High Resolution Box Camera User Manual HCB-7000 HCB-7000PH
High Resolution Box Camera User Manual Copyright ©2017 Hanwha Techwin Co., Ltd. All rights reserved. Trademark Each of trademarks herein is registered. The name of this product and other trademarks mentioned in this manual are the registered trademark of their respective company. Restriction Copyright of this document is reserved. Under no circumstances, this document shall be reproduced, distributed or changed, partially or wholly, without formal authorization.
Before operating the camera, confirm the camera model and correct input power voltage. To help you understand this manual thoroughly, we'll introduce our model description.
safety information CAUTION RISK OF ELECTRIC SHOCK. DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit.
6. Do not place conductive objects (e.g. screwdrivers, coins, metal parts, etc.) or containers filled with water on top of the camera. doing so may cause personal injury due to fire, electric shock, or falling objects. 8. If any unusual smells or smoke come from the unit, stop using the product. in such case, immediately disconnect the power source and contact the service center. continued use in such a condition may cause fire or electric shock. 9.
safety information FCC Statement This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions : 1) This device may not cause harmful interference, and 2) This device must accept any interference received including interference that may cause undesired operation. CAUTION This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of FCC Rules.
important safety instructions Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, or other apparatus (including amplifiers) that produce heat. 9.
important safety instructions 17. Do not install the product in a place where chemical substances or oil mist exists or may be generated. As edible oils such as soybean oil may damage or warp the product, do not install the product in the kitchen or near the kitchen table. This may cause damage to the product. 18. When installing the product, be careful not to allow the surface of the product to be stained with chemical substance.
contents 10 11 12 15 Features Components and Accessories Overview Lens connection 18 18 19 20 Connecting to Monitor Connecting to Power Control via RS-485 Interface Using Coaxial Communications camera operation 21 21 Menu Configuration Menu Setup troubleshooting 32 Troubleshooting specifications 33 35 Specifications Dimension 10 18 21 32 33 English_9 ● Contents introduction
introduction Features yy High Resolution It uses 4.1-megapixel CMOS device to provide a high-definition quality of 2560x1440 resolution. yy Excellent Sensitivity The built-in high sensitivity COLOR CMOS produces a clear image. - Color : 0.16Lux (F1.2, 1/30sec) B/W : 0.009Lux (F1.2, 1/30sec) yy D-WDR If an object has a large variance between bright and dark areas, it will keep bright areas bright and make selected dark areas bright, so that the overall brightness can be maintained.
Components and Accessories Check if the following items are included in the product package.
introduction Overview Front View 1 3 2 ❶T ripod Mounting Bracket Screw Hole : `` Used to fix the camera on a bracket. The screw sizes for this hole are as follows. 1/4"-20 UNC (20 THREAD) L:4.5mm±0.2mm (ISO standard), or 0.178" (ASA standard) 2 L ens adaptor : IInstall this if you use the lens. 3A uto Iris Lens Connector : Used to connect Auto Iris Lens plug. MM `` Auto shutter adaptor, c-mount adaptor and supporting board are not provided with the camera.
Rear View ● introduction ➊ ➋ VIDEO ➌ POWER ➍ ➎ ➏ ➐ ➑ ➊ ➋ ➍ POWER ➎ ➏ ➐ ➑ VIDEO ➌ English_13
introduction 1 Function Setup switch Display the menu on the screen and move the cursor to four directions to confi rm ststus or after changing a selected item. S witching between AHD and CVBS modes: Press the SET button for more than 5 seconds. 2 Power LED : This lamp is lit when the camera is receiving power normally. 3V ideo OUT Terminal : Sends video signal and connects to the Video IN port of a AHD DVR. 4 Power input terminal : Connect the designated power supplies.
Lens The lens is not supplied with this camera. Purchase a lens suitable for your environment. This camera accepts the auto iris lens and both C-and CS-mount lens. T o use the functions of this camera effectively it is recommended that a DC type Auto Iris lens is used. `` Keep the lens surface clean, if it becomes contaminated with dirt or fingerprints the picture quality suffers. When Using Auto Iris Lens 1.
introduction When Using a C/CS-Mount lens (Sold separately) Before installing a lens, identify whether the lens to be installed is a C-Mount or CS-Mount. This camera is set for a CS-Mount Lens by default. To install a C-Mount Lens, a simple modification is required. yy When Using a CS-Mount Lens Remove the protective glass cover at the front of this product and turn the CS-Mount Lens clockwise to install it. MM `` Use the lens connector shown in the following figure.
yy When Using a C-Mount Lens 1. Remove the protective glass cover at the front of this product and turn the C-Mount Adapter clockwise to install it. ● INTRODUCTION ● introduction C-Mount Adapter C-Mount Adapter C-Mount Adapter 2. Turn the C-Mount lens clockwise to install it. C-Mount Adapter C-Mount Adapter C-Mount Adapter 3. After combining the lens, adjust the focus. 4.
connection Connecting to Monitor Refer to the following figure to connect monitors through DVR. REC HDD ALARM NETWORK BACKUP POWER AHD DVR VIDEO POWER HCB-7000 Monitor yy As the connecting method varies with the instruments, refer to the manual supplied with the instrument. yy Only connect the cable when the power is turned off. MM `` This product supports 2 video output formats of AHD, CVBS. The default is AHD. Select the video output appropriate for your DVR.
When the resistance value of copper wire is at [20°C(68°F)] #24 (0.22mm2) #22 (0.33mm2) #20 (0.52mm2) #18 (0.83mm2) Resistance value(Ω/m) 0.078 0.050 0.030 0.018 Voltage Drop (V/m) 0.028 0.018 0.011 0.006 yy As shown in the table above, voltage decreases as the wire gets longer. Therefore use of an excessively long adaptor output line for connection to the camera may affect the performance of the camera.
connection Using Coaxial Communications yy Coaxial Communications System yy OSD Control method CAMERA DVR SET MENU/ENTER CONTROLLER OSD KEY UP UP KEY JOYSTICK UP DOWN DOWN KEY JOYSTICK DOWN LEFT LEFT KEY JOYSTICK LEFT RIGHT RIGHT KEY JOYSTICK RIGHT REC HDD ALARM NETWORK BACKUP POWER -- Video Cable The camera's video output port is connected to the monitor with a BNC coaxial cable, shown below.
camera operation Menu Configuration MAIN SETUP ◦ AHD ◦ CVBS D-WDR ◦ OFF ◦ ON WHITE BAL ◦ ATW ◦ MANUAL ◦ INDOOR ◦ AWC → SET ◦ OUTDOOR EXPOSURE ◦ BRIGHTNESS ◦ AGC ◦ LENS ◦ DNR ◦ SHUTTER ◦ RETURN BACKLIGHT ◦ OFF ◦ USER BLC ◦ HLC SPECIAL ◦ DISPLAY ◦ DAY/NIGHT ◦ RETURN ◦ COMM ADJ ◦ PRIVACY ◦ IMAGE ADJ ◦ MOTION EXIT ◦ SAVE ◦ NOT SAVE ◦ RESET ● Camera Operation VIDEO FORMAT Menu Setup Use the Function Setup switch within the camera.
camera operation Select the function using the Function Setup switch. MAIN SETUP 1. VIDEO FORMAT 2. D-WDR 3. WHITE BAL AHD OFF ATW Change the status using the Function Setup switch. 4. EXPOSURE 5. BACKLIGHT OFF 6. SPECIAL 7. EXIT SAVE 1. Press the Function Setup switch. yy Main SETUP menu is displayed on the monitor screen. 2. Select a desired function using the Function Setup switch. yy Place the cursor over a desired item. 3. Set up a selected item by using the Function Setup switch. 4.
D-WDR If an object has a large variance between bright and dark areas, it will keep bright areas bright and make selected dark areas bright, so that the overall brightness can be maintained. 2. U se the Function Setup switch to change the D-WDR level in the sub menu according to the contrast between bright and dark areas. MAIN SETUP 1. VIDEO FORMAT 2. D-WDR 3. WHITE BAL OFF ATW 4. EXPOSURE 5. BACKLIGHT OFF 6. SPECIAL 7.
camera operation yy INDOOR : Select this when the color temperature is between 4,500K and 8,500K. Automatically adjusts the camera color for optimization to the indoor environment. yy MANUAL : S elect this to fine-tune White Balance manually. Set White Balance first by using the ATW or AWC mode. After that button to MANUAL mode, finetune the White Balance and the Function Setup switch. WB MANUAL IIIIIIIIIIIIIIIIIIIII 147 1. RED GAIN IIIIIIIIIIIIIIIIIIIII 124 2. BLUE GAIN 3.
-- Manual : T he shutter does not automatically move but is fixed to the maximal degree in this mode. MM `` Some lenses may not work properly, depending on the setting of the BRIGHTNESS LEVEL. greater the shutter value the brighter the screen is but the more the residual MM `` The images of objects there are. `` If the min shutter value is large, it can cause noise, spots and white areas but still operate normally. `` If you do not use the AGC mode on the exposure menu, it cannot be set above 1/60sec.
camera operation yy USER BLC : E nables a user to select a desired area on a picture and view that area more clearly. -- L EVEL : Adjusts the brightness level of a monitoring area. -- TOP/BOTTOM/LEFT/RIGHT : Adjust the area to be enhanced. -- RETURN : Return to the MAIN SETUP menu. LC (High Light Compensation) : yy H This function masks the strong light to minimize white out due to over exposure and preserve much of the on-screen details when the camera aims a strong light source.
SPECIAL 2. Select a desired mode using the Function Setup switch. MAIN SETUP 1. VIDEO FORMAT AHD 2. D-WDR OFF 3. WHITE BAL ATW 4. EXPOSURE 5. BACKLIGHT yy DISPLAY 6. SPECIAL ➊ If the SPECIAL menu screen is displayed, 7. EXIT use the Function Setup switch so that the arrow indicates ‘DISPLAY’. ➋ Select a desired mode using the Function Setup switch. OFF SAVE -- FONT COLOR : You can change the OSD font color.
camera operation yy IMAGE ADJ ❶ If the SPECIAL menu screen is displayed, use the Function Setup switch so that the arrow indicates ‘IMAGE ADJ’. ❷ Select a desired mode using the Function Setup switch. -- GAMMA : The setting range is 0.35 ~ 1.0. The closer to 1.0 the setting is, the darker it gets. IMAGE SETUP USER ▶ 1. GAMMA IIIIIIIIIIIIIIIIIIIII 5 2. PED LEVEL IIIIIIIIIIIIIIIIIIIII50 3. COLOR GAIN 4. H-REV OFF 5. V-REV OFF 6. SHARPNESS ON 7. RETURN -- PED LEVEL : The setting range is 1 ~ 100.
yy BURST MODE : Activate or deactivate the burst mode to maintain or remove the color signal. yy DURATION : This function is used to select the brightness of light where switching occurs. yy DWELL TIME : Y ou can select day/night switching delay time from. 3s, 5s, 7s, 10s, 15s, 20s, 30s, 40s, 60s MM `` If you set the AGC mode to off on the exposure menu, you cannot switch the day/night mode to auto.
camera operation -- AREA : You can select up to 2 PRIVACY areas. -- MODE : Determines whether to use the area selected in the AREA. -- MASK COLOR : Determine area color. You can select Green, Yellow, Red, Blue, Black, White, Gray. -- TRANSPARENCY : Adds or removes transparency from the masking area. -- V POSITION/HEIGHT/H POSITION/WIDTH : Adjust the size and position of the selected area. -- RETURN : Return to the SPECIAL menu.
MM ```` EXIT Select a desired EXIT mode using the Function Setup switch depending on the camera purpose. yy SAVE : Save the current settings and exit the MAIN SETUP menu. yy NOT SAVE : Do not save the current settings and exit the MAIN SETUP menu. yy RESET : Revert camera to factory settings. (The language, communication and lens settings will remain the same). English_31 ● Camera Operation Depending on the shape of an object, there can be errors in size detection.
troubleshooting Troubleshooting If you have trouble operating your camera, refer to the following table. If the guidelines do not enable you to solve the problem, contact an authorized technician. Problems Troubleshooting Nothing appears on the screen. yy Check that the power cord and line connection between the camera and AHD DVR are properly connected. yy Check that you have properly connected BNC cable to the camera. yy Check the type of lens. The image on the screen is dim.
specifications Specifications HCB-7000N/P HCB-7000PH Video 1/3” 4M CMOS Total Pixels 2720(H) x 1536(V) Effective Pixels 2688(H) x 1520(V) Scanning System Progressive Scan Min. Illumination Color : 0.16Lux (F1.2, 1/30sec) B/W : 0.009Lux (F1.2, 1/30sec) S / N Ratio 52dB (AGC off, Weight on) Video Output BNC(AHD), additional CVBS for installation Resolution 2560x1440 Max.
specifications HCB-7000N/P Video Transmission Distance HCB-7000PH 500m(5C2V Coaxial Cable) Environmental Operating Temperature / Humidity -10°C ~ +55°C (+14°F ~ +131°F) / Less than 90% RH Electrical Input Voltage/Current Dual ( 24VAC±10%/300mA & 12VDC±10%/300mA ) AC 230V, 50/60Hz, 70mA Power Consumption Max. 3.6W Max. 4.5W Mechanical Color / Material Black / Aluminum, Ivory / Plastic Dimension (WxHxD) 59.6 × 68.4 × 92.7mm (2.35" × 2.69" × 3.65") 59.6 × 68.4 × 116.6mm (2.35" × 2.69" × 4.
Dimension Unit: mm ● specifications English_35
specifications 36_ specifications Unit: mm
MEMO
Head Office 6, Pangyo-ro 319 beon-gil, Bundang-gu, Seongnam-si, Gyeonggi-do, 463-400 Rep. of KOREA Tel : +82.70.7147.8753 Fax : +82.31.8018.3740 www.hanwha-security.com Hanwha Techwin America 500 Frank W. Burr Blvd. Suite 43 Teaneck, NJ 07666 Toll Free +1.877.213.1222 Direct +1.201.325.6920 Fax +1.201.373.0124 www.hanwha-security.com Hanwha Techwin Europe Heriot House, Heriot Road, Chertsey, Surrey, KT16 9DT, United Kingdom Tel +44.1932.57.8100 Fax +44.1932.57.8101 www.hanwha-security.
