SAMTRON 96BDF / 98BDF
User’s Manual Site Map Automatic Manual 2
User’s Manual Safety Instructions Warning / Caution Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment.
User’s Manual 4 Safety Instructions Power When not used for extended periods of time, set your PC to DPMS. If using a screen saver, set it to the active screen mode. If the size of your monitor is small, or if the same image is present for long periods of time, you may see afterimages due to damage to the flourescent substance on the inside of the CDT. ● Do not use a damaged or loose plug. ◆ This may cause an electric shock or fire.
User’s Manual Safety Instructions ● Disconnect the plug from the outlet during storms or lightening or if it is not used for a long period of time. ◆ Failure to do so may cause an electric shock or fire. ● Do not connect too many extension cords or plugs to an outlet. ◆ This may cause a fire.
User’s Manual 6 Safety Instructions Installation ● Do not cover the vents on the monitor cabinet. ◆ Bad ventilation may cause a breakdown or fire. ● Put your monitor in a location with low humidity and a minimum of dust. ◆ An electric short or fire could result inside the monitor. ● Do not drop the monitor when moving it. ◆ This may cause damage to the product or human body. ● Place the monitor on a flat and stable surface. ◆ The monitor can cause injury by falling. ● Set down the monitor carefully.
User’s Manual Safety Instructions Cleaning When cleaning the monitor case or the surface of the CRT, wipe with a slightly moistened, soft fabric. Do not clean Flat monitor with water. Use a water-diluted mild detergent. (Some detergents contain significant amounts of alcohol-based solvents, which can damage (color change) or crack the monitor case. The antiglare/anti-static surface coating on the CDT may also be affected.) Dilute the detergent (1:10 ratio) with water before using.
User’s Manual Safety Instructions Other ● Do not remove cover(or back). No user serviceable parts inside. ◆ This may cause an electric shock or a fire. ◆ Refer servicing to qualified service personnel. ● If your monitor does not operate normally - in particular,if there are any unusual sounds or smells coming from it - unplug it immediately and contact an authorized dealer or service. ◆ This may cause an electric shock or a fire. ● Do not place any heavy objects on the monitor.
User’s Manual ● Do not move the monitor right or left by pulling only the wire or the signal cable. ◆ This may cause a breakdown, electric shock or a fire due to damage to the cable. ● Never insert anything metallic into the monitor openings. ◆ This may cause an electric shock, fire or injury. ● Keep the monitor away from any magnetic substances.. ◆ This may cause discoloring or distortion of the image.
User’s Manual Introduction Unpacking ■ Monitor and Stand ■ Power Cord ■ Stand ■ Quick Setup Guide (Your monitor is shipped with the base detached.) Please make sure the following items are included with your monitor. If any items are missing, contact your dealer.
User’s Manual 11 Introduction Front 1. 2,3. 4. 5. 6. Note: Exit button Adjust buttons Menu button Power indicator Power button : Use this button to Exit the active menu or the OSD. : These buttons allow you to highlight and adjust items in the menu. : Use this button to open the OSD and activate a highlighted menu item. : Indicates normal or Power Saving Mode. : Use this button to turn the monitor on and off.
User’s Manual 12 Introduction Rear 1. Power port : Connect the power cord for your monitor to the power port on the back of the monitor. 2.Signal cable :Connect the end of the signal cable to your computer's video port (video board,video card or graphics card). Note: See Connecting Your Monitor for further information regarding cable connections. (The configuration at the back of the moniter may vary from product to product.) Bottom 1.
User’s Manual 13 Setup Connecting Your Monitor 1.Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. 2.Connect the end of the signal cable to your computer's video port(video board, video card or graphics card). 3.If you are using a Macintosh computer, connect the cable to a Macintosh adapter, and set the pins on your adapter(Adapter not included). A PC-compatible computer does not need an adapter. 4.
User’s Manual Setup Installing the Video Driver When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating sys tem to another. Follow the directions as appropriate for the operating system you have. Windows ME 1. Insert CD into the CD-ROM driver. 2. Click "Windows ME Driver". 3. Choose your monitor model in the model list, then click the "OK" button.
User’s Manual Setup Installing the Video Driver 4. Click the "Install" button in the "Warning" window. 5. Monitor Driver installation is completed. Windows XP/2000 1. Insert CD into the CD-ROM driver. 2. Click "Windows XP/2000 Driver". 3. Choose your monitor model in the model list, then click the "OK" button.
User’s Manual 16 Setup Installing the Video Driver 4. Click the "Install" button in the "Warning" window. 5. If you can see following "Message" window, then click the "Continue Anyway" button. Then click "OK" button. This monitor driver is under certifying MS logo, and this installation don't damage your system. The certifide driver will be posted on Samsung Monitor Homepage. 6. Monitor Driver installation is completed.
User’s Manual Setup Installing the Video Driver When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating sys tem to another. Follow the directions as appropriate for the operating system you have. Microsoft® Windows® XP Operating System 1. Insert CD into the CD-ROM driver. 2. Click "Start" —> "Control Panel" then click the "Appearance and Themes" Icon. 3.
User’s Manual Setup Installing the Video Driver 4. Click the "Properties" button on the "Monitor" tab and select "Driver" tab. 5. Click "Update Driver.." and select "Install from a list or.." then click "Next" button. 6. Select "Don't search ,I will.." then click "Next" and then click "Have disk".
User’s Manual Setup Installing the Video Driver 7. Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next" button. 8. If you can see following "Message" window, then click the "Continue Anyway" button. Then click "OK" button. This monitor driver is under certifying MS logo,and this installation don't damage your system.The certified driver will be posted on Samsung Monitor Homepage. 9.
User’s Manual 20 Setup Installing the Video Driver 10. Monitor driver installation is completed. Microsoft® Windows® 2000 Operating System When you can see "Digital Signature Not Found" on your monitor, follow these steps. 1. Choose "OK" button on the "Insert disk" window. 2. Click the "Browse" button on the "File Needed" window. 3. Choose A:(D:\Driver) then click the "Open" button and then click "OK" button. How to install 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Click "Start" , "Setting" , "Control Panel".
User’s Manual 21 Setup Installing the Video Driver Microsoft® Windows® Millennium Operating System 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Click "Start" , "Setting" , "Control Panel". Double click "Display" icon. Select the "Settings" tab and click "Advanced Properties" button. Select the "Monitor" tab. Click the "Change" button in the "Monitor Type" area. Choose "Specify the location of the driver". Choose "Display a list of all the driver in a specific location.." then click "Next" button.
User’s Manual Setup Tilt/Swivel Base Installation 1. Tilt/Swivel Base With the built-in pedestal, you can tilt and/or swivel the monitor for the most comfortable viewing angle. Note: The base is detachable. Your monitor is shipped with the base detached.
User’s Manual Setup 2. Attaching the Base If your monitor was supplied with the base detached, attach the base as follows. 1. Place the monitor upside-down on a flat work surface. 2. Align the tabs on the base with the corresponding slots on the bottom of the monitor. Do not bend the snap. 3. Press the base onto the monitor until the tabs are fully engaged in the slots. 4. Push the base toward the front of the monitor until the release latch clicks into the locked position.
User’s Manual Setup 3. Removing the Base 1. Turn off the monitor and unplug it from the electrical outlet. 2. Place the monitor upside down on a stable, flat work surface. 3. Squeeze and pull up on the release latch on the base. 4. Push the base toward the back of the monitor and lift up to remove the base.
User’s Manual On Screen Display (OSD) Menu System 1 Use this button to open the OSD and activate a highlighted menu item. 2.3 Use these buttons to highlight and adjust items using the On-Screen Display. These buttons are also direct access buttons for the contrast and brightness feature. 4 Use this button to Exit the active menu or the OSD.
User’s Manual Troubleshooting Chek List Note : Before calling for service, check the information in this section to see if you can solve the problem yourself. If you do need assistance, please call the phone number on the warranty card, the phone number on the Information section or contact your dealer. Symptom No Images on the screen. I cannot trun on the monitor. Chek List Solution Is the power cord connected properly? Check the power cord connection and supply.
User’s Manual Troubleshooting Symptom The image on the screen is shaking. Chek List Solution Check the monitor configuration to see if it is in Interlace Mode. (Interlace Mode: Vertical frequency 43Hz, 87Hz(i), etc) The signal from the video card exceeds the maximum resolution and frequency of the monitor. Are there any magnetic products such as a high voltage wire near by? Move the monitor away from anything that can create a strong magnetic field.
User’s Manual Troubleshooting Symptom The screen is partialy distorted. LED is blinking but no images on the screen. Chek List Are there any magnetic products such as an adapter, speaker or a high voltage wire near the monitor? Is the frequency properly adjusted when checking the Display Timing on the menu? Solution Enter the OSD and perform a 'Degauss'. Keep the monitor away from any magnetic products. Adjust the frequency properly by referring to the video card manual and the Preset Timing Modes.
User’s Manual Troubleshooting Check the following items if there is trouble with the monitor. 1. Check if the power cord and the cable are properly connected to the computer. 2. Check if the computer beeps more than 3 times when booting. (If it does, request an after-service for the main board of the computer.) 3. If you installed a new video card or if you assembled the PC, check if the installed the adapter (video) driver and the monitor driver. 4.
User’s Manual 37 Troubleshooting Q&A Question How can I change the frequency? Answer Frequency can be changed by reconfiguring the video card. Note that video card support can vary, depending on the version of the driver used. (Refer to the computer or the video card manual fordetails.) How can I adjust the resolution? Windows ME/XP/2000: Set the resolution at the Control Panel, Display, Settings. * Contact the video card manufacturer for details.
User’s Manual Troubleshooting Self-Test Feature Check A self-test feature is provided that allows you to check for proper monitor function. If your monitor and computer are properly connected but the monitor screen remains dark and the power indicator is blinking, run the monitor self-test by performing the following steps: Self-Test Feature Check 1. Turn off both your computer and the monitor. 2. Unplug the video cable from the back of the computer. 3. Turn on the monitor.
User’s Manual 39 Troubleshooting Self-Test Feature Check Warning Messages If there is something wrong with the input signal, a message appears on the screen or the screen goes blank although the power indicator LED is still on. The message may indicate that the monitor is out of scan range or that you need to check the signal cable. Environment The location and the position of the monitor may influence the quality and other features of the monitor. 1.
User’s Manual Specifications General Specifications General Model Name SAMTRON 96BDF Picture Tube Type 19" (48cm) DynaFlat (45.8cm viewable) Deflection angle 90° Dot Pitch 0.20mm (Horizontal) Screen type Silica coated with anti-electronic properties (TCO : Multilayer coating) Medium-short persistence phosphor. Maximum Resolution 1600 Dots, 1200 Lines Active Display Horizontal 13.85 ± 0.12 inch (352 ± 3 mm) Vertical 10.39 ± 0.
User’s Manual Specifications General Specifications General Model Name SAMTRON 98BDF Picture Tube Type 19" (48cm) DynaFlat (45.8cm viewable) Deflection angle 90° Dot Pitch 0.20mm (Horizontal) Screen type Silica coated with anti-electronic properties (TCO : Multilayer coating) Medium-short persistence phosphor. Maximum Resolution 1600 Dots, 1200 Lines Active Display Horizontal 13.85 ± 0.12 inch (352 ± 3 mm) Vertical 10.39 ± 0.
User’s Manual 41 Specifications Preset Timing Modes If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows. Display Mode Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) IBM, 640 x 480 31.469 59.940 25.175 -/- IBM, 720 x 400 31.
User’s Manual 42 Specifications PowerSaver This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor into a low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you move the computer's mouse or press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods.
User’s Manual Information Service ● SAMTRON SEOUL 15TH FL, JOONGANG DAILY NEWS BLDG. 7, SOONHWA-DONG,CHUNG-KU, SEOUL, KOREA, 100-759 TEL : (82-2) 727-3114 ● SAMTRON U.S.A SAMTRON COMPUTER PRODUCTS CUSTOMER SERVICE 400 Valley Road Suite 201, Mt. Arlington, NJ 07856 TEL : 973-601-6200, FAX : 973-601-6001 1-800-SAMTRON (1-800-726-8766) ● SAMTRON CANADA SAMSUNG ELECTRONICS CANADA INC.
User’s Manual Information Terms ● Dot Pitch The image on a monitor is composed of red, green and blue dots. The closer the dots, the higher the resolution. The distance between two dots of the same color is called the 'Dot Pitch'. Unit: mm ● Vertical Frequency The screen must be redrawn several times per second in order to create and display an image for the user. The frequency of this repetition per second is called Vertical Frequency or Refresh Rate.
User’s Manual Information Regulatory FCC Information | IC Compliance Notice | MPR II Compliance(Except SyncMaster 551v) European Notice (Europe only) | PCT Notice | VCCI TCO'95-Ecological requirements for personal computers (TCO applied model only) TCO'99-Ecological requirements for personal computers (TCO applied model only) FCC Information User Instructions The Federal Communications Commission Radio Frequency Interference Statement includes the following warning: Note: This equipment has been tested and
User’s Manual 46 Information IC Compliance Notice This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations of ICES-003. Cet appareil Numérique de classe B respecte toutes les exigences du Règlemont NMB-03 sur les équipements produisant des interférences au Canada. MPR II Compliance(Except SyncMaster 551v) This monitor complies with SWEDAC(MPR II) recommendations for reduced electric and magnetic fields.
User’s Manual Information TCO'95-Ecological requirements for personal computers (TCO applied model only) AB general requirements AB2 Written Eco-document acompanying the products Congratulations! You have just purchased a TCO'95 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and to the further development of environmentally-adapted electronic products.
User’s Manual Information TCO Development Unit 1996-11-29 On the page this folder you will find a brief summary of the environmental requirements met by this product. The complere environmental criteria document may be ordered from: TCO Development Unit S-11494 Stockholm Sweden Fax: +46 8 782 92 07 E-mail (Internet): development@tco.se Current information regarding TCO'95-approved and labelled products may also be obtained via the Internet, using the address: http://www.tco-info.
User’s Manual Information TCO'99-Ecological requirements for personal computers (TCO applied model only) Congratulations! You have just purchased a TCO'99 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products.
User’s Manual Information Current information regarding TCO'99 approved and labelled products may also be obtained via the Internet, using the address: http://www.tco-info.com/ Environmental requirements Flame retardants Flame retardants are present in printed circuit boards, cables, wires, casings and housings. Their purpose is to prevent, or at least to delay the spread of fire. Up to 30% of the plastic in a computer casing can consist of flame retardant substances.
User’s Manual 51 Information Authority Information in this document is subject to change without notice. © 2002 Samsung Electronics Co., Ltd. All rights reserved. Reproduction in any manner whatsoever without the written permission of Samsung Electronics Co., Ltd. is strictly forbidden. Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.
