User’s Manual Thank you for buying a Samsung Camera. This manual will guide you through using the camera and MP3 player, including capturing images, downloading images, playing music and using the application software.
Instructions ■ Use this camera in the following order Set up the camera driver Before connecting the camera to a PC, via the USB cable, you will need to set up the camera driver. Install the camera driver that is contained in Application software CD-ROM. (p.127) Take a picture. (p.23) Take a picture Insert the USB cable Check the camera’s power Check [Removable Disk] Insert the supplied USB cable into the PC’s USB port and the camera’s USB connection terminal. (p.136) Check the camera’s power.
Contents ●Voice memo/ UP button READY ●Getting to know your camera ●Danger/ Warning ●Caution/ An FCC warning ●System chart ●Identification of features ●Cradle ●Connecting to a Power Source ■Using the SAC-41 ■How to charge the rechargeable battery (SLB-0737) with the SAC-41 ■Important information about battery (SLB-0737) charging with the SAC-41 ■Using the battery/ Removing the battery ●Instructions on how to use the memory card ●Inserting the memory card ●Removing the memory card ●When Using the Camera for
Contents ●Play & Pause/ Down button 70 ●Delete button 70 ●Left/ Right/ Menu/ OK button 71 ●Album button 72 ●Setting up the play back function using the LCD monitor 75 ●Starting the slide show 78 ●Protecting images 80 ●Deleting images 81 ●Resize 82 ●Effect 83 ●Rotating an image/ DPOF 84 ●Copy To Card 87 ●LCD monitor indicator for MP3 mode 109 ●Using the camera buttons to adjust the camera 110 ●Playlist button 110 ●Hold button 111 ●Volume button 112 ●Control button 112 ●Delete button 112 ●Setting up the play
Getting to know your camera Thank you for buying a Samsung Digital Camera. ● Prior to using this camera, please read the user manual thoroughly. ● When you require After Sales service, please bring the camera and the cause of the camera malfunction (such as battery, Memory card etc.) to the A/S centre. ● Please check that the camera is operating properly prior to when you intend to use it (e.g. for a trip or an important event) to avoid disappointment.
Danger ■ Do not attempt to modify this camera in any way. This may result in fire, injury, electric shock or severe damage to you or your camera. Internal inspection, maintenance and repairs should be carried out by your dealer or Samsung Camera Service centre. ■ Please do not use this product in close proximity to flammable or explosive gases, as this could increase the risk of explosion. ■ Should any form of liquid or a foreign object enter the camera, do not use it.
Caution ■ Leaking, overheating, or burst battery could result in fire or injury. •Use battery with the correct specification for the camera. •Do not short circuit, heat or dispose of battery in fire. •Do not insert the battery with the reverse polarities. ■ Remove the battery when not planning to use the camera for a long period of time. Battery may leak corrosive electrolyte and permanently damage the camera’s components. ■ Do not fire the flash while it is in contact with hands or objects.
System chart Please check that you have the correct contents before using this product. The contents can vary depending on the sales region. To buy the optional equipment, contact your nearest Samsung dealer or Samsung service centre. < Included items > Camera case DPOF compatible printer (see p.84) AC cord AC cord User manual, Product warranty Camera strap Software CD (see p.125, 126) SD memory card/MMC (see p.
System chart System Requirements For Windows Computer USB cable PictBridge compatible printer(see p.89) AV cable •Windows 98/ 98SE/ 2000/ ME/ XP •PC with processor better than Pentium II 450MHz (Pentium 700MHz or better is recommended) •200MB of available hard-disk space (Over 1GB is recommended) •Minimum 64MB RAM (XP : 128MB) •1024x768 pixels, 16-bit colour display compatible monitor (24-bit colour display recommended) •DirectX 9.
Identification of features Front & Top SF mode button/ Hold button Shutter button Microphone Power button Flash Speaker Self-timer lamp/ Auto Focus lamp Optical 3X zoom lens/ Lens cover ※ Take care not to press the lens, lens cover and camera by force. This may cause the camera malfunction. Back & Bottom Zoom W button (Thumbnail, Vol. Down) M(Mode/Album) button Zoom T button (Digital zoom, Vol.
Identification of features Bottom / 5-function button Memory card slot Voice memo/ UP button MENU/ OK button FLASH/ LEFT button SELF-TIMER/ RIGHT button Battery chamber Battery holder Battery chamber cover Macro/ DOWN button Play & Pause button Cradle ■ You can recharge your rechargeable battery, transfer a captured image to print, and download images with the cradle.
Identification of features ■ Self-timer lamp Icon Status Description Blinking For the 2 seconds, the lamp blinks quickly at 0.25-second intervals. Blinking For the final 2 seconds, the lamp blinks quickly at 0.25-second For the first 8 seconds, the lamp blinks at 1 second intervals. intervals. Blinking A picture will be taken after about 10 seconds and 2 seconds later a second picture will be taken.
Connecting to a Power Source ■ You should use the rechargeable battery (SLB-0737) supplied with the camera. Be sure to charge the battery before using the camera. ■ SLB-0737 rechargeable battery Specification Model SLB-0737 Type Lithium Ion Capacity 760mAh Voltage 3.7V Charging time Approx. 150 MIN (Using the SAC-41) ■ Number of images and battery life Still image Movie MP3 Battery life Number of images Recording time Playing time Approx. 75 MIN Approx. 150 Approx.65 MIN About 240 min.
Connecting to a Power Source Using the SAC-41 If you have access to a mains supply, using an SAC-41 allows the camera to be used for long periods of time. Plug the SAC-41 into the DC connection terminal on the camera or cradle. Before turning on the camera power with an SAC-41, insert the rechargeable battery that was charged for over 10 minutes with turning off the camera. DANGER ● Always turn off the power before taking the SAC-41 out of the mains supply.
Connecting to a Power Source ■ How to charge the rechargeable battery (SLB-0737) with the SAC-41. ● Charging with the camera 1. Insert the rechargeable battery into the battery chamber. 2. Put the SAC-41 into your power socket and DC connection terminal of the camera.
Connecting to a Power Source ■ Charging LED of the SAC-41 Status Using the cradle Direct to the camera Being Charged Red LED is on Red LED is on Charging is complete Green LED is on Green LED is on Charging error Red LED is off or blinking Red LED is off or blinking ● If there is a charging error, please check all the power connections are in place. ● A USB cable for transmitting data can’t be used for charging the rechargeable battery. ● A USB cable for recharging the battery is optional.
Connecting to a Power Source Using the battery : If the camera does not turn on after you have inserted battery, please check whether the battery are inserted with the correct polarity(+/-). 1. Open the battery chamber cover by pushing in the direction of the arrow. 2. Insert the battery taking note of the polarity (+ / -). 3. To close the battery chamber cover, push it until it clicks. Removing the battery 1. Turn off the camera power. Open the battery chamber cover and move the battery holder aside.
Instructions on how to use the memory card ● Be sure to format the memory card (see p.97) if you are using a newly purchased memory for the first time, if it contains data that the camera cannot recognise, or if it contains images captured with a different camera. ● Turn off the camera power whenever the memory card is being inserted or removed. ● Repeated use of the memory card will eventually reduce the memory card’s performance. Should this be the case, you will need to purchase a new memory card.
Instructions on how to use the memory card INFORMATION ● Don't remove the memory card when the camera status lamp is blinking as this may cause damage to data in the memory card. ■ The camera can use SD Memory Cards and MMC (Multi Media Cards). Please consult the enclosed manual for using the MMC Cards. The SD memory card has a write protect switch that prevents image files from being deleted or formatted. By sliding the switch to the bottom of the SD memory card, the data will be protected.
Inserting the memory card 1. Turn off the camera’s power and pull the battery chamber cover in the direction of the arrow to open. 2. Have the front of the memory card facing toward the front of the camera (lens) and the card pins toward the back of the camera (LCD monitor), and then push the memory card into the card slot until you hear a click. 3. To close, push the battery chamber cover until you hear a click. If the memory card does not slide in smoothly, do not attempt to insert it by force.
When Using the Camera for the First Time ■ Charge the rechargeable battery fully before using the camera for the first time. ■ When the camera is turned on for the first time, a menu will be displayed to set date, time and language in the LCD monitor. This menu will not be displayed after setting up the date, time and language. Set up the date, time and language before using this camera. ● Setting up the date, time and date type 1.
LCD monitor indicator ■ The LCD monitor displays information about the shooting functions and selections. ⑳ ① ⑲ ② ⑱ ③ ⑰ ④ ⑯ ⑤ ⑮ ⑥ ⑭ ⑦ ⑬ ⑧ ⑫ ⑨ ⑩ ⑪ [Image & Full Status] No. Description 1 Recording mode Icons Page p.49 2 Battery p.17 3 Continuous shot p.52 4 Flash p.36 5 Self-timer p.38 6 Macro p.33 7 Metering p.52 8 Card inserted indicator - 9 Auto focus frame - 10 Camera shake warning p.29 11 Date/ Time 12 Exposure compensation p.
LCD monitor indicator 15 RGB 16 Sharpness p.53 17 Image quality/ Frame rate p.51 18 Image size p.50 19 RGB Number of available shots remaining 38 Remaining time (Movie clip/ Voice recording) 00:01:30/ 01:00:00 p.42 p.19 20 Voice memo/ Mic. off p.32/26 21 Optical/ Digital Zoom bar/ Digital Zoom rate p.31 Changing the recording mode ■ You can select the desired working mode using the M (Mode) button located on the back of the camera and then the [Mode], [Mode set] menu.
Changing the recording mode ● Changing the recording mode : If the [Still/ Movie/ MP3] menu was selected Steps from 1-4 are the same as those for selecting the [Mode] menu. 5. A recording mode used just before will display. 6. Press the M (Mode) button located on the back of the camera and the recording mode will change to the movie clip mode. 7. Press the M (Mode) button twice and a still image mode selected on the [Mode set] menu will be selected.
Starting the recording mode ■ How to use the Auto mode Use this for shooting basic still images. 1. Select the [Full] sub menu on the [Mode] menu (p.23). 2. Select the Auto mode by pressing the M (Mode) button (p.24). 3. Point the camera towards the subject and compose the image by using the LCD monitor. 4. Press the shutter button to capture an image.
Starting the recording mode ■ Recording the movie clip without voice You can record the movie clip without voice. Steps from 1-3 are the same as those for MOVIE CLIP mode. 4. Press the Up button and the ( ) icon will display on the LCD monitor. 5. Press the shutter button and movie clip is recorded for as long as the available recording time without voice. 6. To stop the recording, press the shutter button again.
Starting the recording mode ■ How to use the Scene modes Use the menu to easily configure optimal settings for a variety of shooting situations. 1. Select the [Full] sub menu on the [Mode] menu (p.23). 2. Select the Scene mode by pressing the M (Mode) button (p.24). 3. Point the camera towards the subject and compose the image by using the LCD monitor. 4. Press the shutter button to capture an image. [SCENE mode] ※ The scene modes are listed below.
Starting the recording mode ■ How to use the VOICE RECORDING mode A voice recording can be recorded for as long as the available recording time of the memory capacity allows. (Max: 1 hour) 1. Select the [Full] sub menu on the [Mode] menu (p.23). 2. Select the Voice Recording mode by pressing the M (Mode) button (p.24). 3. Press the shutter button to record a voice. - Press the shutter button once and voice is recorded for as long as the available recording time (Max : 1 hour) allows.
Things to Watch Out for When Taking Pictures ■ Pressing the shutter button down half way Lightly press the shutter button to confirm focus and flash battery charge. Press the shutter button all way down to take the picture. [ Lightly press the shutter button ] [ Press the shutter button ] ■ The available recording time may vary depending on shooting conditions and camera settings.
Using the camera buttons to adjust the camera ■ The recording mode function can be set up by using the camera buttons. POWER button ● Used for turning the camera’s power on / off. ● If there is no operation during the specified time, the camera's power will be turned off automatically to save battery life. Refer to page 96 for more information about the auto power off function. SHUTTER button ● Used for taking an image or recording voice in the recording mode.
ZOOM W/ T button ■ This camera has a 3X optical zoom and a 5X digital zoom function. Using both will offer a total zoom ratio of 15X. ● TELE Zoom Optical zoom TELE Digital zoom TELE : Pressing the ZOOM T button. This will zoom into the subject i.e. the subject will appear nearer. : When the maximum (3X) optical zoom is selected, pressing the ZOOM T button activates the digital zoom software. Releasing ZOOM T button stops the digital zoom at the required setting.
ZOOM W/ T button INFORMATION ● Images taken using the digital zoom may take a little longer for the camera to process. Allow time for this to take place. ● The digital zoom cannot be used in movie clip shots. ● If the Zoom buttons are being pressed during the Movie clip shots, the voice will not recorded. ● You may notice a decrease in image quality when using the digital zoom.
Voice memo( )/ UP button 3. Press the shutter button and take a picture. The picture is stored on the memory. 4. Voice memo will be recorded for ten seconds from the moment the picture is stored. In the middle of the voice recording, pressing the shutter button will stop the voice memo. [Recording Voice Memo] INFORMATION ● A distance of 40cm between you and the camera (microphone) is the best distance to record sound.
Macro( )/ Down button ■ Types of focus modes and focus ranges (W: Wide, T: Tele) Auto ( Mode Focus Type Focus range Super macro ( ) Focus range ) Auto macro( ) Manual ( Super macro( W : 1~5 (Wide only) ) Macro( Normal W : 50~Infinity T : 50~Infinity W : 5~Infinity T : 50~Infinity W : 1~5 (Wide only) Mode Focus Type (Unit : cm) ) ) W : 5~50 T : 25~50 Normal W : 50~Infinity T : 50~Infinity ※ See the next page for the available focusing method, by recording mode.
Macro( )/ Down button ■ Available focusing method, by recording mode ( O: Selectable , X: Not selectable, ∞: Infinity focus range) Mode Auto macro X O X O Super macro X O O X macro O X O X Normal O O O X SCENE Mode Auto macro X X X X X O X X X X X Super macro X X X X X X X X X X X macro X X X X O X X X X X X Normal O O O ∞ X X ∞ ∞ O ∞ O Focus lock ■ To focus on the subject positioned outside of the centre, use the focus lock function.
Flash ( )/ Left button ■ When the menu is displayed on the LCD monitor, pressing the LEFT button makes the cursor shift to the left tab. ■ When the menu is not displayed on the LCD monitor, the LEFT button operates as the FLASH ( ) button. ● Selecting the flash mode 1. Press the M (Mode) button to select a Recording mode [Selecting the Auto flash] with the exception of Movie clip mode and the Voice Recording mode (p.24). 2.
Flash ( )/ Left button ● Flash mode indicator Menu tab Flash mode Description Auto flash If the subject or background is dark, the camera flash will operate automatically. Auto & Red eye reduction If a subject or background is dark, the camera flash will work automatically and will reduce the red-eye effect by using the redeye reduction function. Fill in flash The flash fires regardless of available light. The intensity of the flash will be controlled, according to the prevailing conditions.
Self-timer ( )/ Right button ■ When the menu is displayed on the LCD monitor, pressing the Right button makes the cursor shift to the right tab. The right button can also be used to move to a sub menu to select a different setting. When the menu is not displayed on the LCD monitor, the RIGHT button operates as the Self-timer. This function is used when the photographer would also like to be in the image. ● Using the self-timer 1.
MENU/ OK button ■ MENU button - When you press the MENU button, a menu related to each camera mode will be displayed on the LCD monitor. Pressing it again will return the LCD to the initial display. - A menu option can be displayed when the following are selected : MOVIE CLIP and STILL IMAGE mode. There is no menu available when the VOICE RECORDING mode is selected.
M (Mode) button ● How to use the mode button : In case of [Full] sub menu and Auto mode [Auto mode] Pressing the Mode button Manual Pressing the Right button Set : OK/M [Manual mode] Auto Set : OK/M [Mode selection menu] Movie Pressing the Left button Set : OK/M [Movie clip mode] Pressing the Up button Night Portrait Pressing the Left/ Right button Set : OK/M Set : OK/M [Scene mode] [Selecting a scene mode] ※ Press the Mode button and the mode selection menu will disappear.
SF button ■ Pressing the SF button selects the SF(Safety Flash) mode In poor indoor light conditions, Safety Flash will help you get a good image without the use of a flash. As children are sensitive of using flash, this is suitable function for taking children. ● Things to watch out for using the SF mode 1. The SF range is 2m(WIDE) and 1.5m(TELE). 2. The digital zoom will not operate in the SF mode. 3. If the lighting conditions are brighter than fluorescent lighting condition, the SF doesn’t activate. 4.
+/- button ■ You can use the +/- button to adjust the values for the RGB, ISO, white balance, exposure compensation and Long Time shutter speed. ■ When the SF is selected, ISO value is fixed as AUTO and Exposure value is fixed as 0.0EV. Main menu Sub menu RGB R (Red), G (Green), B (Blue) ISO AUTO, 100, 200, 400 WHITE BALANCE AUTO, DAYLIGHT, CLOUDY, FLUORESCENT H, FLUORESCENT L, TUNGSTEN, CUSTOM. Exposure compensation -2.0 ~ 0.0 ~ +2.0 (0.
+/- button ■ ISO : You can select the ISO sensitivity when taking pictures. The speed or specific light-sensitivity of a camera is rated by ISO numbers. ● Selecting an ISO Sensitivity 1. Press the +/- button, and then use the UP and DOWN buttons to select the ISO icon( ). The ISO menu bar will appear as shown. 2. Use the LEFT and RIGHT buttons to select the desired ISO sensitivity value. - AUTO : The camera's sensitivity is automatically changed by variables such as lighting value or subject brightness.
+/- button ● Using the Custom White Balance White balance settings may vary slightly depending on the shooting environment. You can select the most appropriate white balance setting for a given shooting environment by setting up the custom white balance. 1. Select the CUSTOM ( ) menu of the White Balance. 2. Place a sheet of white paper in front of the camera so that the LCD monitor shows only white, and then press the SHUTTER button. 3. Your custom white balance value is stored.
+/- button ■ Long Time shutter : This camera automatically adjusts the shutter speed and aperture values to the shooting environment. However, in NIGHT SCENE mode, you can set the shutter speed and aperture values to your preference. ● Adjusting the shutter speed and aperture values 1. Select the [Night] scene mode. (M button → [Scene] → [Night]) 2. Press +/- button and Long Time shutter menu (LT, For selecting shutter speed and aperture value) will be displayed. 3.
Using the LCD monitor to adjust the camera settings ■ You can use the menu on the LCD monitor to set up recording functions. In any mode with the exception of VOICE RECORDING mode, pressing the MENU button displays the menu on the LCD monitor. INFORMATION ● The menu will not be displayed on the LCD monitor in the following circumstances: - When another button is being operated. - While image data is being processed. - When there is no battery capacity.
Using the LCD monitor to adjust the camera settings Menu tab Main menu Sub menu Camera working mode Page Frame Rate 30fps 15fps p.51 Metering Multi Spot p.52 Shooting Single Continuous p.52 Soft Normal Vivid - Full OSD Basic OSD Save Mode - Normal Red B&W Green Sepia Blue Negative - Off Range 1 ~ 4 Off 2~4 Parts Pano. 2 Parts - Photo Frame Off Frame 1 ~ 9 p.59 Stabilizer Off On p.60 p.53 Sharpness OSD Information p.53 p.54 Effect Highlight Composite p.
How to use the menu 1. Turn on the camera and press the MENU button. A menu for each camera mode appears. However, there is no menu for Voice Recording mode ( ). 2. Use the LEFT and RIGHT buttons to navigate through the menus. Mode Set Auto Press the LEFT or RIGHT button. Manual Press the LEFT or RIGHT button. Mode Still/ Movie/ MP3 Size 2592 X 1944 2272 X 1704 2048 X 1536 1600 X 1200 1024 X 768 640 X 480 Full Movie Night portrait Children 3. Use the UP and DOWN buttons to select a sub menu.
Mode Set ■ You can select the desired recording mode. [Auto] [Manual] : For shooting basic still image : You can still manually configure all Mode Set Auto functions except the aperture value and Manual shutter speed. Movie Night [Movie] : For taking a movie clip portrait [Night] : Use this for shooting still images at night Children or in other dark conditions. [Portrait] : To take a picture of a person. [Children] : To take a picture of fast moving objects, for example, children.
Size ■ You can select the image size appropriate for your application.
Quality/ Frame rate ■ You can select the compression ratio appropriate for your application of the captured images. The higher the compression ratio, the lower the picture quality. Mode STILL IMAGE mode MOVIE CLIP mode Icon Sub menu S. Fine Fine Normal 30FPS 15FPS File Format jpeg jpeg jpeg avi avi Frame Rate Quality S.Fine 30 FPS Fine 15 FPS Normal [ STILL IMAGE mode ] [ MOVIE CLIP mode ] INFORMATION ● S. Fine is the highest quality and Normal is the lowest setting.
Metering ■ If you cannot obtain suitable exposure conditions, you can change the metering method to take brighter pictures. [Multi] ( ) [Spot] ( ) : Exposure will be calculated based on an average of the available light in the image Metering area. However, the calculation will be Multi Spot biased towards the centre of the image area. This is suitable for general use. : Only the rectangular area in the centre of the LCD monitor will be metered for [STILL IMAGE mode] light.
Sharpness ■ You can adjust the sharpness of the picture you want to take. You cannot check the sharpness effect on the LCD monitor before you take a picture, because this function is applied only when the captured image is stored on the memory. Sub menu Icon Sharpness Soft Normal Vivid Description The edges of the image are softened. Soft This effect is suitable for editing images on your PC. The edges of the image are sharp. Normal This is suitable for printing. The edges of the image are emphasized.
Effect ■ By using the camera’s digital processor, it is possible to add special effects to your images. Effect Effect Normal Normal B&W Sepia Red Green Blue B&W Sepia Red Green Blue [MANUAL mode] [Normal] [B & W] [Sepia] [ MOVIE CLIP mode] : No effect is added to the image. : Captured images will be stored in black and white. : Captured images will be stored in a sepia tone (a gradient of yellowish brown colours). [Red] : Captured images will be stored in a red tone.
Special Effect ■ By using the camera’s digital processor, it is possible to add special effects to your images. You can select this menu only in the MANUAL mode. ■ You can select the preset focus frame, Composite shooting and Photo frame function. If a special effect is selected, the rest special functions set before are cancelled automatically. ■ Even if the camera is turned off, the special effect setting will be preserved. To cancel the special effect, select the [Off] sub menu of each menu.
Special Effect : Preset focus frames ● Moving and changing the focus frame You can change the focus frame after selecting a Range menu. 1. Point the camera towards the subject and compose the image by using the LCD monitor. 2. Press the +/- button. 3. The colour of focus frame turns white. Press the Up/Down/Left/Right button to moves the focus frame position. 4. To select the focus frame position, press the +/- button again and you can take a picture.
Special Effect : Composite shooting ■ You can combine 2 ~ 4 different shots in a still image. 1. Select the MANUAL mode, and press the menu button. 2. Press the LEFT/ RIGHT button and select the Special Effect [Special Effect] menu tab. HighLight Off Composite 2 Parts 3. Select the [Composite] menu by pressing the UP/ DOWN Photo Frame 3 Parts button and press the Right button. 4 Parts PANO.2 Part 4. Select a desired sub menu by pressing the UP/ DOWN Back:◀ Set:OK button and press the OK button.
Special Effect : Composite shooting ● Changing a part of composite shot before taking the last shot Before taking the last composite shot, you can change a part of composite shot. 1. During the composite shots, press the +/- button. 2. A previous image will be deleted and new frame will display. If there is an image taken before, press the +/- button again and a previous image will be deleted again.
Special Effect : Photo Frame ■ You can add 9 types of frame-like borders to a still image you want to capture. ■ Date & Time information will not be printed on the stored image taken with [Photo Frame] menu. 1. Select the MANUAL mode, and press the menu button. 2. Press the LEFT/ RIGHT button and select the [Special Effect] menu tab. 3. Select the [Photo Frame] menu by pressing the UP/ DOWN button and press the Right button. 4.
Movie Clip frame stabiliser ■ This function helps stabilize images captured during movie recording. You can select this menu only in the MOVIE CLIP mode. If the memory card is not inserted, this function will not operate. ● How to use this function 1. Select the MOVIE CLIP mode by pressing the M (Mode) button and press the menu button. Press the Left/ Right Stabilizer Off button to select the [Stabilizer] menu. On 2. Select a desired sub menu by pressing the Up/Down button and press the OK button.
Starting play mode ■ Turn the camera on and select Play mode by pressing the play mode button ( The camera can now play back the images stored in the memory. ). ■ You can set up the PLAY mode function by using the camera buttons and LCD monitor. ■ If the memory card is inserted in the camera, all the camera functions apply only to the memory card. ■ If the memory card is not inserted in the camera, all the camera functions apply only to the internal memory. ● Playing back a still image 1.
Starting play mode ● Playing back a movie clip Steps from 1-2 are the same as those to play back a still image. 3. Select the recorded movie clip that you want to play back by using the LEFT/RIGHT button. If you select a movie clip, the movie clip indicator ( ) will be displayed on the LCD monitor. 4. Press the play & pause button ( ) to play back a movie clip file. - To pause a movie clip file while playing it back, press the play & pause button again.
Starting play mode ■ On camera movie trimming : You can extract desired frames of movie clip during the movie clip play back. ● If the running time is under 10 seconds, the movie clip can’t be trimmed. 1. Select a desired movie clip in the play mode. 2. Play back the movie clip by pressing the Play & Pause button. 3. Press the Pause button at the point of the movie clip that you want to start extracting. 4. Press the T button.
Starting play mode ● Playing back a recorded voice Steps from 1-2 are the same as those to play back a still image. 3. Select the recorded voice that you want to play back by using the LEFT/ RIGHT button. If you select a recorded voice file, the voice indicator ( ) will be displayed on the LCD monitor. 4. Press the play & pause button ( ) to play back a recorded voice file. - To pause a recorded voice file, while playing it back, press the play & pause button again.
LCD monitor indicator ■ The LCD monitor displays shooting information about the displayed image. ⑦ ⑧ ① ② ③ ④ ⑤ ⑥ No. Description Icon Page 1 Play mode - 2 Battery p.17 3 File Type - 4 Voice memo p.69 5 Protect indicator p.80 6 DPOF indicator p.84 7 Folder name and Stored image number 8 Volume display 100-0009 p.68 ■ Shooting information is displayed as follows. Size Av Tv ISO Flash Date : : : : : : 2592X1944 F3.
Using the camera buttons to adjust the camera ■ In Play mode, you can use the buttons on the camera to conveniently set up the Play mode functions. Play mode button ■ If you have turned on the camera by pressing the POWER button, you can press the PLAY MODE button once to switch to Play mode and press it again to switch to Recording mode. ■ You can turn the power on with the play mode button. The camera is turned on in play mode. Press the play mode button (Under 1 Sec.) again to turn off the camera.
Thumbnail( )/ Enlargement( ) button/ Volume button( ) ■ You can view multiple pictures, enlarge a selected picture, and crop and save a selected area of an image. ■ When a movie clip, voice memo or voice recording file is playing back, you can control the volume of those files using this button. ● Thumbnail display 1. While an image is displayed full screen, press the thumbnail button. 2. The thumbnail display will highlight the image that had been showing at the time the thumbnail mode was selected. 3.
Thumbnail( )/ Enlargement( ) button/ Volume button( ) ● The maximum enlargement rate in proportion to the image size. Image size 2592 2272 2048 1600 1024 640 Maximum enlargement rate X10.1 X8.8 X8.0 X6.2 X4.0 X2.5 ● Trimming : You can extract part of the image that you want and save it separately. 1. Select an image that you want to enlarge and press the enlargement button. 2. Different parts of the image can be viewed by pressing the Trimming? Trimming 5 function button. Cancel 3.
Voice ( ) memo/ Up button ■ When the menu is displayed on the LCD monitor, pressing the UP button makes the menu cursor move up. ■ When the menu is not displayed on the LCD monitor, the UP button operates as the voice memo button. You can add your voice to a stored still image. ● Adding a Voice Memo to a Still Image 1. Press the LEFT/ RIGHT button to select an image that you wish to add sound to. 2. Press the voice memo button ( ) and the voice memo indicator will display.
Play & Pause ( )/ Down button ■ In Play mode, the play & pause/ down button works as follows: - If the menu is displayed Press the DOWN button to move from the main menu to a sub menu, or to move down the sub menu cursor. - If a still image with a voice memo, a voice file, or a movie clip is playing In Stop mode : Plays a still image with a voice memo, a voice file, or a movie clip. During playback : Temporarily stops playback.
Delete ( ) button ● Deleting Images in Thumbnail Display Mode 1. Use the UP, DOWN, LEFT, and RIGHT buttons to select the image you want to delete, and then press the DELETE ( ) button. 2. The following message will be displayed on the LCD monitor. 3. Select the submenu values by pressing the UP/ DOWN button and then press the OK button. If [Delete] is selected : deletes the selected images. If [Cancel] is selected : cancels "Delete Image". Press the DELETE button.
Album button ■ You can organise the captured still images into albums by using the Album button. ■ This camera has 8 albums and each album can take up to 100 images. ■ The album menu loading time depends on the memory card type. ■ How to use the album ● Selecting the album 1. In the play mode, press the Album button. 2. Select the [Select] menu by pressing the Up/ Down button and press the Right button. Select Slide Add Remove Exit:MENU 3.
Album button 3. Select the still images you wish to add by pressing the Up/Down/Left/Right buttons and press the Zoom T button. marks are displayed on the selected images. ※ To cancel the selection, press the Zoom T button again. Select Slide Add Remove Select:T 4. Press the OK button and a confirmation window will display. Select a desired sub menu by pressing the UP/ DOWN button and press the OK button. - [Add] : Inserts the selected images into the album. - [Cancel] : Cancels the inserting images.
Album button ● Playing back the albums ◎ Playing back all of the albums 1. Select [All] menu and press the OK button. All of the albums will be selected. 2. Select [Slide] menu by pressing the Up/ Down button and press the Right button. ※ You can select [Start], [Interval], [Repeat] and [Effect] menus. - [Start] : Start the slide show - [Interval] : Set the slide show play interval - [Repeat] : Choose to repeat the slide show after finishing the first cycle.
Setting up the play back function using the LCD monitor ■ PLAY mode functions can be changed by using the LCD monitor. In the PLAY mode, pressing the MENU button displays the menu on the LCD monitor. The menus you can set up in Play mode are as follows. To capture an image after setting up the play menu, press the PLAY mode button or shutter button.
Setting up the play back function using the LCD monitor Menu tab Main menu Copy to Card OSD Information Sub menu Secondary menu No - Yes - Full OSD - OSD Off - Page p.87 p.88 ■ This menu is available while the camera is connected to a PictBridge supporting printer (direct connection to the camera, sold separately) with a USB cable. Menu tab Main menu Images Auto Set Sub menu Secondary menu One Pic - All Pics - No - Yes - Page p.90 p.
Setting up the play back function using the LCD monitor Menu tab Main menu Sub menu Secondary menu Page Auto Type Plain Photo Fastphoto Auto Quality Custom Set Draft Normal Fine p.91 Auto Date Off On Auto File Name Off On Print DPOF Print Reset Standard - Index - No - Yes - No - Yes - p.92 p.92 p.93 ※ Menus are subject to change without prior notice.
Starting the slide show ■ Images can be displayed continuously at pre-set intervals. You can view the slide show by connecting the camera to an external monitor. 1. Press the play mode button and press the menu button. 2. Press the LEFT/ RIGHT button and select the [Slide] menu tab. ● Start the slide show : The slide show can start only in the [Start] menu. 1. Use the Up/Down buttons to select the [Start] menu. 2. Press the OK button to start the slide show.
Starting the slide show ● Configure slide show effects: Unique screen effects can be used for the slide show. 1. Select the [Effect] sub menu by pressing the UP/ DOWN button and press the RIGHT button. Slide 2. Use the Up/ Down Button to select the type of effect. Start Cancel Interval Effect 1 [Cancel] : Normal display. Repeat Effect 2 Effect Effect 3 [Effect 1] : Image is displayed slowly. Effect 4 [Effect 2] : Image is displayed slowly from the centre Back:◀ Set:OK outwards.
Protecting images ■ This is used to protect specific shots from being accidentally erased (Lock). It also unprotects images that have been previously protected (Unlock). ● Protecting Images 1. Press the play mode button and press the menu button. 2. Press the LEFT/ RIGHT button and select the [Protect] menu tab. 3. Select a desired sub menu by pressing the UP/ DOWN button and press the OK button. [Select ] : Selection window for an image to be protected/released is displayed.
Deleting images ■ Of all the files stored in the memory card, the unprotected files in the DCIM subfolder will be deleted. Remember that this will permanently delete unprotected images. Important shots should be stored on a computer before deletion takes place. The startup image is stored in the camera's internal memory (i.e., not on the memory card) and it will not be deleted even if you delete all files on the memory card. ● Deleting images 1. Press the play mode button and press the menu button. 2.
Resize ■ Change the resolution (size) of pictures taken. Select [User image] to save an image to be the start-up image. The resized image will have a new file name. 1. Press the play mode button and press the menu button. 2. Press the LEFT/ RIGHT button and select the [Resize] menu tab. 3. Select a desired sub menu by pressing the UP/ DOWN button and press the OK button.
Effect ■ By using the camera’s digital processor, it is possible to add special effects to your images. 1. Press the play mode button and press the menu button. 2. Press the LEFT/ RIGHT button and select the [Effect] menu tab. 3. Select a desired sub menu by pressing the UP/ DOWN button. [B & W] : Captured images will be stored in black and white [Sepia] : Captured images will be stored in a sepia tone (a gradient of yellowish brown colours). [Red] : Captured images will be stored in a red tone.
Rotating an image ■ You can rotate the stored images by various degrees. Once the playback of the rotated picture is finished, it will switch back to the original state. 1. Press the play mode button and press the menu button. 2. Press the LEFT/ RIGHT button and select the [Rotate] menu tab. 3. Select a desired sub menu by pressing the UP/ DOWN button.
DPOF : Standard ■ This function allows you to embed print quantity information on a stored image. 1. Press the play mode button and press the menu button. 2. Press the LEFT/ RIGHT button and select the [DPOF] menu tab. 3. Select the [Standard] menu by pressing the UP/ DOWN button and press the RIGHT button. 4. Select a desired sub menu by pressing the UP/ DOWN button and press the OK button. [Select] : Selection window for an image to print is displayed. - Up/Down/Left/Right : Select an image to print.
DPOF : Print size ■ You can specify the print size when printing images stored on the memory card. The [Size] menu is available only for DPOF 1.1 compatible printers. ● Setting the Print Size 1. Press the play mode button and press the menu button. 2. Press the LEFT/ RIGHT button and select the [DPOF] menu tab. 3. Select the [Size] menu by pressing the UP/ DOWN button and press the RIGHT button. 4. Select a desired sub menu by pressing the UP/ DOWN button and press the OK button.
Copy To Card ■ This enables you to copy image files, movie clips and voice recording files to the memory card. ● Copying to the Memory Card 1. Press the play mode button and press the menu button. 2. Select the [Copy to Card] menu tab by pressing the Copy To Card LEFT/ RIGHT button. No Yes 3. Select a desired sub menu by pressing the UP/ DOWN button and press the OK button. - [No] : Cancels "Copy to Card".
On Screen Display information ■ You can check shooting information about the displayed image. ● How to select the type of information you want to see 1. Press the play mode button and press the menu button. 2. Select the [OSD Information] menu tab by pressing the LEFT/ RIGHT button. 3. Select a desired sub menu by pressing the UP/ DOWN button and press the OK button.
PictBridge ■ You can use the USB cable to connect this camera to a printer that supports PictBridge (sold separately) and print the stored images directly. Movie clips and voice files cannot be printed. ● Setting up the camera for connection with the printer 1. In any mode with the exception of Voice Recording mode, press the MENU button. 2. Press the LEFT/ RIGHT button and select [Setup] menu tab. 3. Select [USB] menu by pressing the UP/ DOWN button and press the RIGHT button. 4.
PictBridge : Picture Selection ■ Easy printing When you connect the camera to printer in the Play back mode, you can print a picture easily. - Pressing the shutter button : Currently displayed image will be printed with the printer’s default setting. - Pressing the Left/ Right button : Selects a previous/ next image. 141-0001 ◀ ▶ Print:Shutter Menu:OK ■ Select pictures to print 1. The [Images] menu will appear. 2.
PictBridge : Print Setting ■ AUTO SET 1. Use the LEFT and RIGHT buttons to select the [Auto Set] menu tab. 2. Use the UP and DOWN buttons to select the desired submenu value, and then press the OK button. [No] : [Custom Set] values are kept. [Yes] : All values in the [Custom Set] are automatically changed. Auto Set No Yes Exit : MENU Move: ■ Custom Set : You can select the Paper Size, Print Format, Paper Type, Print Quality, Date Print, and File Name Print menus for printed pictures. 1.
PictBridge : Printing ■ Printing Pictures 1. Use the LEFT and RIGHT buttons to select the [Print] menu tab. 2. Use the UP and DOWN buttons to select the desired submenu value, and then press the OK button. [Standard] : Print the pictures stored in the memory card in set numbers. One picture is printed on one piece of paper. [Index] : Print multiple images on one sheet of paper. 3. The screen shown on the right will appear and the picture will be printed.
PictBridge : RESET ■ Initialises user-changed configurations. 1. Use the LEFT and RIGHT buttons to select the [Reset] menu tab. 2. Use the UP and DOWN buttons to select the desired submenu value, and then press the OK button. If [No] is selected : Settings will not be reset. If [Yes] is selected : All print and image settings will be reset. Reset No Yes Exit : MENU Move: ※ Default print setting varies depending on the printer manufacturer.
Setup menu ■ In this mode, you can set up basic settings. You can use the setup menu in all camera modes, except Voice Recording and MP3 modes. The items indicated by are default settings. Menu tab Main menu File Power Save Sub menu Secondary menu Series - Reset - 1, 3, 5, 10 min - Page p.95 p.96 ENGLISH 한국어 FRANÇAIS DEUTSCH ESPAÑOL ITALIANO 日本語 Language P”CCK»… PORTUGUÊS DUTCH DANSK SVENSKA SUOMI p.
Setup menu Menu tab Main menu AF Lamp LCD Video Out Quick View Reset Sub menu Secondary menu Off - On - Dark - Normal - Bright - NTSC - PAL - Off, 0.5, 1, 3 sec - No - Yes - Page p.100 p.100 p.101 p.103 p.103 ※ Menus are subject to change without prior notice. File name ■ This function allows the user to select the file naming format. ● Assigning File Names 1. In any mode with the exception of Voice Recording and MP3 mode, press the MENU button. Setup 2.
File name INFORMATION ● The first stored folder name is 100SSCAM, and the first file name is SSM10001. ● File names are assigned sequentially from SSM10001 → SSM10002 → ~ → SSM19999. ● The folder number is assigned sequentially from 100 to 999 as follows: 100SSCAM → 101SSCAM → ~ → 999SSCAM. ● The files used with the memory card conform to the DCF(Design rule for Camera File systems) format.
Language ■ There is a choice of languages that can be displayed on the LCD monitor. Even if the battery and AC charger are removed and inserted again, the language setting will be preserved. ● Setting Language 1. In any mode with the exception of Voice Recording and MP3 mode, press the MENU button. Setup File ENGLISH 2. Press the LEFT/ RIGHT button and select the [Setup] menu tab. Power Save 한국어 3.
Setting up the Date/ Time/ Date type ■ You can change the date and time that will be displayed on the captured images and set up the date type. ● Setting Date/Time & Selecting Date Format 1. In any mode with the exception of Voice Recording and MP3 mode, press the MENU button. Setup File 2. Press the LEFT/ RIGHT button and select the [Setup] ▲ Power Save menu tab. 05/ 05/ 01 13:01 Language ▼ Format 3. Select the [Date&Time] menu by pressing the UP/ DOWN yy/mm/dd Date&Time button and press the RIGHT button.
Sound ■ If you set the operation sound to ON, various sounds will be activated for camera startup, when button are pressed, and if there is a card error, so that you can be aware of the camera operation status. ● Setting Operation Sounds 1. In any mode with the exception of Voice Recording and MP3 mode, press the MENU button. 2. Press the LEFT/ RIGHT button and select the [Setup] menu tab. 3. Select the [Sound] menu by pressing the UP/ DOWN button and press the RIGHT button. 4.
Auto Focus lamp ■ You can turn on and off the Auto Focus lamp ● How to set up the lamp 1. In any mode with the exception of Voice Recording and MP3 mode, press the MENU button. 2. Press the LEFT/ RIGHT button and select the [Setup] menu tab. 3. Select the [AF Lamp] menu by pressing the UP/ DOWN button and press the RIGHT button. 4. Select a desired sub menu by pressing the UP/ DOWN button and press the OK button. If [Off] is selected : The AF lamp will not light up.
Selecting Video out type ■ The Movie output signal from the camera can be NTSC or PAL. Your choice of output will be governed by the type of device (monitor or TV, etc.) to which the camera is connected. PAL mode can support only BDGHI. ● Setting the Video Out Type 1. In any mode with the exception of Voice Recording and MP3 mode, press the MENU button. 2. Press the LEFT/ RIGHT button and select the [Setup] menu tab. 3. Select the [Video Out] menu by pressing the UP/ DOWN button and press the RIGHT button.
Selecting Video out type INFORMATION ● NTSC : U.S.A, Canada, Japan, South Korea, Taiwan, Mexico. ● PAL : Australia, Austria, Belgium, China, Denmark, Finland, Germany, U.K., Holland, Italy, Kuwait, Malaysia, New Zealand, Singapore, Spain, Sweden, Switzerland, Thailand, Norway. ● When using a TV as an external monitor, you will need to select the external or AV channel of the TV. ● There will be a digital noise on the external monitor, but it is not a malfunction.
Quick view ■ If you enable Quick View before capturing an image, you can view the image you just captured on the LCD monitor for the duration set in the [Quick View] setup. Quick view is possible only with still images. ● Setting Quick View 1. In any mode with the exception of Voice Recording and MP3 mode, press the MENU button. Setup 2. Press the LEFT/ RIGHT button and select the [Setup] USB Off AF Lamp 0.5 sec menu tab. LCD 1 sec Video Out 3 sec 3.
Setting up the Mycam menu ■ You can set up a start up image, start up sound and shutter sound. Every camera working mode (with the exception of Voice recording and MP3 mode) has the MyCAM menu. The items indicated by are default settings. Menu tab Main menu S.Image S.Sound SH.Sound Sub menu Page Off LOGO User Image 1 User Image 2 Off Sound 1 Sound 2 Sound 3 Off Sound 1 Sound 2 Sound 3 p.104 p.105 p.105 ※ Menus are subject to change without prior notice.
Start up sound ■ You can select the sound that is activated whenever the camera is turned on. ● Setting the Startup Sound 1. In any mode with the exception of Voice Recording and MP3 mode, press the MENU button. 2. Press the LEFT/ RIGHT button and select the [Mycam] menu tab. 3. Select the [S.Sound] menu by pressing the UP/ DOWN button and press the RIGHT button. 4. Select a desired sub menu by pressing the UP/ DOWN button and press the OK button. 5. Press the menu button twice and the menu will disappear.
MP3 mode ■ Digimax i50 MP3 player This camera has an embedded MP3 player program. You can save the MP3 files on this camera and listen to the MP3 files that is near enough to compact disk quality. Downloading MP3 files ■ To use MP3 files, they must be saved in the internal memory or memory card of this camera. 1. Save the desired files on your PC. 2. Connect the camera to your PC with the USB cable and turn on the camera. 3. Open Window's EXPLORER and search for [Removable Disk]. 4.
Starting the MP3 mode ■ You can select the MP3 mode by using the M (Mode) button located on the back of the camera and through the [Mode] menu. ● Selecting the [Mode] menu 1. Insert the battery (p.17). 2. Insert the memory card that holds MP3 files (p.20). As this camera has a 48MB internal memory, you can save Mode Still/ Movie/ MP3 MP3 files on the internal memory too. Full 3. Close the battery chamber cover. 4. Press the power button to turn on the camera. 5.
Starting the MP3 mode ● Changing the MP3 mode : If the [Full] menu was selected, steps from 1-4 are the same as those for selecting the [Mode] menu. 5. The recording mode used just before will display. 6. Press the M (Mode) button located on the back of the camera and the mode selection menu will display. 7. To select the MP3 mode, press the Left/Right button. MP3 8. Press the Play button ( ) and an MP3 file will play Set:OK/M back. To use your earphones, insert them into the Earphones jack. 9.
LCD monitor indicator for MP3 mode ■ The LCD monitor displays information about the MP3 file. ① ⑨ ② ⑧ ③ Sample1.mp3 ④ 00:33/ 04:07 ⑤ ⑦ ⑥ No. Description Icons Page 1 Type of playing back p.113 2 MP3 mode - 3 Battery status 4 Title of MP3 5 Time line 6 Playing time 7 Control button p.112 8 Volume p.112 9 Sampling rate, Bit rate - p.17 Sample1.mp3 p.
Using the camera buttons to adjust the camera Playlist button ■ You can see the MP3 files list and select a file. ● Selecting MP3 files 1. In the MP3 mode, press the ( ) button. The cursor will highlight a file that had been played back at the time the list button was pressed. 2. You can select a file by pressing the Up/ Down button. Pressing the Left/ Right button scrolls the previous/next page of the lists. Playlist Ballade Dance Techwin.mp3 Track05.mp3 Track01.mp3 Track02.mp3 Track03.
Using the camera buttons to adjust the camera Hold button ● If you press the Hold button for over 1 second, the camera buttons are locked. ● When the camera buttons are locked, an icon as shown will display. Track01.mp3 00:33/ 04:07 ● If the camera buttons are locked, the buttons can't be operated while playing back. Only the Power off, Video out, USB connection and LCD on function can be operated. ● If you press the Lock button again or turn off the camera, the camera is released.
Using the camera buttons to adjust the camera Volume button ■ You can control the volume with this button. ■ There are 0~30 steps. If you press it for a short time, the volume the volume will increase or decrease with 1 step and if you press and hold it, the volume will increase/decrease continuously. Control button ■ When a file is playing back, press the Down button to pause the file. Pressing it again will resume playback. ■ You can search the MP3 files by pressing the Left/ Right button.
Setting up the play back function using the LCD monitor ■ MP3 mode functions can be changed by using the LCD monitor. In the MP3 mode, pressing the MENU button displays the menu on the LCD monitor. The menus you can set up in MP3 mode are as follows. Menu tab Main menu Sub menu Page Play One Repeat One Play mode Play All p.113 Repeat All Shuffle Delete all Slide show No All Off On p.114 p.114 ※ Menus are subject to change without prior notice.
Setting up the play back function using the LCD monitor Delete all ■ How to delete the files 1. In the MP3 mode, press the Menu button. Delete All 2. Select the [Delete All] menu tab by pressing the Left/Right button. No All Exit:MENU 3. Select a desired menu by pressing the Up/ Down button and press the OK button. [No] : Cancel the "Delete files" [All] : a confirmation window will display. Select the [Delete] menu and press the OK button.
Important notes Be sure to observe the following precautions! ■ This unit contains precision electronic components. Do not use or store this unit in the following locations. - Areas exposed to severe changes in temperature and humidity. - Areas exposed to dust and dirt. - Areas exposed to direct sunlight or the inside of a vehicle in hot weather. - Environments where there is high magnetism or excessive vibration. - Areas with high explosives or highly flammable materials.
Important notes ■ Caution on Using the Lens - If the lens is subjected to direct sunlight, it could result in discoloration and deterioration of the image sensor. - Pay attention not to get fingerprints or foreign substances on the surface of the lens. ■ If the digital camera is not used for a long period, an electric discharge can occur. It is a good idea to remove the batteries and the memory card if you do not intend using the camera for an extended period of time.
Warning indicator ■ There are several warnings that may appear on the LCD display Card Error! ㆍMemory card error → Turn off the camera power and turn it on again → Insert the memory card again → Insert the memory card and format the memory card (p.97) Memory Error! ㆍInternal memory error → Turn off the camera power and turn it on again → Format the memory with the memory card removed. (p.
Warning indicator Low Light! ㆍWhen taking pictures in dark places → Take pictures in Flash Photography mode. Out Of Number ㆍWhen selecting too many printing pages in the PictBridge menu. → Select printing page within the limitation. Capturing! ㆍWhen you take an image in the SF mode, Night scene and Fireworks scene modes. → Do not move while the message is displaying to get a fine image.
Before contacting a service centre Camera does not take images when pressing the Shutter button ㆍThere is insufficient memory capacity → Delete unnecessary image files ㆍThe memory card has not been formatted → Format the memory card (p.97) ㆍThe memory card is exhausted → Insert a new memory card ㆍThe memory card is locked → Refer to [Card Locked!] error message (p.117) ㆍThe camera’s power is off → Turn the camera power on ㆍThe battery are exhausted → Insert charged battery (p.14 ~ 17).
Before contacting a service centre The camera buttons do not operate ㆍCamera malfunction → Remove /re-insert battery and switch the camera on A card error has occurred while the memory card is in the camera.
Specifications 1/2.5" CCD Approx. 5.0 Mega-pixel Approx. 5.1 Mega-pixel SHD Lens f = 6.6 ~ 19.8mm (35mm film equivalent : 39 ~ 117mm) F 3.5 ~ F 4.5 Lens Still Image mode : 1.0X ~ 5.0X Digital Zoom Play mode : 1.0X ~ 10.1X (depends on image size) LCD Monitor 2.
Specifications Media File Format Image Size Storage Capacity (32MB) Image Play Type Editing Interface Power Source Dimensions (WxHxD) Weight Operating Temperature Operating Humidity Software Camera Driver Application Special Features 《122》 Internal memory : Approx. 48MB flash memory External memory : SD card /MMC (Up to 1GB Guaranteed) * Internal memory is subject to change without prior notice. Still Image : JPEG (DCF), EXIF 2.2, DPOF 1.1, PictBridge 1.
Specifications ※ MP3 player Audio File Play Mode Frequency Earphone Port Output Noise Ratio File Format Bit Rate 20Hz~20KHz 3.5mm Port (Stereo Type) Maximum Volume Left 15mW + Right 15mW(16Ω) 85 dB with 20 KHz LPF MP3 (MPEG-1/2/2.5 Layer 3) 48 ~ 320kbps (Including VBR) One, All, Repeat One, Repeat All, Random, Slide Show On/Off (User Selectable) ※ Specifications are subject to change without prior notice. ※ All trademarks are the property of their respective owners.
Software Notes Please ensure that you read the instruction manual carefully before use. ㆍThe attached software is a camera driver and image editing software tool for Windows. ㆍUnder no circumstances should all or part of either the software or the user manual be reproduced. ㆍCopyrights for software are licensed only for use with a camera. ㆍIn the unlikely event of a manufacturing fault, we will repair or exchange your camera.
About the software After inserting the CD-ROM provided with this camera into the CD-ROM drive, the following window should automatically run. Before connecting the camera to the PC, you should first install the camera driver. ■ Camera driver : This enables images to transfer between the camera and PC. This camera uses the USB Storage Driver as the camera driver. You can use the camera as a USB card reader.
About the software ■ Digimax Reader : Text recognition program. (p.150) You can save an image file that was captured in the TEXT mode as a text file with this program. This software is only compatible with Windows. INFORMATION ● Be sure to check the system requirements before installing the driver. ● You should allow 5 ~ 10 seconds for running the automatic setup program according to the capability of your computer. If the frame does not show, run the [Windows Explorer] and select [Samsung.
Setting up the application software To use this camera with a PC, install the application software first. After this has been done, the stored images in the camera can be moved to the PC and can be edited by an image editing program. INFORMATION ● Close other programs before installing the application software. ● Before installing the application software, disconnect the USB connection. You can visit the Samsung web-site through the internet. http://www.samsungcamera.com : English http://www.
Setting up the application software 4. A window will open. Click the [Next(N) >] button. [Click !] 5. DirectX Installation is completed. Click the [Finish] button and then the Xvid codec installation will be started. * The system will not reboot even if you click the [Finish] button. * The screen shot of step 5 can be different from the illustration depending on the system [Click !] requirements. 6. A windows to check whether the PC has XviD codec or not will display.
Setting up the application software 7. If an error listed below takes place during the preview, click the [Install] button to install the XviD codec. - Only a voice plays back. - An error message displays and the movie clip does not play back. * A window shown alongside may display according to the system requirements. [Click !] 8. The XviD codec installation window will be displayed as shown alongside. Click the [Next >] button. [Click !] 9. The Software License Agreement window will be displayed.
Setting up the application software 10. The XviD information window will display. Click the [Next >] button. [Click !] 11. The destination selection window will open. Click [Next >] button. To copy to the files to another folder, click [Browse...] and choose a folder you want. [Click !] 12. A window will open, asking you to choose a folder to which program icons will be added. Click [Next >] button.
Setting up the application software 14. The XviD codec is ready to install. Click the [Install] button. [Click !] 15. Installation is complete. Click the [Finish] button. [Click !] 16. A window where you can choose the program you want to install will appear. Click [Install]. For information on application software, please refer to page 125, 126. [Click !] INFORMATION ● If you select [Exit] at step 16, the application program installation will be cancelled. 17.
Setting up the application software INFORMATION ● If you select [Cancel] at step 17, a window for installing Digimax Reader will be displayed. 18. A window will open. Click the [Next >] button. [Click !] 19. A destination selection window will open. Click [Next >]. To copy the files to another folder, click [Browse..] and choose a folder you want. [Click !] 20. A window will open, asking you to choose a folder to which program icons will be added. Click [Next >] button.
Setting up the application software 22. Digimax Master installation is successfully completed. Click the [Finish] button to install Digimax Reader. * The screen shot of step 22 can be different from the illustration depending on the system requirements. [Click !] 23. A window will be displayed as shown alongside. Click the [INSTALL] button. - If you click the [Manual] button, instructions for using Digimax reader will be displayed.
Setting up the application software 26. A destination selection window will open. Click the [Next >] button. To copy the files to another folder, click [Browse...] and choose a folder you want. [Click !] 27. Digimax Reader Installation is completed. The system will not reboot even if the [Yes, I want to restart the computer now] option is selected. ※ The screen shot of step 27 can be different from the illustration depending on the system requirements. [Click !] 28.
Setting up the application software 31. If you can see [Removable Disk] under [My computer], the camera driver installation was successful. Now you can transfer image files from the camera to PC via the USB cable. INFORMATION ● If you have installed the camera driver, The [Found New Hardware Wizard] may not open. ● On a Windows 98 or 98 SE system, the Found New Hardware Wizard dialog box opens and a window asking you to select a driver file may appear. In this case, specify "USB Driver" in the CD supplied.
Starting PC mode • If you connect the USB cable to a USB port on your PC and then turn on the power, the camera will automatically switch to "computer connection mode". • In this mode, you can download stored images to your PC through the USB cable. ■ Connecting the camera to a PC 1. In any mode with the exception of Voice Recording and MP3 mode, press the MENU button. 2. Press the LEFT/ RIGHT button and select the [Setup] menu tab. 3.
Starting PC mode ■ Downloading stored images You can download the still images stored on the camera to your PC's hard disk and print them or use a photo editing software to edit them. 1. Connect the camera to your PC with the USB cable. 2. On your computer's desktop display, select [My computer] and double click [Removable Disk → DCIM → 100SSCAM]. The image files will then be displayed. 3. Select an image and press the right mouse button. 4. A pop-up menu will open. Click the [Cut] or [Copy] menu.
Starting PC mode 6. Press the right mouse button and a pop-up menu will open. Click [Paste]. 7. An image file is transferred from the camera to your PC. - By using [Digimax Master], you can see the stored images in the memory directly on the PC monitor and you can copy or move the image files.
Removing the USB Driver for Windows 98SE ■ To remove the USB driver, refer to the process shown below. 1. Click [Start → Settings] and click [Control Panel]. 2. Double-click [System]. 3. Select [Device manager → Hard Disk Controller → Samsung Digital Camera] and click the [Delete] button. [Click !] 4. Click the [OK] button. The camera is removed from the system.
Removing the USB Driver for Windows 98SE 5. Click [Start → Settings → Control Panel] and double click [Add/Remove programs]. 6. The [Add/Remove Programs Properties] window will open. Click [Digimax i50 MP3] and click the [Add/Remove] button. [Click !] 7. Uninstallation is complete. Click the [Finish] button and the window will disappear.
Removable Disk ■ To use this camera as a Removable Disk, install (p.127) the USB Driver. 1. Before turning the camera power on, connect the camera to the PC with the USB cable. 2. Click [Removable Disk] under [My computer] or [Windows Explorer]. 3. Image files stored in the Removable Disk (DCIM → 100SSCAM) can be transferred to the PC. INFORMATION Important information whilst using the Removable Disk ● The [Removable Disk] indicator will not show when the camera power is off or the USB cable is removed.
Removing the removable disk ■ Windows 98SE 1. Check whether the camera and PC are transferring a file. If the camera status lamp blinks, you have to wait until the lamp illuminates. 2. Unplug the USB cable. ■ Windows 2000/ME/XP (The illustrations may be different from the real display in accordance with the Windows O/S.) 1. Check whether the camera and PC are transferring a file. If the camera status lamp blinks, you have to wait until the lamp illuminates. 2.
Removing the removable disk 6. A [Unplug or Eject Hardware] window will open. Click the [Close] button and the removable disk will be removed safely. 7. Unplug the USB cable. [Click !] Setting up the USB Driver for MAC 1. A USB Driver for MAC is not included with the software CD as MAC OS supports the camera driver. 2. Check the MAC OS. You can check the MAC OS version during MAC OS start-up. This camera is compatible with MAC OS 9.2 ~ 10.3. 3.
Digimax Master ■ You can download, view, edit and save your images and movies with this software. This software is only compatible with Windows except for the Windows 98. ■ To start the program, click [Start → Programs → Samsung → Digimax Master]. ● Downloading images 1. Connect the camera to your PC. 2. A window for downloading images will display after connecting the camera and your PC. - To download the captured images, select the [Select All(A)] button.
Digimax Master 4. Select a destination and make a folder to save downloaded images and folders. - Folder names can be made in order of date and images will be downloaded. - Folder name will be made as you want and images will be downloaded. - After selecting a folder that was made before, images will be downloaded. 5. Click [Next(N) >] button. [Click !] 6. A window will open as shown alongside. The destination of the selected folder will be displayed on the upper side of the window.
Digimax Master ● Image viewer : You can view the stored images. ① ⑤ ⑥ ⑦ ② ③ ④ - Image viewer functions are listed below. ① Menu bar : You can select menus. File, Edit, View, Tools, Change functions, Auto download, help, etc. ② Image selection window : You can select the desired images in this window. ③ Media type selection menu : You can select image viewer, image edit and movie edit functions in this menu.
Digimax Master ● Image edit : You can edit the still image. ① ④ ② ③ - Image edit functions are listed below. ① Edit menu : You can select the following menus. [Tools] : You can resize or crop the selected image. See the [Help] menu. [Adjust] : You can modify image quality. See the [Help] menu. [Retouch] : You can change image or insert effects on the image. See the [Help] menu. ② Drawing tools : Tools for editing an image. ③ Image display window : a selected image displays in this window.
Digimax Master ● Movie edit : You can get the still image, movie clip, narration, music files together in a movie clip. ① ② - Movie clip edit functions are listed below. ① Edit menu : You can select the following menus. [Add Media] : You can add other media elements to a movie. [Edit Clip] : You can change the brightness, contrast, colour and saturation. [Effects] : You can insert an effect. [Set Text] : You can insert texts. [Narrate] : You can insert a narration.
Digimax Master ㆍMovies for viewing on the camera : You can play back a movie on this camera 1. Select a movie for playing back on the camera by pressing the [Add] button. Insert effects and edit the movie. To save the edited movie, press the [Make] button. 2. Select [Movie for camera] video type. 3. Select Camera option, Output location, File name and press the [Make] button. - Frame size : Selecting the width and height of the frame. - Frame rate : Selecting the frame rate per second.
Digimax Reader ■ Digimax Reader is a Text recognition program. You can save an image file that is captured in the Text mode, as a text file with this program. This software is only compatible with Windows. ■ To start the program, click [Start → Programs → Digimax Reader Eng]. The following screen will appear. ■ How to use the Digimax Reader 1. Connect the camera and the PC with a USB cable and download the images that were stored in the camera to the PC.
Digimax Reader 5. Click the Area Analysis( ) icon to scan the image. 6. Part of the image you selected will be displayed as shown. 7. Click the Character Recognition( ) icon. The part selected in the previous step will be recognized as text. 8. To save the section as a text, click the Save( ) icon. A window as shown alongside will be displayed. 9. Select the file type that you want. Selectable file types : *.TXT, *.HWP, *.DOC, *.
FAQ ■ Please check the following if the USB connection malfunctions. [Case 1] The camera power is off. → Turn the camera power on. [Case 2] USB Driver is not installed correctly. → Install the USB Driver correctly. Refer to page 127. [Case 3] The USB cable is not connected or you are using a cable with an incorrect specification. → Use a USB cable with the correct specification. [Case 4] The camera is not recognized by your PC.
FAQ There must be USB Host Controller and USB root hub under [Universal Serial Bus controllers]. In addition, double-click on the USB Universal Host Controller and the USB Root Hub to check if the Device Status states "This device is working properly". If the Device Status says the device is "not working properly", click the "Driver" tab and then click [Update Driver] or [Reinstall Driver]. → When all the conditions mentioned above are met, the computer can support the USB interface.
FAQ ■ When the movie clip doesn’t play back on the PC ※ When the movie clip recorded by the camera doesn’t play back on the PC, the causes are mostly due to the codec installed on the PC. ● When codec for play back the movie clip isn’t installed → Install the codec as listed below. [Installing codec for Windows] 1) Insert the CD provided with the camera 2) Run the windows explorer and select [CD-ROM drive:\XviD] folder and click the XviD codex-1[1].1.0.exe file.
FAQ ● If a PC (Windows 98) stops responding while the camera and PC are connected repeatedly → If a PC (Windows 98) is turned on for a long time and the camera is connected repeatedly, the PC may not recognise the camera. In this case, re-start the PC. ● If a PC connected with the camera stops responding while Windows is starting. → In this case, disconnect the PC and the camera and Windows will start. If the problem happens continuously, set the Legacy USB Support to disable and re-start the PC.
SAMSUNG TECHWIN CO., LTD. OPTICS & DIGITAL IMAGING DIVISION 145-3, SANGDAEWON 1-DONG, JUNGWONGU, SUNGNAM-CITY, KYUNGKI-DO, KOREA 462-121 TEL : (82) 31-740-8086,8088, 8090, 8092, 8099 FAX : (82) 31-740-8398, 8111 www.samsungcamera.com SAMSUNG OPTO-ELECTRONICS AMERICA, INC. HEADQUARTERS 40 SEAVIEW DRIVE, SECAUCUS, NJ07094, U.S.A. TEL : (1) 201-902-0347 FAX : (1) 201-902-9342 WESTERN REGIONAL OFFICE 18600 BROADWICK ST., RANCHO DOMINGUEZ, CA 90220, U.S.A. TEL : (1) 310-900-5263/5264 FAX : (1) 310-537-1566 www.
