ENGLISH •Digimax V10 User's Manual Thank you for buying a Samsung Camera. This manual will guide you through using the camera, including capturing images, downloading images and using the software applications. Please read this manual carefully before using your new camera.
Instructions Use this camera in the following order Set up the camera driver Before connecting the camera to a PC, via the USB cable, you will need to set up the camera driver. Install the camera driver that is contained in Application software CD-ROM.(p.110) Take a picture (p.22) Take a picture Insert the USB cable Check the camera’s power Check [Removable Disk] Insert the supplied USB cable into the PC’s USB port and the camera’s USB connection terminal.(p.120) Check the camera’s power.
Contents READY Getting to know your camera About the icons Danger Warning Caution An FCC warning System chart Identification of features Front & Top Back Side/ 5-function button Mode dial Connecting to a Power Source Using the AC power adapter Using the batteries Removing the battery Instructions on how to use the memory card Inserting the memory card Removing the memory card When Using the Camera for the First Time 5 5 6 6 7 7 8 10 10 10 11 11 14 15 16 16 17 19 19 20 RECORDING LCD monitor indicator Start
Contents PLAY Starting play mode Playing back a still image Playing back a movie clip How to capture the movie clip On camera movie trimming Playing back a recorded voice LCD monitor indicator Using the camera buttons to adjust the camera Thumbnail / Enlargement button Voice memo / Up button Play & Pause/ Down button LEFT/ RIGHT/ MENU/ OK button LCD button Delete button Album button (MF button) Setting up the play back function using the LCD monitor Starting the slide show Protecting images Deleting images
Getting to know your camera Thank you for buying a Samsung Digital Camera. Prior to using this camera, please read the user manual thoroughly. When you require After Sales service, please bring the camera and the cause of the camera malfunction (such as Batteries, Memory card etc.) to the A/S centre. Please check that the camera is operating properly prior to when you intend to use it (e.g. for a trip or an important event) to avoid disappointment.
Danger Do not attempt to modify this camera in any way. This may result in fire, injury, electric shock or severe damage to you or your camera. Internal inspection, maintenance and repairs should be carried out by your dealer or Samsung Camera Service centre. Please do not use this product in close proximity to flammable or explosive gases, as this could increase the risk of explosion. Should any form of liquid or a foreign object enter the camera, do not use it.
Caution Leaking, overheating, or burst batteries could result in fire or injury. Use batteries with the correct specification for the camera. Do not short circuit, heat or dispose of batteries in fire. Do not insert the batteries with the reverse polarities. Remove the batteries when not planning to use the camera for a long period of time. Batteries may leak corrosive electrolyte and permanently damage the camera's components. Do not fire the flash while it is in contact with hands or objects.
System chart Please check that you have the correct contents before using this product. To buy the optional equipment, contact your nearest Samsung dealer or Samsung service centre. < Included items > Pouch Remote control DPOF compatible printer(see p.81) User manual Waranty card Camera strap SD memory card (see p.17) AC adapter (SAC-32, DC 3.3V 2.0A) Rechargeable battery (SLB-1137) CHARGE AC cord 8 Battery charger (SBC-L3) Software CD (see p.
System chart System Requirements For Windows Computer (see p.120) PictBridge compatible printer(see p.83) PC with processor better than MMX Pentium 233MHz (XP : Pentium II 300MHz) Windows 98/98SE/2000/ME/XP Minimum 32MB RAM (XP : 128MB) 140MB of available hard-disk space USB port CD-ROM drive 800x600 pixels, 16-bit colour display compatible monitor (24-bit colour display recommended) For Macintosh USB cable AV cable Power Mac G3 or later Mac OS 9.2 ~ 10.
Identification of features Front & Top Mode dial Shutter button Power button Jog dial Mode dial lamp Speaker Flash Auto Focus lamp & Selftimer lamp Viewfinder Lens Remote control sensor Microphone Back LCD button Flash indicator lamp(Red) Autofocus indicator lamp(Green) Zoom W button (Thumbnail) Zoom T button (Digital zoom) +/-, DELETE button 5-function button AEL/ASM button Strap eyelet MF button (Album button) USB/ AV connection terminal LCD monitor Tripod socket Play mode button 10 D
Identification of features Side/ 5-function button Battery chamber cover Voice Recording / Voice memo/ UP button FLASH/ LEFT button Battery chamber SELF-TIMER/ Remote/ RIGHT button MENU/ OK button Battery holder Memory card slot Macro/ Play & Pause button/ DOWN button Mode dial You can select the desired working mode by using the mode dial located on the top of the camera. This digital camera has 8 recording modes. These are listed below.
Identification of features A (Aperture priority) shooting mode Set the aperture value for automatic exposure depends on the brightness of the object by automatic shutter speed setting in the camera. S (Shutter priority) shooting mode Set the shutter speed for automatic exposure depends on the brightness of the object by automatic aperture value setting in the camera. M (Manual) shooting mode The user can manually set both the aperture value and the shutter speed.
Identification of features Self-timer lamp (Based on 10-second Self-timer; see p. 37) Colour Status Red Blinking Camera Status - For the first 8 seconds, the LED blinks at 1second intervals. - For the final 2 seconds, the LED blinks quickly at 0.25-second intervals.
Connecting to a Power Source There are two ways in which to provide the camera with power. You can use batteries or alternatively, you can use an AC(100 ~ 250V) Adapter (DC 3.3V 2.0A). We recommend using rechargeable battery (SLB-1137). INFORMATION Important information about battery usage When the camera is not used, turn off the camera power. Do not charge the non rechargeable batteries. It may cause an explosion. Please remove the batteries if the camera will not be used for long periods.
Connecting to a Power Source Using the AC power adapter (SAC-32, DC 3.3V 2.0A, optional) If you have access to a mains supply, using an AC Adapter (SAC-32, DC 3.3V 2.0A) allows the camera to be used for long periods of time. Plug the adapter into the connection point (DC IN 3.3V) on the camera. Remove the batteries from the camera when using an AC adapter. DANGER Always turn off the power before taking the AC adapter out of the mains supply. As with all mains powered devices, safety is important.
Connecting to a Power Source Using the batteries : If the camera does not turn on after you have inserted batteries, please check whether the batteries are inserted with the correct polarity(+/-). 1. Open the battery chamber cover by pushing in the direction of the arrow. 2. Insert the batteries taking note of the polarity (+ / -). 3. To close the battery chamber cover, push it until it clicks. Removing the battery 1. Turn off the camera power.
Instructions on how to use the memory card Maintenance of the memory card Be sure to format the memory card (see p.91) if you are using a newly purchased memory for the first time, if it contains data that the camera cannot recognise, or if it contains images captured with a different camera. Turn off the camera power whenever the memory card is being inserted or removed. Repeated use of the memory card will eventually reduce the memory card’s performance.
Instructions on how to use the memory card INFORMATION Don't remove the memory card when the Auto focus lamp(Green) is blinking as this may cause damage to data in the memory card. The camera can use SD Memory Cards and MMC (Multi Media Cards). Please consult the enclosed manual for using the the MMC Cards. The SD memory card has a write protect switch that prevents image files from being deleted or formatted. By sliding the switch to the bottom of the SD memory card, the data will be protected.
Inserting the memory card 1. Turn off the camera’s power and pull the battery chamber cover in the direction of the arrow to open. 2. Have the front of the memory card facing toward the front of the camera (lens) and the card pins toward the back of the camera (LCD monitor), and then push the memory card into the card slot until you hear a click. 3. To close, push the battery chamber cover until you hear a click. If the memory card does not slide in smoothly, do not attempt to insert it by force.
When Using the Camera for the First Time If the camera is turned on for the first time, a menu will be displayed to set date, time and language in the LCD monitor. This menu will not be displayed after setting up the date, time and language. Set up the date, time and language before using this camera. Setting up the date, time and date type 1. Select the [D & Time] menu by pressing the UP/DOWN button and press the RIGHT button. 2.
LCD monitor indicator The LCD monitor displays information about the shooting functions and selections. [ Image & Full Status ] No. Description Icons Page 1 Battery p.16 2 Recording mode p.11~12 3 Shooting type p.52 4 Flash p.34 5 Self-timer p.37 6 Voice memo p.32 7 Macro p.33 8 Metering p.51 9 AEL p.43 10 Manual/ Continuous auto focus p.44 11 Sharpness p.53 12 Auto focus frame 13 Camera shake warning 14 Date/ Time p.
LCD monitor indicator 15 Exposure compensation p.42 16 White Balance p.41 17 ISO p.41 18 RGB 19 Image quality 20 Image size 3072, 2816, 2592, 2272, 2048, 1600, 1024, 640 Number of available shots remaining 16 Remaining time (Movie clip/ Voice recording) 00:01:30/ 01:00:00 21 22 RGB p.40 p.50 p.49 Optical/ Digital Zoom bar Starting the recording mode How to use the AUTO mode ( ) 1. Insert the batteries (p.16). Insert the batteries taking note of the polarity (+ / -). 2.
Starting the recording mode How to use the PROGRAM mode ( ) Selecting the automatic mode will configure the camera with optimal settings. You can still manually configure all functions except the aperture value and shutter speed. Steps from 1-4 are the same as those for AUTO mode. 5. Select the PROGRAM mode by rotating the mode dial. 6. Press the menu button to configure advanced functions such as image size (p.49), quality (p.50), metering (p.51), continuous shooting (p.52) , picture effects (p.
Starting the recording mode How to use the SHUTTER PRIORITY mode ( ) Steps from 1-4 are the same as those for AUTO mode. 5. Select the SHUTTER PRIORITY mode by rotating the mode dial. 6. Select the desired shutter speed by rotating the jog dial. 7. Point the camera towards the subject and compose the image by using either the viewfinder or LCD monitor. 8. Press the shutter button to capture an image. * High Shutter speeds can capture a moving object in a still image as if the object is not moving.
Starting the recording mode How to use the MySET mode ( ) This mode allows users to save frequently used shooting settings for later use. Steps from 1-4 are the same as those for AUTO mode. 5. Select the MySET mode by rotating the mode dial. 6. Press the menu button. 7. Use the Left/Right buttons to select the [Load Myset] menu tap. Use the Up/Down buttons to select desired MySET number. 8. Press the OK button to load the camera configuration saved in the MySET number and close the menu screen. 9.
Starting the recording mode Pausing while recording a movie clip (Successive Recording) This camera allows you to temporarily stop during unwanted scenes, while recording a movie clip. Using this function, you can record your favourite scenes into a movie clip without having to create multiple movie clips. Using Successive Recording Steps from 1-6 are the same as those for MOVIE CLIP 00:00:04 640 mode. 7. Point the camera towards the subject and compose the image by using the viewfinder or LCD monitor.
Starting the recording mode How to use the SCENE mode ( ) Use the menu to easily configure optimal settings for a variety of shooting situations. These include NIGHT, PORTRAIT, CHILDREN, LANDSCAPE, CLOSE UP, TEXT RECOGNITION, SUNSET, DAWN, BACKLIGHT, FIREWORKS and BEACH & SNOW scenes. Steps from 1-4 are the same as those for AUTO mode. 5. Select the SCENE mode by rotating the mode dial. 6. Press the menu button and select the [Scene] menu by pressing the left and right button. 7.
Things to Watch Out for When Taking Pictures Pressing the shutter button down half way. Lightly press the shutter button to confirm focus and flash battery charge. Press the shutter button all way down to take the picture. [ Lightly press the shutter button ] [ Press the shutter button ] The available recording time may vary depending on shooting conditions and camera settings.
Using the camera buttons to adjust the camera The RECORDING (AUTO, PROGRAM, APERTURE PRIORITY, SHUTTER PRIORITY, MANUAL, MySET, MOVIE CLIP, SCENE) mode function can be set up by using the camera buttons. POWER button Used for turning the camera’s power on / off. If there is no operation during the specified time, the camera's power will be turned off automatically to save battery life. Refer to page 90 for more information about the auto power off function.
ZOOM W/T button This camera has a 3X optical zoom and a 10X digital zoom function. Using both will offer a total zoom ratio of 30X. TELE Zoom Optical zoom TELE Digital zoom TELE : Pressing the ZOOM T button. This will zoom into the subject i.e. the subject will appear nearer. : When the maximum (3X) optical zoom is selected, pressing the ZOOM T button activates the digital zoom software. Releasing ZOOM T button stops the digital zooming at the required setting.
ZOOM W/T button INFORMATION To use the digital zoom the LCD monitor has to be turned on. Images taken using the digital zoom may take a little longer for the camera to process. Allow time for this to take place. The digital zoom cannot be used in movie clip shots. If the movie clip is being recorded, the zoom operation cannot be activated. You may notice a decrease in image quality when using the digital zoom.
Voice memo( ) / UP button While the menu is showing, press the UP button to move up the submenu cursor. When the menu is not displayed on the LCD monitor, the UP button operates as the voice memo ( ) button. You can add your voice-over to a stored still image. Recording a voice memo 1. Rotate the MODE DIAL to select a RECORDING mode with the exception of MOVIE CLIP mode. 2. Press the VOICE MEMO ( ) button. If the voice memo indicator is displayed on the LCD monitor, the setting is completed.
Macro( ) / Down button (Focusing) While the menu is showing, press the DOWN button to move from the main menu to a submenu, or to move down the submenu cursor. When the menu is not showing, you can use the MACRO/ DOWN button to take macro pictures (within the distance range of 4-80 cm).
Focus lock To focus on the subject positioned outside of the centre, use the focus lock function. Using the Focus Lock 1. Ensure the subject in the centre of the autofocus frame. 2. Press the SHUTTER button halfway. When the green auto lights up, it means the camera is focused on the subject. Be careful not to press the SHUTTER button all the way down to avoid taking an unwanted pictured. 3.
FLASH( ) / LEFT button Flash range Unit : m AUTOFOCUS MACRO AUTO MACRO ISO AUTO WIDE TELE WIDE TELE WIDE TELE 0.8~3.0 0.8~2.0 0.2~0.8 0.25~0.8 0.2~3.0 0.25~2.0 INFORMATION Using the flash frequently will reduce the life of the batteries. Under normal operating conditions the charging time for the flash is normally within 7 seconds. If the batteries are weak, the charging time will be longer. During the continuous shot, movie clip mode, the flash function will not operate.
FLASH( ) / LEFT button Flash mode indicator Icon Flash mode Description Auto flash If the subject or background is dark, the camera flash will operate automatically. Auto & Red eye reduction If a subject or background is dark, the camera flash will work automatically and will reduce the red-eye effect by using the red-eye reduction function. Fill in flash Slow synchro The flash fires regardless of available light.
Self-timer( ) / Remote ( )/ Right button When the menu is displayed on the LCD monitor, pressing the Right button makes the cursor shift to the right tab. The right button can also be used to move to a sub menu to select a different setting. When the menu is not displayed on the LCD monitor, the RIGHT button operates as the Selftimer ( ) and Remote ( ) button. This function is used when the photographer would also like to be in the image. Using the self-timer and remote control. 1.
Self-timer( ) / Remote ( )/ Right button Self-timer/ remote mode setting Mode dial Setting ( marked camera working mode is the default setting.) AUTO PROGRAM A/S/M, MySET Off 2s self-timer 10s self-timer Double self-timer Remote SCENE MOVIE CLIP Off 10s self-timer Remote INFORMATION When taking a picture using the self-timer, the self-timer lamp works as follows: 2 second self-timer setting : The self-timer lamp blinks at 0.25 second interval for 2 seconds.
Self-timer( ) / Remote ( )/ Right button Replacing batteries for the remote control Make sure the + polarity is toward the top and the - polarity is toward the bottom while installing batteries for the remote control. Replace batteries for the remote control in the local service centre. Use the CR 2025 3V batteries.
+/- button You can use the +/- button to adjust the values for the RGB, ISO, white balance and exposure compensation. Main menu Sub menu RGB R (Red), G (Green), B (Blue) ISO AUTO, 50, 100, 200, 400 Available camera mode AUTO, DAYLIGHT, CLOUDY, FLUORESCENT H, WHITE BALANCE FLUORESCENT L, TUNGSTEN, CUSTOM. Exposure compensation -2.0~0.0~+2.0(1/3EV steps) RGB : Allows the user to adjust the R (Red), G (Green), and B (Blue) values of the images to be captured. Setting RGB Values 1.
+/- button ISO: You can select the ISO sensitivity when taking pictures. The speed or specific light-sensitivity of a camera is rated by ISO numbers. Selecting an ISO Sensitivity 1. Press the +/- button, and then use the UP and DOWN buttons to select the ISO icon( ). The ISO menu bar will appear as shown. 2. Use the LEFT and RIGHT buttons to select the desired ISO sensitivity value. - AUTO : The camera's sensitivity is automatically changed by variables such as lighting value or subject brightness.
+/- button Using the Custom White Balance White balance settings may vary slightly depending on the shooting environment. You can select the most appropriate white balance setting for a given shooting environment by setting up the custom white balance. 1. Select the CUSTOM ( ) menu of the White Balance. You can select CUSTOM 1 or CUSTOM 2 white balance. 2. Place a sheet of white paper in front of the camera so that the LCD monitor shows only white, and then press the SHUTTER button. 3.
AEL/ASM button The camera measures brightness of the object and automatically set the best exposure value. If difference between the exposure values of the object and background is too great, use the AEL button to manually set the exposure value against sunlight or in strong light. This button is available in the PROGRAM, Aperture priority(A), Shutter priority(S), MySET and MOVIE CLIP mode. Use the automatic exposure lock. 1. Ensure the subject in the centre of the autofocus frame. 2.
MF button Use this button to select the focusing method. Automatic focusing : Slightly press the shutter to let the camera measure distance to the object and select the best focusing. If successfully focused with the slight press of the shutter, the automatic focusing mark is turned green. Manual focusing : Where the automatic focusing is not available, for example, in very dark conditions, use the manual focus. Please be careful when using the manual focus as the picture can be blurred easily.
LCD( ) button You can check the recording status in the LCD monitor. In any mode with the exception of VOICE RECORDING mode, pressing the LCD button will change the display as shown below. Pressing the LCD button [Image & full information] Pressing the LCD button [Histogram] Pressing the LCD button [Image & basic information] [LCD off] Histogram Shows you the distribution of brightness in recorded images. If the bars in the histogram are higher towards the right, the image may be too bright.
Using the LCD monitor to adjust the camera settings You can use the menu on the LCD monitor to set up recording functions. In any mode with the exception of VOICE RECORDING mode, pressing the MENU button displays the menu on the LCD monitor. INFORMATION The menu will not be displayed on the LCD monitor in the following circumstances: - When another button is being operated. - While image data is being processed. (when the green lamp next to the viewfinder blinks) - When there is no battery capacity.
Using the LCD monitor to adjust the camera settings Menu tab Main menu Sub menu Camera working mode Page TIFF S. Fine p.50 Quality Fine Normal Multi Metering p.51 Spot Single Continuous Shooting p.52 AEB AFB Soft Sharpness Normal p.53 Vivid Normal B&W p.53 Effect Sepia Negative Off Range 1 HighLight p.54 Range 2 Range 3 Off 2 Parts Special Effect Composite p.55 3 Parts 4 Parts Off Photo Frame1 Frame Frame2 p.
Using the LCD monitor to adjust the camera settings Menu tab Main menu Sub menu Camera working mode Page Myset1 Save Myset Myset2 p.57 Myset3 Myset1 Load Myset Myset2 p.57 Myset3 Scene Stabilizer Night, Portrait, Children, Landscape, Close up, Text, Sunset, Dawn, Backlight, Firework, Beach&Snow Off On * Menus are subject to change without prior notice. 48 p.58 p.
How to use the menu 1. Turn on the camera and press the MENU button. A menu for each camera mode appears. However, there is no menu for Voice Recording mode ( ). 2. Use the LEFT and RIGHT buttons to navigate through the menus. Press the LEFT or RIGHT button. 3072 Quality TIFF S.Fine Fine Normal Press the LEFT or RIGHT button. 3027 Metering NOR Shooting Single Continuous AEB AFB Multi Spot 3. Use the UP and DOWN buttons to select a sub menu. Press the UP or DOWN button.
Quality You can select the compression ratio appropriate for your application of the captured images. The higher the compression ratio, the lower the picture quality. 3072 Quality TIFF S.Fine Fine Normal [ PROGRAM mode ] STILL IMAGE mode Mode MOVIE CLIP mode Icon TIFF Sub menu TIFF S. Fine Fine Normal 30FPS 15FPS File Format tif jpeg jpeg jpeg avi avi INFORMATION TIFF is the highest quality and Normal is the lowest setting. Choose the setting appropriate for your needs.
Metering If you cannot obtain suitable exposure conditions, you can change the metering method to take brighter pictures. Multi ( Spot ( ) ) : Exposure will be calculated based on an average of the available light in the image area. However, the calculation will be biased towards the centre of the image area. This is suitable for general use. 3072 Metering Multi Spot [ PROGRAM mode ] : Only the rectangular area in the centre of the LCD monitor will be metered for light.
Continuous shot You can select continuous shot, AEB (Auto Exposure Bracketing) and AFB (Auto Focus Bracketing). If you select CONTINUOUS, AEB or AFB, the flash will automatically be set to Flash Off. [Single]: Take one picture only NOR [Continuous]: Images will be taken continuously until the shutter button is released. The shooting capacity depends on the memory. Shooting Single Continuous AEB AFB [ PROGRAM mode ] [AEB]: You can select the exposure bracket range ( 0.
Sharpness You can adjust the sharpness of the picture you want to take. You cannot check the sharpness effect on the LCD monitor before you take a picture, because this function is applied only when the captured image is stored on the memory. NOR Sharpness Soft Normal Vivid [ PROGRAM mode ] Sub menu Icon Description The edges of the image are softened. This effect is suitable for editing images on your PC. Soft The edges of the image are sharp. This is suitable for printing.
Special Effect By using the camera s digital processor, it is possible to add special effects to your images. You can select this menu only in the PROGRAM, MySET, Aperture priority, Shutter priority and MANUAL modes. You can select this menu only in the 2592x1944, 2272x1704, 2048x1536, 1600x1200, 1024x768, 640x480 image size. If the [3072X2304] or [2816X2112] image size is selected and one of the special effect menu is selected, the image size is changed to the [2592X1944] automatically.
Special Effect : Composite shots You can combine 2~4 different shots in a still image. 1. Select the PROGRAM, MySET, Aperture priority, Shutter priority or MANUAL modes. Then press the menu button. 2. Press the LEFT/ RIGHT button and select the [Special Effect] menu tab. NOR Special Effect 3. Select the [Composite] menu by pressing the UP/ DOWN HighLight Off button and press the Right button. Composite Off 4. Select a desired sub menu by pressing the UP/ DOWN Off Photo Frame button and press the OK button.
Special Effect : Photo Frame You can add 3 types of frame-like borders to a still image you want to capture. 1. Select the PROGRAM, MySET, Aperture priority, Shutter priority or MANUAL modes. Then press the menu button. 2. Press the LEFT/ RIGHT button and select the [Special Effect] menu tab. 3. Select the [Photo Frame] menu by pressing the UP/ DOWN button and press the Right button. 4. Select a desired sub menu by pressing the UP/ DOWN button and press the OK button.
Save / Load a specific camera configuration (MySET) Use the MySET mode to save frequently used camera settings (Save Myset) and use it later (Load Myset) Saving the camera configuration : Available in the PROGRAM, A, S and M shooting mode. 1. Use the camera buttons and menu to set desired camera configuration. 2. Press the menu button in any mode except AUTO, VOICE RECORDING, MOVIE CLIP, SCENE and MySET NOR Save Myset mode. 3. Press the Left/Right buttons to select the [Save Myset] Myset 1 menu tap.
Scene Select the [Scene] submenu to automatically configure optimal settings, depending on the selected scene. Only available in the SCENE Mode. 3072 Scene Night Portrait Children Landscape [SCENE mode] Sub menu Icon Night Description Use this for shooting still images at night or in other dark conditions.
Movie Clip frame stabiliser This function helps stabilise images captured during movie recording. You can select this menu only in the MOVIE CLIP mode. How to use this function 1. Select the MOVIE CLIP mode by rotating the mode dial and press the menu button. Select the [Stabilizer] menu NOR Stabilizer and press the right button. 2. Select a desired sub menu by pressing the Up/Down Off button and press the OK button. On [Off] : Movie clip frame stabilizer function becomes disabled.
Starting play mode Turn the camera on and select Play mode by pressing the play mode button ( ). The camera can now play back the images stored in the memory. If you have turned on the camera by pressing the POWER button, you can press the PLAY MODE button once to switch to Play mode and press it again to switch to Recording mode. You can turn the power on with the play mode button. The camera is turned on in play mode. Press the play mode button again to turn off the camera.
Starting play mode Playing back a movie clip Steps from 1-2 are the same as those to play back a still image. 3. Select the recorded movie clip that you want to play back by using the LEFT/RIGHT button. If you select a movie clip, the movie clip indicator ( ) will be displayed on the LCD monitor. 4. Press the play & pause button ( ) to play back a movie clip file. - To pause a movie clip file while playing it back, press the play & pause button again.
Starting play mode On camera movie trimming : You can extract desired frames of movie clip during the movie clip play back. 1. Select a desired movie clip in the play mode. 9 2. Play back the movie clip by pressing the Play & Pause button. 3. Press the Pause button at the point of the movie clip Trim:T Capture:SH that you want to start extracting. PLAY 4. Press the T button. The start point doesn't display on FF REW the status bar, but the start point will be selected. 5.
Starting play mode Playing back a recorded voice Steps from 1-2 are the same as those to play back a still image. 3. Select the recorded voice that you want to play back by using the LEFT/RIGHT button. If you select a recorded voice file, the voice indicator ( ) will be displayed on the LCD monitor. PLAY 4. Press the play & pause button ( ) to play back a recorded voice file. - To pause a recorded voice file, while playing it back, press the play & pause button again.
LCD monitor indicator The LCD monitor displays information about the shooting conditions. No. Description Icon Page 1 Battery 2 Play mode 3 File Type 4 Voice memo p.66 5 Protect indicator p.77 6 DPOF indicator p.81 7 Stored image number 8 TIFF file p.16 9 If you press the LCD button, you can check the following recording information: Size Av Tv ISO Flash Date 64 : : : : : : 3072X2304 F2.8 1/60 75 Off 2005/01/01 Size Av Tv ISO Flash : 3072X2304 : F2.
Using the camera buttons to adjust the camera In Play mode, you can use the buttons on the camera to conveniently set up the Play mode functions. Thumbnail ( ) / Enlargement ( ) button You can view multiple pictures, enlarge a selected picture, and crop and save a selected area of an image. Thumbnail display 1. While an image is displayed full screen, press the thumbnail button. 2. The thumbnail display will highlight the image that had been showing at the time the thumbnail mode was selected. 3.
Thumbnail( ) / Enlargement( ) button The maximum enlargement rate in proportion to the image size. Image size 3072 2816 2592 2272 2048 1600 1024 640 Maximum enlargement rate X12.0 X11.0 X10.1 X8.8 X8.0 X6.2 X4.0 X2.5 Trimming : You can extract part of the image that you want and save it separately. Trimming? 1. Select an image that you want to enlarge and press the Trimming Cancel enlargement button. Confirm:OK 2.
Voice ( ) memo / Up button 3. Press the shutter button to start recording and voice will be recorded to the still image for 10 seconds. While the voice is recording, the recording status window will be displayed as shown alongside. STOP:SHUTTER 4. The recording can be stopped by pressing the shutter button again. 5. The ( ) icon will be displayed on the LCD monitor after voice memo recording has finished. - Voice memos can’t be recorded onto movie clip files.
LEFT/ RIGHT/ MENU/ OK button LEFT / RIGHT/ MENU/ OK buttons activate the following. - LEFT button : While the menu is showing, press the LEFT button to select the menu tab to the left of the cursor. - RIGHT button : While the menu is showing, press the RIGHT button to select the menu tab to the right of the cursor, or to move an secondary menu. - MENU button : When you press the MENU button, the play mode menu will be displayed on the LCD monitor.
Delete ( ) button This deletes images stored on the memory card. Deleting Images in Play Mode 1. Select an image that you want to delete by pressing the LEFT / RIGHT button and press the DELETE ( ) button. 2. A message will display as shown alongside on the LCD monitor. 3. Select the submenu values by pressing the UP/DOWN button and then press the OK button. If [Delete] is selected: deletes the selected images. If [Cancel] is selected: cancels "Delete Image".
Album button (MF button) You can organise the captured still images(except for the TIFF file type image) into albums by using the MF button. This camera has 8 albums and each album can take up to 100 images. The album menu loading time depends on the memory card type. How to use the album Selecting the album 1. In the play mode, press the MF button. All A1 A2 A3 A4 A5 A6 A7 A8 Select Slide Add 2. Select the [Select] menu by pressing the Up/Down button and press the Right button. 3.
Album button (MF button) 3. Select the still images you wish to add by pressing the Up/Down/Left/Right buttons and press the Zoom T button. marks are displayed on the selected images. * To cancel the selection, press the Zoom T button again. A4 Select Slide Add Remove Select:T 4. Press the OK button and a confirmation window will display. Select a desired sub menu by pressing the UP/ DOWN button and press the OK button. [Add] : Inserts the selected images into the album.
Album button (MF button) Playing back the albums Playing back all of the albums 1. Select [All] menu and press the OK button. All of the albums will be selected. 2. Select the [Slide] menu by pressing the Up/Down button and press the Right button. You can select [Start], [Interval], [Repeat] and [Effect] menus. - [Start] : Start the slide show - [Interval] : Set the slide show play interval - [Repeat] : Choose to repeat the slide show after finishing the first cycle.
Setting up the play back function using the LCD monitor PLAY mode functions can be changed by using the LCD monitor. In the PLAY mode, pressing the MENU button displays the menu on the LCD monitor. The menus you can set up in Play mode are as follows. To capture an image after setting up the play menu, press the PLAY mode button or shutter button. Menu tab Main menu Slide Sub menu Secondary menu Start - Interval 1, 3, 5, 10sec Repeat Off, On Page p.
Setting up the play back function using the LCD monitor This menu is available while the camera is connected to a PictBridge supporting printer (direct connection to the camera, sold separately) with a USB cable. Menu tab Main menu Images Sub menu Secondary menu One Pic - All Pics - No - Yes - Page p. 84 p. 85 Auto Set Auto Postcard 4X6 Size 2L A4 Letter A3 Auto Full 1 Custom Set 2 Layout 4 8 9 16 Auto Plain Type Photo Fastphoto 74 p.
Setting up the play back function using the LCD monitor Menu tab Main menu Sub menu Secondary menu Page Auto Draft Quality Normal Fine Auto Custom Set p. 85 Date Off On Auto File Name Off On Standard - Index - No - Yes - No - Yes - p. 86 Print DPOF Print p. 86 Reset p. 87 Menus are subject to change without prior notice.
Starting the slide show Images can be displayed continuously at pre-set intervals. You can view the slide show by connecting the camera to an external monitor. 1. Press the play mode button and press the menu button. 2. Press the LEFT/ RIGHT button and select the [Slide] menu tab. Slide Start Interval Repeat 1 sec OFF Start the slide show: The slide show can start only in the Exit: MENU Move : [Start] menu. 1. Use the Up/Down buttons to select the [Start] menu. 2.
Starting the slide show Configure slide show effects: Unique screen effects can be used for the slide show. 1. Select the [Effect] sub menu by pressing the UP/ DOWN button and press the RIGHT button. 2. Use the Up/Down Button to select the type of effect. Interval [Cancel] : Normal display. Repeat [Effect 1] : Image is displayed slowly. Effect [Effect 2] : Image is displayed slowly from the centre Back: outwards. [Effect 3] : Image moves from the top left.
Protecting images - If you protect an image, the protect icon will be displayed on the LCD monitor. (An unprotected image has no indicator) - An image in LOCK mode will be protected from the delete function or [Delete] functions, but will NOT be protected from the [Format] function. Deleting images Of all the files stored in the memory card, the unprotected files in the DCIM subfolder will be deleted. Remember that this will permanently delete unprotected images.
Resize Change the resolution (size) of pictures taken. Select the [User Image] to save an image to be the start-up image. The resized image will have a new file name. 1. Press the play mode button and press the menu button. 2. Press the LEFT/ RIGHT button and select the [Resize] menu tab. Resize 2816X2112 3. Select a desired sub menu by pressing the UP/ DOWN 2592X1944 button and press the OK button.
Rotating an image You can rotate the stored images by various degrees. Once the playback of the rotated picture is finished, it will switch back to the original state. 1. Press the play mode button and press the menu button. 2. Press the LEFT/ RIGHT button and select the [Rotate] Rotate menu tab. Right 90˚ 3. Select a desired sub menu by pressing the UP/ DOWN Left 90˚ button. 180˚ 4. Press the OK button and the rotated image will be Exit: MENU Move : displayed.
DPOF DPOF(Digital Print Order Format) allows you to embed printing information on your memory card’s MISC folder. Select the pictures to be printed and how many prints to make. The DPOF indicator will display on the LCD monitor when an image that has DPOF information plays back. Images can then be printed on DPOF printers, or at an increasing number of photo labs. This function is not available for Movie clips and Voice recording files.
DPOF : INDEX Images (except for movie clips and voice file) are printed as index type. 1. Press the play mode button and press the menu button. 2. Press the LEFT/ RIGHT button and select the [DPOF] DPOF menu tab. Standard 3. Select the [Index] menu by pressing the UP/ DOWN Index No button and press the RIGHT button. Size Yes 4. Select a desired sub menu by pressing the UP/ DOWN Back: Set : OK button. If [No] is selected : Cancel the index print setting.
PictBridge You can use the USB cable to connect this camera to a printer that supports PictBridge (sold separately) and print the stored images directly. TIFF, Movie clips and voice files cannot be printed. You can set up the following settings from the PictBridge menu. Images : Select the pictures to be printed.
PictBridge: Picture Selection Select pictures to print 1. Connect the camera to your printer. The USB menu must be set to [Printer] before you connect the camera to the Images printer. (See p.83) One Pic 2. The [Images] menu will appear. 3. Use the UP and DOWN buttons to select the desired All Pics submenu value, and then press the OK button. Move : When [One Pic] is selected : The PictBridge function will be applied only to the picture currently displayed.
PictBridge: Print Setting AUTO SET 1. Connect the camera to your printer. The USB menu must be set to [Printer] before you connect the camera to the printer. (See p.83) No 2. Use the LEFT and RIGHT buttons to select the [Auto Set] menu tab. Yes 3. Use the UP and DOWN buttons to select the desired submenu value, and then press the OK button. [No] : [Custom Set] values are kept. [Yes] : All values in the [Custom Set] are automatically changed.
PictBridge: Printing Printing Pictures 1. Connect the camera to your printer. The USB menu must be set to [Printer] before you connect the camera Print to the printer. (See p.83) Standard 2. Use the LEFT and RIGHT buttons to select the [Print] menu tab. Index Move: 3. Use the UP and DOWN buttons to select the desired submenu value, and then press the OK button. [Standard] : Print the pictures stored in the memory card in set numbers. One picture is printed on one piece of paper.
PictBridge : RESET Initialises user-changed configurations. 1. Connect the camera to your printer. The [USB] menu must be set to [Printer] before you connect the camera to the printer. (See p.83) 2. Use the LEFT and RIGHT buttons to select the [Reset] No menu tab. Yes 3. Use the UP and DOWN buttons to select the desired submenu value, and then press the OK button. - If [No] is selected : Settings will not be reset. - If [Yes] is selected : All print and image settings will be reset.
Setup menu In this mode, you can set up basic settings. You can use the setup menu in all camera modes, except Voice Recording mode. The items indicated by are default settings. Menu tab Main menu Sub menu Secondary menu Reset - Series - Off, 1, 3, 5, 10 min - ENGLISH P”CCK»… p.89 File Power Off Page p.90 PORTUGUÊS Language FRANÇAIS DUTCH DEUTSCH DANSK ESPAÑOL SVENSKA ITALIANO SUOMI p.
Setup menu Menu tab Main menu Sub menu Secondary menu Computer - Printer - Off - On - Dark - Normal - Bright - NTSC - PAL - Off/ 0.5, 1, 3sec - No - Yes - p.93 USB p.94 AF Lamp LCD Video Out Quick View Page p.94 p.95 p.96 p.96 Reset * Menus are subject to change without prior notice. File name This function allows the user to select the file naming format. Assigning File Names 1. In any mode with the exception of Voice Recording mode, 3072 press the MENU button.
File name INFORMATION The first stored folder name is 100SSCAM, and the first file name is SV100001. File names are assigned sequentially from SV100001 SV100002 ~ SV109999. The folder number is assigned sequentially from 100 to 999 as follows : 100SSCAM 101SSCAM ~ 999SSCAM. The files used with the memory card conform to the DCF(Design rule for Camera File systems) format. Auto power off This function switches the camera off after a set amount of time in order to prevent unnecessary battery drainage.
Language There is a choice of languages that can be displayed on the LCD monitor. Even if the batteries or AC adapter are removed and inserted again, the language setting will be preserved. Setting Language 1. In any mode with the exception of Voice Recording mode, press the MENU button. 3072 2. Press the LEFT/ RIGHT button and select the [Setup] Setup menu tab. File English 3. Select the [Language] menu by pressing the UP/ DOWN Power Off Language Français button and press the RIGHT button.
Setting up the Date/ Time/ Date type You can change the date and time that will be displayed on the captured images and set up the date type. Setting Date/Time & Selecting Date Format 1. In any mode with the exception of Voice Recording mode, press the MENU button. 3072 Setup 2. Press the LEFT/ RIGHT button and select the [Setup] Language menu tab. 05 / 01/ 01 01:00 Format 3. Select the [D & Time] menu by pressing the UP/ DOWN yy/mm/dd D & Time button and press the RIGHT button. Back: Set : OK 4.
Sound If you set the operation sound to ON, various sounds will be activated for camera startup, when button are pressed, and if there is a card error, so that you can be aware of the camera operation status. Setting Operation Sounds 1. In any mode with the exception of Voice Recording mode, press the MENU button. 2. Press the LEFT/ RIGHT button and select the [Setup] menu tab. 3. Select the [Sound] menu by pressing the UP/ DOWN button and press the RIGHT button. 4.
Auto Focus lamp You can turn on and off the Auto Focus lamp How to set up the lamp 1. In any mode with the exception of Voice Recording mode, press the MENU button. 3072 Setup 2. Press the LEFT/ RIGHT button and select the [Setup] Sound menu tab. USB Off 3. Select the [AF Lamp] menu by pressing the UP/ DOWN AF Lamp On button and press the RIGHT button. Back: Set : OK 4. Select a desired sub menu by pressing the UP/ DOWN button and press the OK button. If [Off] is selected : The AF lamp will not light up.
Selecting Video out type The Video output signal from the camera can be NTSC or PAL. Your choice of output will be governed by the type of device (monitor or TV, etc.) to which the camera is connected. PAL mode can support only BDGHI. Setting the Video Out Type 1. In any mode with the exception of Voice Recording mode, press the MENU button. 2. Press the LEFT/ RIGHT button and select the [Setup] menu tab. 3. Select the [Video Out] menu by pressing the UP/ DOWN button and press the RIGHT button. 4.
Quick view If you enable Quick View before capturing an image, you can view the image you just captured on the LCD monitor for the duration set in the [Quick View] setup. Quick view is possible only with still images. Setting Quick View 1. In any mode with the exception of Voice Recording mode, press the MENU button. 3072 2. Press the LEFT/ RIGHT button and select the [Setup] Setup LCD Off menu tab. Video Out 0.5 sec 3.
Setting up the MYCAM menu You can set up a start up image, start up sound and shutter sound. Every camera working mode (with the exception of Voice recording mode) has the MyCAM menu. The items indicated by are default settings. Menu tab Main menu Sub menu Page Off LOGO User Image 1 User Image 2 Off Sound 1 Sound 2 Sound 3 Off Sound 1 Sound 2 Sound 3 S.Image p.97 p.98 S.Sound SH.Sound p.98 * Menus are subject to change without prior notice.
Start up sound You can select the sound that is activated whenever the camera is turned on. Setting the Startup Sound 1. In any mode with the exception of Voice Recording mode, press the MENU button. 2. Press the LEFT/ RIGHT button and select the [Mycam] menu tab. 3. Select the [S.Sound] menu by pressing the UP/ DOWN button and press the RIGHT button. 4. Select a desired sub menu by pressing the UP/ DOWN button and press the OK button. 5. Press the menu button twice and the menu will disappear.
Important notes Be sure to observe the following precautions! This unit contains precision electronic components. Do not use or store this unit in the following locations. - Areas exposed to severe changes in temperature and humidity. - Areas exposed to dust and dirt. - Areas exposed to direct sunlight or the inside of a vehicle in hot weather. - Environments where there is high magnetism or excessive vibration. - Areas with high explosives or highly flammable materials.
Important notes Caution on Using the Lens - If the lens is subjected to direct sunlight, it could result in discoloration and deterioration of the image sensor. - Pay attention not to get fingerprints or foreign substances on the surface of the lens. If the digital camera is not used for a long period, an electric discharge can occur. It is a good idea to remove the batteries and the memory card if you do not intend using the camera for an extended period of time.
Warning indicator There are several warnings that may appear on the LCD display. Card Error ! Memory card error Turn off the camera power and turn it on again Insert the memory card again Insert the memory card and format the memory card (p.
Warning indicator Low Light ! When taking pictures in dark places Use a tripod and take pictures in Flash Photography mode Set USB [USB] sub menu and connected device are not matched. Reconfigure [USB] in the [Setup] menu. Out Of Number When selecting too many printing pages in the PictBridge menu. Select printing page within the limitation. Before contacting a service centre Please check the following The camera doesn’t switch on There is low battery capacity. Insert charged battery.
Before contacting a service centre Camera does not take images when pressing the Shutter button There is insufficient memory capacity. Delete unnecessary image files The memory card has not been formatted Format the memory card (p.91) The memory card is exhausted Insert a new memory card The memory card is locked Refer to [Card Locked !] error message (p.101) The camera’s power is off Turn the camera power on The batteries are exhausted Insert charged battery.
Before contacting a service centre The images don't play back Incorrect file name (Violation of DCF format) Do not change the image file name Colour of image is different to the original scene White balance setting is incorrect Select appropriate White balance Images are too bright Exposure is excessive Reset exposure compensation No image on external monitor The external monitor has not been connected properly with the camera Check the connection cables There are incorrect files in the memory card Insert a
Specifications Type Effective Pixel Total Pixel Image Sensor Focal Length F No. Lens Digital Zoom Optical Viewfinder LCD Monitor Type Viewfinder Focusing Range Type Shutter Speed Control Exposure Compensation ISO Equivalent Modes Flash Range Recharging Time Sharpness Effect White Balance Voice Recording Date Imprinting Still Image Shooting Movie Clip 1/1.8" CCD Approx. 7.1 Mega-pixel Approx. 7.4 Mega-pixel Schneider Lens f = 7.8 ~ 23.4 mm (35mm film equivalent : 38 ~ 114 mm) F2.8 ~ F5.
Specifications Media File Format Image Size Storage Capacity (32MB) Image Play Type Editing Interface Power Source Dimensions (W x H x D) Weight Operating Temperature Operating Humidity Camera Driver Software Application Special Features SD : up to 1GB guaranteed (MMC Compatible) Still Image : JPEG (DCF), EXIF 2.2, DPOF 1.1, PictBridge 1.
Software Notes Please ensure that you read the instruction manual carefully before use. The attached software is a camera driver and image editing software tool for Windows. Under no circumstances should all or part of either the software or the user manual be reproduced. Copyrights for software are licensed only for use with a camera. In the unlikely event of a manufacturing fault, we will repair or exchange your camera.
About the software After inserting the software CD provided with this camera into the CD-ROM drive, the following window should automatically run. Before connecting the camera to the PC, you should first install the camera driver. Camera driver : This enables images to transfer between the camera and PC. This camera uses the USB Storage Driver as the camera driver. You can use the camera as a USB card reader.
About the software Digimax Reader : Text recognition program You can save an image file that was captured in the TEXT mode as a text file with this program. This software is only compatible with Windows. PhotoImpression : Image editing program. You can edit or store still images that you download from the camera. This software is only compatible with Windows. INFORMATION Be sure to check the system requirements before installing the driver.
Setting up the application software To use this camera with a PC, install the application software first. After this has been done, the stored images in the camera can be moved to the PC and can be edited by an image editing program. INFORMATION Close other programs before installing the application software. Before installing the application software, disconnect the USB connection. You can visit the Samsung web-site through the internet. http://www.samsungcamera.com : English http://www.samsungcamera.co.
Setting up the application software 4. If an error listed below takes place during the preview, click the [Install] button to install the XviD codec. - Only a voice plays back. - An error message displays and the movie clip does not play back. * A window shown alongside may display according to the system requirements. [Click !] 5. The XviD codec installation window will be displayed as shown alongside. Click the [Next(N)>] button. [Click !] 6. The Software License Agreement window will be displayed.
Setting up the application software 7. The XviD information window will display. Click the [Next>] button. [Click !] 8. The destination selection window will open. Click [Next >] button. To copy to the files to another folder, click [Browse...] and choose a folder you want. [Click !] 9. A window will open, asking you to choose a folder to which program icons will be added. Click [Next >] button.
Setting up the application software 11. The XviD codec is ready to install. Click the [Install] button. [Click !] 12. Installation is complete. Click the [Finish] button. [Click !] 13. A window where you can choose the program you want to install will appear. Click [Install]. For information on application software, please refer to page 108. [Click !] INFORMATION If you select [Exit] at step 13, the application program installation will be cancelled. 14. The [Digimax Viewer 2.
Setting up the application software INFORMATION If you select [Cancel] at step 14, a window for installing Digimax Reader will be displayed. 15. The Software License Agreement window will be displayed. If you agree to this, click [Yes], the window will then move to the next step. If you disagree, click [No] and the installation program will be canceled. [Click !] 16. A destination selection window will open. Click [Next >]. To copy to the files to another folder, click [Browse..
Setting up the application software 19. A window will be displayed as shown alongside. Click the [INSTALL] button. - Check the [MANUAL] button. Instructions for using Digimax reader will be displayed. - Click the [EXIT] button and Digimax reader installation will be cancelled and a window for installing PhotoImpression will be displayed. [Click !] 20. A window will open. Click the [Next(N)>] button. [Click !] 21. The Software License Agreement window will be displayed.
Setting up the application software 23. Digimax Reader Installation is completed. Click the [Finish] button and PhotoImpression installation will be started. The system will not reboot even if the [Yes, I want to restart the computer now] option is selected. [Click !] *The real frame 23 can be different with the illustration according to the system requirements. 24. The PhotoImpression installation window will be displayed as shown alongside. Click the [OK] button. [Click !] 25.
Setting up the application software 27. A destination selection window will open. Click [Next >]. To copy to the files to another folder, click [Browse...] and choose a folder you want. [Click !] 28. The [Select Components] window will appear. Click [Next >] button. [Click !] 29. A window will open, asking you to choose a folder to which program icons will be added. Click [Next >] button. If you want to add the program icons to a different folder, choose another folder, and then click [Next >] button.
Setting up the application software 31. To apply changes, you must restart the computer. Select [Yes, I want to restart my computer now], and then click [Finish]. [Click !] 32. After restarting the computer, connect the PC to the camera with the USB cable. 33. Turn the camera power on. [Found New Hardware Wizard] will open and the computer will recognise the camera. * If you have ever installed an image viewer program or your OS is Windows XP, an image viewer program will open.
Setting up the application software INFORMATION If you have installed the camera driver, [Found New Hardware Wizard] may not open. On a Windows 98 or 98 SE system, the Found New Hardware Wizard dialog box opens and a window asking you to select a driver file may appear. In this case, specify "USB Driver" in the CD supplied. (for Windows 98 and 98 SE). Before connecting the camera to the PC, You should first install the camera driver. After installing the camera driver, you have to restart your PC.
Starting PC mode If you connect the USB cable to a USB port on your PC and then turn on the power, the camera will automatically switch to "computer connection mode". In this mode, you can download stored images to your PC through the USB cable. The LCD monitor is always turned off in PC mode. The auto focus lamp will blinks when the files are transferring via the USB connection. Connecting the camera to a PC 1. Turn the PC power on. 2. Turn the camera power on. 3.
Starting PC mode Downloading stored images You can download the still images stored on the camera to your PC's hard disk and print them or use a photo editing software to edit them. 1. Connect the camera to your PC with the USB cable. 2. On your computer's desktop display, select [My computer] and double click [Removable Disk DCIM 100SSCAM]. The image files will then be displayed. 3. Select an image and press the right mouse button. 4. A pop-up menu will open. Click [Cut] or [Copy] menu.
Starting PC Mode 6. Press the right mouse button and a pop-up menu will open. Click [Paste]. 7. An image file is transferred from the camera to your PC. - By using [Digimax Viewer], you can see the stored images in the memory directly on the PC monitor and you can copy or move the image files.
Removing the USB Driver for Windows 98SE To remove the USB driver, refer to the process shown below. 1. Trace [Start Settings] and click [Control Panel]. 2. Double-click [Add/Remove programs]. 3. The [Add/Remove Programs Properties] window will open. Click [Digimax V700] and click the [Add/Remove] button. [Click !] 4. Uninstallation is complete. Click the [Finish] button and the window will disappear.
Removable Disk To use this camera as a Removable Disk, install (p.110) the USB Driver. 1. Before turning the camera power on, connect the camera to the PC with the USB cable. 2. Click [Removable Disk] under [My computer] or [Windows Explorer]. 3. Image files stored in the Removable Disk (DCIM PC. 100SSCAM) can be transferred to the INFORMATION Important information whilst using the Removable Disk The [Removable Disk] indicator will not show when the camera power is off or the USB cable is removed.
Removing the removable disk Windows 98/98SE 1. Check whether the camera and PC are transferring a file. If the auto focus lamp blinks, you have to wait until the lamp is turned off. 2. Unplug the USB cable. Windows 2000/ME/XP (The illustrations may be different from the real display in accordance with the Windows O/S.) 1. Check whether the camera and PC are transferring a file. If the auto focus lamp blinks, you have to wait until the lamp is turned off. 2.
Removing the removable disk 6. A [Unplug or Eject Hardware] window will open. Click the [Close] button and the removable disk will be removed safely. 7. Unplug the USB cable. [Click!] Setting up the USB Driver for MAC 1. A USB Driver for MAC is not included with the software CD as MAC OS supports the camera driver. 2. Check the MAC OS. You can check the MAC OS version during MAC OS start-up. This camera is compatible with MAC OS 9.2 ~ 10.3. 3.
Digimax Viewer 2.1 This software is only compatible with Windows. 1. To open Digimax Viewer, click the [Start Programs Samsung Digimax Viewer 2.1 Digimax Viewer 2.1 ] and Digimax Viewer 2.1 will then open. 2. If the [Auto Launch] option is selected, this program will be executed automatically with recognizing the camera. 3. You can easily use the Digimax viewer 2.1 program as it offers a FILE menu and TOOL bar.And, you can use the pop up menu. Click an image and press the right mouse button.
Digimax Reader Digimax Reader is a Text recognition program. You can save an image file that is captured in the Text mode, as a text file with this program. This software is only compatible with Windows. To start the program, click [Start The following screen will appear. Programs Digimax Reader Eng]. How to use the Digimax Reader 1. Connect the camera and the PC with a USB cable and download the images that were stored in the camera to the PC.
Digimax Reader 4. Select the image you want to save as a text file. * Only an image that was taken with SAMSUNG camera can be opened. 5. Click the Area Analysis( image. ) icon to scan the 6. Part of the image you selected will be displayed as shown. 7. Click the Character Recognition( ) icon. The part selected in the previous step will be recognized as text. 8. To save the section as a text, click the Save( icon. A window as shown alongside will be displayed.
Digimax Reader 9. Select a file type that you want to. Selectable file type : *.TXT, *.HWP, *.DOC, *.RTF INFORMATION To get an image that can be recognized as a text : - Keep a distance of 20cm between the subject and the camera. - The subject need to be centered. - Avoid the camera shake to get a good image. Refer to the [Help] menu in Digimax Reader for further information. Using PhotoImpression With PhotoImpression, you can edit or store still images that you downloaded from the camera.
Using PhotoImpression You can use PhotoImpression to perform the following tasks. Command Button Button Description Imports a picture from an album, a source folder, or the camera/scanner, or captures screen shots of what is being viewed on the current monitor. Selects Cut, Resize, Edit Image, Insert Text, Enhance Picture, Insert Effects, or Layer. Performs Insert Frame, Insert Borders, Insert Calendar, Insert Greeting Cards, Insert Template, or Connect with Other Software.
FAQ Please check the following if the USB connection malfunctions. [Case 1] The camera power is off. Turn the camera power on. We recommend using an AC power adapter in PC mode. [Case 2] USB Driver is not installed correctly. Install the USB Driver correctly. Refer to page 110. [Case 3] The USB cable is not connected or you are using a cable with an incorrect specification. Use a USB cable with the correct specification. [Case 4] The camera is not recognized by your PC.
FAQ There must be USB Host Controller and USB root hub under [Universal Serial Bus controllers]. In addition, double-click on the USB Universal Host Controller and the USB Root Hub to check if the Device Status states "This device is working properly". If the Device Status says the device is "not working properly", click the "Driver" tab and then click [Update Driver] or [Reinstall Driver]. When all the conditions mentioned above are met, the computer can support the USB interface.
FAQ When the movie clip doesn t play back on the PC When the movie clip recorded by the camera doesn t play back on the PC, the causes are mostly codec installed on the PC. When A codec for play back the movie clip isn t installed Install the codec as listed below. [Installing a codec for Windows] 1) Insert the CD provided with the camera 2) Run the windows explorer and select [CD-ROM drive:\Xvid] folder and click the Xvid1.0.2.exe file.
FAQ If a PC (Windows 98) stops responding while the camera and PC are connected repeatedly If a PC (Windows 98) is turned on for a long time and connect the camera repeatedly, the PC may not recognise the camera. In this case, re-start the PC. If a PC connected with the camera stops responding while the Windows is starting. In this case, disconnect the PC and the camera and the windows will start correctly. If the problem happens continuously, set the Legacy USB Support to disable and re-start the PC.
SAMSUNG TECHWIN CO., LTD. OPTICS & DIGITAL IMAGING DIVISION 145-3, SANGDAEWON 1-DONG, JUNGWONGU, SUNGNAM-CITY, KYUNGKI-DO, KOREA 462-121 TEL : (82) 31-740-8086,8088, 8090, 8092, 8099 FAX : (82) 31-740-8398, 8111 www.samsungcamera.com SAMSUNG OPTO-ELECTRONICS AMERICA, INC. HEADQUARTERS 40 SEAVIEW DRIVE, SECAUCUS, NJ07094, U.S.A. TEL : (1) 201-902-0347 FAX : (1) 201-902-9342 WESTERN REGIONAL OFFICE 18600 BROADWICK ST., RANCHO DOMINGUEZ, CA 90220, U.S.A. TEL : (1) 310-900-5263/5264 FAX : (1) 310-537-1566 www.
