User’s Manual Thank you for buying a Samsung Camera. This manual will guide you through using the camera, including capturing images, downloading images and using the application software. Please read this manual carefully before using your new camera.
Instructions ■ Use this camera in the following order Set up the camera driver Before connecting the camera to a PC, via the USB cable, you will need to set up the camera driver. Install the camera driver that is contained in Application software CD-ROM. (p.117) Take a picture. (p.24) Take a picture Insert the USB cable Check the camera’s power Check [Removable Disk] Insert the supplied USB cable into the PC’s USB port and the camera’s USB connection terminal. (p.127) Check the camera’s power.
Contents READY ●Getting to know your camera ●Danger ●Warning ●Caution ●An FCC warning ●System chart ●Identification of features ■Front & Top ■Back & Bottom ■Bottom/ 5-function button ■Cradle ■Self-timer lamp ■Camera Status Lamp ■Mode icon ●Connecting to a Power Source ■Using the SAC-41 ■Using the battery ■Removing the battery ●Instructions on how to use the memory card ●Inserting the memory card ●Removing the memory card ●When Using the Camera for the First Time 5 6 6 7 7 8 10 10 10 11 11 12 12 12 13 14 18
Contents ■Playing back a movie clip 63 ■How to capture the movie clip 63 ■On camera movie trimming 64 65 ■Playing back a recorded voice ●LCD monitor indicator 66 ●Using the camera buttons to adjust the camera 67 ■Play mode button 67 68 ●Thumbnail/ Enlargement button ●Voice memo/ Up button 69 ●Play & Pause/ Down button 70 ●Delete button 71 ●Left / Right / Menu / OK button 72 73 ●Album button ●Setting up the play back function using the LCD monitor 76 ●Starting the slide show 79 ●Protecting images 81 82 ●Dele
Getting to know your camera Thank you for buying a Samsung Digital Camera. ● Prior to using this camera, please read the user manual thoroughly. ● When you require After Sales service, please bring the camera and the cause of the camera malfunction (such as battery, Memory card etc.) to the A/S centre. ● Please check that the camera is operating properly prior to when you intend to use it (e.g. for a trip or an important event) to avoid disappointment.
Danger ■ Do not attempt to modify this camera in any way. This may result in fire, injury, electric shock or severe damage to you or your camera. Internal inspection, maintenance and repairs should be carried out by your dealer or Samsung Camera Service centre. ■ Please do not use this product in close proximity to flammable or explosive gases, as this could increase the risk of explosion. ■ Should any form of liquid or a foreign object enter the camera, do not use it.
Caution ■ Leaking, overheating, or burst battery could result in fire or injury. •Use battery with the correct specification for the camera. •Do not short circuit, heat or dispose of battery in fire. •Do not insert the battery with the reverse polarities. ■ Remove the battery when not planning to use the camera for a long period of time. Battery may leak corrosive electrolyte and permanently damage the camera’s components. ■ Do not fire the flash while it is in contact with hands or objects.
System chart Please check that you have the correct contents before using this product. The contents can vary depending on the sales region. To buy the optional equipment, contact your nearest Samsung dealer or Samsung service centre. < Included items > Pouch DPOF compatible printer (see p.85) AC cord AC cord User manual, Product warranty Camera strap Software CD (see p.115, 116) SD memory card/MMC (see p.
System chart System Requirements For Windows Computer PictBridge compatible printer(see p.89) •PC with processor better than MMX Pentium 233MHz (XP : Pentium II 300MHz) •Windows 98/98SE/2000/ME/XP •Minimum 32MB RAM (XP : 128MB) •140MB of available hard-disk space •USB port •CD-ROM drive •800x600 pixels, 16-bit colour display compatible monitor (24-bit colour display recommended) For Macintosh USB cable •Power Mac G3 or later •Mac OS 9.2 ~ 10.
Identification of features Front & Top SF mode button Shutter button Microphone Power button Flash Speaker Self-timer lamp/ Auto Focus lamp Optical 3X zoom lens/ Lens cover ※ Take care not to press the lens, lens cover and camera by force. This may cause the camera malfunction.
Identification of features Bottom / 5-function button Memory card slot Voice memo/ Voice recording/ UP button MENU/ OK button FLASH/ LEFT button SELF-TIMER/ RIGHT button Battery chamber Battery holder Battery chamber cover Macro / DOWN button Play & Pause button Cradle ■ You can recharge your rechargeable battery, transfer a captured image to print, and download images with the cradle.
Identification of features ■ Self-timer lamp Icon Status Description Blinking For the 2 seconds, the lamp blinks quickly at 0.25-second intervals. Blinking For the final 2 seconds, the lamp blinks quickly at 0.25-second For the first 8 seconds, the lamp blinks at 1 second intervals. intervals. A picture will be taken after about 10 seconds and 2 seconds later a Blinking second picture will be taken.
Connecting to a Power Source ■ You should use the rechargeable battery (SLB-0737) supplied with the camera. Be sure to charge the battery before using the camera. ■ SLB-0737 rechargeable battery Specification Model SLB-0737 Type Lithium Ion Capacity 760mAh Voltage 3.7V Charging time Approx. 150 MIN (Using the SAC-41) ■ Number of images and battery life Still image Movie Battery life Number of images Recording time Approx. 90 MIN Approx. 180 Approx.
Connecting to a Power Source Using the SAC-41 If you have access to a mains supply, using an SAC-41 allows the camera to be used for long periods of time. Plug the SAC-41 into the DC connection terminal on the camera or cradle. Before turning on the camera power with an SAC-41, insert the rechargeable battery that was charged for over 10 minutes with turning off the camera. DANGER ● Always turn off the power before taking the SAC-41 out of the mains supply.
Connecting to a Power Source ■ How to charge the rechargeable battery (SLB-0737) with the SAC-41. ● Charging with the camera 1. Insert the rechargeable battery into the battery chamber. 2. Put the SAC-41 into your power socket and DC connection terminal of the camera.
Connecting to a Power Source ■ Charging LED of the SAC-41 Status Using the cradle Direct to the camera Being Charged Red LED is on Red LED is on Charging is complete Green LED is on Green LED is on Charging error Red LED is off or blinking Red LED is off or blinking ● If there is a charging error, please check all the power connections are in place. ● A USB cable for transmitting data can’t be used for charging the rechargeable battery.
Connecting to a Power Source ■ How to charge the rechargeable battery (SLB-0737) with the SBC-L5. 1. Insert the AC cord into the charger. 2. Plug the AC cord's power plug into the wall outlet. 3. Place the (-) and (+) terminals of the battery in the correct position. The red charge indicator indicates normal charging. 4. When charging is complete, the indicator turns green.
Connecting to a Power Source Using the battery : If the camera does not turn on after you have inserted battery, please check whether the battery are inserted with the correct polarity(+/-). 1. Open the battery chamber cover by pushing in the direction of the arrow. 2. Insert the battery taking note of the polarity (+ / -). 3. To close the battery chamber cover, push it until it clicks. Removing the battery 1. Turn off the camera power. Open the battery chamber cover and move the battery holder aside.
Instructions on how to use the memory card ● Be sure to format the memory card (see p.97) if you are using a newly purchased memory for the first time, if it contains data that the camera cannot recognise, or if it contains images captured with a different camera. ● Turn off the camera power whenever the memory card is being inserted or removed. ● Repeated use of the memory card will eventually reduce the memory card’s performance. Should this be the case, you will need to purchase a new memory card.
Instructions on how to use the memory card INFORMATION ● Don't remove the memory card when the camera status lamp is blinking as this may cause damage to data in the memory card. ■ The camera can use SD Memory Cards and MMC (Multi Media Cards). Please consult the enclosed manual for using the MMC Cards. The SD memory card has a write protect switch that prevents image files from being deleted or formatted. By sliding the switch to the bottom of the SD memory card, the data will be protected.
Inserting the memory card 1. Turn off the camera’s power and pull the battery chamber cover in the direction of the arrow to open. 2. Have the front of the memory card facing toward the front of the camera (lens) and the card pins toward the back of the camera (LCD monitor), and then push the memory card into the card slot until you hear a click. 3. To close, push the battery chamber cover until you hear a click. If the memory card does not slide in smoothly, do not attempt to insert it by force.
When Using the Camera for the First Time ■ Charge the rechargeable battery fully before using the camera for the first time. ■ When the camera is turned on for the first time, a menu will be displayed to set date, time and language in the LCD monitor. This menu will not be displayed after setting up the date, time and language. Set up the date, time and language before using this camera. ● Setting up the date, time and date type 1.
LCD monitor indicator ■ The LCD monitor displays information about the shooting functions and selections. ⑳ ① ⑲ ② ⑱ ③ ⑰ ④ ⑯ ⑤ ⑮ ⑥ ⑭ ⑦ ⑬ ⑧ ⑫ ⑨ ⑩ ⑪ [Image & Full Status] No. Description 1 Recording mode Icons Page p.50 2 Battery p.18 3 Continuous shot p.53 4 Flash p.37 5 Self-timer p.39 6 Macro p.35 7 Metering p.53 8 Card inserted indicator - 9 Auto focus frame - 10 Camera shake warning p.30 11 Date/ Time 12 Exposure compensation p.
LCD monitor indicator 15 RGB 16 Sharpness p.54 17 Image quality p.52 18 Image size p.51 19 RGB Number of available shots remaining 38 Remaining time (Movie clip/ Voice recording) 00:01:30/ 01:00:00 p.43 p.20 20 Voice memo/ Mic. off p.34/27 21 Optical/ Digital Zoom bar/ Digital Zoom rate p.32 Changing the recording mode ■ You can select the desired working mode by the M (Mode) button located on the back of the camera and [Mode], [Mode set] menu.
Changing the recording mode ● Changing the recording mode : If the [Still & Movie] menu was selected Steps from 1-4 are the same as those for selecting the [Mode] menu. 5. A recording mode used just before will display. 6. Press the M (Mode) button located on the back of the camera and the recording mode will change to the movie clip mode. 7. Press the M (Mode) button again and a still image mode selected on the [Mode set] menu will be selected.
Starting the recording mode ■ How to use the Auto mode Use this for shooting basic still images. 1. Select the [Full] sub menu on the [Mode] menu (p.24). 2. Select the Auto mode by pressing the M (Mode) button (p.25). 3. Point the camera towards the subject and compose the image by using the LCD monitor. 4. Press the shutter button to capture an image.
Starting the recording mode ■ Recording the movie clip without voice You can record the movie clip without voice. Steps from 1-3 are the same as those for MOVIE CLIP mode. 4. Press the Up button and the ( ) icon will display on the LCD monitor. 5. Press the shutter button and movie clip is recorded for as long as the available recording time without voice. 6. To stop the recording, press the shutter button again.
Starting the recording mode ■ How to use the Scene modes Use the menu to easily configure optimal settings for a variety of shooting situations. 1. Select the [Full] sub menu on the [Mode] menu (p.24). 2. Select the Scene mode by pressing the M (Mode) button (p.25). 3. Point the camera towards the subject and compose the image by using the LCD monitor. 4. Press the shutter button to capture an image. [SCENE mode] ※ The scene modes are listed below.
Starting the recording mode ■ How to use the VOICE RECORDING mode A voice recording can be recorded for as long as the available recording time of the memory capacity allows. (Max: 1 hour) 1. In any mode with the exception of the Movie clip, select the VOICE RECORDING mode by pressing the Voice recording button twice. 2. Press the shutter button to record a voice. - Press the shutter button once and voice is recorded for as long as the available recording time (Max : 1 hour) allows.
Things to Watch Out for When Taking Pictures ■ Pressing the shutter button down half way Lightly press the shutter button to confirm focus and flash battery charge. Press the shutter button all way down to take the picture. [ Lightly press the shutter button ] [ Press the shutter button ] ■ The available recording time may vary depending on shooting conditions and camera settings.
Using the camera buttons to adjust the camera ■ The recording mode function can be set up by using the camera buttons. POWER button ● Used for turning the camera’s power on / off. ● If there is no operation during the specified time, the camera's power will be turned off automatically to save battery life. Refer to page 96 for more information about the auto power off function. ● Pressing the power button for over 3 seconds will deactivate the start-up sound and sound function.
ZOOM W/ T button ■ This camera has a 3X optical zoom and a 5X digital zoom function. Using both will offer a total zoom ratio of 15X. ● TELE Zoom Optical zoom TELE Digital zoom TELE : Pressing the ZOOM T button. This will zoom into the subject i.e. the subject will appear nearer. : When the maximum (3X) optical zoom is selected, pressing the ZOOM T button activates the digital zoom software. Releasing ZOOM T button stops the digital zoom at the required setting.
ZOOM W/ T button INFORMATION ● Images taken using the digital zoom may take a little longer for the camera to process. Allow time for this to take place. ● The digital zoom cannot be used in movie clip shots. ● If the Zoom buttons are being pressed during the Movie clip shots, the voice will not recorded. ● You may notice a decrease in image quality when using the digital zoom.
Voice recording( ) / Voice memo( ) / UP button ■ While the menu is showing, press the UP button to move up the submenu cursor. When the menu is not displayed on the LCD monitor, the UP button operates as the voice recording ( ) or voice memo ( ) button. You can record your voice or add your voice-over to a stored still image. Refer to page 29 for more information about the voice recording. ● Recording a voice memo 1.
Macro( ) / Down button ■ While the menu is showing, press the DOWN button to move from the main menu to a submenu, or to move down the submenu cursor. When the menu is not showing, you can use the MACRO/ DOWN button to take macro pictures. The distance ranges are shown below. Press the Macro button until the desired macro mode indicator displays on the LCD monitor.
Macro( ) / Down button (Focusing) ■ Available focusing method, by recording mode ( O: Selectable , X: Not selectable, ∞: Infinity focus range) Mode Auto macro X O X O Super macro X X O X macro O X O X Normal O X O X SCENE Mode Auto macro X X X X X O X X X X X Super macro X X X X X X X X X X X macro X X X X O X X X X X X Normal O O O ∞ X X ∞ ∞ O ∞ O Focus lock ■ To focus on the subject positioned outside of the centre, use the focus lock
Flash ( ) / Left button ■ When the menu is displayed on the LCD monitor, pressing the LEFT button makes the cursor shift to the left tab. ■ When the menu is not displayed on the LCD monitor, the LEFT button operates as the FLASH ( ) button. ● Selecting the flash mode 1. Press the M (Mode) button to select a Recording mode [Selecting the Auto flash] with the exception of Movie clip mode (p.25). 2. Press the Flash button until the desired flash mode indicator displays on the LCD monitor. 3.
Flash ( ) / Left button ● Flash mode indicator Menu tab Flash mode Description Auto flash If the subject or background is dark, the camera flash will operate automatically. Auto & Red eye reduction If a subject or background is dark, the camera flash will work automatically and will reduce the red-eye effect by using the redeye reduction function. Fill in flash The flash fires regardless of available light. The intensity of the flash will be controlled, according to the prevailing conditions.
Self-timer ( ) / Right button ■ When the menu is displayed on the LCD monitor, pressing the Right button makes the cursor shift to the right tab. The right button can also be used to move to a sub menu to select a different setting. When the menu is not displayed on the LCD monitor, the RIGHT button operates as the Self-timer. This function is used when the photographer would also like to be in the image. ● Using the self-timer 1.
MENU / OK button ■ MENU button - When you press the MENU button, a menu related to each camera mode will be displayed on the LCD monitor. Pressing it again will return the LCD to the initial display. - A menu option can be displayed when the following are selected : MOVIE CLIP and STILL IMAGE mode. There is no menu available when the VOICE RECORDING mode is selected.
M (Mode) button ● How to use the mode button : In case of [Full] sub menu and Auto mode [Auto mode] Pressing the Mode button Manual Pressing the Right button Set : OK/M [Manual mode] Auto Set : OK/M [Mode selection menu] Movie Pressing the Left button Set : OK/M [Movie clip mode] Pressing the Up button Night Portrait Pressing the Left/Right button Set : OK/M Set : OK/M [Scene mode] [Selecting a scene mode] ※ Press the Mode button and the mode selection menu will disappear.
SF button ■ Pressing the SF button selects the SF(Safety Flash) mode In poor indoor light conditions, Safety Flash will help you get a good image without the use of a flash. As children are sensitive of using flash, this is suitable function for taking children. ● Things to watch out for using the SF mode 1. The SF range is 2m(WIDE) and 1.5m(TELE). 2. The digital zoom will not operate in the SF mode. 3. If the lighting conditions are brighter than fluorescent lighting condition, the SF doesn’t activate. 4.
+/- button ■ You can use the +/- button to adjust the values for the RGB, ISO, white balance, exposure compensation and Long Time shutter speed. ■ When the SF is selected, ISO value is fixed as AUTO and Exposure value is fixed as 0.0EV. Main menu Sub menu RGB R (Red), G (Green), B (Blue) ISO AUTO, 100, 200, 400 WHITE BALANCE AUTO, DAYLIGHT, CLOUDY, FLUORESCENT H, FLUORESCENT L, TUNGSTEN, CUSTOM. Exposure compensation -2.0 ~ 0.0 ~ +2.0 (0.
+/- button ■ ISO : You can select the ISO sensitivity when taking pictures. The speed or specific light-sensitivity of a camera is rated by ISO numbers. ● Selecting an ISO Sensitivity 1. Press the +/- button, and then use the UP and DOWN buttons to select the ISO icon( ). The ISO menu bar will appear as shown. 2. Use the LEFT and RIGHT buttons to select the desired ISO sensitivity value. - AUTO : The camera's sensitivity is automatically changed by variables such as lighting value or subject brightness.
+/- button ● Using the Custom White Balance White balance settings may vary slightly depending on the shooting environment. You can select the most appropriate white balance setting for a given shooting environment by setting up the custom white balance. 1. Select the CUSTOM ( ) menu of the White Balance. 2. Place a sheet of white paper in front of the camera so that the LCD monitor shows only white, and then press the SHUTTER button. 3. Your custom white balance value is stored.
+/- button ■ Long Time shutter : This camera automatically adjusts the shutter speed and aperture values to the shooting environment. However, in NIGHT SCENE mode, you can set the shutter speed and aperture values to your preference. ● Adjusting the shutter speed and aperture values 1. Select the [Night] scene mode. (M button → [Scene] → [Night]) 2. Press +/- button and Long Time shutter menu (LT, For selecting shutter speed and aperture value) will be displayed. 3.
Using the LCD monitor to adjust the camera settings ■ You can use the menu on the LCD monitor to set up recording functions. In any mode with the exception of VOICE RECORDING mode, pressing the MENU button displays the menu on the LCD monitor. INFORMATION ● The menu will not be displayed on the LCD monitor in the following circumstances: - When another button is being operated. - While image data is being processed. - When there is no battery capacity.
Using the LCD monitor to adjust the camera settings Menu tab Main menu Sub menu Camera working mode Frame Rate 30fps 15fps p.52 Metering Multi Spot p.53 Shooting Single Continuous p.53 Soft Normal Vivid - Full OSD Basic OSD Save Mode - Normal Red B&W Green Sepia Blue Negative - Off Range 1 ~ 4 Off 2~4 Parts Pano. 2 Parts - Photo Frame Off Frame 1 ~ 9 p.60 Stabilizer Off On p.61 p.54 Sharpness OSD Information p.54 p.55 Effect Highlight Composite p.56 p.
How to use the menu 1. Turn on the camera and press the MENU button. A menu for each camera mode appears. However, there is no menu for Voice Recording mode ( ). 2. Use the LEFT and RIGHT buttons to navigate through the menus. Mode Set Auto Press the LEFT or RIGHT button. Manual Press the LEFT or RIGHT button. Mode Still & Movie Size 2592 X 1944 2272 X 1704 2048 X 1536 1600 X 1200 1024 X 768 640 X 480 Full Movie Night portrait Children 3. Use the UP and DOWN buttons to select a sub menu.
Mode Set ■ You can select the desired recording mode. [Auto] [Manual] : For shooting basic still image : You can still manually configure all Mode Set Auto functions except the aperture value and Manual shutter speed. Movie Night [Movie] : For taking a movie clip portrait [Night] : Use this for shooting still images at night Children or in other dark conditions. [Portrait] : To take a picture of a person. [Children] : To take a picture of fast moving objects, for example, children.
Size ■ You can select the image size appropriate for your application.
Quality / Frame rate ■ You can select the compression ratio appropriate for your application of the captured images. The higher the compression ratio, the lower the picture quality. Mode STILL IMAGE mode MOVIE CLIP mode Icon Sub menu S. Fine Fine Normal 30FPS 15FPS File Format jpeg jpeg jpeg avi avi Frame Rate Quality S.Fine 30 FPS Fine 15 FPS Normal [ STILL IMAGE mode ] [ MOVIE CLIP mode ] INFORMATION ● S. Fine is the highest quality and Normal is the lowest setting.
Metering ■ If you cannot obtain suitable exposure conditions, you can change the metering method to take brighter pictures. [Multi] ( ) [Spot] ( ) : Exposure will be calculated based on an average of the available light in the image Metering area. However, the calculation will be Multi Spot biased towards the centre of the image area. This is suitable for general use. : Only the rectangular area in the centre of the LCD monitor will be metered for [STILL IMAGE mode] light.
Sharpness ■ You can adjust the sharpness of the picture you want to take. You cannot check the sharpness effect on the LCD monitor before you take a picture, because this function is applied only when the captured image is stored on the memory. Sub menu Icon Sharpness Soft Normal Vivid Description The edges of the image are softened. Soft This effect is suitable for editing images on your PC. The edges of the image are sharp. Normal This is suitable for printing. The edges of the image are emphasized.
Effect ■ By using the camera’s digital processor, it is possible to add special effects to your images. Effect Effect Normal Normal B&W Sepia Red Green Blue B&W Sepia Red Green Blue [MANUAL mode] [ MOVIE CLIP mode] [Normal] [B & W] [Sepia] : No effect is added to the image. : Captured images will be stored in black and white. : Captured images will be stored in a sepia tone (a gradient of yellowish brown colours). [Red] : Captured images will be stored in a red tone.
Special Effect ■ By using the camera’s digital processor, it is possible to add special effects to your images. You can select this menu only in the MANUAL mode. ■ You can select the preset focus frame, Composite shooting and Photo frame function. If a special effect is selected, the rest special functions set before are cancelled automatically. ■ Even if the camera is turned off, the special effect setting will be preserved. To cancel the special effect, select the [Off] sub menu of each menu.
Special Effect : Preset focus frames ● Moving and changing the focus frame You can change the focus frame after selecting a Range menu. 1. Point the camera towards the subject and compose the image by using the LCD monitor. 2. Press the +/- button. 3. The colour of focus frame turns white. Press the Up/Down/Left/Right button to moves the focus frame position. 4. To select the focus frame position, press the +/- button again and you can take a picture.
Special Effect : Composite shooting ■ You can combine 2 ~ 4 different shots in a still image. 1. Select the MANUAL mode, and press the menu button. 2. Press the LEFT/ RIGHT button and select the Special Effect [Special Effect] menu tab. HighLight Off Composite 2 Parts 3. Select the [Composite] menu by pressing the UP/ DOWN Photo Frame 3 Parts button and press the Right button. 4 Parts PANO.2 Part 4. Select a desired sub menu by pressing the UP/ DOWN Back:◀ Set:OK button and press the OK button.
Special Effect : Composite shooting ● Changing a part of composite shot before taking the last shot Before taking the last composite shot, you can change a part of composite shot. 1. During the composite shots, press the +/- button. 2. A previous image will be deleted and new frame will display. If there is an image taken before, press the +/- button again and a previous image will be deleted again.
Special Effect : Photo Frame ■ You can add 9 types of frame-like borders to a still image you want to capture. ■ Date & Time information will not be printed on the stored image taken with [Photo Frame] menu. 1. Select the MANUAL mode, and press the menu button. 2. Press the LEFT/ RIGHT button and select the [Special Effect] menu tab. 3. Select the [Photo Frame] menu by pressing the UP/ DOWN button and press the Right button. 4.
Movie Clip frame stabiliser ■ This function helps stabilize images captured during movie recording. You can select this menu only in the MOVIE CLIP mode. If the memory card is not inserted, this function will not operate. ● How to use this function 1. Select the MOVIE CLIP mode by pressing the M (Mode) button and press the menu button. Press the Left/Right Stabilizer Off button to select the [Stabilizer] menu. On 2. Select a desired sub menu by pressing the Up/Down button and press the OK button.
Starting play mode ■ Turn the camera on and select Play mode by pressing the play mode button ( The camera can now play back the images stored in the memory. ). ■ You can set up the PLAY mode function by using the camera buttons and LCD monitor. ■ If the memory card is inserted in the camera, all the camera functions apply only to the memory card. ■ If the memory card is not inserted in the camera, all the camera functions apply only to the internal memory. ● Playing back a still image 1.
Starting play mode ● Playing back a movie clip Steps from 1-2 are the same as those to play back a still image. 3. Select the recorded movie clip that you want to play back by using the LEFT/RIGHT button. If you select a movie clip, the movie clip indicator ( ) will be displayed on the LCD monitor. 4. Press the play & pause button ( ) to play back a movie clip file. - To pause a movie clip file while playing it back, press the play & pause button again.
Starting play mode ■ On camera movie trimming : You can extract desired frames of movie clip during the movie clip play back. ● If the running time is under 10 seconds, the movie clip can’t be trimmed. 1. Select a desired movie clip in the play mode. 2. Play back the movie clip by pressing the Play & Pause button. 3. Press the Pause button at the point of the movie clip that you want to start extracting. 4. Press the T button.
Starting play mode ● Playing back a recorded voice Steps from 1-2 are the same as those to play back a still image. 3. Select the recorded voice that you want to play back by using the LEFT/RIGHT button. If you select a recorded voice file, the voice indicator ( ) will be displayed on the LCD monitor. 4. Press the play & pause button ( ) to play back a recorded voice file. - To pause a recorded voice file, while playing it back, press the play & pause button again.
LCD monitor indicator ■ The LCD monitor displays shooting information about the displayed image. ⑦ ① ② ③ ④ ⑤ ⑥ No. Description 1 Play mode - 2 Battery p.18 3 File Type - 4 Voice memo p.69 5 Protect indicator p.81 6 DPOF indicator p.85 7 Folder name and Stored image number Size Av Tv ISO Flash Date 《66》 : : : : : : 2592X1944 F3.5 1/60 100 Off 2005/05/01 Icon Page 100-0009 Size Av Tv ISO Flash : 2592X1944 : F3.
Using the camera buttons to adjust the camera ■ In Play mode, you can use the buttons on the camera to conveniently set up the Play mode functions. Play mode button ■ If you have turned on the camera by pressing the POWER button, you can press the PLAY MODE button once to switch to Play mode and press it (Under 1 Sec.) again to switch to Recording mode. ■ You can turn the power on with the play mode button. The camera is turned on in play mode. Press the play mode button (Under 1 Sec.
Thumbnail( ) / Enlargement( ) button ■ You can view multiple pictures, enlarge a selected picture, and crop and save a selected area of an image. ● Thumbnail display 1. While an image is displayed full screen, press the thumbnail button. 2. The thumbnail display will highlight the image that had been showing at the time the thumbnail mode was selected. 3. Press the 5 function button to move to a desired image. 4. To view an image separately, press the enlargement button.
Thumbnail( ) / Enlargement( ) button ● The maximum enlargement rate in proportion to the image size. Image size 2592 2272 2048 1600 1024 640 Maximum enlargement rate X10.1 X8.8 X8.0 X6.2 X4.0 X2.5 ● Trimming : You can extract part of the image that you want and save it separately. 1. Select an image that you want to enlarge and press the enlargement button. 2. Different parts of the image can be viewed by pressing Trimming? Trimming the 5 function button. Cancel 3.
Voice ( ) memo / Up button 3. Press the shutter button to start recording and voice will be recorded to the still image for 10 seconds. While the voice is recording, the recording status window will be displayed as shown alongside. 4. The recording can be stopped by pressing the shutter button again. 5. The ( ) icon will be displayed on the LCD monitor after voice memo recording has finished. - Voice memos can’t be recorded onto movie clip files.
Delete ( ) button ■ This deletes images stored on the memory card. ● Deleting Images in Play Mode 1. Select an image that you want to delete by pressing the LEFT / RIGHT button and press the DELETE( ) button. 2. A message will display as shown alongside on the LCD monitor. 3. Select the submenu values by pressing the UP/DOWN button and then press the OK button. If [Delete] is selected : deletes the selected images. If [Cancel] is selected : cancels "Delete Image".
Left / Right / Menu / OK button ■ LEFT / RIGHT/ MENU/ OK buttons activate the following. - LEFT button : While the menu is showing, press the LEFT button to select the menu tab to the left of the cursor. - RIGHT button : While the menu is showing, press the RIGHT button to select the menu tab to the right of the cursor, or to move an secondary menu. - MENU button : When you press the MENU button, the play mode menu will be displayed on the LCD monitor.
Album button ■ You can organise the captured still images into albums by using the Album button. ■ This camera has 8 albums and each album can take up to 100 images. ■ The album menu loading time depends on the memory card type. ■ How to use the album ● Selecting the album 1. In the play mode, press the Album button. 2. Select the [Select] menu by pressing the Up/Down button and press the Right button. Select Slide Add Remove Exit:MENU 3.
Album button 3. Select the still images you wish to add by pressing the Up/Down/Left/Right buttons and press the Zoom T button. marks are displayed on the selected images. ※ To cancel the selection, press the Zoom T button again. Select Slide Add Remove Select:T 4. Press the OK button and a confirmation window will display. Select a desired sub menu by pressing the UP/ DOWN button and press the OK button. - [Add] : Inserts the selected images into the album. - [Cancel] : Cancels the inserting images.
Album button ● Playing back the albums ◎ Playing back all of the albums 1. Select [All] menu and press the OK button. All of the albums will be selected. 2. Select [Slide] menu by pressing the Up/Down button and press the Right button. ※ You can select [Start], [Interval], [Repeat] and [Effect] menus. - [Start] : Start the slide show - [Interval] : Set the slide show play interval - [Repeat] : Choose to repeat the slide show after finishing the first cycle.
Setting up the play back function using the LCD monitor ■ PLAY mode functions can be changed by using the LCD monitor. In the PLAY mode, pressing the MENU button displays the menu on the LCD monitor. The menus you can set up in Play mode are as follows. To capture an image after setting up the play menu, press the PLAY mode button or shutter button. Menu tab Main menu Slide Sub menu Secondary menu Start - Interval 1, 3, 5, 10sec Repeat Off / On Page p.
Setting up the play back function using the LCD monitor Menu tab Main menu DPOF Sub menu Secondary menu Standard Select/ All Pics/ Cancel Index No/ Yes Size Select/ All Pics/ Cancel No - Yes - Copy to Card Page p.85 p.88 ■ This menu is available while the camera is connected to a PictBridge supporting printer (direct connection to the camera, sold separately) with a USB cable. Menu tab Main menu Sub menu Secondary menu One Pic - All Pics - Images No - Yes - Auto Set Page p.
Setting up the play back function using the LCD monitor Menu tab Main menu Sub menu Secondary menu Page Auto Plain Type Photo Fastphoto Auto Draft Quality Normal Custom Set p.91 Fine Auto Date Off On Auto File Name Off On Standard - Index - Print DPOF Print Reset No - Yes - No - Yes - ※ Menus are subject to change without prior notice. 《78》 p.92 p.92 p.
Starting the slide show ■ Images can be displayed continuously at pre-set intervals. You can view the slide show by connecting the camera to an external monitor. 1. Press the play mode button and press the menu button. 2. Press the LEFT/ RIGHT button and select the [Slide] menu tab. ● Start the slide show : The slide show can start only in the [Start] menu. 1. Use the Up/Down buttons to select the [Start] menu. 2. Press the OK button to start the slide show.
Starting the slide show ● Configure slide show effects: Unique screen effects can be used for the slide show. 1. Select the [Effect] sub menu by pressing the UP/ DOWN button and press the RIGHT button. Slide 2. Use the Up/Down Button to select the type of effect. Start Cancel Interval Effect 1 [Cancel] : Normal display. Repeat Effect 2 Effect Effect 3 [Effect 1] : Image is displayed slowly. Effect 4 [Effect 2] : Image is displayed slowly from the centre Back:◀ Set:OK outwards.
Protecting images ■ This is used to protect specific shots from being accidentally erased (Lock). It also unprotects images that have been previously protected (Unlock). ● Protecting Images 1. Press the play mode button and press the menu button. 2. Press the LEFT/ RIGHT button and select the [Protect] menu tab. 3. Select a desired sub menu by pressing the UP/ DOWN button and press the OK button. [Select ] : Selection window for an image to be protected/released is displayed.
Deleting images ■ Of all the files stored in the memory card, the unprotected files in the DCIM subfolder will be deleted. Remember that this will permanently delete unprotected images. Important shots should be stored on a computer before deletion takes place. The startup image is stored in the camera's internal memory (i.e., not on the memory card) and it will not be deleted even if you delete all files on the memory card. ● Deleting images 1. Press the play mode button and press the menu button. 2.
Resize ■ Change the resolution (size) of pictures taken. Select [User image] to save an image to be the start-up image. The resized image will have a new file name. 1. Press the play mode button and press the menu button. 2. Press the LEFT/ RIGHT button and select the [Resize] menu tab. 3. Select a desired sub menu by pressing the UP/ DOWN button and press the OK button.
Effect ■ By using the camera’s digital processor, it is possible to add special effects to your images. 1. Press the play mode button and press the menu button. 2. Press the LEFT/ RIGHT button and select the [Effect] menu tab. B&W Sepia 3. Select a desired sub menu by pressing the UP/ DOWN Red Green button. Blue [B & W] : Captured images will be stored in black and Exit:MENU white [Sepia] : Captured images will be stored in a sepia tone (a gradient of yellowish brown colours).
Rotating an image ■ You can rotate the stored images by various degrees. Once the playback of the rotated picture is finished, it will switch back to the original state. 1. Press the play mode button and press the menu button. 2. Press the LEFT/ RIGHT button and select the [Rotate] menu tab. 3. Select a desired sub menu by pressing the UP/ DOWN button.
DPOF : Standard ■ This function allows you to embed print quantity information on a stored image. 1. Press the play mode button and press the menu button. 2. Press the LEFT/ RIGHT button and select the [DPOF] menu tab. 3. Select the [Standard] menu by pressing the UP/ DOWN button and press the RIGHT button. 4. Select a desired sub menu by pressing the UP/ DOWN button and press the OK button. [Select] : Selection window for an image to print is displayed. - Up/Down/Left/Right : Select an image to print.
DPOF : Print size ■ You can specify the print size when printing images stored on the memory card. The [Size] menu is available only for DPOF 1.1 compatible printers. ● Setting the Print Size 1. Press the play mode button and press the menu button. 2. Press the LEFT/ RIGHT button and select the [DPOF] menu tab. 3. Select the [Size] menu by pressing the UP/ DOWN button and press the RIGHT button. 4. Select a desired sub menu by pressing the UP/ DOWN button and press the OK button.
Copy To Card ■ This enables you to copy image files to the memory card. ● Copying to the Memory Card 1. Press the play mode button and press the menu button. 2. Select the [Copy to Card] menu tab by pressing the LEFT/ Copy To Card RIGHT button. No Yes 3. Select a desired sub menu by pressing the UP/ DOWN button and press the OK button. - [No] : Cancels "Copy to Card". Exit:MENU - [Yes] : All images saved in the internal memory are copied to the memory card after the [Processing!] message is displayed.
PictBridge ■ You can use the USB cable to connect this camera to a printer that supports PictBridge (sold separately) and print the stored images directly. Movie clips and voice files cannot be printed. ● Setting up the camera for connection with the printer 1. In any mode with the exception of Voice Recording mode, press the MENU button. 2. Press the LEFT/ RIGHT button and select [Setup] menu tab. 3. Select [USB] menu by pressing the UP/ DOWN button and press the RIGHT button. 4.
PictBridge : Picture Selection ■ Easy printing When you connect the camera to printer in the Play back mode, you can print a picture easily. - Pressing the shutter button : Currently displayed image will be printed with the printer’s default setting. - Pressing the Left / Right button : Selects a previous / next image. 141-0001 ◀ ▶ Print:Shutter ■ Select pictures to print 1. The [Images] menu will appear. 2.
PictBridge : Print Setting ■ AUTO SET 1. Use the LEFT and RIGHT buttons to select the [Auto Set] menu tab. 2. Use the UP and DOWN buttons to select the desired submenu value, and then press the OK button. [No] : [Custom Set] values are kept. [Yes] : All values in the [Custom Set] are automatically changed. Auto Set No Yes Move: ■ Custom Set : You can select the Paper Size, Print Format, Paper Type, Print Quality, Date Print, and File Name Print menus for printed pictures. 1.
PictBridge : Printing ■ Printing Pictures 1. Use the LEFT and RIGHT buttons to select the [Print] menu tab. 2. Use the UP and DOWN buttons to select the desired submenu value, and then press the OK button. [Standard] : Print the pictures stored in the memory card in set numbers. One picture is printed on one piece of paper. [Index] : Print multiple images on one sheet of paper. 3. The screen shown on the right will appear and the picture will be printed.
PictBridge : RESET ■ Initialises user-changed configurations. 1. Use the LEFT and RIGHT buttons to select the [Reset] menu tab. 2. Use the UP and DOWN buttons to select the desired submenu value, and then press the OK button. If [No] is selected : Settings will not be reset. If [Yes] is selected : All print and image settings will be reset. Reset No Yes Move: ※ Default print setting varies depending on the printer manufacturer.
Setup menu ■ In this mode, you can set up basic settings. You can use the setup menu in all camera modes, except Voice Recording mode. The items indicated by are default settings. Menu tab Main menu Sub menu Secondary menu Series - Reset - 1, 3, 5, 10 min - p.95 File Power Save Page p.96 ENGLISH 한국어 FRANÇAIS DEUTSCH ESPAÑOL ITALIANO 日本語 Language P”CCK»… PORTUGUÊS DUTCH DANSK SVENSKA SUOMI p.
Setup menu Menu tab Main menu Sub menu Secondary menu Off - On - Dark - Normal - AF Lamp LCD p.100 Bright - NTSC - PAL - Off, 0.5, 1, 3 sec - No - Yes - Video Out Quick View Reset Page p.100 p.101 p.103 p.103 ※ Menus are subject to change without prior notice. File name ■ This function allows the user to select the file naming format. ● Assigning File Names 1. In any mode with the exception of Voice Recording mode, press the MENU button. Setup 2.
File name INFORMATION ● The first stored folder name is 100SSCAM, and the first file name is SSL10001. ● File names are assigned sequentially from SSL10001 → SSL10002 → ~ → SSL10099. ● The folder number is assigned sequentially from 100 to 999 as follows: 100SSCAM → 101SSCAM → ~ → 999SSCAM. ● The files used with the memory card conform to the DCF(Design rule for Camera File systems) format.
Language ■ There is a choice of languages that can be displayed on the LCD monitor. Even if the battery and AC charger are removed and inserted again, the language setting will be preserved. ● Setting Language 1. In any mode with the exception of Voice Recording mode, press the MENU button. Setup File ENGLISH 2. Press the LEFT/ RIGHT button and select the [Setup] menu tab. Power Save 한국어 3.
Setting up the Date / Time / Date type ■ You can change the date and time that will be displayed on the captured images and set up the date type. ● Setting Date/Time & Selecting Date Format 1. In any mode with the exception of Voice Recording mode, press the MENU button. Setup File 2. Press the LEFT/ RIGHT button and select the [Setup] ▲ Power Save menu tab. 05/ 05/ 01 13:01 Language ▼ Format 3. Select the [Date&Time] menu by pressing the UP/ DOWN yy/mm/dd Date&Time button and press the RIGHT button.
Sound ■ If you set the operation sound to ON, various sounds will be activated for camera startup, when button are pressed, and if there is a card error, so that you can be aware of the camera operation status. ● Setting Operation Sounds 1. In any mode with the exception of Voice Recording mode, press the MENU button. 2. Press the LEFT/ RIGHT button and select the [Setup] menu tab. 3. Select the [Sound] menu by pressing the UP/ DOWN button and press the RIGHT button. 4.
Auto Focus lamp ■ You can turn on and off the Auto Focus lamp ● How to set up the lamp 1. In any mode with the exception of Voice Recording mode, press the MENU button. 2. Press the LEFT/ RIGHT button and select the [Setup] menu tab. 3. Select the [AF Lamp] menu by pressing the UP/ DOWN button and press the RIGHT button. 4. Select a desired sub menu by pressing the UP/ DOWN button and press the OK button. If [Off] is selected : The AF lamp will not light up. If [On] is selected : The AF lamp will light up.
Selecting Video out type ■ The Movie output signal from the camera can be NTSC or PAL. Your choice of output will be governed by the type of device (monitor or TV, etc.) to which the camera is connected. PAL mode can support only BDGHI. ● Setting the Video Out Type 1. In any mode with the exception of Voice Recording mode, press the MENU button. 2. Press the LEFT/ RIGHT button and select the [Setup] menu tab. 3. Select the [Video Out] menu by pressing the UP/ DOWN button and press the RIGHT button. 4.
Selecting Video out type INFORMATION ● NTSC : U.S.A, Canada, Japan, South Korea, Taiwan, Mexico. ● PAL : Australia, Austria, Belgium, China, Denmark, Finland, Germany, U.K., Holland, Italy, Kuwait, Malaysia, New Zealand, Singapore, Spain, Sweden, Switzerland, Thailand, Norway. ● When using a TV as an external monitor, you will need to select the external or AV channel of the TV. ● There will be a digital noise on the external monitor, but it is not a malfunction.
Quick view ■ If you enable Quick View before capturing an image, you can view the image you just captured on the LCD monitor for the duration set in the [Quick View] setup. Quick view is possible only with still images. ● Setting Quick View 1. In any mode with the exception of Voice Recording mode, press the MENU button. Setup 2. Press the LEFT/ RIGHT button and select the [Setup] USB Off AF Lamp 0.5 sec menu tab. LCD 1 sec Video Out 3 sec 3.
Setting up the Mycam menu ■ You can set up a start up image, start up sound and shutter sound. Every camera working mode (with the exception of Voice recording mode) has the MyCAM menu. The items indicated by are default settings. Menu tab Main menu Sub menu Page Off LOGO User Image 1 User Image 2 Off Sound 1 Sound 2 Sound 3 Off Sound 1 Sound 2 Sound 3 S.Image p.104 S.Sound p.105 SH.Sound p.105 ※ Menus are subject to change without prior notice.
Start up sound ■ You can select the sound that is activated whenever the camera is turned on. ● Setting the Startup Sound 1. In any mode with the exception of Voice Recording mode, press the MENU button. 2. Press the LEFT/ RIGHT button and select the [Mycam] menu tab. 3. Select the [S.Sound] menu by pressing the UP/ DOWN button and press the RIGHT button. 4. Select a desired sub menu by pressing the UP/ DOWN button and press the OK button. 5. Press the menu button twice and the menu will disappear.
Important notes Be sure to observe the following precautions! ■ This unit contains precision electronic components. Do not use or store this unit in the following locations. - Areas exposed to severe changes in temperature and humidity. - Areas exposed to dust and dirt. - Areas exposed to direct sunlight or the inside of a vehicle in hot weather. - Environments where there is high magnetism or excessive vibration. - Areas with high explosives or highly flammable materials.
Important notes ■ Caution on Using the Lens - If the lens is subjected to direct sunlight, it could result in discoloration and deterioration of the image sensor. - Pay attention not to get fingerprints or foreign substances on the surface of the lens. ■ If the digital camera is not used for a long period, an electric discharge can occur. It is a good idea to remove the batteries and the memory card if you do not intend using the camera for an extended period of time.
Warning indicator ■ There are several warnings that may appear on the LCD display Card Error! ㆍMemory card error → Turn off the camera power and turn it on again → Insert the memory card again → Insert the memory card and format the memory card (p.97) Memory Error! ㆍInternal memory error → Turn off the camera power and turn it on again → Format the memory with the memory card removed. (p.
Warning indicator Low Light! ㆍWhen taking pictures in dark places → Take pictures in Flash Photography mode. Out Of Number ㆍWhen selecting too many printing pages in the PictBridge menu. → Select printing page within the limitation. Before contacting a service centre ■ Please check the following The camera doesn’t switch on ㆍThere is low battery capacity → Insert charged battery (p.
Before contacting a service centre Camera does not take images when pressing the Shutter button ㆍThere is insufficient memory capacity → Delete unnecessary image files ㆍThe memory card has not been formatted → Format the memory card (p.97) ㆍThe memory card is exhausted → Insert a new memory card ㆍThe memory card is locked → Refer to [Card Locked!] error message (p.108) ㆍThe camera’s power is off → Turn the camera power on ㆍThe battery are exhausted → Insert charged battery (p.14 ~ 18).
Before contacting a service centre The camera buttons do not operate ㆍCamera malfunction → Remove /re-insert battery and switch the camera on A card error has occurred while the memory card is in the camera.
Specifications 1/2.5" CCD Approx. 5.0 Mega-pixel Approx. 5.1 Mega-pixel SHD Lens f = 6.6 ~ 19.8mm (35mm film equivalent : 39 ~ 117mm) F 3.5 ~ F 4.5 Lens Still Image mode : 1.0X ~ 5.0X Digital Zoom Play mode : 1.0X ~ 10.1X (depends on image size) LCD Monitor 2.
Specifications Media File Format Image Size Storage Capacity (32MB) Image Play Type Editing Interface Power Source Dimensions (WxHxD) Weight Operating Temperature Operating Humidity Software Camera Driver Application Special Features Internal memory : Approx. 50MB flash memory External memory : SD card /MMC (Up to 1GB Guaranteed) Still Image : JPEG (DCF), EXIF 2.2, DPOF 1.1, PictBridge 1.
Software Notes Please ensure that you read the instruction manual carefully before use. ㆍThe attached software is a camera driver and image editing software tool for Windows. ㆍUnder no circumstances should all or part of either the software or the user manual be reproduced. ㆍCopyrights for software are licensed only for use with a camera. ㆍIn the unlikely event of a manufacturing fault, we will repair or exchange your camera.
About the software After inserting the CD-ROM provided with this camera into the CD-ROM drive, the following window should automatically run. Before connecting the camera to the PC, you should first install the camera driver. ■ Camera driver : This enables images to transfer between the camera and PC. This camera uses the USB Storage Driver as the camera driver. You can use the camera as a USB card reader.
About the software ■ Digimax Reader : Text recognition program. You can save an image file that was captured in the TEXT mode as a text file with this program. This software is only compatible with Windows. ■ PhotoImpression : Image editing program. You can edit or store still images that you download from the camera. This software is only compatible with Windows. INFORMATION ● Be sure to check the system requirements before installing the driver.
Setting up the application software To use this camera with a PC, install the application software first. After this has been done, the stored images in the camera can be moved to the PC and can be edited by an image editing program. INFORMATION ● Close other programs before installing the application software. ● Before installing the application software, disconnect the USB connection. You can visit the Samsung web-site through the internet. http://www.samsungcamera.com : English http://www.
Setting up the application software 4. If an error listed below takes place during the preview, click the [Install] button to install the XviD codec. - Only a voice plays back. - An error message displays and the movie clip does not play back. * A window shown alongside may display according to the system requirements. [Click !] 5. The XviD codec installation window will be displayed as shown alongside. Click the [Next >] button. [Click !] 6. The Software License Agreement window will be displayed.
Setting up the application software 7. The XviD information window will display. Click the [Next >] button. [Click !] 8. The destination selection window will open. Click [Next >] button. To copy to the files to another folder, click [Browse...] and choose a folder you want. [Click !] 9. A window will open, asking you to choose a folder to which program icons will be added. Click [Next >] button.
Setting up the application software 11. The XviD codec is ready to install. Click the [Install] button. [Click !] 12. Installation is complete. Click the [Finish] button. [Click !] 13. A window where you can choose the program you want to install will appear. Click [Install]. For information on application software, please refer to page 115, 116. [Click !] INFORMATION ● If you select [Exit] at step 13, the application program installation will be cancelled. 14. The [Digimax Viewer 2.
Setting up the application software INFORMATION ● If you select [Cancel] at step 14, a window for installing Digimax Reader will be displayed. 15. The Software License Agreement window will be displayed. If you agree to this, click [Yes], the window will then move to the next step. If you disagree, click [No] and the installation program will be canceled. [Click !] 16. A destination selection window will open. Click [Next >]. To copy to the files to another folder, click [Browse..
Setting up the application software 19. A window will be displayed as shown alongside. Click the [INSTALL] button. - Check the [MANUAL] button. Instructions for using Digimax reader will be displayed. - Click the [EXIT] button and Digimax reader installation will be cancelled and a window for installing PhotoImpression will be displayed. [Click !] 20. A window will open. Click the [Next >] button. [Click !] 21. The Software License Agreement window will be displayed.
Setting up the application software 23. Digimax Reader Installation is completed. Click the [Finish] button and PhotoImpression installation will be started. The system will not reboot even if the [Yes, I want to restart the computer now] option is selected. * The frame that appears may be different to that shown according to the system requirements. [Click !] 24. The PhotoImpression installation window will be displayed as shown alongside. Click the [OK] button. [Click !] 25.
Setting up the application software 27. A destination selection window will open. Click [Next >]. To copy to the files to another folder, click [Browse...] and choose a folder you want. [Click !] 28. The [Select Components] window will appear. Click [Next >] button. [Click !] 29. A window will open, asking you to choose a folder to which program icons will be added. Click [Next >] button. If you want to add the program icons to a different folder, choose another folder, and then click [Next >] button.
Setting up the application software 31. To apply changes, you must restart the computer. Select [Yes, I want to restart my computer now], and then click [Finish]. [Click !] 32. After restarting the computer, connect the PC to the camera with the USB cable. 33. Turn the camera power on. [Found New Hardware Wizard] will open and the computer will recognise the camera. * If you have ever installed an image viewer program or your OS is Windows XP, an image viewer program will open.
Setting up the application software INFORMATION ● If you have installed the camera driver, [Found New Hardware Wizard] may not open. ● On a Windows 98 or 98 SE system, the Found New Hardware Wizard dialog box opens and a window asking you to select a driver file may appear. In this case, specify "USB Driver" in the CD supplied. (for Windows 98 and 98 SE). ● Before connecting the camera to the PC, You should first install the camera driver. ● After installing the camera driver, you have to restart your PC.
Starting PC mode • If you connect the USB cable to a USB port on your PC and then turn on the power, the camera will automatically switch to "computer connection mode". • In this mode, you can download stored images to your PC through the USB cable. ■ Connecting the camera to a PC 1. In any mode with the exception of Voice Recording mode, press the MENU button. 2. Press the LEFT/ RIGHT button and select the [Setup] menu tab. 3.
Starting PC mode ■ Downloading stored images You can download the still images stored on the camera to your PC's hard disk and print them or use a photo editing software to edit them. 1. Connect the camera to your PC with the USB cable. 2. On your computer's desktop display, select [My computer] and double click [Removable Disk → DCIM → 100SSCAM]. The image files will then be displayed. 3. Select an image and press the right mouse button. 4. A pop-up menu will open. Click [Cut] or [Copy] menu.
Starting PC mode 6. Press the right mouse button and a pop-up menu will open. Click [Paste]. 7. An image file is transferred from the camera to your PC. - By using [Digimax Viewer], you can see the stored images in the memory directly on the PC monitor and you can copy or move the image files.
Removing the USB Driver for Windows 98SE ■ To remove the USB driver, refer to the process shown below. 1. Trace [Start → Settings] and click [Control Panel]. 2. Double-click [Add/Remove programs]. 3. The [Add/Remove Programs Properties] window will open. Click [Digimax i5] and click the [Add/Remove] button. [Click !] 4. Uninstallation is complete. Click the [Finish] button and the window will disappear.
Removable Disk ■ To use this camera as a Removable Disk, install (p.117) the USB Driver. 1. Before turning the camera power on, connect the camera to the PC with the USB cable. 2. Click [Removable Disk] under [My computer] or [Windows Explorer]. 3. Image files stored in the Removable Disk (DCIM → 100SSCAM) can be transferred to the PC. INFORMATION Important information whilst using the Removable Disk ● The [Removable Disk] indicator will not show when the camera power is off or the USB cable is removed.
Removing the removable disk ■ Windows 98SE 1. Check whether the camera and PC are transferring a file. If the camera status lamp blinks, you have to wait until the lamp illuminates. 2. Unplug the USB cable. ■ Windows 2000/ME/XP (The illustrations may be different from the real display in accordance with the Windows O/S.) 1. Check whether the camera and PC are transferring a file. If the camera status lamp blinks, you have to wait until the lamp illuminates. 2.
Removing the removable disk 6. A [Unplug or Eject Hardware] window will open. Click the [Close] button and the removable disk will be removed safely. 7. Unplug the USB cable. [Click !] Setting up the USB Driver for MAC 1. A USB Driver for MAC is not included with the software CD as MAC OS supports the camera driver. 2. Check the MAC OS. You can check the MAC OS version during MAC OS start-up. This camera is compatible with MAC OS 9.2 ~ 10.3. 3.
Digimax Viewer 2.1 ■ This software is only compatible with Windows. 1. To open Digimax Viewer, click the [Start → Programs → Samsung → Digimax Viewer 2.1 → Digimax Viewer 2.1 ] and Digimax Viewer 2.1 will then open. 2. If the [Auto Launch] option is selected, this program will be executed automatically with recognizing the camera. 3. You can easily use the Digimax viewer 2.1 program as it offers a FILE menu and TOOL bar. And, you can use the pop up menu. Click an image and press the right mouse button.
Digimax Reader ■ Digimax Reader is a Text recognition program. You can save an image file that is captured in the Text mode, as a text file with this program. This software is only compatible with Windows. ■ To start the program, click [Start → Programs → Digimax Reader Eng]. The following screen will appear. ■ How to use the Digimax Reader 1. Connect the camera and the PC with a USB cable and download the images that were stored in the camera to the PC.
Digimax Reader 4. Select the image you want to save as a text file. * Only an image that was taken with SAMSUNG camera can be opened. 5. Click the Area Analysis( image. ) icon to scan the 6. Part of the image you selected will be displayed as shown. 7. Click the Character Recognition( ) icon. The part selected in the previous step will be recognized as text. 8. To save the section as a text, click the Save( icon. A window as shown alongside will be displayed.
Digimax Reader 9. Select a file type that you want to. Selectable file type : *.TXT, *.HWP, *.DOC, *.RTF INFORMATION ● To get an image that can be recognized as a text : - Characters have to be clear - The subject need to be centered. - Avoid the camera shake to get a good image. ● Refer to the [Help] menu in Digimax Reader for further information. Using PhotoImpression ㆍWith PhotoImpression, you can edit or store still images that you downloaded from the camera.
Using PhotoImpression ㆍYou can use PhotoImpression to perform the following tasks. ■ Command Button Button Description Imports a picture from an album, a source folder, or the camera/scanner, or captures screen shots of what is being viewed on the current monitor. Selects Cut, Resize, Edit Image, Insert Text, Enhance Picture, Insert Effects, or Layer. Performs Insert Frame, Insert Borders, Insert Calendar, Insert Greeting Cards, Insert Template, or Connect with Other Software.
FAQ ■ Please check the following if the USB connection malfunctions. [Case 1] The camera power is off. → Turn the camera power on. [Case 2] USB Driver is not installed correctly. → Install the USB Driver correctly. Refer to page 117. [Case 3] The USB cable is not connected or you are using a cable with an incorrect specification. → Use a USB cable with the correct specification. [Case 4] The camera is not recognized by your PC.
FAQ There must be USB Host Controller and USB root hub under [Universal Serial Bus controllers]. In addition, double-click on the USB Universal Host Controller and the USB Root Hub to check if the Device Status states "This device is working properly". If the Device Status says the device is "not working properly", click the "Driver" tab and then click [Update Driver] or [Reinstall Driver]. → When all the conditions mentioned above are met, the computer can support the USB interface.
FAQ ■ When the movie clip doesn’t play back on the PC ※ When the movie clip recorded by the camera doesn’t play back on the PC, the causes are mostly due to the codec installed on the PC. ● When codec for play back the movie clip isn’t installed → Install the codec as listed below. [Installing codec for Windows] 1) Insert the CD provided with the camera 2) Run the windows explorer and select [CD-ROM drive:\XviD] folder and click the XviD codex-1[1].1.0.exe file.
FAQ ● If a PC (Windows 98) stops responding while the camera and PC are connected repeatedly → If a PC (Windows 98) is turned on for a long time and connect the camera repeatedly, the PC may not recognise the camera. In this case, re-start the PC. ● If a PC connected with the camera stops responding while Windows is starting. → In this case, disconnect the PC and the camera and Windows will start. If the problem happens continuously, set the Legacy USB Support to disable and re-start the PC.
MEMO 《143》
MEMO 《144》
MEMO 《145》
MEMO 《146》
MEMO 《147》
SAMSUNG TECHWIN CO., LTD. OPTICS & DIGITAL IMAGING DIVISION 145-3, SANGDAEWON 1-DONG, JUNGWONGU, SUNGNAM-CITY, KYUNGKI-DO, KOREA 462-121 TEL : (82) 31-740-8086,8088, 8090, 8092, 8099 FAX : (82) 31-740-8398, 8111 www.samsungcamera.com SAMSUNG OPTO-ELECTRONICS AMERICA, INC. HEADQUARTERS 40 SEAVIEW DRIVE, SECAUCUS, NJ07094, U.S.A. TEL : (1) 201-902-0347 FAX : (1) 201-902-9342 WESTERN REGIONAL OFFICE 18600 BROADWICK ST., RANCHO DOMINGUEZ, CA 90220, U.S.A. TEL : (1) 310-900-5263/5264 FAX : (1) 310-537-1566 www.
