SAMTRON 76E/76V/56B
User’s Manual Site Map Automatic Manual 2
User’s Manual Safety Instructions Warning / Caution Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment.
User’s Manual 4 Safety Instructions Power When not used for extended periods of time, set your PC to DPMS. If using a screen saver, set it to the active screen mode. If the size of your monitor is small, or if the same image is present for long periods of time, you may see afterimages due to damage to the flourescent substance on the inside of the CDT. ● Do not use a damaged or loose plug. ◆ This may cause an electric shock or fire.
User’s Manual Safety Instructions ● Disconnect the plug from the outlet during storms or lightening or if it is not used for a long period of time. ◆ Failure to do so may cause an electric shock or fire. ● Do not connect too many extension cords or plugs to an outlet. ◆ This may cause a fire.
User’s Manual 6 Safety Instructions Installation ● Do not cover the vents on the monitor cabinet. ◆ Bad ventilation may cause a breakdown or fire. ● Put your monitor in a location with low humidity and a minimum of dust. ◆ An electric short or fire could result inside the monitor. ● Do not drop the monitor when moving it. ◆ This may cause damage to the product or human body. ● Place the monitor on a flat and stable surface. ◆ The monitor can cause injury by falling. ● Set down the monitor carefully.
User’s Manual Safety Instructions Cleaning When cleaning the monitor case or the surface of the CRT, wipe with a slightly moistened, soft fabric. Do not clean Flat monitor with water. Use a water-diluted mild detergent. (Some detergents contain significant amounts of alcohol-based solvents, which can damage (color change) or crack the monitor case. The antiglare/anti-static surface coating on the CDT may also be affected.) Dilute the detergent (1:10 ratio) with water before using.
User’s Manual Safety Instructions Other ● Do not remove cover(or back). No user serviceable parts inside. ◆ This may cause an electric shock or a fire. ◆ Refer servicing to qualified service personnel. ● If your monitor does not operate normally - in particular,if there are any unusual sounds or smells coming from it - unplug it immediately and contact an authorized dealer or service. ◆ This may cause an electric shock or a fire. ● Do not place any heavy objects on the monitor.
User’s Manual ● Do not move the monitor right or left by pulling only the wire or the signal cable. ◆ This may cause a breakdown, electric shock or a fire due to damage to the cable. ● Never insert anything metallic into the monitor openings. ◆ This may cause an electric shock, fire or injury. ● Keep the monitor away from any magnetic substances.. ◆ This may cause discoloring or distortion of the image.
User’s Manual Introduction Unpacking ■ Monitor and Stand ■ Power Cord ■ Stand ■ Quick Setup Guide (Your monitor is shipped with the base detached.) Please make sure the following items are included with your monitor. If any items are missing, contact your dealer.
User’s Manual 11 Introduction Front 1. 2,3. 4. 5. 6. Note: Exit button Adjust buttons Menu button Power indicator Power button : Use this button to Exit the active menu or the OSD. : These buttons allow you to highlight and adjust items in the menu. : Use this button to open the OSD and activate a highlighted menu item. : Indicates normal or Power Saving Mode. : Use this button to turn the monitor on and off.
User’s Manual 12 Introduction Rear 1. Power port : Connect the power cord for your monitor to the power port on the back of the monitor. 2.Signal cable :Connect the end of the signal cable to your computer's video port (video board,video card or graphics card). Note: See Connecting Your Monitor for further information regarding cable connections. (The configuration at the back of the moniter may vary from product to product.) Bottom 1.
User’s Manual Setup Connecting Your Monitor 1.Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. 2.Connect the end of the signal cable to your computer's video port(video board, video card or graphics card). 3.If you are using a Macintosh computer, connect the cable to a Macintosh adapter, and set the pins on your adapter(Adapter not included). A PC-compatible computer does not need an adapter.
User’s Manual Setup Installing the Video Driver When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating sys tem to another. Follow the directions as appropriate for the operating system you have. Prepare a blank disk and download the driver program file at the Internet web site shown here. Internet web site : http://www.samtron.com/ Windows ME/98/95 1. Insert CD into the CD-ROM driver. 2.
User’s Manual Setup Installing the Video Driver Windows XP/2000 1. Insert CD into the CD-ROM driver. 2. Click "Windows XP/2000 Driver". 3. Choose your monitor model in the model list, then click the "OK" button. 4. Click the "Install" button in the "Warning" window. 5. If you can see following "Message" window, then click the "Continue Anyway" button. Then click "OK" button.
User’s Manual 16 Setup Installing the Video Driver This monitor driver is under certifying MS logo, and this installation don't damage your system. The certifide driver will be posted on Samtron Monitor Homepage. http://www.samtron.com/ 6. Monitor Driver installation is completed.
User’s Manual Setup Installing the Video Driver When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating sys tem to another. Follow the directions as appropriate for the operating system you have. Prepare a blank disk and download the driver program file at the Internet web site shown here. Internet web site : http://www.samtron.com/ Microsoft® Windows® XP Operating System 1.
User’s Manual Setup Installing the Video Driver 4. Click the "Properties" button on the "Monitor" tab and select "Driver" tab. 5. Click "Update Driver.." and select "Install from a list or.." then click "Next" button. 6. Select "Don't search ,I will.." then click "Next" and then click "Have disk".
User’s Manual Setup Installing the Video Driver 7. Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next" button. 8. If you can see following "Message" window, then click the "Continue Anyway" button. Then click "OK" button. This monitor driver is under certifying MS logo,and this installation don't damage your system.The certified driver will be posted on Samtron Monitor Homepage. . http://www.samtron.com/ 9.
User’s Manual 20 Setup Installing the Video Driver 10. Monitor driver installation is completed. Microsoft® Windows® 2000 Operating System When you can see "Digital Signature Not Found" on your monitor, follow these steps. 1. Choose "OK" button on the "Insert disk" window. 2. Click the "Browse" button on the "File Needed" window. 3. Choose A:(D:\Driver) then click the "Open" button and then click "OK" button. How to install 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Click "Start" , "Setting" , "Control Panel".
User’s Manual 21 Setup Installing the Video Driver Microsoft® Windows® Millennium Operating System 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Click "Start" , "Setting" , "Control Panel". Double click "Display" icon. Select the "Settings" tab and click "Advanced Properties" button. Select the "Monitor" tab. Click the "Change" button in the "Monitor Type" area. Choose "Specify the location of the driver". Choose "Display a list of all the driver in a specific location.." then click "Next" button.
User’s Manual 22 Setup Installing the Video Driver Version 4.00.950B 1. 2. 3. 4. 5. 6. 7. Click Start, Settings, Control Panel, and then double-click "Display" icon. In the "Display Properties" window, click the Settings tab and then click "Advanced Properties" button. In the "Advanced Display Properties" window, click the "Monitor" tab and then click "Change" button. In the "Select Device" window, click "Have Disk" button. Click "browse.." button and specify A:\(D:\driver) and click "OK".
User’s Manual Setup Tilt/Swivel Base Installation 1. Tilt/Swivel Base With the built-in pedestal, you can tilt and/or swivel the monitor for the most comfortable viewing angle. Note: The base is detachable. Your monitor is shipped with the base detached.
User’s Manual Setup 2. Attaching the Base If your monitor was supplied with the base detached, attach the base as follows. Remove the twist-tie before attaching the base to the monitor. 1. Place the monitor upside-down on a flat work surface. 2. Align the tabs on the base with the corresponding slots on the bottom of the monitor. Do not bend the snap. 3. Press the base onto the monitor until the tabs are fully engaged in the slots. 4.
User’s Manual Setup 3. Removing the Base 1. Turn off the monitor and unplug it from the electrical outlet. 2. Place the monitor upside down on a stable, flat work surface. 3. Squeeze and pull up on the release latch on the base. 4. Push the base toward the back of the monitor and lift up to remove the base.
User’s Manual On Screen Display (OSD) Menu System 1 Use this button to open the OSD and activate a highlighted menu item. 2.3 Use these buttons to highlight and adjust items using the On-Screen Display. These buttons are also direct access buttons for the contrast and brightness feature. 4 Use this button to Exit the active menu or the OSD.
User’s Manual On Screen Display (OSD) Menu System Menu How to adjust Brightness : Background brightness of screen. – Decreases brightness + Increases brightness Contrast : Contrast of screen image. – Decreases contrast + Increases contrast Horizontal Position : Horizontal screen position. – Moves screen left + Moves screen right Vertical Position : Vertical screen position. – Moves screen down + Moves screen up Horizontal Size : Horizontal screen size.
User’s Manual On Screen Display (OSD) Menu System Menu How to adjust Vertical Size : Vertical screen size. – Decreases size + Increases size Pincushion : Straightens screen vertical edges. – Curves image inward + Curves image outward Geometry : Adjust the Trapezoid, Parallelogram, Rotation, Pinbalance, V-Linearity of the screen image. Trapezoid : Width of top and bottom of screen.
User’s Manual On Screen Display (OSD) Menu System Menu How to adjust Rotation – Rotates entire screen left + Rotates entire screen right Pinbalance – Curves vertical lines to left + Curves vertical lines to right V-Linearity – Compresses image at top of screen + Compresses image at bottom of screen Language : – and + scroll through on-screen language options.
User’s Manual On Screen Display (OSD) Menu System Menu How to adjust Advanced H-Moire : Corrects for on-screen moiré pattern. – and + clear horizontal moiré V-Moire : Corrects for on-screen moiré pattern. – and + clear vertical moiré Video Input Level : Selects the video signal level. – Select 0.7 V + Select 1.
User’s Manual On Screen Display (OSD) Menu System Menu How to adjust Color Temperature – 9300k more blue + 6500k more red Zoom – Reduces view of display area + Enlarges view of display area Degauss : Removes color distortion caused by magnetic fields. Do not use more than once in 30 minutes. Recall : Returns monitor to original settings.
User’s Manual On Screen Display (OSD) Menu System Menu How to adjust Display Timing : Monitor display settings. – Factory timing + User timing OSD Lock/Unlock : Allows you to secure the current control settings so that they cannot be inadvertently changed. You can unlock the OSD controls at any time by using the same procedure. Push and hold in the Menu button for 10 seconds or more to Lock or to Unlock.
User’s Manual Troubleshooting Chek List Note : Before calling for service, check the information in this section to see if you can solve the problem yourself. If you do need assistance, please call the phone number on the warranty card, the phone number on the Information section or contact your dealer. Symptom No Images on the screen. I cannot trun on the monitor. Chek List Solution Is the power cord connected properly? Check the power cord connection and supply.
User’s Manual Troubleshooting Symptom The image on the screen is shaking. Chek List Solution Check the monitor configuration to see if it is in Interlace Mode. (Interlace Mode: Vertical frequency 43Hz, 87Hz(i), etc) The signal from the video card exceeds the maximum resolution and frequency of the monitor. Are there any magnetic products such as a high voltage wire near by? Move the monitor away from anything that can create a strong magnetic field.
User’s Manual Troubleshooting Symptom The screen is partialy distorted. LED is blinking but no images on the screen. Chek List Are there any magnetic products such as an adapter, speaker or a high voltage wire near the monitor? Is the frequency properly adjusted when checking the Display Timing on the menu? Solution Enter the OSD and perform a 'Degauss'. Keep the monitor away from any magnetic products. Adjust the frequency properly by referring to the video card manual and the Preset Display Modes.
User’s Manual Troubleshooting Check the following items if there is trouble with the monitor. 1. Check if the power cord and the cable are properly connected to the computer. 2. Check if the computer beeps more than 3 times when booting. (If it does, request an after-service for the main board of the computer.) 3. If you installed a new video card or if you assembled the PC, check if the installed the adapter (video) driver and the monitor driver. 4.
User’s Manual 37 Troubleshooting Q&A Question How can I change the frequency? Answer Frequency can be changed by reconfiguring the video card. Note that video card support can vary, depending on the version of the driver used. (Refer to the computer or the video card manual fordetails.) How can I adjust the resolution? Windows 95/98: Set the resolution at the Control Panel, Display, Settings. Windows 3.1: Change the resolution and the colors using the VGA Utility provided by the video card.
User’s Manual Troubleshooting Self-Test Feature Check A self-test feature is provided that allows you to check for proper monitor function. If your monitor and computer are properly connected but the monitor screen remains dark and the power indicator is blinking, run the monitor self-test by performing the following steps: Self-Test Feature Check 1. Turn off both your computer and the monitor. 2. Unplug the video cable from the back of the computer. 3. Turn on the monitor.
User’s Manual 39 Troubleshooting Self-Test Feature Check Warning Messages If there is something wrong with the input signal, a message appears on the screen or the screen goes blank although the power indicator LED is still on. The message may indicate that the monitor is out of scan range or that you need to check the signal cable. Environment The location and the position of the monitor may influence the quality and other features of the monitor. 1.
User’s Manual Specifications General Specifications General Model Name SAMTRON 76E Picture Tube Type 17" (43cm) Full square type (40.6cm viewable) Deflection angle 90° Dot Pitch 0.23 mm(Horizontal) Screen type Silica coated with anti-electronic properties (TCO : Multilayer coating) Medium-short persistence phosphor. Maximum Resolution 1280 Dots, 1024 Lines Active Display Horizontal 12.3 ± 0.16 inch (312 ± 4 mm) Vertical 9.2 ± 0.
User s Manual Specifications General Specifications General Model Name SAMTRON 76V Picture Tube Type 17" (43cm) Full square type (40.6cm viewable) Deflection angle 90° Dot Pitch 0.23 mm(Horizontal) Screen type Medium-short persistence phosphor. Maximum Resolution 1280 Dots, 1024 Lines Active Display Horizontal 12.3 ± 0.16 inch (312 ± 4 mm) Vertical 9.2 ± 0.16 inch (234 ± 4 mm) Synchronization Horizontal 30 ~ 70 kHz Vertical 50 ~ 160 Hz Input Signal, Terminated Analog 0.
User’s Manual Specifications General Specifications General Model Name SAMTRON 56B Picture Tube Type 15" (38cm) Full square type (35cm viewable) Deflection angle 90° Dot Pitch 0.24 mm(Horizontal) Screen type Medium-short persistence phosphor. Maximum Resolution 1280 Dots, 1024 Lines Active Display Horizontal 10.5 ± 0.16 inch (267 ± 4 mm) Vertical 7.9 ± 0.16 inch (200 ± 4 mm) Synchronization Horizontal 30 ~ 70 kHz Vertical 50 ~ 160 Hz Input Signal, Terminated Analog 0.
User’s Manual 43 Specifications Preset Display Modes If the signal transferred from the computer is the same as the following Preset Display Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows. Display Mode Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) IBM, 640 x 480 31.469 59.940 25.
User’s Manual 44 Specifications PowerSaver This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor into a low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you move the computer's mouse or press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods.
User’s Manual Information Service ● SAMTRON SEOUL 15TH FL, JOONGANG DAILY NEWS BLDG. 7, SOONHWA-DONG,CHUNG-KU, SEOUL, KOREA, 100-759 TEL : (82-2) 727-3114 ● SAMTRON U.S.A SAMTRON COMPUTER PRODUCTS CUSTOMER SERVICE 400 Valley Road Suite 201, Mt. Arlington, NJ 07856 TEL : 973-601-6200, FAX : 973-601-6001 1-800-SAMTRON (1-800-726-8766) ● SAMTRON CANADA SAMSUNG ELECTRONICS CANADA INC.
User’s Manual Information Terms ● Dot Pitch The image on a monitor is composed of red, green and blue dots. The closer the dots, the higher the resolution. The distance between two dots of the same color is called the 'Dot Pitch'. Unit: mm ● Vertical Frequency The screen must be redrawn several times per second in order to create and display an image for the user. The frequency of this repetition per second is called Vertical Frequency or Refresh Rate.
User’s Manual 47 Information Regulatory FCC Information | IC Compliance Notice | MPR II Compliance | European Notice (Europe only) | PCT Notice | TCO'95-Ecological requirements for personal computers (TCO applied model only) | TCO'99-Ecological requirements for personal computers (TCO applied model only) ● FCC Information User Instructions The Federal Communications Commission Radio Frequency Interference Statement includes the following warning: Note: This equipment has been tested and found to comply w
User’s Manual 48 Information Provided with this monitor is a detachable power supply cord with IEC320 style terminations. It may be suitable for connection to any UL Listed personal computer with similar configuration. Before making the connection, make sure the voltage rating of the computer convenience outlet is the same as the monitor and that the ampere rating of the computer convenience outlet is equal to or exceeds the monitor voltage rating.
User’s Manual 49 Information ● TCO'95-Ecological requirements for personal computers (TCO applied model only) AB general requirements AB2 Written Eco-document acompanying the products Congratulations! You have just purchased a TCO'95 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and to the further development of environmentally- adapted electronic products.
User’s Manual 50 Information Environmental Requirements Brominated flame retardants are present in printed circuit boards, cables, wires, casings and housings. In turn, they delay the spread of fire. Up to thirty percent of the plastic in a computer casing can consist of flame retardant substances.
User’s Manual 51 Information The requirements cover a wide range of issuse: environment, ergonomics, usability, reduction of electric and magnetic fields, energy consumption and electrical safet Why do we have environmentally labelled computers? In many countries, environmental labelling has become an established method for encouraging the adaptation of goods and services to the environment.
User’s Manual 52 Information CFCs (freons) The relevant TCO'99 requirement states that neither CFCs nor HCFCs may be used during the manufacture and assembly of the product. CFCs (freons) are sometimes used for washing printed circuit boards. CFCs break down ozone and thereby damage the ozone layer in the stratosphere, causing increased reception on earth of ultraviolet light with e.g. increased risks of skin cancer (malignant melanoma) as a consequence.
User’s Manual 53 Information Authority Information in this document is subject to change without notice. © 2001 Samsung Electronics Co., Ltd. All rights reserved. Reproduction in any manner whatsoever without the written permission of Samsung Electronics Co., Ltd. is strictly forbidden. Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.
http://www.samtron.
