SyncMaster 700DRN LCD Display User Manual The color and the appearance may differ depending on the product, and the specifications are subject to change without prior notice to improve the performance.
Safety Instructions Notational Note These safety instructions must be followed to ensure your safety and prevent property damage. Make sure to read the instructions carefully and use the product in the correct manner. Warning / Caution Failure to follow directions noted by this symbol could result in bodily harm or damage to the equipment.
Safety Instructions Do not forcefully bend or pull the power plug and do not place any heavy material on it. • Otherwise, this may result in fire. Do not connect multiple appliances to the same power outlet. • Otherwise, this may cause fire due to overheating. Do not disconnect the power cord while using the product. • Otherwise, this may result in damage to the product due to electric shock.
Safety Instructions When putting the product down, make sure to put it down softly. • Otherwise, this may result in damage to the screen display. Do not place the front of the product on the floor. • Otherwise, this may result in damage to the screen display. Install your product in a well ventilated location. Ensure that there is a clearance of more than 10 cm from the wall. • Otherwise, it may result in fire due to an increase in the internal temperature.
Safety Instructions Others The product is a high voltage product. Ensure that users do not disassemble, repair or modify the product themselves. • Otherwise, this may result in electric shock or fire. If the product needs to be repaired, contact a Service Center. If there is a strange smell or a strange sound or smoke is coming from the product, disconnect the power plug immediately and contact a Service Center. • Otherwise, this may result in electric shock or fire.
Safety Instructions Set a resolution and frequency appropriate to the product. • Otherwise, your eyesight may be damaged. When using headphones or earphones, do not turn the volume too high. • Having the sound too loud may damage your hearing. If you continually move closer to the product screen, your eyesight may be failing. Take a rest for at least five (5) minutes after using the monitor for one (1) hour. This reduces the weariness of your eyes.
Safety Instructions When replacing the battery, insert it with right polarity (+, -). • Otherwise, the battery may become damaged or it may cause fire, personal injury or damage due to leakage of the internal liquid. Use only the specified standardized batteries, and do not use a new battery and a used battery at the same time. • Otherwise, the batteries may be damaged or cause fire, personal injury or damage due to a leakage of the internal liquid.
Safety Instructions Refer to the Cable Safety Specifications. • UL specifications - Use a cable with 14 AWG or more • KS specification - Use a cable with 20.SQ or more • IEC specification - Use a cable with 2.
Introduction Package Contents Note • This product can be used after it is completely assembled by a system integrator (SI). • Issues regarding the exterior and interior design and EMC compliance requirements for this product are the responsibility of the system integrator (SI). Samsung Electronics shall not be liable for these issues. • Should you need any information on the product design, please call a Samsung Service Center.
Introduction Manuals Quick Setup Guide Warranty Card User's Guide (Not available in all locations) MagicInfo Software CD, MagicInfo Manual CD Others Remote Control Batteries (AAA X 2) (Not available in all locations) Sold separately DVI Cable LAN Cable TV Tuner 9 D-Sub Cable
Introduction Your LCD Display Viewing the Control Panel MENU button [MENU] Opens the on-screen menu and exits from the menu. Also use to exit the OSD menu or return to the previous menu. Navigate buttons (Up-Down buttons) Moves from one menu item to another vertically or adjusts selected menu values. Adjust buttons (Left-Right buttons) / Volume buttons Moves from one menu item to another horizontally or adjusts selected menu values. When OSD is not on the screen, push the button to adjust volume.
Introduction The product's Brightness Sensor function automatically detects the surrounding brightness using a brightness sensor and adjusts its brightness accordingly. Power indicator Shows PowerSaver mode by blinking green Note See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your LCD Display OFF when it is not needed or when leaving it unattended for long periods.
Introduction PC IN [RGB](PC Video Connection Terminal) Using a D-Sub Cable (15 pin D-Sub) - PC mode (Analog PC) DVI IN [HDCP] (PC Video Connection Terminal) Using a DVI Cable (DVI-D to DVI-D) - DVI mode (Digital PC) DC OUT Make sure to use connecting DC-OUT terminal to the authorized TV-Tuner Box[SBB-DT]. Otherwise, this may result in damage to the product.
Introduction Note The TV menu is available when a TV tuner box is installed. POWER OFF Number Buttons DEL button + VOL MUTE TV/DTV MENU INFO Color Buttons TTX/MIX STILL AUTO S.MODE MDC LOCK SOURCE ENTER/PRE-CH CH/P D.MENU GUIDE RETURN Up-Down Left-Right buttons EXIT SRS MagicInfo P.MODE DUAL/MTS PIP SWAP 1. POWER Turns the product On.
Introduction 2. Turns the product Off. Off 3. Number Buttons 4. DEL button Used to enter the password during the OSD adjustment or to use MagicInfo. The "-" button operates only for DTV. It is used to select MMS (multi-channel) for a DTV. 5. + VOL - Adjusts the audio volume. 6. Pauses (mutes) the audio output temporarily. This is displayed on the lower left corner of the screen. The audio resumes if MUTE or - VOL + is pressed in the Mute mode. MUTE 7.
Introduction 21. D.MENU DTV menu display 22. GUIDE Electronic Program Guide (EPG) display. 23. Returns to the previous menu. RETURN 24. Up-Down Left-Right buttons Moves from one menu item to another horizontally, vertically or adjusts selected menu values. 25. EXIT Exits from the menu screen. 26. SRS Selects SRS TruSurround XT mode. 27. MagicInfo MagicInfo Quick Launch Button. 28. P.MODE When you press this button, current picture mode is displayed on the lower center of the screen.
Connections Connecting a Computer Connect the power cord for your LCD Display to the power port on the back of the LCD Display. Turn on the power switch. There are 2 ways to connect the D-sub to your LCD Display. Choose one of the following: Using the D-sub (Analog) connector on the video card. • Connect the D-sub to the 15-pin, RGB port on the back of your LCD Display and the 15 pin D-sub Port on the computer. Using the DVI (Digital) connector on the video card.
Connections Connecting to Other devices Note AV input devices such as DVD players, VCRs or camcorders as well as your computer can be connected to the LCD Display. For detailed information on connecting AV input devices, refer to the User Controls under Adjusting Your LCD Display. Connecting a VCR AV input devices such as DVD, VCRs or Camcorders are connected via the AV IN [VIDEO] of the LCD Display using an cable.
Connections Connect a video cable between the VIDEO OUTPUT jack on the camcorder and the AV IN [VIDEO] on the LCD Display. Note • Select AV for the Camcorder connection using the SOURCE button on the front of the LCD Display or on the remote control. • Then, start the Camcorders with a tape inserted. • The audio-video cables shown here are usually included with a Camcorder. (If not, check your local electronics store.) • If your camcorder is stereo, you need to connect a set of two cables.
Connections Connecting Using a DVI to HDMI Cable Note • Connect the DVI output terminal of a digital output device to the HDMI IN terminal of the LCD Display using a DVI to HDMI cable. • Connect the red and white jacks of an RCA to stereo (for PC) cable to the same colored audio output terminals of the digital output device, and connect the opposite jack to the HDMI / PC / DVI AUDIO IN terminal of the LCD Display. Connecting a LAN Cable Note Connect the LAN cable.
Connections Note You can connect USB devices such as a mouse or keyboard.
Using the Software MDC (Multiple Display Control) Installation 1. Insert the installation CD into the CD-ROM drive. 2. Click the MDC installation file. Note If the popup window to install the software for the main screen is not displayed, proceed with the installation using the MDC executable file on the CD. 3. When the Installation Shield Wizard window appears, click "Next". 4. Select "I agree to the terms of the license agreement" to accept the terms of use. 5. Click "Install". 6.
Introduction A Multiple Display Control (MDC) is an application allowing various displays to be easily and simultaneously operated on a PC. RS-232C, a standard of serial communication, is used for the communication between a PC and a display. Therefore, a serial cable should be connected between the serial port on a PC and the serial port on a display. Main Screen Click Start > Program > Samsung > MDC System to start the program. Select a set to see the volume of the selected set within the slider.
Main Icons All Remocon Selection Buttons Safety Lock Refresh Port Selection Display Selection Lamp Control Info Grid Option... Control Tools Dropdown Selectors OSD Display 1. Use the main icons to switch into each screen. 2. Allows you to enable or disable the remote control signal receiving function of the display unit. 3. Set the Safety Lock function. When setting the Lock function, you can only operate power and lock buttons on the remote control and set. 4.
14. Switches the OSD function On/Off. - May not be supported depending on the product. The remote control Enable/Disable function operates whether or not the power is On/Off, and this applies to all displays connected to the MDC. However, regardless of the status at the time the MDC is shut down, the remote control signal receiving function of all displays is initialized to Enable when the MDC is closed. Port Selection 1. The Multiple Display Control is originally set to COM1. 2.
Info Grid shows some basic information necessary to Power Control. 1) (Power Status) 2) Input 3) Image Size 4) On Timer 5) Off Timer 2. Selects displays you want to adjust using the Select button or checkboxes.
Power Control allows controlling some of the functions of the selected display. 1) Power On/Off - Turns the power of the selected display On/Off. 2) Volume - Controls the volume level of the selected display. It receives the volume value of the selected display from the sets and displays it in the slider. (If you deselect a single display or all displays, the default value 10 will be restored.) 3) (Mute On/Off) - Turns on/off the Mute function of the selected display.
1) Source OSD - Sets whether the Source OSD will be displayed to indicate when the Source is changed. 2) Not Optimum Mode OSD - Sets whether the Optimum Mode OSD will be displayed to indicate if the current mode is not supported. 3) No Signal OSD - Sets whether the No Signal OSD will be displayed to indicate when there is no signal. 4) MDC OSD - Sets whether the MDC OSD will be displayed to indicate when the settings are changed using the MDC. Input Source 1.
• PC Mode Info Grid shows some basic information necessary to Input Source Control.
- Changes the Input Source of the selected display to PC. 2) BNC - Changes the Input Source of the selected display to BNC. 3) DVI - Changes the Input Source of the selected display to DVI. 4) TV - Changes the Input Source of the selected display to TV. 5) DTV - Changes the Input Source of the selected display to DTV. 6) AV - Changes the Input Source of the selected display to AV. 7) S-Video - Changes the Input Source of the selected display to S-Video.
Info Grid shows some basic information necessary to Image Size Control. 1) ( Power Status) - Shows the power status of the current display. 2) Image Size - Shows the current Image Size of the display in use. 3) Input - Info Grid displays only the displays whose Input Source is PC, BNC, DVI. 4) PC Source - When you click Image Size, the PC Source tab first appear. - The Image Size Control button controls Image Size available for PC, BNC, DVI.
Info Grid shows some basic information necessary to Image Size Control. 1) Click the Video Source tab to adjust Image Size for TV, AV, S-Video, Component, DVI(HDCP), HDMI, DTV. Selects displays you want to adjust using the Select button or checkboxes. 2) Info Grid displays only the display having TV, AV, S-Video, Component or DVI(HDCP) as input source. 3) Switch Image Size of the selected display randomly.
Info Grid shows some basic information necessary to Time Control. 1) Set clock - Set the current time for the selected display (PC Time). - To change the current time, first change the PC Time. 2) Timer - Sets up Timer1, Timer2, Timer3 and Holiday Management. 3) Shows whether Timer is activated. The Input source of MagicInfo works only on MagicInfo model. The Input source of TV works only on TV model. Time Control is available only for the displays for which the power status is ON.
1) On Time - Sets the time in hours, in minutes and as AM/PM for turning the selected monitor on. 2) Off Time - Sets the time in hours, in minutes and as AM/PM for turning the selected monitor off. 3) Volume - Selects the volume when the selected monitor is turned on. 4) Source - Selects the external input source that will be displayed when the selected monitor is turned on. 5) Holiday - Applies the Holiday Management function to the Timer.
1) Specifies the date. 2) Delete All - Deletes all of the holidays. 3) Add - Adds the specified date. 4) - Deletes the schedule in the selected line. The Holiday Management function can be turned on or off in the Timer setup menu. The Input source of MagicInfo works only on MagicInfo model. The Input source of TV works only on TV model. Time Control is available only for the displays for which the power status is ON. Only enabled for a TV when Source is set to TV in On Time mode.
Info Grid shows some basic information necessary to PIP Size Control. 1) PIP Size - Shows the current PIP Size of the display in use. 2) OFF - Turns off the PIP of the selected display. 3) Large - Turns on the PIP of the selected display and changes the size to Large. 4) Small - Turns on the PIP of the selected display and changes the size to Small. 5) Double 1 - Turns on the PIP of the selected display and changes the size to Double 1.
Info Grid shows some basic information necessary to PIP Source Control. 1) PIP Source - PIP Source can be controlled with turning on the LCD Display power. 2) PC - Changes the source of the PIP of the selected display to PC. 3) BNC - Changes the source of the PIP of the selected display to BNC. 4) DVI - Changes the source of the PIP of the selected display to DVI. 5) TV - Changes the source of the PIP of the selected display to TV. 6) DTV - Changes the source of the PIP of the selected display to DTV.
Settings Picture 1. Click Settings of the main icons and the Settings Control screen appears. Basic information required to adjust the Picture is displayed in the main menu. Settings for the selected monitor will be displayed if one of the connected monitors is selected, and the default settings will be displayed if all monitors are selected by clicking All and Select. If a value is changed in this screen, the current mode will automatically switch to custom mode.
- Adjusts the Brightness Sensor for the selected display. 10) Dynamic Contrast - Adjusts the Dynamic Contrast for the selected display. Brightness Sensor may not be supported depending on the product. The Input source of MagicInfo works only on MagicInfo model. Color Temp is only enabled if the Color Tone is set to Off. The Input source of TV works only on TV model. This feature is available only for the displays whose power status is ON and if no selection is made, the factory default is displayed.
- Adjusts red Color of the selected display. - Available only for NT. 5) Green - Adjusts green Color of the selected display. - Available only for NT. 6) Blue - Adjusts blue Color of the selected display. - Available only for NT. 7) Color Tone - Adjusts the Color Tone for the selected display. 8) Color Temp - Adjusts the Color Temp for the selected display. 9) Brightness Sensor - Adjusts the Brightness Sensor for the selected display.
Basic information required to adjust Audio is displayed in the display window. Settings for the corresponding SET will be imported and displayed on the slider if a display ID is selected, and the default settings will be displayed if all display IDs are selected by clicking All and Select. If a value is changed in this screen, the current mode will automatically switch to custom mode. 1) Audio - Controls audio settings for all input sources. 2) Bass - Adjusts Bass of the selected display.
Info Grid shows some basic information necessary to Settings Control. 1) Image Lock - Available only for PC, BNC. 2) Coarse - Adjusts Coarse of the selected display. 3) Fine - Adjusts Fine of the selected display. 4) Position - Adjusts Position of the selected display. 5) Auto Adjustment - Self-Adjust to the incoming PC signal. The Input source of MagicInfo works only on MagicInfo model. The Input source of TV works only on TV model.
An "Info Grid" showing several basic data items appears. 1) Maintenance - Allows the Maintenance Control function for all input sources. 2) Lamp Control - Automatically adjusts the backlight of the selected display at a specified time. The Manual Lamp Control automatically turns off if you adjust using the Auto Lamp Control. - Allows you to adjust the backlight of the selected display regardless of the time. The Auto Lamp Control automatically turns off if you adjust using the Manual Lamp Control.
1) Scroll - This function is used to remove the afterimages that occur when a still screen is displayed on the selected display for a long time. 2) Pixel Shift - This allows the screen to be moved finely at the specified time interval. 3) Safety Screen - The Safety Screen function is used to prevent afterimages from occurring when a still screen is displayed on the monitor for a long time.
1) Video Wall - A Video Wall is a set of video screens that are connected together, so that each screen shows a part of the whole picture or so that the same picture is repeated on each screen. 2) Video Wall Control - Video Wall properties can be configured.
1) On / Off - Turns on/off the Video Wall function of the selected display. 2) Format - The format can be selected to see a divided screen. z Full z Natural 3) Video Wall (Screen divider) - The screen can be divided into. You can select a number of screens with a different layout when dividing. z Select a mode from Screen divider. z Select a display from Display Selection. z The place will be set up by pressing a number in the selected mode.
The Input source of TV works only on TV model. The Maintenance Control function is available only for the displays where the power status is ON. Troubleshooting 1. The display you wish to control does not appear on the Power Control Info Grid - Check the connection of RS232C. (Check if it is properly connected to the Com1 port) - Check the displays to see if any of the other displays connected have the same ID.
Adjusting the LCD Display Input Available Modes • PC / DVI • AV • HDMI • MagicInfo • TV Note The TV menu is available when a TV tuner box is installed. Source List MENU → ENTER → [Input] → ENTER → [Source List] → , → ENTER Use to select PC, DVI or other external input sources connected to the LCD Display. Use to select the screen of your choice. 1. PC 2. DVI 3. AV 4. HDMI 5. MagicInfo 6. TV Note • The direct button on the remote control is the 'SOURCE' button.
Adjusting the LCD Display → , → ENTER Name the input device connected to the input jacks to make your input source selection easier. VCR, DVD, Cable STB, HD STB, Satellite STB, AV Receiver, DVD Receiver, Game, Camcorder, DVD Combo, DHR, PC Picture [PC / DVI / MagicInfo Mode] Available Modes • PC / DVI • AV • HDMI • MagicInfo • TV Note The TV menu is available when a TV tuner box is installed.
Adjusting the LCD Display High brightness For watching motion pictures such as a DVD or VCR. 2. Internet Medium brightness For working with a mixture of images such as texts and graphics. 3. Text Normal brightness For documents or works involving heavy text. 4. Custom Although the values are carefully chosen by our engineers, the pre-configured values may not be comfortable to your eyes depending on your taste. If this is the case, adjust the brightness and contrast by using the OSD menu.
Adjusting the LCD Display → , → ENTER Adjusts the Sharpness. Color Tone MENU → → , → ENTER → [Picture] → → →ENTER → [Color Tone] → ENTER The color tones can be changed. (Not available in Dynamic Contrast mode of On.) 1. Off 2. Cool 3. Normal 4. Warm 5. Custom Note If you set the Color Tone to Cool, Normal, Warm, or Custom, the Color Temp. function is disabled.
Adjusting the LCD Display → , → ENTER Green MENU → → ENTER → [Picture] → → [Green] → , → → → ENTER → [Color Control] → → ENTER → ENTER Blue MENU → → ENTER → [Picture] → ENTER → [Blue] → , → → → ENTER → [Color Control] → → → → ENTER Color Temp. MENU → → , → ENTER → [Picture] → → → → ENTER → [Color Temp.] → ENTER Color Temp. is a measure of the 'warmth' of the image colors. (Not available in Dynamic Contrast mode of On.) Note This function is only enabled if the Color Tone is set to Off.
Adjusting the LCD Display → , → ENTER Removes noise such as vertical stripes. Coarse adjustment may move the screen image area. You may relocate it to the center using the horizontal control menu. Fine MENU → → ENTER → [Picture] → → → → → ENTER → [Image Lock] → → ENTER → [Fine] → , → ENTER Removes noise such as horizontal stripes. If the noise persists even after Fine tuning, repeat it after adjusting the frequency (clock speed).
Adjusting the LCD Display Signal Balance This is used to make up for the weak RGB signal transmitted by a long signal cable. MENU → → ENTER → [Picture] → → → → → → → ENTER → [Signal Balance] (Available in PC mode only) (Not available in Dynamic Contrast mode of On.) Signal Balance MENU → → ENTER → [Picture] → → ENTER → [Signal Balance] → , → → → → → → ENTER → [Signal Balance] → → → → → ENTER → [Signal Balance] → ENTER Selects either On or Off with the signal control.
Adjusting the LCD Display → , 4. → ENTER R-Offset MENU → → ENTER → [Picture] → → → → → → → ENTER → [Signal Balance] → ENTER → → [Signal Control] → → → → ENTER→ [R-Offset] → , 5. → ENTER G-Offset MENU → → ENTER → [Picture] → → → → → → → ENTER → [Signal Balance] → ENTER → → [Signal Control] → → → → → ENTER→ [G-Offset] → , 6.
Adjusting the LCD Display → , → ENTER Dynamic Contrast automatically detects the distribution of the visual signal and adjusts to create an optimum contrast. 1. Off 2. On Brightness Sensor MENU → → ENTER → [Picture] → [Brightness Sensor] → , → → → → → → → → → ENTER → →ENTER Brightness Sensor is to automatically detect distribution of inputted visual signal and adjust to create optimum brightness. 1. Off 2.
Adjusting the LCD Display → , → ENTER The LCD Display has four automatic picture settings ("Dynamic", "Standard", "Movie" and "Custom") that are preset at the factory. Dynamic, Standard, Movie, or Custom can be activated. (Not available in Dynamic Contrast mode of On.) 1. Dynamic 2. Standard 3. Movie 4. Custom Note The direct button on the remote control is the 'P.MODE' button. Custom By using the on-screen menus, the contrast and brightness can be changed to your personal preference.
Adjusting the LCD Display Sharpness MENU → → ENTER → [Picture] → [Sharpness] → , → ENTER → [Custom] → → → ENTER → → ENTER Adjusts the picture Sharpness. Color MENU → [Color] → , → ENTER → [Picture] → → ENTER → [Custom] → → → → ENTER → → ENTER → [Custom] → → → → → ENTER → ENTER Adjusts the picture Color. Tint MENU → → [Tint] → , → ENTER → [Picture] → → ENTER Adds a natural tone to the display.
Adjusting the LCD Display 4. Normal 5. Warm1 6. Warm2 Note If you set the Color Tone to Cool2, Cool1, Normal, Warm1, or Warm2, the Color Temp. function is disabled. Color Temp. MENU → → , → ENTER → [Picture] → → → → ENTER → [Color Temp.] → ENTER Color Temp. is a measure of the 'warmth' of the image colors. (Not available in Dynamic Contrast mode of On.) Note This function is only enabled if the Color Tone is set to Off.
Adjusting the LCD Display Digital NR (Digital Noise Reduction) MENU → → , → ENTER → [Picture] → → → → → → ENTER → [Digital NR] → ENTER Turns the Digital Noise Reduction feature Off/On. The Digital Noise Reduction feature allows you to enjoy clearer and crisper images. 1. Off 2. On Film Mode MENU → → , → ENTER → [Picture] → → → → → → → ENTER → [Film Mode ] → ENTER The Film Mode feature offers you a theater-quality viewing experience.
Adjusting the LCD Display → , → ENTER Dynamic Contrast automatically detects the distribution of the visual signal and adjusts to create an optimum contrast. 1. Off 2. On Brightness Sensor MENU → → ENTER → [Picture] → → → → → → → → → ENTER → [Brightness Sensor] → , →ENTER Brightness Sensor is to automatically detect distribution of inputted visual signal and adjust to create optimum brightness. 1. Off 2.
Adjusting the LCD Display The LCD Display has a built-in high fidelity stereo amplifier. 1. Standard Selects Standard for the standard factory settings. 2. Music Selects Music when watching music videos or concerts. 3. Movie Selects Movie when viewing movies. 4. Speech Selects Speech when watching a show that is mostly dialogue (i.e., news). 5. Custom Selects Custom if you want to adjust the settings according to your personal preferences.
Adjusting the LCD Display → , → ENTER Allows you to Adjusts the sound balance between the left and right speakers. Auto Volume MENU → → , → → ENTER → [Sound] → → → ENTER → [Auto Volume] → ENTER Reduces the difference in volume control between broadcasters. 1. Off 2. On SRS TS XT MENU → → , → → ENTER → [Sound] → → → → ENTER → [SRS TS XT] → ENTER SRS TS XT is a patented SRS technology that solves the problem of playing 5.1 multichannel content over two speakers.
Adjusting the LCD Display • MagicInfo • TV Note The TV menu is available when a TV tuner box is installed. Language MENU → → , → → → ENTER → [Setup] → ENTER → [Language ] → ENTER You can choose one of 13 languages. Note The language chosen affects only the language of the OSD. It has no effect on any software running on the computer. Time Selects from one of 4 time settings, Clock Set, Sleep Timer, On Timer, and Off Timer.
Adjusting the LCD Display → , → ENTER Turns the LCD Display off automatically at certain times. 1. Off 2. 30 3. 60 4. 90 5. 120 6. 150 7. 180 On Timer MENU → → → → ENTER → [Setup] → → ENTER → [Time ] → → → ENTER→ [On Timer] → , / , → ENTER Turns the LCD Display on automatically at a preset time. Controls the mode and the volume level at the time the LCD Display turns on automatically.
Adjusting the LCD Display → , → ENTER / , Turns the LCD Display off automatically at a preset time. Menu Transparency MENU → → , → → → ENTER → [Setup] → → → ENTER → [Menu Transparency] → ENTER Change the transparency of the background of the OSD. 1. High 2. Medium 3. Low 4. Opaque Safety Lock PIN MENU → → → → ENTER → [Setup] → → → → ENTER → [Safety Lock PIN ] → [0~9, 0~9, 0~9, 0~9] → [0~9, 0~9, 0~9, 0~9] → [0~9, 0~9, 0~9, 0~9] The password can be changed.
Adjusting the LCD Display → , → ENTER This feature adjusts the power consumption of the unit in order to save energy. 1. Off 2. On HDMI Black Level MENU → Level ] → , → → → ENTER → [Setup] → → → → → → ENTER → [HDMI Black → ENTER When a DVD or set-top box is connected to your TV via HDMI, it may cause a degradation in the screen quality, such as an increase in the black level, a low contrast, or discoloration, etc., depending on the external device connected.
Adjusting the LCD Display Video Wall MENU → → → → ENTER → [Setup] → → → → Wall ]→ ENTER → [Video Wall ] → , → → → ENTER → [Video → → → ENTER → [Video → → → ENTER → [Video → ENTER Turns Off/On the Video Wall function of the selected display Off/On. 1. Off 2. On Format MENU → → → → ENTER → [Setup] → → → → Wall ]→ → ENTER → [Format] → , → ENTER The Format can be selected to see a divided screen. 1. Full Provides a full screen without any margins. 2.
Adjusting the LCD Display → , → ENTER Sets how many parts the screen should be divided horizontally. Five adjustment levels: 1, 2, 3, 4, and 5. Vertical MENU → → → → ENTER → [Setup] → → → → Wall ]→ → → → ENTER → [Vertical] → , → → → ENTER → [Video → → → ENTER → [Video → ENTER Sets how many parts the screen should be divided vertically. Five adjustment levels: 1, 2, 3, 4, and 5.
Adjusting the LCD Display Safety Screen The Safety Screen function is used to prevent afterimages that may appear when a still picture is displayed on the screen over a long time. • The Safety Screen function scrolls the screen for the specified period of time. • This function is not available when the power is turned off.
Adjusting the LCD Display Sets how many pixels the screen moves vertically. Five adjustment levels: 0, 1, 2, 3, and 4. Time MENU → → → → ENTER → [Setup] → → → → → → → → ENTER → [Safety Screen] → ENTER → [Pixel Shift] → → → → ENTER → [Time] → , → ENTER Set the time interval for performing the horizontal or vertical movement, respectively.
Adjusting the LCD Display You can change the Safety Screen Type. 1. Scroll 2. Bar 3. Eraser Period MENU → → → → ENTER → [Setup] → → → → → → → → ENTER → [Safety Screen] → → ENTER → [Timer] → → → ENTER → [Period] → , → ENTER Use this function to set the execution period for each mode set in the timer. Time MENU → → → → ENTER → [Setup] → → → → → → → → ENTER → [Safety Screen] → → ENTER → [Timer] → → → → ENTER → [Time] → , → ENTER Within the set period of time specify a time for execution.
Adjusting the LCD Display This function prevents after-images on the screen by moving all the pixels on the LCD according to a pattern. Use this function when there are remaining after-images or symbols on the screen, especially when you displayed a still image on the screen for a long time. Bar MENU → → → → ENTER → [Setup] → → → → Screen] → → → →ENTER → [Bar] → → → → ENTER → [Safety This function prevents after-images on the screen by moving long black and white vertical lines.
Adjusting the LCD Display → , → ENTER When the picture is not displayed properly on the screen when setting the graphics card resolution of the computer to 1024 x 768 @ 60Hz, 1280 x 768 @ 60Hz, 1360 x 768@ 60Hz or 1366 x768 @ 60Hz, by using this function(Resolution Select), you can have the picture displayed on the screen in the specified resolution. Note Available in PC mode only 1. Off 2. 1024 X 768 3. 1280 X 768 4. 1360 x 768 5.
Adjusting the LCD Display Side Gray MENU → → → → ENTER → [Setup] → → → → → → → → → → → ENTER → [Side Gray] → , → ENTER Select the brightness of the grey for the screen background. 1. Off 2. Light 3. Dark Reset Reverts the product settings to factory defaults. The Reset function is only available when PC / DVI is being used.
Adjusting the LCD Display OSD Rotation MENU → → → → ENTER → [Setup] → → → → → ENTER → [OSD Rotation ] → , → → → → → → → → → → → → → → → → → ENTER OSD Rotate 1. Landscape 2. Portrait Lamp Control MENU → → → → ENTER → [Setup] → → → → → ENTER → [Lamp Control ] → , → ENTER Adjusts the inverter lamp in order to reduce energy consumption. Note This function does not operate when Dynamic Contrast is set to On in PC, DVI, AV, HDMI, TV modes.
Adjusting the LCD Display Multi Control Assigns an individual ID to the SET. MENU → → → → → ENTER → [Multi Control ] → ENTER → , → [0~9] • ID Setup Assigns distinctive IDs to the SET. • ID Input Use to select the transmitter functions of the individual SET. Only a SET where the ID corresponds to the transmitter setting becomes activated. MagicInfo Available Modes • PC / DVI • AV • HDMI • MagicInfo • TV Note The TV menu is available when a TV tuner box is installed.
Adjusting the LCD Display • The preset password for the LCD Display is "000000". • The server program's Power-On option works only if the LCD Display's power is completely shut off. Please make sure not to use the Power-On option when the LCD Display is in the process of shutting down since this may cause system errors on the LCD Display. • When using MagicInfo with the MagicInfo Server Program: perform Network mode.
Adjusting the LCD Display In step 2 of MagicInfo Setup Wizard, you don’t have to go to Network Setting on the desktop to make your settings for TCP/IP. You just do that at step 2 of MagicInfo installation. 3. Select Language - step 3 When using multiple languages, you can choose and set a specific language among them. 4.
Adjusting the LCD Display You can select which rotation type will be applied to your device. 5. Setup Information Shows the settings that have been selected by the user. Note If the MagicInfo icon is not displayed on the notification area, double click the MagicInfo icon on the window desktop. The icon will appear.
Troubleshooting Self-Test Feature Check Note Check the following items yourself before calling for assistance. Contact a Service Center for problems that you cannot solve by yourself. Self-Test Feature Check 1. Turn off both your computer and the LCD Display. 2. Unplug the video cable from the back of the computer. 3. Turn on the LCD Display.
Troubleshooting • Do not use benzene, thinner or other flammable substances, or a wet cloth. 2) Maintaining the Flat Panel Display Screen. Clean with a soft cloth (cotton flannel) smoothly. • Never use acetone, benzene or thinner. (They may cause flaws or deformation of the screen surface.) • The user will be required to pay costs and related expenses for repairing damages caused. Symptoms and Recommended Actions Note A LCD Display recreates visual signals received from the computer.
Troubleshooting A: Check if the signal cable between the computer and the LCD Display is securely connected. Q: When the product’s internal cooling system operates, condensation may occur on the product surface under certain atmospheric temperature and humidity conditions. A: This symptom does not affect the product performance and will disappear as the atmospheric temperature and humidity conditions change.
Troubleshooting A: Adjust color using Custom under OSD Color Adjustment menu. Q: The color image is distorted by dark shadows. A: Adjust color using Custom under OSD Color Adjustment menu. Q: The color white is poor. A: Adjust color using Custom under OSD Color Adjustment menu. Q: The power Indicator blinks green. A: The LCD Display is currently saving the changes made to the settings to the OSD memory. Q: The screen is blank and the power indicator light is steady green or blinks every 0.
Troubleshooting A: Check if the power cord is securely connected. A: Check if a special fluorescent or neon lamp is on in the vicinity. Q: How can I change the frequency? A: The frequency can be changed by reconfiguring the video card. Q&A Note That video card support can vary, depending on the version of the driver used. (Refer to the computer or the video card manual for details.
Specifications General General Model Name SyncMaster 700DRN LCD Panel Size 70 " Diagonal (177 cm) Display area 1549.44 mm (H) x 871.56 mm (V) Pixel Pitch 0.807 mm (H) x 0.807 mm (V) Synchronization Horizontal 30 ~ 81 kHz Vertical 56 ~ 85 Hz Display Color 16.7 M Resolution Optimum resolution 1920 x 1080@ 60 Hz Maximum resolution 1920 x 1080 @ 60 Hz Input Signal, Terminated RGB Analog, DVI(Digital Visual Interface) Compliant Digital RGB 0.
Specifications Environmental considerations Storage Temperature : -4°F ~ 113°F (-20°C ~ 45°C) Humidity : 5 % ~ 95 %, non-condensing Plug and Play Capability This LCD Display can be installed on any Plug & Play compatible system. The interaction of the LCD Display and the computer systems will provide the best operating conditions and LCD Display settings. In most cases, the LCD Display installation will proceed automatically, unless the user wishes to select alternate settings.
Specifications Display Mode Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) MAC, 640 x 480 35.000 66.667 30.240 -/- MAC, 832 x 624 49.726 74.551 57.284 -/- MAC, 1152 x 870 68.681 75.062 100.000 -/- VESA, 640 x 480 37.861 72.809 31.500 -/- VESA, 640 x 480 37.500 75.000 31.500 -/- VESA, 800 x 600 35.156 56.250 36.000 +/+ VESA, 800 x 600 37.879 60.317 40.000 +/+ VESA, 800 x 600 48.077 72.188 50.000 +/+ VESA, 800 x 600 46.
Information For Better Display Adjust the computer resolution and screen injection rate (refresh rate) on the computer as described below to enjoy the best picture quality. You can have an uneven picture quality on screen if the best picture quality is not provided for TFT-LCD. • Resolution: 1920x1080 • Vertical frequency (refresh rate): 60 Hz TFT-LCD panels manufactured by using advanced semiconductor technology with a precision of 1ppm (one millionth) and above is used for this product.
Information Power Off, Screen Saver, or Power Save Mode • Turn the power off for 4 hours after 20 hours in use • Turn the power off for 2 hours after 12 hours in use • Set the Monitor to power off with the PC Display Properties Power Scheme. • Use a Screen saver if possible - Screen saver in one color or a moving image is recommended. Change the Color Information periodically Note Use Two different colors Rotate the Color Information with 2 different colors every 30 minutes.
Information • Avoid using a combination of characters and background color with large difference in luminance. Avoid using Grey colors, which can cause Image retention easily. Avoid: Colors with big difference in luminance (Black & White, Grey) Change the characters color periodically • Use Bright colors with little difference in luminance. - Cycle : Change the characters color and background color every 30 minutes • Every 30 minutes, change the characters with movement.
Information - Symptom: Dot with Black Color move up and down. • Apply the Screen Bar function - Symptom: Horizontal / Vertical Bar with Black Color move up and down. Note ( Please check CD's User Guide at "OSD Function", some model's will not available.
Appendix Contact SAMSUNG WORLDWIDE Note If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center. North America U.S.A 1-800-SAMSUNG(726-7864) http://www.samsung.com CANADA 1-800-SAMSUNG(726-7864) http://www.samsung.com MEXICO 01-800-SAMSUNG(726-7864) http://www.samsung.com Latin America ARGENTINA 0800-333-3733 http://www.samsung.com BRAZIL 0800-124-421 http://www.samsung.com 4004-0000 CHILE 800-SAMSUNG(726-7864) http://www.samsung.
Appendix Europe FINLAND 030 - 6227 515 http://www.samsung.com FRANCE 01 4863 0000 http://www.samsung.com GERMANY 01805 - SAMSUNG (7267864, € http://www.samsung.com 0,14/Min) HUNGARY 06-80-SAMSUNG (726-7864) http://www.samsung.com ITALIA 800-SAMSUNG (726-7864) http://www.samsung.com LATVIA 8000-7267 http://www.samsung.com LITHUANIA 8-800-77777 http://www.samsung.com LUXEMBURG 261 03 710 http://www.samsung.com NETHERLANDS 0900-SAMSUNG (0900-7267864) ( € 0,10/Min) http://www.samsung.
Appendix Asia Pacific HONG KONG (852) 3698 - 4698 http://www.samsung.com/hk http://www.samsung.com/ hk_en/ INDIA 3030 8282 http://www.samsung.com 1800 110011 1800 3000 8282 1800 266 8282 INDONESIA 0800-112-8888 http://www.samsung.com 021-5699-7777 JAPAN 0120-327-527 http://www.samsung.com MALAYSIA 1800-88-9999 http://www.samsung.com NEW ZEALAND 0800 SAMSUNG (0800 726 http://www.samsung.com 786) PHILIPPINES 1-800-10-SAMSUNG (726-7864) http://www.samsung.
Appendix Example: If the same light repeats itself 60 times per second, this is regarded as 60 Hz. Horizontal Frequency The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle. The inverse number of the Horizontal Cycle is called Horizontal Frequency.
Appendix Correct disposal of batteries in this product - Europe only (Applicable in the European Union and other European countries with separate battery return systems.) This marking on the battery, manual or packaging indicates that the batteries in this product should not be disposed of with other household waste at the end of their working life. Where marked, the chemical symbols Hg, Cd or Pb indicate that the battery contains mercury, cadmium or lead above the reference levels in EC Directive 2006/66.
