Install Drivers Install Programs
Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment. Prohibited Important to read and understand at all times Do not disassemble Disconnect the plug from the outlet Do not touch Grounding to prevent an electric shock Power When not used for extended period of time, set your computer to DPMS. If using a screen saver, set it to the active screen mode. Do not use a damaged or loose plug. z This may cause an electric shock or fire.
Do not pull the plug out by the wire nor touch the plug with wet hands. z This may cause an electric shock or fire. Use only a properly grounded plug and receptacle. z An improper ground may cause electric shock or equipment damage. Do not excessively bend the plug and wire nor place heavy objects upon them, which could cause damage. z This may cause an electric shock or fire. Do not connect too many extension cords or plugs to an outlet. z This may cause fire.
Set down the monitor carefully. z The monitor could be damaged or broken. Do not place the monitor face down. z The TFT-LCD surface may be damaged. Installing a wall bracket must be done by a qualified professional. z z Installation by unqualified personnel may result in injury. Always use the mounting device specified in the owner's manual. Leave a space for ventilation between the product and the wall. z Poor ventilation may cause the interior temperature to rise and lead to fire.
Use the recommended detergent with a smooth cloth. If the connector between the plug and the pin is dusty or dirty, clean it properly with a dry cloth. z A dirty connector may cause an electric shock or fire. Contact a Service Center or Customer Center for interior cleaning once a year. z Keep the product's interior clean. Dust which has accumulated in the interior over an extended period of time may cause malfunction or fire. Others Do not remove cover (or back). No user serviceable parts inside.
Do not try to move the monitor by pulling only the wire or the signal cable. z This may cause a breakdown, electric shock or fire due to damage to the cable. Do not move the monitor right or left by pulling only the wire or the signal cable. z This may cause a breakdown, electric shock or fire due to damage to the cable. Do not cover the vents on the monitor cabinet. z Bad ventilation may cause a breakdown or fire. Do not place water containers, chemical products or small metal objects on the monitor.
Keep the volume at a proper level when you use the headphones. z Excessively loud volume levels may damage hearing. Keep a proper distance between your eyes and the monitor screen. z Sitting too close to the monitor on a continuous basis may damage eyesight. To ease eye strain, take at least a five-minute break after every hour of using the monitor. Do not use the monitor where it may be exposed to strong vibrations.
contact a service center.
Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Contact a local dealer to buy optional items.
D-Sub Cable Power Cord Radio Antenna Audio Cable Audio Cable Option B USB Cable D-Sub Cable DVI Cable Power Cord Audio Cable USB Cable DVI Cable Remote Control Batteries (AAA X 2) Connecter Batteries (AAA X 2) Connecter Cable(Option B) Sold separately Radio Antenna Others Sold separately Others Option B WISELINK Front Remote Control 1. MENU 2. CH 3. + VOL - Front 4. ENTER/FM RADIO 5. SOURCE 1.
6. PIP 2. CH 7. Power 3. - VOL +button 8. Power indicator 4. ENTER/FM RADIO 5. SOURCEControl Sensor 9. Remote 6. PIP 7. Power button 8. Power indicator 9. Remote Control Sensor 1. MENU Use this button for open the on-screen menu and exits from the menu screen or closes screen adjustment menu. 2. CH Moves from one menu item to another vertically or adjusts selected menu values. In TV mode, selects TV channels. >>Click here to see an animation clip 3.
Rear (The configuration at the back of the monitor may vary from product to product.) 1. Power DC Power Connection Terminal Connection Terminal This product may be used with 90 ~ 264VAC. 2. PC connection terminal z z z Computer connection terminal (DVI(HDCP)) Computer connection terminal(15 Pin D-SUB) Audio connection terminal 3.
- Scart is mainly used in Europe. 5. AV connection terminalterminal EXT(RGB) connection EXT(RGB) connection terminal z S-Video connection terminal (Input) - Scart is mainly used in Europe. z Video connection terminal (Input) z Left(L) / Right(R) audio connection terminal (Input) z Left(L) / Right(R) AUDIO connection terminal (Input) 6. AV connection terminal See Connecting the Monitor for further information cable connections.
17. P.SIZE 5. MUTE 18. STILL 6. TTX/MIX 7. PIP MENU 19. 20. 8. S.MODE ENTER 21. 9. DUAL/MTS FM RADIO 22. PRE-CH 10. CH/P 23. SOURCE 11. 24. SIZE 12. INFO 25. POSITION 13. EXIT 14. Up-Down Left-Right Buttons 26. MAGIC-CH 15. AUTO 1. POWER Use this button to turn the monitor on and off. 16. P.MODE, M/B (MagicBright™) 17. P.SIZE 2. CHANNEL 18. STILL Selects TV channels in the TV mode. You may use19. this PIP button in PIP mode as well. 20. S.MODE 3. +100 Press to select channels over 100. 21.
11. SOURCE 16. P.MODE, M/B (MagicBright™) When youfrom press button, current mode is displayed on the lower center of the screen. Switches PCthis mode to Video mode. Changing the source is allowed only external devices that are connected to the monitor at the /time. TV AV / Ext. / S-Video /Component Mode : P.MODE( Picture Mode ) The Monitor has four automatic picture settings that are preset at the factory. 12. Then INFO push button again to circle through available preconfigured modes.
Connecting the monitor 1. Connecting to a Computer 1. Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. 2-1. Using the D-sub (Analog) connector on the video card. Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor. 2-2. Using the DVI (Digital) connector on the video card. Connect the DVI Cable to the DVI Port on the back of your Monitor. 3.
If you properly yourismonitor using the Press DVI connector but gettoahave blankthe or monitor fuzzy screen, check to seeconnect if the monitor status set to analogue. Source button doubleto see the if the monitor status is set to analogue. Press Source button to have the monitor doublecheck input signal source. check the input signal source. 2. Connecting to a Macintosh 2. Connecting to a Macintosh 1. Connect the power cord to the DC adapter and then connect the adapter jack to the DC POWER 1.
1. Input devices such as DVDs, VCRs or Camcorders are connected to the Video or S-Video terminal of the monitor using the RCA or S-Video cable. S-Video, RCA cable and EXT(RGB) cable is optional. 2. Then, start the DVD, VCR or Camcorders with a DVD disc or tape inserted. 3. Select AV or S-Video using the SOURCE button on the monitor's front. 4. Connect the Audio (R) and Audio (L) terminals of a DVD, VCR or Camcorders to the monitor's R and L audio input terminals using audio cables. 1-2.
1. Connect the CATV or antenna coaxial cable to the Antenna terminal on the rear of the monitor. You need to use a coaxial antenna cable. When using an interior antenna terminal: Check the antenna terminal on the wall first and connect the antenna cable. When using an outdoor antenna: If you are using an outdoor antenna, use a professional for installation if possible. To connect the RF cable to the antenna input terminal: Keep the copper wire portion of the RF cable straight. 2. Turn on the monitor. 3.
3. Select Component using the SOURCE button on the monitor's front. 4. Connecting Headphone You may connect your Headphone to the monitor. 1. Connect your Headphone to the Headphone connection terminal. Using the Stand This monitor supports various types of VESA-standard bases. You need to either fold or remove the base in use in order to install a VESA base. 1. Folding the base The monitor may be reclined from -5 to 15 degrees. 2.
A. Monitor B. Mounting interface pad 1. 2. 3. 4. Turn off your monitor and unplug its power cord. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen. Remove four screws and then remove the Stand from the LCD monitor. Align the Mounting Interface Pad with the holes in the Rear Cover Mounting Pad and secure it with four screws that came with the arm-type base, wall mount hanger or other base.
4. Click the "Install" button in the "Warning" window. 5. Monitor driver installation is completed. Windows XP/2000 1. Insert CD into the CD-ROM drive. 2. Click "Windows XP/2000 Driver" 3. Choose your monitor model in the model list, then click the "OK" button. 4. If you can see following message window, then click the "Continue Anyway" button. Then click "OK" button. This monitor driver is under certified MS logo,and this installation doesn't damage your system.
Windows XP | Windows 2000 |Windows Me |Windows NT | Linux When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions appropriate for the operating system you have. Prepare a blank disk and download the driver program file at the Internet web site shown here. z Internet web site : http://www.samsung-monitor.com/ (Worldwide) http://www.samsungusa.
6. Select "Don't search ,I will.." then click "Next" and then click "Have disk". 7. Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next" button. 8. If you can see following message window, then click the "Continue Anyway" button. Then click "OK" button. This monitor driver is under certified MS logo,and this installation doesn't damage your system.The certified driver will be posted on Samsung Monitor homepage. http://www.
10. Monitor driver installation is completed. Microsoft® Windows® 2000 Operating System When you can see "Digital Signature Not Found" on your monitor, follow these steps. 1. Choose "OK" button on the "Insert disk" window. 2. Click the "Browse" button on the "File Needed" window. 3. Choose A:(D:\Driver) then click the "Open" button and then click "OK" button. How to install 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Click "Start" , "Setting" , "Control Panel". Double click the "Display" Icon.
Microsoft® Windows® NT Operating System 1. Click Start, Settings, Control Panel, and then double-click Display icon. 2. In Display Registration Information window, click Settings Tab and then click All Display Modes. 3. Select a mode that you wish to use (Resolution, Number of colors and Vertical frequency) and then click OK. 4. Click Apply button if you see the screen working normally after clicking Test.
How to delete the Natural Color software program Select "Setting" / 'Control Panel" on the "Start" menu and then double-click "Add/Delete a program". Select Natural Color from the list and then click the [Add/Delete] button.
Input Available Mode : PC / DVI : TV : AV : S-Video OSD Description Source List Use to select PC, TV or other external input source connected to the Monitor. Use to select the screen of your choice. • PC • DVI : HDCP supported • TV • Ext.- EXT(RGB) is mainly used in Europe. • AV • S-Video • Component PIP When external A/V devices such as VCRs or DVDs are connected to the monitor, PIP allows you to watch video from those devices in a small window super-imposed on the PC Video signal.
1) PIP • ON/ Off : Turn the PIP Screen on or off. 2) Source • PC / DVI : TV / Ext.(EXT(RGB) is mainly used in Europe.) / AV / SVideo / Component Mode : Select the input source for the PIP. 3) Size : Change the Size of the PIP window. If you select , in Size, Position and Transparency will not be activated. 1) PIP 2) Source 3) Size 4) Position 5) Transparency 4) Position : Change the Position of the PIP window. 5) Transparency • High / Medium / Low / Opaque : Adjust the Transparency of PIP windows.
MagicBright™ MagicBright™ is a new feature providing the optimum viewing environment depending on the contents of the image you are watching. Currently four different modes are available: Entertain, Internet,Text and Custom. Each mode has its own pre-configured brightness value. You can easily select one of four settings by simply pressing the MagicBright™ control button. 1) Entertain : High Brightness For watching motion pictures such as a DVD or VCD.
: Adjusts the Brightness of the PIP window on the screen. 3) Sharpness : Adjusts the difference between the lightest and darkest areas of the PIP window. 4) Color : Adjusts the Color of the PIP window on the screen. 5) Tint : Adds a natural tone to the PIP window. Available : PIP ON TV / Ext.
• Normal • Zoom 1 • Zoom 2 - ZOOM1, ZOOM2 are not available in 1080i(or over 720p) of DTV. Digital NR - Digital Noise Reduction. You can turn the Noise Elimination feature On/Off. The Digital Noise Elimination feature allows you to enjoy clearer and crisper images. • On /Off Film Mode You can turn Film Mode On/Off. The Film Mode feature offers you a theater-quality viewing experience.
Custom The sound settings can be adjusted to suit your personal preference. 1) Bass : Emphasize low frequency audio. 2) Treble : Emphasize high frequency audio. 3) Balance : Allows you to adjust the sound balance between the left and right speakers. Auto Volume Reduces the differences in volume level among broadcasters. • On /Off Dolby Virtual Dolby Virtual Sound On/Off (Dolby Virtual simulates the effect of the Dolby Surround sound system, recreating the movietheatre or concert-hall- quality sound.
Available Mode : PC / DVI : TV : AV : S-Video : Component OSD Description Air/CATV The channel system can be set in several different ways. • Air • STD • HRC • IRC • AFN STD, HRC, IRC, AFN, and Air identify various types of cable TV systems. Contact your local cable company to identify the type of cable system that exists in your particular area. Auto Program The TV automatically cycles through all of the available channels and stores them in memory. This takes about one to two minutes.
Available Mode OSD : PC / DVI : TV : AV : S-Video : Component Description Play When you turn the power on of the product for the first time since it released Area Configuration from a factory, menu to select location will appear. Choose the region and country where you use the monitor. This is because broadcasting type varies according to region and country. You can select broadcasting type in OSD menu as well by selecting MENUSetup-Area Configuration.
appearance of closed caption text. 1) Caption : Off / On 2) Mode : Caption / Text 3) Channel : 1 / 2 4) Field : 1 / 2 Changes the opaqueness of the background of the OSD. Menu Transparency • High • Medium • Low • Opaque Blue Screen If no signal is being received or the signal is very weak, a blue screen automatically replaces the noisy picture background. If you wish to continue viewing the poor picture, you must set the "Blue screen" mode to "Off".
Overview Setup OSD Mode Troubleshooting Using WISELINK WISELINK is used to play Photo Files (*.jpg), Music Files (*.mp3, *.wav) and Movie Files (*.avi, *.mov) stored in the memory card on the Monitor. What is a Memory Card? A memory card is an auxiliary storage device used in AV equipment to exchange data between devices. It is mainly used in digital cameras, digital camcorders,MP3 players, notebooks, and PDAs.
Cautions on using WISELINK Mode - Do not insert foreign objects into the slot. Insert the memory card in the proper direction Do not remove the memory card when it is in use. The manufacturer's responsibility does not include damaged data. (Be careful not to corrupt data and be sure to back up files.) - Use the slot cover so that dust and foreign objects cannot enter the slot when WISELINK is not in use.
Overview Setup OSD Mode Troubleshooting Connecting WISELINK Connecting USB port If the computer is connected to WISELINK by a cable, such works as writing and reading data are possible at the computer source. z z Connect the upstream USB port to an appropriate USB port on your computer. Connect USB peripherals to the downstream USB ports on the WISELINK.
Overview Setup OSD Mode Troubleshooting Switching to WISELINK Mode 1 Switching to WISELINK Mode 2 While making a selection, information about the selected file is displayed on the right side of the screen. z When no card is inserted, "Please Insert Card" will be displayed. z When a new card is inserted or the inserted card is loose, the memory card selecting screen will automatically open.
When any card other than the memory card currently in use becomes loose, "Please Insert Card" will be displayed on the center of the screen. z A maximum of one thousand files can be displayed. z File names are displayed in English only. z Images edited by JPEG editors (for example: Photoshop or Paintshop) may not appear normal. z When the monitor is set to PAL type, pressing channel button will switch its' mode to TV mode automatically. Photo Playback JPEG file format is supported. 1.
rotated image will be just shown at the photo full screen. You can rotate the image zoomed. Zoom You can zoom the image 3 times. You can use the picture. You can zoom the image rotated. Close Menu close. buttons to move the enlarged Music File Playback MP3/WAV file format is supported. 1. Press the or button to move to a 4. Press the INFO button to move to the WISELINK setup. desired file and it will automatically play. 2. The active page is displayed. Change the pages by pressing or button. 5.
Movie File Playback AVI/MOV file format is supported. 1. Press the or button to move to a 4. Press the INFO button to move to the WISELINK setup. desired file and it will automatically play. 2. The active page is displayed. Change the pages by pressing or button. 5. The title, total playback time, creation date and number (current file number / total file number) for the selected file will be displayed. 3. Press the EXIT button to move to the previous menu. 6. The selected memory card type is displayed.
1. JPEG/MP3/WAV/AVI/MOV files. 2. The active page is displayed. Change the pages by pressing or 4. Press the INFO button to move to the WISELINK setup. 5. The information for the current file is displayed. button. 3. Press the EXIT button to ruturn to the previous menu. i ALL FILE j k l m n WISELINK Setup You can set various functions in WISELINK mode. 6. The selected memory card type is displayed.
z z z z Turning off the Monitor set or switching to another mode during setup will cancel your settings. The Music Slide Show always repeats all the music. It doesn't follow the setting of Music Repeat. The ENTER button will stop the Music Slide Show and Bar setup menu is displayed. The INFO button will stop the Music Slide Show and setup menu is displayed.
Screen Saver A screen saver is provided to prolog the life of the Screen. z Off: Stops the screen saver. z 5min: The screen saver automatically turns on if no button is pressed within five minutes. z 10min: The screen saver automatically turns on if no button is pressed within ten minutes.
Overview Setup OSD Mode Troubleshooting If the Monitor seems to have a problem, first try this list of possible problems and solutions. If none of these troubleshooting tips apply, then call your nearest service center. Problem Image or Music Files do not play back. Each picture or slide has a different running time. The memory card is not recognized. The volume changes while music is played. There is a blank screen when switching to WISELINK.
install the driver from the CD, so that the computer recognizes the driver. Note that it will not recognize WISELINK. The file names are distorted. WISELINK only supports file names in English. It does not support file names in other languages (Chinese, Japanese, etc.).
Self-Test Feature Check Check the following items yourself before calling for service. Contact the service center for problems that you cannot solve by yourself. Self-Test Feature Check | Not Supported Mode | Not Optimum Mode | Display Adapter Driver Maintenance and Cleaning | Symptoms & Recommended Actions 1. Self-Test Feature Check Your monitor provides a self test feature that allows you to check whether your monitor is functioning properly. 1. Turn off both your computer and the monitor. 2.
Contact the computer dealer or manufacturer for information on Safe Mode Booting. Refer to Specifications > Preset Timing Modes for the resolutions or frequencies that are supported by the monitor. Sometimes the screen turns black without the "Not Supported Mode" message appearing on the screen. This indicates the monitor is set for a frequency out of range or the PowerSaver mode is on. Contact the computer dealer or manufacturer for information on Safe Mode Booting. 3.
2. Maintaining the Flat Panel Display Screen. 6. Symptoms and Recommended Actions Clean with arecreates soft clothvisual (cotton flannel) smoothly. A monitor signals received from the computer. Therefore, if there is trouble with the computer or the video card, this can cause the monitor to become blank, have poor coloring, noise, Video mode not supported, etc. In this case, first check the source of the problem, and then contact z Never use acetone, benzene or thinner. a service center or your dealer.
Picture rolls vertically. z "Check Signal Cable" message z Image is not clear. Picture is blurred. z "Not Supported Mode" message z z Picture image is unstable and vibrates. z Ghost are shown in the Pictureimages rolls vertically. picture. z The image is too light or too dark Image is not clear. Picture is blurred. z Screen color is inconsistent. z z Color image is distorted with Picture image is unstable and dark shadows. vibrates. z z z z White color is poor.
Check if the power is on. Check if the power cord is securely connected. z Check if a special fluorescent or neon lamp is on in the Problems related to the remote control and their solutions are listed. vicinity. z 4. Problems related to Remote Control z Problems Q& A The remote control buttons do not respond.
General General Model Name SyncMaster 730MP LCD Panel Size 17" Diagonal Display area 337.920(H) x 270.336(V) Pixel Pitch 0.264(H) x 0.264(V) Type a-si TFT active matrix Synchronization Horizontal 31 ~ 81kHz Vertical 56 ~ 85Hz Display Color 16,194,277 Colors Resolution Maximum resolution SXGA 1280 x 1024 @75Hz Input Signal, Terminated RGB Analog , DVI Compliant Digital RGB. Composite H/V Sync, 0.
Power Consumption Less than 55W Power Saving Less than 2W Dimensions (WxDxH)/ Weight 496 x 62.6 x 336 mm (Without stand) 496 x 170 x 378 mm / 5.7 kg (With Stand) VESA Mounting Interface 75mm x 75mm (for use with Specialty(Arm) Mounting hardware.
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows. Table 1. Preset Timing Modes Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) MAC, 640 x 480 35.000 66.667 30.240 -/- MAC, 832 x 624 49.726 74.551 57.
Countries Germany Norway Spain Israel Denmark Portugal Netherlands Austria Singapore Indonesia Australia China North Korea Rumania Ireland England South Africa Hongkong Argentina Uruguay Paraguay Brazil SECAM Broadcasting Systems SECAM-B Countries SECAM-D Iran Iraq Saudi arabia Syria Lebanon Egypt SECAM-K1 Russia Hungary Bulgaria Poland SECAM-L France Horizontal Frequency The time to scan one line connecting the right edge to the left edge of the screen horizontally is called Horizontal Cycle
Service AUSTRALIA : Samsung Electronics Australia Pty Ltd. Customer Response Centre 7 Parkview Drive, Homebush Bay NSW 2127 Tel : 1300 362 603 http://www.samsung.com.au/ BRAZIL : Samsung Eletronica da Amazonia Ltda. R. Prof. Manoelito de Ornellas, 303, Terro B Chacara Sto. Antonio, CEP : 04719-040 Sao Paulo, SP SAC : 0800 124 421 http://www.samsung.com.br/ CANADA : Samsung Electronics Canada Inc.
http://samsung.es/ FRANCE : SAMSUNG ELECTRONICS FRANCE Service Paris Nord 2 66 rue des Vanesses BP 50116 Villepinte 95950 Roissy CDG Cedex Tel : 08 25 08 65 65 Fax : 01 48 63 06 38 http://www.samsungservices.com/ GERMANY : TELEPLAN Rhein-Main GmbH Feldstr. 16 64331 Weiterstadt T. 06151/957-1306 F. 06151/957-1732 * EURO 0.12/Min http://www.samsung.de/ HUNGARY : Samsung Electronics Magyar Rt. 1039, Budapest, Lehel u. 15-17. Tel: 36 1 453 1100 Fax: 36 1 453 1101 http://www.samsung.
Fax: 51-1-336-8551 http://www.samsungperu.com/ PORTUGAL : SAMSUNG ELECTRONICA PORTUGUESA S.A. Rua Mário Dioniso, No2 - 1º Drt. 2795-140 LINDA-A-VELHA Tel. 214 148 114/100 Fax. 214 148 133/128 Free Line 800 220 120 http://www.samsung.pt/ SOUTH AFRICA : Samsung Electronics,5 Libertas Road, Somerset Office Park, Bryanston Ext 16. Po Box 70006, Bryanston,2021, South Africa Tel : 0027-11-549-1621 Fax : 0027-11-549-1629 http://www.samsung.co.
Terms Sync Signal Sync (Synchronized) Signals refer to the standard signals that are required to display desired colors on the monitor. They are divided into Vertical and Horizontal Sync Signals. These signals display normal color images by the set resolution and frequency. Types of Sync Signals Separate This is a scheme of transmitting individual vertical sync signals to the monitor. Composite This is a scheme of combining vertical sync signals into one composite signal and transmitting it to the monitor.
Broadcasting service provided via satellite. Enables high picture quality and clear sound throughout the country regardless of the location of the viewer. Sound Balance Balances the levels of the sound coming from each speaker in televisions with two speakers. Cable TV Whereas the terrestrial broadcasting is delivered via frequency signals through the air, cable broadcasting is transmitted via a cable network. In order to view cable TV, one must purchase a cable receiver and hook it up to the cable network.
Authority Information in this document is subject to change without notice. © 2004 Samsung Electronics Co., Ltd. All rights reserved. Reproduction in any manner whatsoever without the written permission of Samsung Electronics Co., Ltd. is strictly forbidden. Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.
FCC Information | IC Compliance Notice | MPR II Compliance European Notice (Europe only) | PCT Notice | VCCI | TCO'95-Ecological requirements for personal computers (TCO'95 applied model only) TCO'99-Ecological requirements for personal computers (TCO'99 applied model only) TCO'03-Ecological requirements for personal computers (TCO'03 applied model only) TCO'03 Recycling Information (TCO'03 applied model only) Medical Requirement Mercury Statement (LCD Monitor, LCD TV, DLP Projection TV, Projector for USA o
MPR II Compliance This monitor complies with SWEDAC(MPR II) recommendations for reduced electric and magnetic fields. European Notice(Europe Only) Products with the CE marking comply with the EMC Directive(89/336/EEC), (92/31/EEC), (93/68/EEC) and the Low Voltage Directive (73/23/EEC) issued by the Commission of the European Community.
There are also other characteristics of a monitor, such as energy consumption levels, that are important from both the working and natural environment viewpoints. Since all types of conventional electricity generation have a negative effect on the environment (acidic and climate-influencing emissions, radioactive waste, etc.) it is vital to conserve energy. Electronic equipment in offices consumes an enormous amount of energy, since it is often routinely left running continuously.
electronics components concerned with the display unit. CFCs (freons) CFCs (freons) are sometimes used for washing printed circuit boards and in the manufacturing of expanded foam for packaging. CFCs break down ozone and thereby damage the ozone layer in the stratosphere, causing increased reception on Earth of ultraviolet light with consequent increased risks of skin cancer (malignant melanoma).
via the Internet, using the address: http://www.tco-info.com/ Environmental requirements Flame retardants Flame retardants are present in printed circuit boards, cables, wires, casings and housings. Their purpose is to prevent, or at least to delay the spread of fire. Up to 30% of the plastic in a computer casing can consist of flame retardant substances. Most flame retardants contain bromine or chloride, and those flame retardants are chemically related to another group of environmental toxins, PCBs.
Energy z Energy-saving mode after a certain time ?beneficial both for the user and the environment z Electrical safety Emissions z z Electromagnetic fields Noise emissions Ecology The product must be prepared for recycling and the manufacturer must have a certified environmental management system such as EMAS or ISO 14 000 z Restrictions on o chlorinated and brominated flame retardants and polymers o heavy metals such as cadmium, mercury and lead.
This equipment has been tested and found to comply with the limits for medical devices to the IEC 601-1-2:1994. These limits are designed to provide reasonable protection against harmful interference in a typical medical installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to other devices in the vicinity.
PRODUCT INFORMATION (Image Retention Free) LCD Monitors and TVs may have image retention when switching from one image to another especially after displaying a stationary image for a long time. This guide is to demonstrate correct usage of LCD products in order to protect them from Image retention. What is Image retention ? During normal operation of a LCD panel, pixel image retention doesn't occur.
The best way to protect your monitor from Image retention is to set your PC or System to operate a Screen Saver program when you are not using it. Image retention may not occur when a LCD panel is operated under normal conditions. Normal conditions are defined as continuously changing video patterns. When the LCD panel is operated for a long time with a fixed pattern (-over 12 hours-), there may be slight difference in voltage between electrodes that work the liquid crystal (LC) in a pixel.
