 2 W-O O-W 3 4 28 3 W-GN GN-W 5 6 29 4 W-BR BR-W 7 8 30 5 W-S S-W 9 10 SLOT 1 CIRCUIT 3 DLI TIP DLI RING 31 6 R-BL BL-R 11 12 SLOT 1 CIRCUIT 4 DLI TIP DLI RING 32 7 R-O O-R 13 14 SLOT 1 CIRCUIT 5 DLI TIP DLI RING 33 8 R-G G-R 15 16 SLOT 1 CIRCUIT 6 DLI TIP DLI RING 34
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 6 JUNE 2002 25 PAIR CABLE WITH MALE CONNECTOR TO KSU P1 TERM CIRCUIT PIN COLOR 10 R-SL 19 35 SL-R 20 11 BK-BL 21 36 BL-BK 22 1 2 FUNCTION SLT TIP SLT RING SLT TIP SLT RING ONE PAIR TWISTED SHEATHED STATION CABLE 24 OR 26 AWG R G BK Y W BL 1 2 3 4 5 6 CONNECT TO ANY CIRCUIT ON THE 2 SLI CARD.
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 6 JUNE 2002 25 PAIR CABLE WITH MALE CONNECTOR TO BASIC P2 25 PAIR CABLE WITH MALE CONNECTOR TO EXPANSION P5 PIN COLOR TERM CIRCUIT FUNCTION 26 1 W-BL BL-W 1 2 SLOT 1 CIRCUIT 1 SLI TIP SLI RING 27 2 W-O O-W 3 4 SLOT 1 CIRCUIT 2 SLI TIP SLI RING 28 3 W-GN GN-W 5 6 SLOT 1 CIRCUIT 3 SLI TIP SLI RING 29 4 W-BR BR-W 7 8 SLOT 1 CIRCUIT 4 SLI TIP SLI RING 30 5 W-S S-W 9 10 SLOT 1 CIRCUIT 5 SLI TIP SLI RING 31 6 R-BL BL-R 11 12 SLOT 1 CIR
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 6 JUNE 2002 25 PAIR CABLE WITH MALE CONNECTOR TO BASIC P2 25 PAIR CABLE WITH MALE CONNECTOR TO EXPANSION P5 PIN COLOR TERM 26 1 W-BL BL-W 1 2 CIRCUIT FUNCTION 27 2 W-O O-W 3 4 28 3 W-GN GN-W 5 6 29 4 W-BR BR-W 7 8 30 5 W-S S-W 9 10 SLOT 1 CIRCUIT 3 SLI TIP SLI RING 31 6 R-BL BL-R 11 12 SLOT 1 CIRCUIT 4 SLI TIP SLI RING 32 7 R-O O-R 13 14 SLOT 1 CIRCUIT 5 SLI TIP SLI RING 33 8 R-G G-R 15 16 SLOT 1 CIRCUIT 6 SLI TIP SLI RING 34
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 6 JUNE 2002 25 PAIR CABLE WITH MALE CONNECTOR TO KSU P1 PIN COLOR TERM CIRCUIT FUNCTION 26 1 W-BL BL-W 1 2 1 DLI TIP DLI RING 27 2 W-0 0-W 3 4 2 DLI TIP DLI RING 28 3 W-GN GN-W 5 6 3 DLI TIP DLI RING 29 4 W-BR BR-W 7 8 4 DLI TIP DLI RING 30 5 W-S S-W 9 10 5 DLI TIP DLI RING 31 6 R-BL BL-R 11 12 6 DLI TIP DLI RING 32 7 R-O O-R 13 14 7 DLI TIP DLI RING 33 8 R-G G-R 15 16 8 DLI TIP DLI RING ONE PAIR TWISTED SHEATHED STAT
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 6 JUNE 2002 25 PAIR CABLE WITH MALE CONNECTOR TO BASIC P2 25 PAIR CABLE WITH MALE CONNECTOR TO EXPANSION P5 PIN COLOR TERM CIRCUIT FUNCTION 26 1 W-BL BL-W 1 2 SLOT 1 CIRCUIT 1 DLI TIP DLI RING 27 2 W-O O-W 3 4 SLOT 1 CIRCUIT 2 DLI TIP DLI RING 28 3 W-GN GN-W 5 6 SLOT 1 CIRCUIT 3 DLI TIP DLI RING 29 4 W-BR BR-W 7 8 SLOT 1 CIRCUIT 4 DLI TIP DLI RING 30 5 W-S S-W 9 10 SLOT 1 CIRCUIT 5 DLI TIP DLI RING 31 6 R-BL BL-R 11 12 SLOT 1 CIR
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 6 JUNE 2002 25 PAIR CABLE WITH MALE CONNECTOR TO BASIC P2 25 PAIR CABLE WITH MALE CONNECTOR TO EXPANSION P5 PIN COLOR TERM 26 1 W-BL BL-W 1 2 CIRCUIT FUNCTION 27 2 W-O O-W 3 4 28 3 W-GN GN-W 5 6 29 4 W-BR BR-W 7 8 30 5 W-S S-W 9 10 SLOT 1 CIRCUIT 3 DLI TIP DLI RING 31 6 R-BL BL-R 11 12 SLOT 1 CIRCUIT 4 DLI TIP DLI RING 32 7 R-O O-R 13 14 SLOT 1 CIRCUIT 5 DLI TIP DLI RING 33 8 R-G G-R 15 16 SLOT 1 CIRCUIT 6 DLI TIP DLI RING 34
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 6 JUNE 2002 25 PAIR CABLE WITH MALE CONNECTOR TO BASIC P2 25 PAIR CABLE WITH MALE CONNECTOR TO EXPANSION P5 CUSTOMER PROVIDED STATION EQUIPMENT OR NT1 CONNECT TO ISDN STATION EQUIPMENT OR NT1 MDF CONNECTIONS FOR ISDN STATION TO S4BRI CARD PIN COLOR TERM CIRCUIT FUNCTION 26 1 27 2 W-BL BL-W W-0 0-W 1 2 3 4 TRANSMIT A SLOT 1 TRANSMIT B CIRCUIT 1 RECEIVE A RECEIVE B 28 3 29 4 W-GN GN-W W-BR BR-W 5 6 7 8 TRANSMIT A SLOT 1 TRANSMIT B CIRCUIT 2 RECEIVE
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 6 JUNE 2002 1 5 4 2 3 HOLES FOR MOUNTING SCREWS NOTE: THE DIRECTORY CARD SLIDE TRAY IS NOT USED WHEN THE KEYSET IS WALL-MOUNTED.
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 6 JUNE 2002 1 2 3 USED FOR ATTACHING AOM OR 64B MODULE WITH CONNECTOR CLIP HOLES FOR MOUNTING SCREWS NOTE: THE DIRECTORY CARD SLIDE TRAY IS NOT USED WHEN THE KEYSET IS WALL-MOUNTED.
IDCS 100 TECHNICAL MANUAL INSTALLATION PART 6 JUNE 2002 1 2 3 WALL-MOUNTING AN iDCS KEYSET FIGURE FIGURE6–16 6-7 HOME PAGE Table of Contents
GROOVE FOR ADDITIONAL CONNECTOR CLIP INSTALLATION PART 6 JUNE 2002 24B / 12B ULTRA BASE WEDGE METAL CONNECTOR CLIP 64BM ULTRA BASE WEDGE iDCS 100 TECHNICAL MANUAL ATTACHING 24B/12B TO 64BM FIGURE6–17 6-7 FIGURE HOME PAGE Table of Contents
METAL CONNECTOR CLIP GROOVE FOR ADDITIONAL CONNECTOR CLIP INSTALLATION PART 6 JUNE 2002 24B / 12B ULTRA BASE WEDGE AOM ULTRA BASE WEDGE iDCS 100 TECHNICAL MANUAL ATTACHING 24B/12B TO AOM FIGURE 6–18 HOME PAGE Table of Contents
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 6 JUNE 2002 7B / SINGLE LINE ULTRA BASE WEDGE AOM ULTRA BASE WEDGE METAL CONNECTOR CLIP 7B/SINGLE LINE ULTRA BASE WEDGE 64BM ULTRA BASE WEDGE METAL CONNECTOR CLIP ATTACHING 7B/SINGLE LINE TO AOM AND 7B/SINGLE LINE TO 64BM FIGURE6–19 6-7 FIGURE HOME PAGE Table of Contents
IDCS 100 TECHNICAL MANUAL ATTACHING iDCS 64B MODULE TO AN iDCS KEYSET INSTALLATION PART 6 JUNE 2002 FIGURE6–20 6-7 FIGURE HOME PAGE Table of Contents
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 7 JUNE 2002 PART 7. CONNECTING OPTIONAL EQUIPMENT 7.1 MUSIC ON HOLD/BACKGROUND MUSIC Connect each customer-provided music source to the music input on the KSU connecting block (see Figure 7–1). The music input has internal automatic gain compensation features. NOTE: The MOH input on the KSU can be switched between internal chimes and an outside source.
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 7 JUNE 2002 The SMISC card also provides a second independently controlled page output voice pair to be used with customer-provided paging equipment. Connect the customer provided paging equipment to the page 2 output pins of the P1 connecting block (see Figure 7–3). The page voice pair is 600 Ohms impedance. When the amplifier page input is not 600 ohm, a suitable impedance matching transformer must be used. 7.
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 7 JUNE 2002 Use a pin to pin RS232C cable. Only pins 2, 3, 5 and 7 are required (see Figure 7–7). When the printer or optional call accounting device needs to be more than 15 feet away from the KSU, use shielded computer cable. Attach a male DB9 connector to the SMISC end and then attach one that matches the requirements of the call accounting device or printer to the other end. This cable must not exceed 300 feet.
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 7 JUNE 2002 for VM/AA operation. Use one pair twisted #24 AWG or #26 AWG jumper wire to crossconnect these SLI circuits to the VM/AA system (see Figure 7–11). Program these ports for VM/AA use in MMC 207 and set VM/AA options in MMC 726. As default MMC 726 comes programmed to interface with StarmaiL. See the Standard Telephone User Guide for feature codes and instructions (how to light message lights etc.). 7.
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 7 JUNE 2002 25 PAIR CABLE WITH MALE CONNECTOR TO KSU P1 PIN COLOR TERM CIRCUIT 41 Y-BL 31 16 BL-Y 32 42 Y-O 33 17 O-Y 34 1 2 FUNCTION MOH 1 MOH 1 + MOH 2 MOH 2 + CUSTOMER-PROVIDED MUSIC SOURCE CUSTOMER-PROVIDED MUSIC SOURCE CONNECT ONE MUSIC SOURCE TO EACH INPUT AS NEEDED. NOTE: MOH 2 REQUIRES AN SMISC CARD.
IDCS 100 TECHNICAL MANUAL INSTALLATION PART 7 JUNE 2002 S1 EXT INT MOH MOH SET SWITCH S1 TO INT FOR CHIMES TO BE HEARD ON PORT 371 OR SET SWITCH S1 TO EXT FOR AN EXTERNAL SOURCE TO BE HEARD ON PORT 371 SETTING JUMPER SWITCH S1 FIGURE 7–2 HOME PAGE Table of Contents
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 7 JUNE 2002 25 PAIR CABLE WITH MALE CONNECTOR TO KSU P1 600 PIN COLOR TERM CIRCUIT FUNCTION 40 15 BK-S S-BK 29 30 R1 RELAY 1 + RELAY 1 – 41 16 Y-BL BL-Y 31 32 MOH 1 + MOH 1 – 42 17 Y-O O-Y 33 34 MOH 2 + MOH 2 – 43 18 Y-G G-Y 35 36 1 PAGE 1 + PAGE 1 – 44 19 Y-BN BN-Y 37 38 2 PAGE 2 + PAGE 2 – 45 20 Y-S S-Y 39 40 46 21 V-BL BL-V 41 42 R2 RELAY 2 + RELAY 2 – 47 22 V-O O-V 43 44 R3 RELAY 3 + RELAY 3 – 48 23 V-G G-V 45 46
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 7 JUNE 2002 25 PAIR CABLE WITH MALE CONNECTOR TO KSU P1 CUSTOMER-PROVIDED PAGING AMPLIFIER PIN COLOR TERM CIRCUIT FUNCTION 40 15 BK-S S-BK 29 30 R1 RELAY 1 + RELAY 1 – 41 16 Y-BL BL-Y 31 32 42 17 Y-O O-Y 33 34 43 18 Y-G G-Y 35 36 1 44 19 Y-BN BN-Y 37 38 2 45 20 Y-S S-Y 39 40 46 21 V-BL BL-V 41 42 R2 RELAY 2 + RELAY 2 – ZONE 5 47 22 V-O O-V 43 44 R3 RELAY 3 + RELAY 3 – ZONE 6 48 23 V-G G-V 45 46 R4 RELAY 4 + RELAY 4 – Z
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 7 JUNE 2002 25 PAIR CABLE WITH MALE CONNECTOR TO KSU P1 PIN COLOR TERM CIRCUIT FUNCTION 41 16 Y-BL BL-Y 31 32 MOH 1 + MOH 1 – 42 17 Y-O O-Y 33 34 MOH 2 + MOH 2 – 43 18 Y-G G-Y 35 36 PAGE 1 + PAGE 1 – 44 19 Y-BN BN-Y 37 38 PAGE 2 + PAGE 2 – 45 20 Y-S S-Y 39 40 46 21 V-BL BL-V 41 42 R1 RELAY 2 + RELAY 2 – 47 22 V-O O-V 43 44 R2 RELAY 3 + RELAY 3 – 48 23 V-G G-V 45 46 R3 RELAY 4 + RELAY 4 – 49 24 V-BN BN-V 47 48 CUSTOMER-PR
TNR1 iDCS 100 TECHNICAL MANUAL U23 U12 P1 P2 Y1 C8 C26 RLY3 C7 U5 C19 T1 C33 U21 RLY1 C25 U4 RLY2 C7 T2 U6 B4 B5 U20 C32 B3 B3 C34 U11 B4 B5 U20 C32 C34 U19 U31 D7 U19 U31 D7 B2 U15 DSS1 U18 B2 U15 DSS1 U18 Y2 C27 Y2 C27 U11 U29 C29 U11 U29 C29 BAT1 U28 D1 U27 P7 D1 U27 P7 U11 U26 U26 U17 U17 MISC U4 U18 U30 U3 U9 U3 U9 BAR CODE U2 U8 U14 U25 BAR CODE U13 Y1 C8 U5 C19 T1 C33 U21 RLY1 C25 U4 RLY2 U7 U23 U12 P1 P2 C26 RLY
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 7 JUNE 2002 SMISC CARD PRINTER RXD 2 2 TXD 3 3 GND 5 7 DTR 4 20 PIN CONNECTIONS FOR SMISC CARD TO PRINTER FIGURE 7–7 SMISC CARD PC COM 1 RXD 2 2 TXD 3 3 GND 5 5 DTR 4 PIN CONNECTIONS FOR SMISC CARD TO PERSONAL COMPUTER 4 9 PIN COM 2 3 OR 2 7 20 25 PIN FIGURE 7–8 SMISC CARD MODEM RXD 2 2 TXD TXD 3 3 RXD DTR 4 20 DTR GND 5 7 GND RTS 7 4 RTS CTS 8 5 CTS PIN CONNECTIONS FOR SMISC CARD TO MODEM FIGURE 7–9 HOME PAGE Table
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 7 JUNE 2002 25 PAIR CABLE WITH MALE CONNECTOR TO BASIC P2 25 PAIR CABLE WITH MALE CONNECTOR TO EXPANSION P5 PIN COLOR TERM CIRCUIT FUNCTION 26 1 W-BL BL-W 1 2 SLOT 1 TRUNK 1 C.O. TIP C.O. RING 27 2 W-O O-W 3 4 SLOT 1 TRUNK 2 C.O. TIP C.O. RING 28 3 W-GN GN-W 5 6 SLOT 1 TRUNK 3 C.O. TIP C.O.
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 7 JUNE 2002 25 PAIR CABLE TO KSU CIRCUIT 1 2 FUNCTION SLT TIP SLT RING SLT TIP SLT RING ONE PAIR TWISTED SHEATHED STATION CABLE 24 OR 26 AWG R G BK Y W BL 1 2 3 4 5 6 CONNECT TO ANY CIRCUIT ON 2 SLI CARD, S8SLI CARD OR 2 X 4 SLI CARD.
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 7 JUNE 2002 RESERVE POWER BATTERY CONNECTOR POWER SUPPLY BLACK RED CONNECT TO EITHER A OR B + – 12V + – 12V + – + 12V – + 12V + – + 6V 6V + – – + + – 6V 6V + – – – 6V 6V + – OPTION A + 6V – + 6V – OPTION B BATTERIES SHOULD BE PLACED WITHIN THREE FEET OF KSU RESERVE POWER BATTERY CONNECTIONS FIGURE 7–12 HOME PAGE Table of Contents
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 8 JUNE 2002 PART 8. INSTALLING KEYSET DAUGHTERBOARDS 8.1 KDB DLI Before performing this procedure, the line cord must be unplugged from the keyset. The base wedge should then be removed, the keyset should be placed face down on a soft surface and the four base retaining screws removed (see Figure 8–1). The base should now be separated from the keyset and the keyset top half set aside.
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 8 JUNE 2002 HANDSET TEL RETAINING SCREWS RETAINING SCREWS KEYSET BASE FIGURE 8–1 HOME PAGE Table of Contents
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 8 JUNE 2002 MOUNTING SCREWS RIBBON CABLE CONNECTOR INSTALLING KDB DLI DAUGHTERBOARD FIGURE 8–2 HOME PAGE Table of Contents
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 8 JUNE 2002 KEYSET DAUGHTERBOARD OUTPUT JACK HANDSET TEL OUTPUT JACK FIGURE 8–3 HOME PAGE Table of Contents
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 8 JUNE 2002 HOOK P1 P2 P7 SP MIC PLUG RIBBON CABLE FROM DAUGHTERBOARD INTO RIBBON CABLE CONNECTOR P7 CONNECTING KEYSET DAUGHTERBOARD TO KEYSET PCB FIGURE 8–4 HOME PAGE Table of Contents
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 8 JUNE 2002 RIBBON CABLE CONNECTOR MOUNTING SCREWS INSTALLING KDB SLI DAUGHTERBOARD FIGURE 8–5 HOME PAGE Table of Contents
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 8 JUNE 2002 LINE CORD SCROLL VOL OUTPUT JACK SPK 1 2 ABC 3 DEF 4 GHI 5 JKL 6 MNO 7 PRS 8 TUV 9 WXY HOLD TRSF TEL 0OPER HANDSET ANS/ RLS SECOND KEYSET FIRST KEYSET CONNECTING A KEYSET TO A KDB-DLI FIGURE 8–6 LINE CORD OUTPUT JACK TEL HANDSET SINGLE LINE TELEPHONE FIRST KEYSET CONNECTING A SINGLE LINE TELEPHONE TO A KDB-SLI FIGURE 8–7 HOME PAGE Table of Contents
MDF MULTI-PAIR STATION CABLE G G G R R R Y Y Y BK BK BK BL W BL W BL W 6 5 4 3 2 1 6 5 4 3 2 1 6 5 4 3 2 CONNECTING A STATION DEVICE TO A KDB VIA THE MAIN DISTRIBUTION FRAME 1 VOL SPK ANS/ RLS TRSF HOLD 6 MNO 0OPER 9 WXY 3 DEF 5 JKL 8 TUV 2 ABC 4 GHI 7 PRS 1 SCROLL CONNECT TO KEYSET OR SLT DEPENDING ON KDB TYPE TEL HANDSET CROSS-CONNECT SECOND PAIR TO DIFFERENT STATION CABLE iDCS 100 TECHNICAL MANUAL INSTALLATION PART 8 JUNE 2002 FIGURE 8–8 HOME PAGE Table of Contents
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 9 JUNE 2002 PART 9. CHANGING SOFTWARE 9.1 REPLACING THE EPROMS The first thing you should do before proceeding is to discharge any static electricity you may have gathered by touching a ground point such as the cover of the KSU Power Supply. When you have done this then check the iDCS MEM3 card and ensure that the memory switch is in the ON position. Next turn the KSU off and disconnect the backup batteries, if equipped, from the power supply.
iDCS 100 TECHNICAL MANUAL ON OFF INSTALLATION PART 3 JUNE 2002 RESET U14 U15 U6 U5 U4 U3 LED1 SW2 D3 D2 D1 U7 C10 U10 ODD2 U12 EVN2 ODD1 EVN1 U2 U11 U9 U13 BAR CODE P1 C14 BT1 iDCS MEM3 CARD FIGURE 9–1 HOME PAGE Table of Contents
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 10 JUNE 2002 PART 10. INSTALLING CALLER ID 10.1 GENERAL INFORMATION In order to install Caller ID on a iDCS 100, you must have the following pieces of iDCS 100 equipment available: A personal computer with the latest version of PCMMC for the iDCS 100 is recommended. This will allow the original system database to be saved in the case of an upgrade to an existing system. The iDCS 100 is compatible with both types of Caller ID as defined by BELLCORE.
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 10 JUNE 2002 ! MMC 119 CID DISPLAY This MMC is used by the end user to determine which piece of Caller ID data is displayed when a call rings at the user’s station. ! MMC 501 SYSTEM TIMERS This MMC has two new timers related to Caller ID. The only timer that may need adjustment is the CID DISPLAY TIME. This is the length of time that CID data will be displayed after the CID key is pressed.
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 11 JUNE 2002 PART 11. ADDING CARDS TO AN EXISTING SYSTEM 11.1 ADDING AN SMISC CARD 1. 2. 3. 4. 5. 6. Check the battery switch on the MEM3 or MEM4 card and make sure it is ON. Turn off power to the system and unplug the power cord. Insert the SMISC2 card into the slot labeled MISC. Restore power to the system. Open system programming and use MMC 806 to initialize the card. Use MMC 724 to assign directory numbers to the ports on the card.
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 11 JUNE 2002 ITEM PORT NUMBER SLI PORT 1 019 SLI PORT 2 020 11.3 ADDING AN S3TRK CARD 1. 2. 3. 4. 5. 6. Check the battery switch on the MEM3 or MEM4 card and make sure it is ON. Turn off power to the system and unplug the power cord. Insert the S3 TRK card into an empty universal slot. Restore power to the system. Open system programming and use MMC 806 to initialize the card. Use MMC 724 to assign directory numbers to the ports on the card.
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 11 JUNE 2002 11.7 ADDING A 2 X 4 CARD 1. 2. 3. 4. 5. 6. Check the battery switch on the MEM3 or MEM4 card and make sure it is ON. Turn off power to the system and unplug the power cord. Insert the 2 X 4 card into an empty universal slot. Restore power to the system. Open system programming and use MMC 806 to initialize the card. Use MMC 724 to assign directory numbers to the ports on the card.
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 11 JUNE 2002 11.9 ADDING AN SPLL DAUGHTER BOARD 1. Check the battery switch on the MEM3 or MEM4 card and make sure it is on. 2. Turn off power to the system and unplug the power cord. 3. Install the SPLL card onto its connectors in the bottom left hand corner of the KSU motherboard (see Figure 11–2). 4. Restore power to the system. NOTE: The SPLL DAUGHTER BOARD is required in system to support BRI operation. 11.10 ADDING A MODEM CARD 1.
UNIVERSAL SLOT 3 UNIVERSAL SLOT 1 UNIVERSAL SLOT 2 MISC SLOT MEM SLOT INSTALLATION PART 11 JUNE 2002 2 SLI SLOT iDCS 100 TECHNICAL MANUAL SPLL DAUGHTER BOARD U10 U9 U8 U15 L3 D2 L2 Y1 C2 C13 C3 L1 U13 U7 U11 B3 U16 U6 U14 U3 U5 B5 U4 U1 PLL U2 SPLL INSTALLATION ON KSU MOTHERBOARD FIGURE 11–2 HOME PAGE Table of Contents
TNR3 TNR2 TNR1 P2 U23 U12 P1 C26 RLY3 C8 Y1 U5 RLY2 C33 U21 T1 RLY1 C25 U4 C19 C7 T2 C32 B3 C34 B5 U20 U11 B4 U31 D7 U19 DSS1 U18 U15 B2 C27 Y2 C29 U29 U11 P7 U27 D1 U2 U26 C13 MODEM CARD INSTALLATION ON SMISC CARD U1 U11 MISC C15 C18 U10 C6 C4 C1 C2 U14 MODEM CARD U3 X1 U17 L1 U4 U9 U3 U5 U6 MODEM BAR CODE BAR CODE iDCS 100 TECHNICAL MANUAL INSTALLATION PART 11 FEBRUARY 2002 MODEM CARD SMISC 1 OR 2 CARD FIGURE 11–3 HOME PAGE Table of C
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 12 JUNE 2002 PART 12. INSTALLING A SVMi-8 CARD 12.1 SYSTEM SIZE WITH SVMi-8 For the purpose of assigning system resources the SVMi-8 card consumes the equivalent system capacity of 8 keysets. This means that when a SVMi-8 card is installed in the iDCS 100 the system can now support a maximum of 32 (or 48 with SPSU2) station devices. This capacity includes keysets, any device connected to a keyset port, SLTs and keyset daughter boards. 12.
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 12 JUNE 2002 Power Supply. When you have done this then check the MEM3 or MEM4 card and ensure that the memory switch is in the ON position. Next turn the KSU off and remove the SVMi-8 card by gently pulling on the card. Lay the SVMi-8 card face up on a nonconductive surface. Position the second VPM over the card connector on the SVMi-8 base board and gently apply pressure until the card seats. The SVMi-8 card can now be reinstalled in the KSU. 12.
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 13 JUNE 2002 PART 13. INSTALLING A SVMi-4 CARD 13.1 SYSTEM SIZE WITH A SVMi-4 CARD INSTALLED For the purposes of assigning system resources the SVMi-4 card consumes the equivalent system capacity of 4 keysets. This means that when a SVMi-4 card is installed in the iDCS 100 the system can now support a maximum of 52 station devices. This capacity includes keysets, any device connected to a keyset port, SLTs and keyset daughter boards. 13.
iDCS 100 TECHNICAL MANUAL INSTALLATION PART 13 JUNE 2002 U32 Upgrade Key Socket U34 Z2 U33 U36 U14 U15 J1 U1 SIO Port BAR CODE J5 U41 U29 U28 U19 U23 U9 U8 S1 U30 J4 Reset Button U27 U25 U10 U26 U21 U24 Compact Flash Socket SVMi-4 CARD FIGURE 13–1 HOME PAGE Table of Contents
