Digital Video Recorder 1 User’s Manual
Introduction Thank you for purchasing the SVR-940/450. ThisisausermanualforSVR-940/450.Beforeproductinstallationandoperation,pleasebecomethoroughly familiar with this user manual and other manuals referenced by this manual. Thisusermanualandthesoftwareandhardwaredescribedhereareprotectedbythecopyrightlaw.
Table of contents Introduction·····························································································································································2 Product warranty and limits of responsibility·····························································································2 Chapter 1. Safety Cautions································································································································5 Chapter 2.
Table of contents 5.3 Menu Screen Setup······································································································································42 5.4 SCREEN SETUP···············································································································································43 5.4.1 CH1~CH4 / CH1~CH9 (for SVR-940)·······························································································43 5.4.
Chapter 1. Safety Cautions Symbols displayed for each item Warning Referstoinformationusersneedtoknowinordertopreventseriousinjuryor death. Caution Providesinformationusersneedtoknowinordertopreventminorinjuryor product damage. • Before installation - Verify the supplied voltage (AC100V~AC240V) before connecting the power supply. - Make sure the power supply is off before installation. - Do not install in a very humid environment. Doing so may cause an electric shock or fire.
Chapter 1. Safety Cautions • During use - Make sure the product is not exposed to shocks or shaking when using the product or during moving. - Donotmovetheproductwhileitisinoperation,andapplystrongshockstotheproductorthrowtheproduct. - Ifharddiskdrivesotherthanthoserecommendedareusedadditionally,abnormaloperationmayoccur.Inquire at the point of purchase of the product before installing such a hard disk drive. - Product warranty will not cover deliberate additional use of such hard disk drives.
Chapter 2. Summary The Samsung SVR-940/SVR-450 is a digital video recorder designed to be used as a security device insmallshops,conveniencestores,banks,ATMs,etc.Itisastand-alonedevice,securingsystemperformanceandsafety.TheSamsung SVR-940/SVR-450 saves video images on an HDD instead of on videotape. It can save quality images even with repeated recording, and facilitates data search by recordingandplayingvideodatainadigitalfileformat.
Chapter 2. Summary Storage Media Thebuilt-inHDDisthebasicmemorysupply.UsingaUSBmemorystickorexternalCD-RW(guaranteed for the recommended models only), users can copy images from the internal HDD. . Basic Memory Supply: Built-in HDD . Backup media: USB memory stick . Backup media: Built-in CD-RW • CD-RW-Maker : LITEON CO., LTD Model : LTR-52327SX Model : SHM-165P6SX02C • CD MEDIA-Maker : SAMSUNG Model:PLEOMAX R80X5210SJ Network TheSamsungSVR-940/SVR-450supportsawiderangeofnetworkssuchasLANandADSL,DHCP.
Chapter 2. Summary 2.2 Contents TheSVR-940/SVR-450packagecontainsthemainunitanditscomponentsasspecifiedbelow.When youpurchasetheunit,pleasecheckthatthecomponentsspecifiedbelowareincluded.Ifanycomponents are missing, please contact your local vendor. SVR-450/940 Main unit 1. Network viewer program CD 2. User Manual 3. Remote controller 4. Batteries for remote controller 5. Adaptor (For SVR-450) 9. Power cable 2.2.
Chapter 2. Summary LED Indication Number LED Name Description 1 Lights up when power is applied to the system 2 Lights up when the system is backing up. 3 Lights up when an Alarm is triggered. 4 Lights up when client has connected to the system through the Network 5 Lights up when the system is accessing HDD 6 Lights up when the system is recording video data Button Indication Number Button Name Description 1 Press to power the system ON/OFF.
Chapter 2. Summary ButtonIndication Number Button Name Description 7 Playback position moves 1 frame forward/back during Pause. 8 Press to start and stop manual recording 9 Press to search the recorded data 10 Press to launch Setup Menu 11 Press to control the PTZ functions 12 Press to backup still images or video 13 PresstostartscreenAutoSequence.Set°ÆSCREENSETUP/AUTO SEQUENCE/SEQUENCE°Ø as °ÆON°Ø.
Chapter 2. Summary 2.2.2 Rear Connection terminals Rear panel of SVR-450 Rear panel of SVR-940 1. VIDEO IN Camera Input (NTSC/PAL) 2. AUDIO IN Audio Input 3. AUDIO OUT Audio Output 4. VIDEO OUT Composite Video Output 5. VGA VGA output 6. RS-232 For the engineering console only, not for other purposes. 7. LAN RJ45 Connector 8. RS-485/422 PTZ camera control 9. SENSOR IN Sensor Input 10. ALARM OUT Alarm Output 11. SWITCHES NTSC/PAL, BNC/VGA Select Switch(Please refer to Chapter 5 for the detailed guide.
Chapter 2. Summary 2.2.3 Remote controller • MENU Button to enter Setup Menu • AUTO For Auto Sequence • SPOT Button for Spot ON/OFF (SVR-940.) • PTZ Button for PTZ camera control. • COPY Button for data backup. • RECORD Button for Manual record ON/OFF. • STOP Button to stop playback. • SEARCH Button for search menu. • STEP Playbackpositionmoves1frameforward/backduring Pause. • PLAY/PAUSE Button to Play and Pause the Playback screen • FAST Button for Forward Playback. Speeds of 2X, 4X, 8X.
Chapter 2. Summary Video Items Input Method SVR-450 SVR-940 Composite Input 4-Channel Composite Input 9-Channel Video Input Level 1.0 Vp-p, Composite Live Screen Display Speed Live Screen Monitor Output VGA Output Real time display NTSC: 720 (W) _ 480 (H) Pixels for the full screen. PAL: 720 (W) _ 576 (H) Pixels for the full screen 8bit Brightness (256 Gray Scale) 24bit Color (160,000 Colors) 1.0Vp-p Composite, 75Ω 1.
Chapter 2. Summary Recording Items SVR-450 SVR-940 MaximumNumberofFrames Sec per Resolution (NTSC) 720X480: 30 Frames/Sec 360X240: 120 Frames/Sec 720X480: 30 Frames/Sec 720X240 : 60 Frames/Sec 360X240: 120 Frames/Sec Recording Method Pre-Event Recording Image Quality 3 Types of Recording Mode: General, Schedule, & Event Individual Channel ON/OFF Setting 3-Stage Image Quality: User Configurable HDD Items Default HDD HDD type RPM Recommended Notes SVR-450 SVR-940 1 ea (Max. 1ea) 1 ea (Max.
Chapter 2.
Chapter 2. Summary UserEnvironment Items Operating Temperature Storage Temperature Humidity SVR-450 SVR-940 5˚C~ 40˚C 10˚C~60˚C 30% ~90%(without dewfall) Exterior Items Material Dimensions Weight SVR-450 SVR-940 Steel Case 260(W) X 350(D) X 65(H)mm About 5.
Chapter 3. Installation 3.1 How to connect all parts The connection layouts for the SVR-450/940 with the monitor, CCTV, and external devices are described as below.
Chapter 3. Installation 3.2 Detailed connection 3.2.1 Camera The SVR-450 and 950 can accommodate up to 4 or 9 cameras respectively. Connect the BNC terminal of each camera to the CAMERA IN terminal of the unit. SVR-450 SVR-940 3.2.2 Audio TheSVR-450/950cansaveaudioinformation.Forstorageoroutputofaudioinformation,itisrequired to connect the relevant devices.
Chapter 3. Installation SVR-940 Audio input PleaseconnectanRCAaudiocabletotheAUDIOINconnector(suchascamerawithbuilt-inmicrophone and others). (All types of microphone and speaker are compatible with the system.) Notes • For Audio input setting, set [Audio] to [ON] in the Recording setting menu PleaseconnectanRCAaudiocabletotheAUDIOOUTPUTconnector(suchasmonitorwithbuilt-inspeakers).
Chapter 3. Installation SVR-940 Caution • TheVideo output and theVGA output cannot be used at the same time and the systemcansendonlyonevideooutatthesametime.PleaserefertoChapter4.1 Checklist before operation for the setting of monitor selection. • DuringplaybackwiththeVGAmonitor,afewframescansometimesbemissingbut this is not a defect of the unit. 3.2.
Chapter 3. Installation SVR-450(1-ALARMOUT) SVR-940(4-ALARMOUT) Notes • TheoperationofeachrelayoutputcanbedefinedbyacombinationofMotionDetect, andSensorintheEventSettingontheMainMenu.SeeParagraph4.5.3CH1~CH4 Relay Setting for details External Control Device Terminal (RS-422/485) Thisterminalisconnectedtoexternalcontroldevices.TheinternalJP2terminationterminalturnsthe terminator resistance of the RS-422/485 communication device on and off.
Chapter 3. Installation SVR-940 1. RS-422 : Connecting Terminal Block's 4 Port orderly 2. RS-485 : Connecting 3 & 4 ports to RS-485 No. Description Classification RS-422 RS-485 1 TX+(+Transmit Data) - 2 TX-(- Transmit Data) - 3 RX+(+Receive Data) Data+ 4 RX-(- Receive Data) Data- LAN Connection (Ethernet 10/100 Base-T) This port is to connect to network.
Chapter 3. Installation SVR-940 No. Description No. Description 1 TX+(Transmit Data) 5 N/C(No connection) 2 TX-(Transmit Data) 6 RX-(Receive Data) 3 RX+(Transmit Data) 7 N/C(No connection) 4 N/C(No connection) 8 N/C(No connection) Monitor Output (VGA) This is the output connector for a VGA Monitor.
Chapter 3. Installation No. Description No. Description 1 Red Signal (75, 0.7Vp-p) 9 N/C(No connection) 2 Green Signal (75, 0.7Vp-p) 10 Ground 3 Blue Signal (75, 0.7Vp-p) 11 Ground 4 N/C(No connection) 12 N/C(No connection) 5 Ground 13 HSYNC(HorizontalSynchronization) 6 Ground 14 VSYNC (Vertical Synchronization) 7 Ground 15 N/C(No connection) 8 Ground Chapter 4. Operating 4.
Chapter 4. Operating SETTING Video mode Video output NTSC PAL BNC VGA O X X O X O X O Factory Default * The factory default is set to NTSC video mode and VGA video output. 4.2 Power connection · After power is connected to the rear connector of the system, the system will be powered on. · When power is turned on, the system will detect a video signal automatically. · Despite of a power failure, all the setting values will preserve. 4.
Chapter 4. Operating 4.3.1 Function of screen display When Channel number buttons 1 ~ 4 (SVR-450) / 1 ~ 9 (SVR-940) are pressed, each channel is displayed in full screen. Press the ENTER button, and the four connected channels are displayed in quad split screen 4.3.2 Automatic channel rotation When the AUTO button is pressed in each full screen mode, each channel is rotated automatically following the setting in [SCREEN SETUP] > [Auto Sequence]. (SEQUENCE must be set to [YES].
Chapter 4. Operating 4.4 Recording 4.4.1 Normal recording WhentheRECbuttonispressed,manualrecordingisstartedandthe"R"icon(ManualRecording)is displayed on the upper right corner of the monitor screen. WhentheRECbuttonispressedagain,themanualrecordingisstoppedandthepre-recordingsetting isactivated.Whilerecordingwiththepre-recordingsetting,theiconsbelowindicatethetriggerfor recording.
Chapter 4. Operating 4.5 Search PresstheSEARCHbutton,andtheSearchMenuappearsasillustratedbelow.Recordedvideocanbe searched and played back by time, event, or date and the Log File is also displayed. 4.5.1 Event search FromtheEventSearchmenu,therecordeddatacanbesearchedbyMotiondetectionrecording,Sensor recording, Text recording, Manual recording, etc. When Event Search is selected, the screen below is displayed. · Dates with any recorded data are displayed in a dark color.
Chapter 4. Operating · V1~V4 : Time zones with recorded data are displayed with a colored bar. (SVR-940 : V1~V9) · A1~A4 : Time zones with recorded audio data are also displayed with a colored bar. Time zones with recorded data are displayed in colors. 4.5.3 Go To search Users can enter a desired search date and time in this menu. Press the ENTER button to display as below. Users can enter a desired search date and time and press the PLAY button to playback.
Chapter 4. Operating 4.5.6 Log file search PresstheENTERbuttononthismenutodisplaythecalendar.Selectadesireddateonthecalendarto display the Log files. Press the ESC button to exit this menu. 4.5.7 COPY List BothStillimagesandVideocanbebackedup.ThemaximumbackuptimeforVideoisupto999seconds. Notes • During backup, the system will not record, to ensure system stability. 4.5.7.1 Still image Backup ① Duringmonitoring,PresstheCOPYbuttonifyouwishtocaptureanimage.
Chapter 4. Operating Figure 3 4.5.7.2 Video backup: Only available during Playback mode ① DuringPlayback,PressthePAUSEbuttontopausetheplaybackandpresstheCOPYbutton.Youwillbeasked whethertostoreaStillimageorVideo(Figure1).SelectVideoandsetthedurationofthecopytostorethedatainto theHDD,andselectthebackupdevice-eitherUSBmemorystickorCD-RW.Selectthedevicethatyouwanttosave it to and it will be saved to that device. ② PresstheSEARCHbuttonandselectARCHIVEtodisplaythecalendar.
Chapter 4. Operating Figure 3 4.6 Playback REC Button for manual recording. STEP Playback position moves 1 frame forward/back during Pause. PLAY/PAUSE Button for playback and pause. STOP Button for stop FAST Button for fast forward. DIR Button to select and change the direction of play in playback. Notes • Duringplayback,afewframesmaybemissingdependingontheimagequality,but this is not a defect of the unit. 4.
Chapter 4. Operating SEARCH MENU PTZ COPY AUTO MULTI 4.7.1 PAN/TILT Select PAN/TILT and press the ENTER button. button - For Pan adjustment, Press the - For Tilt adjustment, Press the button 4.7.2 ZOOM/FOCUS Select ZOOM/FOCUS and press the ENTER button. - For Zoom adjustment, Press the - For Focus adjustment, Press the button. button 4.7.
Chapter 4. Operating 4.8 DVR Backup File Player TheDVRprovidesanexclusivevideofileformataswellasAVIfiletype.ToplayandseetheDVR(exclusive) type file, you should play back this video file on our exclusive player as follow. (Notice: WhentheMPEG-4Codecisnotinstalled,theexclusiveplayercannotplaytheDVRformatfile.Inthis case,FFDSHOWCodec(ffdshow.exe)onnetworkclientsoftwareCDthatisprovidedinthepackage should be installed and run before the playback of the DVR format backup file.
Chapter 4. Operating 4. Select the backup file (DVR type) you wish to playback 5. ClicktheplaybuttontostartplaybacktheDVR file you selected. Click to start playback the selected file 6. Overview of DVR Player 1 2 3 4 5 6 7 8 9 Table 1. DVR Player Buttons No.
Chapter 5. Configuration 5.1 Menu configuration Press the Menu button on the front side of the unit or the MENU button on the remote control, and the menu for a variety of settings related to the unit will appear.The menu is configured as described below. Notes • The factory default language is English. See Paragraph 4.10.4 - Other Settings for Language setup. Event setup Record setup Network setup Screen setup System setup The menu is configured as illustrated below.
Chapter 5.
SS Chapter 5. Configuration 5.2 Default Setup TheSVR-450/940aredeliveredtocustomerswiththefactorydefaultvaluesasdescribedbelow.To initializethemenusetuptothefactorydefaultvalues,select[YES]forthe[DEFAULT]itemin[SYSTEM SETUP]-[ETC] on the menu. Then all setting values changed by users are initialized to the default values as illustrated below.
Chapter 5.
Chapter 5.
Chapter 5. Configuration 5.3 Menu Screen Setup Select the MENU button on the remote control or the main unit, and the following Menu Screen appears. MAIN MENU SUB MENU SETUP SETUP GUIDE Notes • Press the MENU button, and the background screen is switched to the quad split screen. · Main Menu: Select the Main Menu corresponding to each Tab. · Submenu: Select the Submenu to be set up on the Main Menu. · Setup Items: Change the settings on the Submenu.
Chapter 5. Configuration 5.4 SCREEN SETUP This is the set up menu related to the DVR system. Press the MENU button and select theTab using the Left/Right button.Then the submenu related to the system appears as illustrated below. Press theENTERbuttonandselectthesubmenuusingtheLeft/Rightbutton.ThenpresstheENTERbutton again and you can select setup items using the Left/Right button. 5.4.1 CH1~CH4 / CH1~CH9 (for SVR-940) Select setup items related to channels such as channel titles or brightness.
Chapter 5. Configuration . BRIGHTNESS : Adjusts the screen brightness by changing the values. . CONTRAST : Adjusts the screen contrast by changing the values. 5.4.2 AUTO SEQUENCE The live screens are automatically switched in the order of [SVR-450: CH2 -> CH3 -> CH4 ] / [SVR940: CH2 -> CH3 -> CH4 -> CH5 -> CH6 -> CH7 -> CH8 -> CH9 >] at the predefined switching interval. The channel switching interval can be set from 1 up to 10 on the [SEQUENCE] menu. .
Chapter 5. Configuration · OSD [ON/OFF] : With OSD [ON], Status information is displayed on the live screen. ·CLOCKDISPLAY[ON/OFF]:WithClockDisplay[ON],thecurrenttimeisdisplayedonthelivescreens. · HDD FREE SPACE [ON/OFF] : WithHDDFreeSpace[ON],thefreespaceforrecordingontheHDDis indicated. · RECORD STATUS [ON/OFF] : WithRecordStatus[ON],therecordingstatus"S"isdisplayedonthecorner of the screen during recording.
Chapter 5. Configuration 5.5 RECORD SETUP This is a set up menu related to the DVR system. Press the MENU button and select the Tab using the Left/Right button.The submenu related to the system then appears as illustrated below. Press theENTERbuttonandselectthesubmenuusingtheLeft/Rightbutton.ThenpresstheENTERbutton again and you can select setup items using the Left/Right button. 5.5.1 GENERAL SETUP 1. IMAGE SIZE Recording Resolution can be selected.
Chapter 5. Configuration 5.5.2 DETAIL SETUP . CHANNEL : Select the channel for which to set DETAILED SETUP. MODE : Select one of four recording methods below. CONTINUOUS Continuous recording mode for 24 hours a day SCHEDULE Reserved recording MOTION DETECT Recordingisactivatedwhenthesystemdetectsmotionfrominputvideo images. SENSOR Recording is activated when the system detects sensor operation.
Chapter 5. Configuration A Schedule can be set 24 hours a day. · S : Sensor record · - : No record · C : Normal record · M : Motion detection record · T : Text record IMAGEQUALITY[High/Mid/Low]:Setthecompressionlevelforimagestobestored.Ataresolutionof 720X480,thesystemrecordsatmax.30fps.Ataresolutionof360X240,thesystemrecordsatmax.12fps. PRE EVENT DURATION : Thisisthepre-eventrecordingsetup.Itautomaticallyrecords5secondsof pre-eventdataifyousetitto5secs.Pre-eventrecordingisnotactivatedifyou set it to OFF.
Chapter 5. Configuration SENSOR : Select the channel for sensor setup. - SENSOR TYPE : Select the sensor type. (N/O, N/C) - N/O : NORMAL OPEN type sensor - N/C : NORMAL CLOSE type sensor - OFF : Set the sensor OFF 5.6.2 MOTION DETECTION After setting RECORD MODE/MOTION, set the motion detection for every CHANNEL : Select the channel for motion detection setup. MOTION ZONE : Select the area for motion detection to Full or Partial zone. -FULLZONE:DetectsmotionbyanalyzingthechangesinFullimagesfromcameras.
Chapter 5. Configuration · SYNC CHANNEL: Select the channel to display TEXT data from a POS device. · DEVICE -NORMAL:SelectNORMALwhenconnectinganormalinputdevicesuchasabarcodescanningdevice. - Finger 007 : Select 'Finger007' when connecting a finger print scan device. · CHECK PROTOCOL - HEADER1 - HEADER2 - DELIMITER - LINES : Set the number of lines to display TEXT data. 5.6.4 POS quick guide ConnectthesystemtothePOSdeviceusingaserialcable.
Chapter 5. Configuration Kalatel Quick-Easy Mart 3197 Airport Loop Drive Costa Mesa, Ca. 92626 Candy Bar $1.49 Soft Drink 64oz. $2.49 Chips $0.99 --------------------------TOTAL $ 7.99 POS scenario LIVE SCREEN POSTEXT data is displayed only over a full screen, not on quad split screen, and is displayed for 3 to 4 seconds. PLAYBACK SCREEN POS TEXT data is displayed only over a full screen, not on quad split screen. Whenthelinkedchannelisdisplayedinfullscreen,theTEXTdataisdisplayedovertheplaybackscreen.
Chapter 5. Configuration 5.7 NETWORK 5.7.1 NETWORK Set the necessary items for network connection to a computer. · NETWORK TYPE [ADSL/LAN/DHCP] : Selects the network type to connect to a computer. · IP ADDRESS : Enters the [IP ADDRESS] that the relevant Internet service provider assigns to a user. · SUBNET MASK : Entersthe[SUBNETMASK]addressthattherelevantInternetserviceproviderassigns to a user. ·GATEWAY:Entersthe[GATEWAY]addressthattherelevantInternetserviceproviderassignstoauser.
Chapter 5. Configuration This is all about DDNS setup in the DVR unit. 2) Afterfinishingtheabovestep,pleasetakethenextstepwiththeDDNSserver.PleaserefertoChapter 5.8 DDNS Registration. 5.7.3 Client access · PORT : When connecting to a PC, the ports can be changed. To connect the SVR-450 to a router, all three ports need to be set..
Chapter 5. Configuration 5.7.4 RS-232 This menu is for setting a connection with a POS device. · SYSTEM ID : Set the system ID. · BAUD RATE : Set the data transfer speed per second. · DATA BIT : Set the data transfer bit-rate. · PARITY BIT : Set the type of error checking for data transfer. · STOP BIT : Set the insert bit after data transfer. 5.7.5 RS-422/485 This menu is for setting a connection with Cameras and CCTV devices. · SYSTEM ID : Set the system ID.
Chapter 5. Configuration · SEND E-MAIL : Select ON for E-mail sending. · MAIL ADDRESS : PresstheENTERbuttontodisplaytheKeyboardscreenandselectthecorrectE-mail address. · MAIL SERVER IP: Please keep the default value. ID : Input the registered ID of the MAIL SERVER. PW : Input the registered PW of the MAIL SERVER. · RETURN MAIL ADDRESS : Inputthee-mailaddresstoreturnanundeliveredmailtothemailaddressthat is set from MAIL ADDRESS. 5.8 DDNS Registration 5.8.1.
Chapter 5.
Chapter 5. Configuration 2)The product registration is possible after sign up.
Chapter 5. Configuration - Check the registration at product list 3) DDNS Configuration at DVR Press the MENU button, then select [Network] on OSD Menu. • DDNS > Select ‘Yes’ • DDNS SERVER DOMAIN NAME > Enter the DDNS server address (Default:www.samsungipolis.com) • ID & PW > Enter the ID(Domain) & Password using the product registration at iPOLiS website. The DDNS configuration at DVR is completed.
Chapter 5. Configuration 4) The connection status of selected product can be checked on product list. [VIEW] : See the log-in page of selected product [Edit]/[Delete] : Edit/Delete the selected product, password is needed for checking Caution •The product ‘ID(domain)’ can not be changed at registered status. WhentheproductneedstochangetheID,firstofall,deletethedesiredproduct,and register product again. 5.9. Instructions on using DDNS 1) Product information confirmation.
Chapter 5. Configuration - under ‘Product Information’ - Checking the product information (Product, Model Number, ID(Domain), MAC Address, etc) 2) Video playback function - View : Move to the login web page of selected product. Caution • Ifyouwanttomultichannelslivemonitoring,searching/playbacksimultaneously, werecommendtousingSNM-64S/Ps/wprogram.TheiPOLiSwebsitedoesn't support multi [View] connection at one PC. 3) Product maintenance functions.
Chapter 5. Configuration i. Editing product profile - Click the edit button from the product list 5.10 Editing registered product ii.
Chapter 5. Configuration 5.11 System setting This is a set up menu related to the DVR system. Press the MENU button and select the Tab using the Left/Right button. The submenu related to the system appears as illustrated below. Press the ENTERbuttonandselectthesubmenuusingtheLeft/Rightbutton.ThenpresstheENTERbuttonand you can select setup items using the Left/Right button. 5.11.1 System · LANGUAGE : SelectsthelanguagefortheMenuscreen.10languagesincludingKoreanandEnglishare available.
Chapter 5. Configuration · TEST MODE : Select to upgrade the firmware of the system. Please refer to Chapter 5.14.1 Firmware upgrade. 5.11.2 HDD HDD FORMAT : SelectwhethertoinitializetheHDD.SelectONtodeletealldatasavedintheHDDand the unit will automatically reboot for system stabilization. HDD DESCRIPTION : Detailed information such as the size, and recording start time of the HDD.
Chapter 5. Configuration 5.11.3 Password Set the Admin and Network Passwords and set each limitation according to each password. The DVR supports one ADMIN and three USER accounts. · USER AUTHENTICATION : The DVR requires each user to sets up a password in order to be able to control the given functions. The password should consist of four numbers. (e.g.1,2,3,4) · USER PASSWORD : Set the user password.
Chapter 5. Configuration 1. Authorization functions - Administrators build the system considering the two factors below. i. Select the functions whose use is to be restricted. ▶PASSWORD CHECK = O : Function that only a designated person can use. ∴ The USER who uses the function must be selected. → Inordertoexecutethefunction,thedesignatedUSER(theUSERwhoisselectedontheLISTas 'O') must obtain authorization using his own PASSWORD. ii. Select the functions whose use is not to be restricted.
Chapter 5. Configuration 5.11.5 CLOCK SETUP Set the system date. · CLOCK : Set the system time. The unit will automatically reboot for system stabilization. - DAYLIGHT SAVING : Select whether to apply Daylight Saving Time. - DATE SETUP : Set the system time. - NTP : NPTisanabbreviationforNetworkTimeProtocol,whichisforsynchronizingtheclocks of computer systems over variable-latency data networks. - TIME SERVER : Input the address of the NTP TIME SERVER.
Chapter 5. Configuration 5.12 PTZ This is a set up menu related to the DVR system. Press the MENU button and select the Tab using the Left/Right button. The submenu related to the system appears as illustrated below. Press the ENTERbuttonandselectthesubmenuusingtheLeft/Rightbutton.ThenpresstheENTERbuttonand you can select setup items using the Left/Right button. 5.12.1 Setting for each channel Set the camera ID and model for each channel. · CHANNEL : Select the channel to set.
Chapter 5. Configuration 5.14 ETC 5.14.1 Firmware Upgrade Userscanupgradethesoftwarebydoingafirmwaredownload.Youcandownloadthefirmwarewith a USB Memory stick. ① Select 'MENU' and go to [SYSTEM SETUP]-[SYSTEM]-[TEST MODE]. ② The DVR will reboot and the system will show the DVR DIAGNOSTICS MENU as below. ③ PleasecreateafolderintheUSBmemorystickandnameit'UPGRADE'.Copytheupgradefileinto the folder and connect the USB memory stick to the DVR. Thefolder'snamemustbe'upgrade'.
Chapter 5. Configuration 5.14.2 Index Start Fail WhentheDVRsystemtimeisresetormismatched,themessagebelowisdisplayed.Thismessageis displayedwhentheDVRsystemtimeissettobeforeofthetimerecordingdataontheHDD.IftheDVR system time is set correctly, the DVR will not show the 'TIME MISMATCH' error message. ① When the above message is displayed, power the system OFF. Please the power the system ON, pressingtheESCbutton.(PresstheESCbuttonandholdituntiltheinitialmessageisdisplayedon thescreenasbelow.
Chapter 5. Configuration ③ After setting the YEAR/MONTH/DATE/HOUR/MIN/SEC, press the ENTER button. ④ Pleasesetthetimecorrectly.IfthetimeoverlapsthefinalrecordingdateontheHDD,theoverplayed data will be deleted. . ⑤ The DVR will be rebooted. Select BOOT APPLICATION. Caution • Please check if the USB memory stick is compatible with the DVR - SAN DISK CO, PRETEC , LG, INNOTECH C&C, TRANSCEND, etc. • “TESTMODE”,“FACTORYDEFAULT”,“MACCONFIGURATION”isformanufacturer’suse only. Please do not touch. Chapter 6.
Chapter 6. Web-Viewer Items Description Connection Type If the system is using a Dynamic IP address, select 'iPolis Server'. Tousethisfunction,thesystemmustbepre-registeredintheiPOLiShome page and the NETWORK menu of the system must be properly pre-set. IP/Domain Input the IP address of the system if the 'Connection Type' is 'IP Address'. When the 'Connection Type' is 'iPolis Server', the default setting value is displayed. The default setting value is www.samsungipolis.
Chapter 6. Web-Viewer Buttons / / Functions Button to select screen display from 4/ 9/ 16 channels. (4 / 9 channels screen display is available for SVR-450/940.) Button to activate Auto sequence mode. ( = Auto Sequence ) Button for playback pause. (Does not work in Live mode.) Button for saving JPEG images. Button to change to Search mode. Not available in SVR-940/450 models. Button to control audio. Works when the user logs in as 'Admin'. Button to change the PAN/ TILT mode of speed dome cameras.
Chapter 6. Web-Viewer 6.3 SEARCH mode Buttons Functions Button to change to Live mode. / / / Buttons for playback 1 minute before/after. Buttons to start and stop play. Buttons to move 1 frame back/1 frame forward. Buttons to fast-rewind/fast-forward play. ( 2 x and 4x play speeds. ) Windowtodisplaythecalendar.Dateswithrecordeddataaredisplayed incolors.Whenadateisclicked,thewindowbelowshowstimebarswith the data. Select the time to play the data.
Chapter 6. Web-Viewer 6.4 Web-Viewer buttons 1) Live Mode Not available 4/9/16 channels Auto Sequence - Auto sequence of the selected channel. Button for Search Mode 'ZF' mdoe. Button to go or return to the selected menu in the camera OSD menu. Display camera OSD menu Close camera OSD menu Buttonstoselectthespeeds for Pan/Tilt/Zoom/Focus (Max.
Chapter 6. Web-Viewer 2) Search Mode Button for Live Mode Button for OSD control over video screen.
Chapter 7. Troubleshooting The SVR-450/940 is a very sophisticated device, so failure can occur. In case of failure, please follow the instructions given below. • The unit will not turn on even after plugging in the adaptor jack. * Check whether the power cord is properly plugged in. • Images are not appearing on the monitor after plugging in the adaptor jack * Check whether the video output is BNC or VGA (Check the dip switch at the rear.
4CH/9CH Standalone Digital video recorder Specifications Spec. SVR-450 SVR-940 Video Input 4BNC 9BNC VideoOutput Monitor A 1BNC, 1VGA (Selectable) Monitor B - 1BNC, 1VGA (Selectable), S-Video 1BNC (Single/SPOT) Compression MPEG4 Speed 120fps 270fps Resolution 720 X 480, 360 X 240 720x480,720x240,360x240 Multi screen 1/4 1/4/9 Display Speed Record Resolution Mode HDD Max. 120fps 704X480, 352X240 704X480, 704X240,352X240 Normal, Schedule, Event, TEXT 160GB 1EA 250GB 1EA (Max.
COMPATIBLE SATA HDD LIST MODEL SIZE RPM BUFFER Reconition Record Playback ST31000340SV (Surveillance) 1TB 7200 RPM 16 MB OK OK OK ST3500830SCE 500 GB 7200 RPM 8 MB OK OK OK ST3250410AS (Barracuda) 250 GB 7200 RPM 16 MB OK OK OK ST3250310SV (Surveillance) 250 GB 7200 RPM 8 MB OK OK OK ST3160815AS (Barracuda) 160 GB 7200 RPM 8 MB OK OK OK HDS721010KLA330 1TB 7200 RPM 32 MB OK OK OK HDP725050GLA360 500 GB 7200 RPM 16 MB OK OK OK COMPANY Seagate HITACHI
SATA HDD INSTALLATION 1. Insert rubber rings to the bracket and screw the bracket to the HDD. 2. When assemble the SATA converter board, screw on the only upper-right corner like the picture below. Need assy Screw 3. Select "Master" or "Slave" using the Jumper switch on SATA converter board. Set the Master/Slave using the Jumper switch. In case of installing two HDDs, firstly set the Master/Slave. If One HDD is "Master", the other should be set to "Slave".
4. Connect the E-IDE & power cables. a. Direction of the SATA Converter board b. Direction of the main power Sub-power cable for SATA Converter board Connect to the power cable Connect to the E-IDE HDD cable 5. In case of installing two Hard Disk Drives. Check the "MASTER" or "SLAVE" on the SATA converter board. Connect to the power(SMPS) using power cable. (1st HDD - the main power cable, 2nd HDD - the sub power cable) When you use two HDDs, HDDs should be same model and have same interface.
COMPATIBLE PATA HDD LIST COMPANY HITACHI MAXTOR MODEL SIZE RPM BUFFER Reconition Record Playback HDS728080PLAT20 80 GB 7200 RPM 2M OK OK OK HDS721680PLAT80 80 GB 7200 RPM 8M OK OK OK HDT722516DLAT80 160 GB 7200 RPM 8M OK OK OK HDT722516DLAT80 160 GB 7200 RPM 8M OK OK OK HDS722525VLAT80 250 GB 7200 RPM 8M OK OK OK HDT722525DLAT80 250 GB 7200 RPM 8M OK OK OK HDT725025VLAT80 250 GB 7200 RPM 8M OK OK OK HDT725032VLAT80 320 GB 7200 RPM 8M OK OK OK
COMPANY Seagate MODEL SIZE RPM BUFFER Reconition Record Playback ST3400-15ACE 40 GB 7200 RPM 2M OK OK OK ST3800-12ACE 80 GB 7200 RPM 2M OK OK OK ST31200-25ACE 120 GB 7200 RPM 2M OK OK OK ST31600-22ACE 160 GB 7200 RPM 2M OK OK OK ST3300820ACE 300 GB 7200 RPM 8M OK OK OK ST3300831ACE 300 GB 7200 RPM 8M OK OK OK ST3400832ACE 400 GB 7200 RPM 8M OK OK OK ST3400820ACE 400 GB 7200 RPM 8M OK OK OK ST3500641A 500 GB 7200 RPM 16 M OK OK OK ST3750
MEMO
MEMO
MEMO
• SALES NETWORK SAMSUNG TECHWIN CO., LTD. 145-3, Sangdaewon-dong, Jungwon-gu, Seongnam-si, Gyeonggi-do, 462-120, Korea TEL : +82-31-740-8151~8158 FAX : +82-31-740-8145 SAMSUNG OPTO-ELECTRONICS UK, LTD. Samsung House, 1000 Hillswood Drive, Hillswood Business Park Chertsey, Surrey KT16 OPS TEL : +44-1932-45-5308 FAX : +44-1932-45-5325 www.samsungtechwin.com www.samsungcctv.com VAN 08.
