HW-D7000 Blu-ray™ AV Receiver System user manual imagine the possibilities Thank you for purchasing this Samsung product. To receive more complete service, please register your product at www.samsung.com/register HW-D7000_XAA_0321.
Safety Information Safety Warnings TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER(OR BACK). NO USER-SERVICEABLE PARTS ARE INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN The lighting flash and Arrowhead within Triangle Is awarning sign alerting you of dangerous voltage Inside the product. CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE.
Important Safety Instructions Read these operating instructions carefully before using the unit. Follow all the safety instructions listed below. Keep these operating instructions handy for future reference. 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.
Safety Information Precautions • Ensure that the AC power supply in your house complies with specifications listed on the identification sticker located on the back of your product. • Install your product horizontally, on a suitable base (furniture), with enough space around it for ventilation (7.5~10cm / 20~25 inches). • Do not place the product on amplifiers or other equipment which may become hot. Make sure the ventilation slots are not covered. • Do not stack anything on top of the product.
Cautions on Handling and Storing Discs Small scratches on the disc may reduce sound and picture quality or cause skipping. Be especially careful not to scratch discs when handling them. Holding discs • Do not touch the playback side of the disc. • Hold the disc by the edges so that fingerprints will not get on the surface. • Do not stick paper or tape on the disc. Disc Storage • Do not keep in direct sunlight • Keep in a cool ventilated area • Keep in a clean protection jacket and store vertically.
Contents 2 3 4 5 5 5 Safety Warnings Important Safety Instructions Precautions Cautions on Handling and Storing Discs License Copyright GETTING STARTED 8 10 11 15 16 16 18 19 Key features of your new Blu-ray Receiver Icons that will be used in manual Disc Types and Characteristics Accessories Description Front Panel Rear Panel Remote Control CONNECTIONS 21 22 23 24 25 26 27 28 29 30 31 31 32 Speaker Positioning Attaching the Toroidal Ferrite Core to the Power Cord of the Main Unit Connecting the Spea
47 47 50 50 51 51 51 51 51 51 52 52 52 52 52 52 52 52 52 53 53 53 55 Network Network Settings Network Status BD-LIVE Internet Connection System Initial Settings Anynet+ (HDMI-CEC) BD Data Management Input Selection Time Zone DivX® Video On Demand Reset Language Security BD Parental Rating DVD Parental Rating Change Password General Front Display Network Remote Control Support Software Upgrade Contact Samsung BASIC FUNCTIONS 56 56 57 57 58 58 59 61 63 65 66 67 68 68 69 Playing a Disc Using the Disc menu
Getting Started Key features of your new Blu-ray Receiver Product Features Digital Receiver This product is a pure digital receiver that performs digital signal processing to minimize signal distortion and loss. 3D This product can play 3D contents through an HDMI cable. To implement the 3D effect, connect a 3D TV to the product using an HDMI cable, and play the 3D content while wearing 3D vision glasses.
01 Adds a surround back channel for more spacious sound compared to regular 5.1 channel Dolby Digital. Dolby Pro Logic llx Dolby Pro Logic IIx is a new technology that provides discrete 7.1 channels out of 2 channel or multi channel sources.It also provides Music,Movie and Game modes. Dolby Pro Logic IIx is an improved surround system that is optimized to a 7.1 CH multimedia system, enabling you to maximize your entertainment experience.
Getting Started Icons that will be used in manual Make sure you understand the following terms before reading the rest of the user manual. Term Logo Icon h z Z BD-ROM BD-RE/-R DVD-VIDEO Definition Indicates a function available on a BD-ROM. Indicates a function available on a BD-RE/-R disc recorded in the BD-RE format. Indicates a function available on a DVD-VIDEO.
01 Logos of Discs that can be played Blu-ray Disc Compatibility Blu-ray is a new and evolving format. Accordingly, disc compatibility issues are possible. Not all discs are compatible and not every disc will play back. For additional information, refer to the Disc Types and Characteristics section of this Manual. Blu-ray Disc 3D Blu-ray Disc Dolby Digital Plus NTSC broadcast system in U.S.
Getting Started Region Code BD-RE/-R Both the product and the discs are coded by region. These regional codes must match for the product to play the disc.If the codes do not match, the disc will not play. Blu-ray RE/-R discs can be recorded and played back. This product can play back a BD-RE/-R disc recorded by other compatible Blu-ray disc recorders. DVD-VIDEO Disc Type Blu-ray Region Code Area A North America, Central America, South America, Korea, Japan, Taiwan, Hong Kong and South East Asia.
01 Using JPEG discs • The home theater can play back D-R/-RW, DVD-RW/-R discs recorded in the UDF or JOLIET format. • Only JPEG files with the ".jpg", ".JPG", ".jpeg" or "JPEG" extension can be displayed. • Progressive JPEG is supported. Getting Started Disc Format DVD-RW/-R (V) • This format is used for recording data on DVD-RW or DVD-R discs. This product can play DVD-RW or DVD-R discs if they have been finalized.
Getting Started File Extension Container *.vro VRO VOB Video Codec Audio Codec Resolution MPEG2 AC3 MPEG LPCM 1920x1080 AC3 MPEG LPCM AAC 352x288 MPEG1 MPEG1 *.mpg *.mpeg MPEG2 PS H.264 1920x1080 1920x1080 AC3 AAC MP3 DD+ HE-AAC MPEG2 *.ts *.tp *.trp 352x288 H.264 TS VC1 1920x1080 1920x1080 1920x1080 Restrictions • • • • • Some of the Codecs listed above will not play if there is a problem with the contents.
01 Supported devices: USB storage media, MP3 player, digital camera, USB card reader 1) The product does not support folder or file names longer than 125 characters. 2) A subtitle file bigger than 300 KB may not be properly displayed. 3) Some USB/digital camera devices may not be compatible with the product. 4) The praoduct supports the FAT16 and FAT32 file systems. 5) Photo (JPEG), music (MP3,) and video files must have Korean or English file names. Otherwise, the files will not play.
Getting Started Description Front Panel 1 2 3 4 5 6 7 8 INPUT SELECT MASTER VOLUME ASC MIC SELECT TONE CONTROL Smart HUB S.Direct vTuner 10 9 AV SYNC TUNING MODE MEMORY MENU RETURN AUDIO ASSIGN AUDIO EFFECT VIDEO AUDIO PHONES 3D SOUND AUX 1 IN 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 1 INPUT SELECT Used to select a source. BD/DVD SAT GAME AUX1 AUX2 CD R-IPOD FM TV 2 3 4 5 6 REMOTE CONTROL SENSOR Detects signals from the remote control.
01 TONE CONTROL BUTTON Used to set the bass, treble level and tone to on/off. SMART HUB BUTTON Display the Smart Hub service screen. 13 S.DIRECT BUTTON Used to select the S.DIRECT mode. (Output the original signal as it is without applying the sound field effect or any other sound effect. 14 15 16 vTuner BUTTON Used to select the vTuner. AV SYNC BUTTON Used to set the Audio Delay. TUNING MODE BUTTON Used to select the Manual or Preset mode for FM radio.
Getting Started Rear Panel 1 2 3 4 LAN iPod 5 6 HDMI OUT HDMI IN ARC (MONITOR) VIDEO IN SAT GAME HDMI 1 (SAT) VIDEO OUT TV HDMI 2 (GAME) HDMI 3 (AUX1) HDMI 4 (AUX2) SPEAKER IMPEDANCE : 4~8 COMPONENT IN/OUT 1 (SAT) MONITOR FRONT 2 (GAME) SURROUND SURROUND BACK /FRONT HEIGHT CENTER SURROUND BACK SURROUND /FRONT HEIGHT FRONT Y SUBWOOFER OUT PB/CB PR/CR SAT FM ANT 7 GAME TV CD AUDIO IN 8 IN 9 OUT 10 OPTICAL 1 OPTICAL 2 OPTICAL 3 COAXIAL (SAT) (GAME) (TV) (CD) 11 SPEAK
01 Getting Started Remote Control Tour of the Remote Control INPUT SELECT TV SOURCE POWER Turn the product on and off. To change to TV mode, press the TV button. To change to receiver, press the BD-RX button. To eject the disc. BD-RX TV SHIFT 1 Press numeric buttons to operate options. 2 4 3 5 6 SLEEP TONE 9 After pressing the SHIFT button, 7 8 Press to select S.DIRECT mode. S.DIRECT AUDIO ASSIGN FULL SCREEN 0 or Press to see the full screen on a TV.
Getting Started Installing batteries in the Remote Control * Battery size: AAA TV Brand Code List Brand Code Brand Code Admiral (M.
02 Connections Speaker Positioning Connections This section involves various methods of connecting the receiver to other external components. Before moving or installing the product, be sure to turn off the power and disconnect the power cord. There are two methods for positioning the speakers. FHL FHR 6.6~9.8 feet (2~3m) 6.6~9.
Connections Surround Back Speakers SBL SBR If you are using two surround center speakers, place them behind the listening position. Place the surround back speaker about 2.3-3.3 feet (70 cm to 1 m). Front Height Speakers FHL FHR (Using Dolby Pro Logic IIz) When using Dolby Pro Logic IIz, place the Surround Back Speakers on the FHL, FHR position above the front L and front R speakers at least 3.3 feet(1 m) above each one.
02 Connecting the Speakers Connections Connecting Speaker Wire 1. Loosen the knob by turning counterclockwise. 2. Insert the bare part of the wire into the hole in the side of each terminal. 3. Tighten the knob by turning clockwise to secure the wire.
Connections Connecting the Bi-AMP Speaker Connect the tweeter (high range) port and woofer (low range) to the front port and surround back speaker port respectively as appropriate. Then, you can use the bi-amplifi cation feature that supports enriched high range and base tones.
02 HDMI is a digital standard interface for connection to such devices as a TV, projector, DVD player, Blu-ray player, set-top box and more. Connections Connecting External Devices/your TV via HDMI HDMI removes any loss of signal from analog conversion, enabling you to enjoy video and audio sound quality as it was originally created in the digital source.
Connections Connecting to your TV LAN HDMI OUT iPod HDMI IN ARC ARC (MONITOR) (M MONITOR OR) VIDEO IN SAT GAME HDMI 1 (SAT) VIDEO OUT TV HDMI 2 (GAME) HDMI 3 (AUX1) HDMI 4 (AUX2) SPEAKER IMPEDANCE : 4~8 COMPONENT IN/OUT 1 (SAT) MONITOR FRONT 2 (GAME) SURROUND SURROUND BACK /FRONT HEIGHT CENTER SURROUND BACK SURROUND /FRONT HEIGHT FRONT Y SUBWOOFER OUT PB/CB PR/CR SAT FM ANT GAME TV AUDIO IN CD IN OUT OPTICAL 1 OPTICAL 2 OPTICAL 3 COAXIAL (SAT) (GAME) (TV) (CD) SPEAKERS OUT
02 Connections Connecting a Cable, Satellite or Set-top Box COMPONENT IN VIDEO IN or LAN HDMI OUT iPod HDMI IN A ARC RC (M MONITOR OR) (MONITOR) VIDEO IN SAT GAME HDMI 1 (SAT) VIDEO OUT TV (not supplied) HDMI 2 (GAME) HDMI 3 (AUX1) HDMI 4 (AUX2) SPEAKER IMPEDANCE : 4~8 COMPONENT IN/OUT 1 (SAT) MONITOR FRONT 2 (GAME) SURROUND SURROUND BACK /FRONT HEIGHT CENTER SURROUND BACK SURROUND /FRONT HEIGHT FRONT Y SUBWOOFER OUT PB/CB PR/CR SAT GAME TV AUDIO IN FM ANT CD IN OUT OPT
Connections Connecting a Game Console COMPONENT IN VIDEO IN (not supplied) or LAN HDMI OUT iPod HDMI IN A ARC RC (M MONITOR OR) (MONITOR) VIDEO IN SAT GAME HDMI 1 (SAT) VIDEO OUT TV HDMI 2 (GAME) HDMI 3 (AUX1) HDMI 4 (AUX2) SPEAKER IMPEDANCE : 4~8 COMPONENT IN/OUT 1 (SAT) MONITOR FRONT 2 (GAME) SURROUND SURROUND BACK /FRONT HEIGHT CENTER SURROUND BACK SURROUND /FRONT HEIGHT FRONT Y SUBWOOFER OUT PB/CB PR/CR SAT GAME TV AUDIO IN FM ANT CD IN OUT OPTICAL 1 OPTICAL 2 OPTIC
02 Connections Connecting a CD Player CD Player AUDIO OUT (not supplied) LAN HDMI IN A ARC RC (MONITOR) (M MONITOR OR) VIDEO IN SAT GAME HDMI 1 (SAT) VIDEO OUT TV (not supplied) or HDMI OUT iPod COAXIAL OUT HDMI 2 (GAME) HDMI 3 (AUX1) HDMI 4 (AUX2) SPEAKER IMPEDANCE : 4~8 COMPONENT IN/OUT 1 (SAT) MONITOR M ON TOR FRONT 2 (GAME) SURROUND SURROUND BACK /FRONT HEIGHT CENTER SURROUND BACK SURROUND /FRONT HEIGHT FRONT Y SUBWOOFER OUT PB/CB PR/CR SAT FM ANT GAME TV AUDIO IN CD
Connections Video Conversion Flow According to the Connected Port As shown in the illustration, if the unit’s HDMI Out is connected to a TV or monitor, the analog video source (composite or component) from the video device is processed for up-conversion automatically for HDMI output. If connected to a TV or monitor through Composite or Component ports, corresponding analog signal will be output respectively, without any conversion.
02 1. Connect the FM antenna supplied to the FM ANTENNA terminal as a temporary measure. 2. Slowly move the antenna wire around until you find a location where reception is good, then fasten it to a wall or other rigid surface.
Connections Connecting to a Network You can connect this product to a network and use network based services such Smart Hub and BDLIVE (See pages 70~79), as well as receive software upgrades through the network connection. We recommend using a wireless router or IP router for the connection. For more information on router connection, refer to the user manual of the router or contact the router manufacturer for technical assistance. Cable Network 1.
02 You can connect the Receiver to your network through a wireless IP sharer (router). To set the network configuration options. see page 47. Connections Wireless Network Broadband service Wireless IP sharer INPUT SELECT MASTER VOLUME PC Networking with PC for AllShare function (See page 79) ✎ NOTE To use a wireless network, your product must be connected to a wireless IP sharer (router).
Setup Initial Settings 1. Turn on your TV after connecting the product. When you connect and turn on the product to a TV for the first time, the Initial Settings screen appears. • Home Menu My Contents Videos Photos Music Function My Devices Internet Settings Initial Settings | On-Screen Language Select a language for the on-screen displays.
03 DISC MENU MENU 3. Press the ▲▼ buttons to select the desired submenu, and then press the ENTER button. TITLE MENU POPUP 1 TOOLS Setup 2. Press the ◄► buttons to select Settings, and then press the ENTER button. Accessing the Settings Menu INFO 4. Press the ▲▼ buttons to select the desired item, and then press the ENTER button. 3 5. Press the EXIT button to exit the menu.
Setup Depending on the content and the position of Display You can configure various display options such as the TV Aspect Ratio, Resolution, etc. 3D Settings Screen Size Select whether to play a Blu-ray Disc with 3D contents in 3D Mode.
03 Depending on the type of television you have, you may want to adjust the screen size setting. • 16:9 Original : Select when you connect the product to a 16:9 TV screen. The product will display all content in its original aspect ratio. Content formatted in 4:3 will be displayed with black bars on the left and right. • 16:9 Full : Select when you connect the product to a 16:9 TV screen. All content will fill the full screen. Content formatted in 4:3 will be stretched.
Setup Resolution according to the output mode • Blu-ray Disc/E-contents/Digital Contents playback HDMI / connected HDMI / not connected HDMI Mode Output Component Mode Blu-ray Disc E-contents/ Digital contents Component/ VIDEO Mode Blu-ray Disc E-contents/ Digital contents VIDEO Mode BD Wise Resolution of Blu-ray Disc 1080p@60F 480i - - - Auto Max. Resolution of TV input Max.
03 changed the resolution, remove all discs, and then press and hold the STOP () button on the front of the product for more than 5 seconds. All settings are restored to the factory default. Follow the steps on the previous page to access each mode and select the Display Setup that your TV will support. When the factory default settings are restored, all stored user BD data is deleted. The Blu-ray Disc must have the 24 frame feature for the product to use the Movie Frame (24Fs) mode.
Setup • Large : Select when using large speakers. You can listen to full range sound. • Small : Select this when using small speakers. • None : Select when no speaker is used. • On (subwoofer) : Select when using the subwoofer speaker. • Off (subwoofer) : Select when not using the subwoofer speaker. Audio Speaker Settings Settings Speaker Settings Display Audio Size Network Level System Distance Language 7.1 CH Connection : Surround Back Security Test Tone | ✎ NOTE You can also use the ,,.
03 If you cannot place the speakers at equal distances from the listening position, you can adjust the delay time of the audio signals from the front, center, surround, surround back and subwoofer speakers. • You can set the Speaker Distance between 1ft (0.3m) and 30ft (9.0m). Settings Distance Display Audio Network System Language Security General Support Front L ◄ Front R : Center : Surround L : Surround R : Surround Back L : Surround Back R : Subwoofer : Test Tone : 10(ft) 3.0(m) | 10(ft) 3.
Setup Musical Room Calibration By setting the Musical Room Calibration (MRC) function just once when you relocate or install the product, you can have the product automatically recognize the distance between speakers, levels between channels, and frequency characteristics to create a 7.1-channel sound field optimized for your environment. ASC MIC VIDEO AUDIO ✎ NOTE Running the Musical Room Calibration function takes about 3 minutes.
03 Setup Surround Set surround sound effect-related functions.
Setup ✎ NOTE Channel status displays are dependent on the speaker configuration. SFE mode works with 2-ch signals. If Dolby Pro Logic IIz is set to On, Dolby true HD, Dolby plus, DTS-HD Master Audio, SFE and NE0:6 will be output 5.1 channel. • Off : Dolby Digital Surround EX / DTS ES decoder will not be used for playback. • On : Dolby Digital or DTS signal will be played in 6.1 / 7.1 channel using Dolby Digital Surround EX / DTS ES decoder.
03 Setup Dual Mono Digital Output Dual mono programs have two independent mono channels. You can use this function when dual mono programs are played. When you use this function, select audio channels CH1, CH2 or both Channel. You set the Digital Output to match the capabilities of the AV device you’ve connected to the product : • PCM : Choose if you have connected an HDMI supported AV device.
Setup Digital Output Selection Setup PCM Bitstream (Unprocessed) Bitstream (Re-encoded DTS) Bitstream (Re-encoded Dolby D) HDMI supported HDMI supported HDMI supported HDMI supported AV device AV device AV device AV device Connection PCM Up to 7.1ch PCM DTS re-encoded Re-encoded Dolby Digital * Dolby Digital Up to 7.1ch Dolby Digital DTS re-encoded Re-encoded Dolby Digital * Dolby Digital Plus Up to 7.
03 Setup Dynamic Range Control Network Settings You can listen at low volumes, but still hear dialog clearly. This is only active if your product detects a Dolby Digital signal. • Auto : The Dynamic Range Control will be set automatically based on the information provided by the Dolby TrueHD Soundtrack. • Minimum : This slightly compresses the dynamic range. • Standard : This is standard setting for regulate home use.
Setup To view your Network Settings values on most Windows computers, follow these steps: 1. Right click the Network icon on the bottom right of the Windows desktop. 11. Press the ENTER button to select OK. The Network Status screen appears. The product connects to the network after the network connection is verified. 2. In the pop-up menu, click Status. Wireless Network 3. On the dialog that appears, click the Support tab.
03 Settings Display Audio Network Settings Enter security key. 0 entered To enter the Network settings into your product, follow these steps: Setup 4. On the Security screen, enter your network’s Pass Phrase. Enter numbers directly using your remote control. To select a letter, press the ▲▼◄► buttons to move the cursor, then press the ENTER button. 1. Follow Steps 1 through 5 in the ‘Setting Up the Wireless Network Connection - Auto’ procedure. 2.
Setup WPS(PBC) 2. Press the ENTER button. The easiest way to set up the wireless network connection is using the WPS(PBC) function or the One Foot Connection function. If your wireless router has a WPS(PBC) button, follow these steps: 1. Press the ▲▼ buttons to select WPS(PBC). Settings Network Settings Display Select a network connection type. Audio Network 3. Place the Samsung Wireless Router within 25 cm (10 inches) of your product to connect. 4. Wait until the connection is automatically established.
03 Initial Settings By using the Initial Settings function, you can set the language, Network Settings, etc. For more information about the Initial Settings function, refer to the Initial Settings section of this user manual. (See page 34) Anynet+ (HDMI-CEC) Anynet+ is a convenient function that offers linked operations with other Samsung products that have the Anynet+ feature. To operate this function, connect this product to a Samsung TV with an HDMI cable.
Setup DivX® Video On Demand Shows the registration code authorized for the product. If you connect to the DivX web site and register using that code, you can download the VOD registration file. If you activate the VOD registration using My Contents, the registration is completed. ✎ NOTE For more information about DivX(R) VOD, visit "http://vod.divx.com". Reset All settings will revert to the default except for the network and Smart Hub settings. You need enter the password for this function.
03 The four methods are explained below. The Network Remote Control function lets you control your Blu-ray Home Theater from a remote device such as a smart phone through a wireless connection to your local area network. By Internet To use the Network Remote Control function, follow these steps: 1. Select On in the Network Remote Control menu. 2. Install the Samsung network remote control application to control your product on your compatible portable device. 3.
Setup By USB To upgrade by USB, follow these steps: 1. Visit www.samsung.com/bluraysupport 2. Download the latest USB software upgrade zip archive to your computer. 3. Unzip the zip archive to your computer. You should have a single folder with the same name as the zip file. 4. Copy the folder to a USB flash drive. 5. Make sure the disc tray is empty, and then insert the USB flash drive into the USB port of the product. 6. In the product’s menu, go to Settings > Support > Software Upgrade. 7. Select By USB.
03 Setup Download in Standby Mode You can set the Download in Standby Mode function so that the product downloads new upgrade software when it is in Standby mode. In Standby mode, the product is off, but its Internet connection is active. This allows the product to download upgrade software automatically, when you are not using it. To set Download in Standby Mode, follow these steps: 1. Press the ▲▼ buttons to select Download in Standby Mode, and then press the ENTER button. 2. Select On or Off.
Basic Functions • Audio CD (CD-DA) Playing a Disc track 1 track 2 track 3 track 4 track 5 Playback 1. Insert a disc into the disc slot with the disc's label facing up. 2. Press the PLAY (►) button. folder (group) 1 file 1 file 2 Playback related buttons PLAY ( ►) Starts playback. STOP ( ) Stops playback. • If you press the button once : The stop position is memorized. • If you press the button twice : The stop position is not memorized.
04 Using the Search and Skip Functions Z 1. During playback, press the TITLE MENU button on the remote control. 2. Press the ▲▼◄ ► buttons to make the desired selection, then press the ENTER button. TITLE MENU POPUP Searching for a Desired Scene hzZyx ✎ NOTE Depending on the disc, the menu items may differ and this menu may not be available. The Title Menu will only be displayed if there are at least two titles on the disc. Using the Popup Menu h 1.
Basic Functions Slow Motion Play/Step Motion Play Repeat > Off Slow Motion Play hzZyx • In pause ( ) mode, press the SEARCH () button. If you press the SEARCH () button, the playback speed is reduced to * 1/8 * 1/4 * 1/2 • To return to normal speed playback, press the PLAY (► ) button. ✎ NOTE The product does not play sound in slow 3. To return to normal play, press the REPEAT button again. 4. Press the ▲▼ buttons to select Off, then press the ENTER button.
04 During playback, you can operate the disc menu by pressing the TOOLS button. TOOLS • TOOLS Menu Screen Tools Title Search Chapter Search Time Search Picture Settings Audio User EQ Subtitle Angle 1/2 : 1/20 : 00:00:13/01:34:37 : Normal : 1/4 ENG Multi CH : : audio modes will be also displayed if the Bluray Disc has a BONUSVIEW section. Use the ◄► button to switch between primary and secondary audio modes. The languages available depend on the languages that are encoded on the disc.
Basic Functions Caption Function x • You must have some experience with video extraction and editing in order to use this feature properly. • To use the caption function, save the caption file (*.smi) with the same file name as that of the DivX media file (*.avi) within the same folder. Example. Root Samsung_007CD1.avi Samsung_007CD1.smi • You can use up to 60 alphanumeric characters or 30 East Asian characters (2 byte characters such as Korean and Chinese) for the file name.
04 7 ENTER button : Plays the selected track. 8 ► button : During playback, moves to the next page in the Music List or moves to the next track in the Playlist. ◄ button : During playback, moves to the previous page in the Music List or moves to the previous track in the Playlist. 3 9 STOP button : Stops a track. 0 $ button : Plays the next track. ! # button : Plays the previous track.
Basic Functions Playing an Audio CD (CD-DA)/MP3 Repeat an Audio CD (CD-DA)/MP3 1. Insert an Audio CD (CD-DA) or an MP3 Disc into the disc slot. • For an Audio CD (CD-DA), the first track will be played automatically. • For an MP3 disc, press the ◄► buttons to select Music, then press the ENTER button. 1. During the Playlist playback, press the REPEAT button. Audio CD (CD-DA)/MP3 Screen Elements 1 2 3 REPEAT 2. Select the desired play mode by pressing the REPEAT button repeatedly.
04 Sound Mode 1/2 Page Selected Items : 3 TRACK 001 TRACK 002 00:43 03:56 TRACK 003 TRACK 004 04:41 04:02 TRACK 005 TRACK 006 03:43 03:40 TRACK 007 TRACK 008 04:06 03:52 Close Edit Mode ( ) Page Tools SFE (Sound Field Effect) MODE You can set the SFE mode best suited for the type of music you are listening to. " Select ' Return 5. When done, press the TOOLS button. 6. To play the selected track(s), select Play Selected in the Tools menu, and then press ENTER.
Basic Functions Setting the speakers with DPL IIx The models below support audio sync 1. Set the 7.1CH Connection settings to "Surround Back". (For further details, refer to page 41.) settings. Press iPod SYNC on the remote control to change audio delay. Supported Models : classic/3G nano/4G nano/120GB classic/160GB Classic/5G nano PL II button of the remote 2. Press the control until the desired setting is displayed.
04 You can listen to sound in 2 channel analog , Dolby Digital or DTS using this unit. Playing back a Picture G AUDIO ASSIGN 0 Viewing Photo Files Each time you press this button, the input mode changes as follows: For SAT function SAT HDMI1 SAT OPTIC1 SAT ANALOG For GAME function GAME HDMI2 GAME OPTIC2 GAME ANALOG For TV function TV OPTIC3(TV ARC) TV ANALOG Basic Functions AUDIO ASSIGN 1. Connect a USB memory that contains JPEG files or insert a disc that contains JPEG files. 2.
Basic Functions • Background Music Setting : Select to set the background music. • Zoom : Select to enlarge the current picture. (Enlarge up to 4 times) • Rotate : Select to rotate the picture. (Rotate the picture either clockwise or counter clockwise.) • Picture Settings : Select to adjust the picture quality. • Information : Shows the picture information including the name and size, etc.
04 Using buttons on the Remote Control 1. Press the INPUT SELECT on the remote control to select FM. 2. Tune in to the desired station. • Preset Tuning 1 : You must first add a desired frequency as a preset. Press the STOP () button to select PRESET and then press the ) button to select the preset TUNING/CH ( station. • Manual Tuning : Press the STOP () button to select MANUAL and then press the TUNING/ CH ( ) button to tune in to a lower or higher frequency.
Basic Functions Playing Music Connecting an iPod/iPhone Using the USB Cable If the Receiver is connected to an iPod/iPhone using the provided USB cable, you can play music in iPod/iPhone through the Receiver. My Contents Videos Connected Device Photos iPod MASTER VOLUME ASC MIC MENU RETURN AUDIO ASSIGN AUDIO EFFECT VIDEO AUDIO Function PHONES 3D SOUND Music My Devices Internet Settings " Enter ' Return AUX 1 IN d WPS(PBC) 1.
04 ✎ NOTE You must have the VIDEO output (Composite) connected to your TV to view iPod video. If you want to play iPod video via VIDEO output, set Anynet+ (HDMI-CEC) to off. No screen but the playback screen will appear on the TV. View other iPod screens on the iPod player. If the connected iPod does not support video playback, the "Playing video files is not supported on this iPod model." message appears when you select the Video menu.
Network Services You can enjoy various network services such as Smart Hub or BD-LIVE by connecting the product to your network. Read the following instructions before using any network service. 1. Connect the product to the network. (see pages 32~33) 2. Configure the network settings. (see pages 47~50) 3. The Smart Hub screen appears. ✎ NOTE Certain applications are available only in certain countries. 4. The Terms of Service Agreement screen appears.
05 1 2 3 4 6 Navigation Help : Displays the remote control buttons you can use to navigate in Smart Hub. • RED (A) : To log in to Smart Hub. • GREEN (B) : To sort the applications. • YELLOW (C) : To edit the applications. • BLUE (D) : To change the settings of Smart Hub. 7 My Applications : Displays your personal gallery of applications which you can add to, modify, and delete.
Network Services Using the Keypad Creating an Account Through your remote, you can use the OnScreen Keypad to enter letters, numbers, and symbols. To establish your own, exclusive, configuration of Smart Hub, create your own Smart TV Account. To create an account, follow these steps: 1. 1 2 1 2 3 .
05 When done, press the ENTER button to select OK, and then press the ENTER button again. The Create Account screen re-appears. 9. Select Confirm password, and then press the ENTER button. 10. Repeat Steps 7 and 8. 11. When the Create Account screen reappears, select Create Account, and then press the ENTER button. The Confirmation window appears. 12. Select OK, and then press the ENTER button. The Continue to Register Service window appears. 13. Select Connect Service, and then press the ENTER button.
Network Services Register Service Account Change Password If you have existing accounts with any of the providers listed by the Register Service Account function, you can associate the provider account and the provider account password with your Smart TV Account. If you associate the account, you will be able to log onto the account through Smart Hub easily, without entering your account name or password. The Change Password function lets you change your Smart Hub password.
05 4. After a few moments, Smart Hub automatically resets. The screen may go black, then Smart Hub re-appears. In a few moments, it starts the re-initialization procedure. To complete the re-initialization, go to Step 4 in Starting Smart Hub for the First Time. (See page 70) ✎ NOTE The functions in the Edit Mode Menu bar are described below. ✎ NOTE Some menu items may not appear on the screen.
Network Services Move to Folder Rename Folder The Move to Folder function lets you move a widget to a folder. To use the Move to Folder function, follow these steps: The Rename Folder function lets you rename folders. To use the Rename Folder function, follow these steps: 1. Press the YELLOW (C) button on your remote. 1. Press the YELLOW (C) button on your remote. 2. Select a widget, and then press the ENTER button. 2. Press the ▲▼◄► to select a folder, and then press the ENTER button. 3.
05 1. Press the YELLOW (C) button on your remote. 2. Press the ▲▼◄► to select a locked widget, and then press the ENTER button. 3. Press the ▲▼◄► to select Unlock, and then press the ENTER button. The Security window appears. 4. Enter the Parental Security Code (See page 52). If you have not created a Parental Security Code, enter 0000. 5. Press the ENTER button. The Lock Service Released window appears confirming the lock has been release, and then closes.
Network Services Using the Samsung Apps Screen Samsung Apps by category To use the Samsung Apps screen, follow these steps: The following categories are available: 1. Press the ◄► buttons to move to the category list on the left. 2. Press the ▲▼ to highlight a category. In a few seconds, the Samsung Apps screen displays the applications in that category. The Sort tabs appear across the top. 3. Press the ► button to move to the displayed applications or services. 4.
05 • RED (A) (Login) : To log into your Smart TV Account. • GREEN (B) (Thumbnail/List View) : To toggle applications between Thumbnail and List view. • BLUE (D) (Sort By) : To sort the applications in a category by Recommended, Most Downloaded, Most Recent, or Name. • Return : To return to the previous menu. ✎ NOTE The Internet contents services may be added or deleted by providers without notice. For instructions to use Your Video or Search Function, please visit www.samsung.
Other Information Troubleshooting Refer to the chart below when this product does not function properly. If the problem you are experiencing is not listed below or if the instructions below do not help, turn off the product, disconnect the power cord, and contact Samsung Electronics at 1-800-SAMSUNG (1-800-726-7864). Symptom Check/Remedy I cannot eject the disc. • Is the power cord plugged securely into the outlet? • Turn off the power and then turn it back on. The iPod fails to connect.
06 Other Information Symptom Check/Remedy Menu screen does not appear even when the menu function is selected. • Are you using a disc that does not contain menus? Aspect ratio cannot be changed. • You can play 16:9 BD/DVDs in 16:9 Wide mode, 4:3 Letter Box mode, or 4:3 Pan - Scan mode, but 4:3 BD/DVDs can be seen in 4:3 ratio only. Refer to the Blu-ray Disc jacket and then select the appropriate function. • The product is not working. (Example: The power goes out or a strange noise is heard.
Other Information Symptom Check/Remedy There is no sound from surround speakers. • Are the surround speakers connected properly? • Is Surround incorrectly set to NONE in the Speaker Size? • Is surround mode set to stereo? There is no sound from surround back speakers • Are the surround back speakers connected properly? • Is SBACK (Surround Back) set to NONE in the Speaker Size? • Is Surround Mode set to EX/ES? Can't select EX/ES mode.
06 Check/Remedy BD-LIVE I cannot connect to the BD-LIVE server. • Check whether the network connection is successful or not by using Network Test menu. • The memory device must have at least 1GB of free space to accommodate the BD-LIVE service. You can check the available size in BD Data Management. (See page 51) • Please check whether the BD-LIVE Internet Connection menu is set to Allow(All). • If all above fails, contact the contents provider or update the latest firmware.
Other Information Specifications General FM Tuner Power Requirements AC 120V, 60Hz Power Consumption 125 W Weight 18.74 Ibs Dimensions 16.92 (W) x 6.50 (H) x 14.19 (D) inches Operating Temperature Range +41°F to +95°F Operating Humidity Range 10 % to 75 % Signal/noise ratio 65 dB Usable sensitivity 7 dB Total harmonic distortion 0.9 % BD (Blu-ray Disc) Reading Speed : 9.
SAMSUNG Receiver LIMITED WARRANTY TO ORIGINAL PURCHASER This SAMSUNG brand product, as supplied and distributed by Samsung Electronics America, Inc.
Contact SAMSUNG WORLD WIDE If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center. Area ` North America Canada Mexico U.S.A Contact Center Web Site 1-800-SAMSUNG (726-7864) 01-800-SAMSUNG (726-7864) 1-800-SAMSUNG (726-7864) www.samsung.com www.samsung.com www.samsung.
QUESTIONS OR COMMENTS? COUNTRY CALL OR VISIT US ONLINE AT WRITE IN THE US 1-800-SAMSUNG (7267864) www.samsung.com/us Samsung Electronics America, Inc. 85 Challenger Road Ridgefield Park, NJ 07660-0511 Code No. AH68-02334S HW-D7000_XAA_0321.
