SyncMaster 242MP Install Drivers Install Programs
Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment. Prohibited Important to read and understand at all times Do not disassemble Disconnect the plug from the outlet Do not touch Grounding to prevent an electric shock Power When not used for an extended period of time, set your computer to DPMS. If using a screen saver, set it to the active screen mode. Do not use a damaged or loose plug. z This may cause an electric shock or fire.
Do not pull the plug out by the wire nor touch the plug with wet hands. z This may cause an electric shock or fire. Use only a properly grounded plug and receptacle. z An improper ground may cause electric shock or equipment damage. Do not excessively bend the plug and wire nor place heavy objects upon them, which could cause damage. z This may cause an electric shock or fire. Do not connect too many extension cords or plugs to an outlet. z This may cause fire.
z Dropping the product may cause damage to the product or personal injury. Set down the monitor carefully. z The monitor could be damaged or broken. Do not place the monitor face down. z The TFT-LCD surface may be damaged. Installing a wall bracket must be done by a qualified professional. z z Installation by unqualified personnel may result in injury. Always use the mounting device specified in the owner's manual.
Do not spray water or detergent directly on the monitor. z This may cause damage, electric shock or fire. Use the recommended detergent with a smooth cloth. If the connector between the plug and the pin is dusty or dirty, clean it properly with a dry cloth. z A dirty connector may cause an electric shock or fire. Contact the Service Center or Customer Center for interior cleaning once a year. z Keep the product's interior clean.
Disconnect the plug from the outlet during storms or lightening or if it is not used for a long period of time. z Failure to do so may cause an electric shock or fire. Do not try to move the monitor by pulling only the wire or the signal cable. z This may cause a breakdown, electric shock or fire due to damage to the cable. Do not move the monitor right or left by pulling only the wire or the signal cable. z This may cause a breakdown, electric shock or fire due to damage to the cable.
Adjust the resolution and frequency to the levels appropriate for the model. z Inappropriate resolution may cause undesirable picture quality. 24 inch - 1920 X 1200 Keep the volume at a proper level when you use the headphones. z Excessively loud volume levels may damage hearing. Watching the monitor continuously at a too close angle may result in eyesight damage. To ease eye strain, take at least a five-minute break after every hour of using the monitor.
z This may cause a battery to break or leak and could lead to fire, injury, or contamination (damage). The battery (and rechargeable battery) are not ordinary refuse and must be returned for recycling purposes. The customer is responsible for returning the used or rechargeable battery for recycling purposes as the consumer of the battery.
Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Contact a local dealer to buy optional items.
D-Sub Cable Power Cord Audio Cable DVI Cable Remote Control Batteries (AAA X 2) Radio Antenna Others Connector Side cover Speaker(Option) Speaker Speaker-cover Speaker-Stand Speaker Brackets Use only for the mounting type installation.
Speaker-Side cover Front 1. MENU 2. CH 3. - VOL + 4. / FM RADIO 5. SOURCE 6. PIP 7. Power button 8. Power indicator 9. Remote Control Sensor 1. MENU Use this button to open the on-screen menu and exit from the menu screen or close screen adjustment menu. 2. CH Moves from one menu item to another vertically or adjusts selected menu values. In TV mode, selects TV channels. >>Click here to see an animation clip 3. - VOL + Moves from one menu item to another horizontally or adjusts selected menu values.
See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your monitor OFF when it is not needed or when left unattended for long periods. Rear Remove the rear monitor cover before connecting to an external device. When it is connected, replace the cover. (The configuration at the back of the monitor may vary from product to product.) 1. DVI/PC IN 1. DVI cable terminal (input) 2. D-SUB(15 pin) cable terminal (input) 3.
3. EXT(RGB) External device terminal - Scart is mainly used in Europe. As for EXT(RGB) port of the Monitor, it makes TV or Video signal input and output. 4. AV IN 1. External device sound input terminal 2. External device (video) input terminal 3. External device (S-video) input terminal 4. FM radio antenna terminall 5. Headphone / R-SPEAKER-L / ANT IN 1. Headphone sound output terminal 2. Speaker sound output terminal 3. TV antenna terminal For more information > Connecting TV 6.
See Connecting the Monitor for further information regarding cable connections. Remote Control The performance of the remote control may be affected by a TV or other electronic device operated near the monitor, causing malfunction due to interference with frequency. 1. POWER 2. Number button 3. +100, -/-4. - + 5. MUTE 6. TTX/MIX 7. MENU 8. ENTER 9. FM RADIO 10. CH/P 11. SOURCE 12. INFO 13. EXIT 14. Up-Down Left-Right buttons 15. AUTO 16. P.MODE, M/B (MagicBright™) 17. P.SIZE 18. STILL 19. PIP 20. S.
2. Number button Selects TV channels in the TV mode. You may use this button in PIP mode as well. 3. +100 Press to select channels over 100. For example, to select channel 121, press "+100", then press "2" and "1". -/-- (One/Two-Digit channel selection ) Use to select a channel numbered ten or over. Press this button, and the "--" symbol is displayed. Enter the two-digit channel number. -/-- is mainly used in Europe. 4. + Adjusts the audio volume. 5. MUTE Pauses (mutes) the audio output temporarily.
18. STILL Press the button once to freeze the screen. Press it again to unfreeze. 19. PIP Push the PIP button to turn PIP screen On/Off. 20. S.MODE ( Sound Mode ) When you press this button, current mode is displayed on the lower center of the screen. The Monitor has a built-in high fidelity stereo amplifier. Then push button again to circle through available preconfigured modes. ( Standard → Music → Movie → Speech → Custom ) 21.
Connecting the Monitor Remove the rear monitor cover before connecting to an external device. When it is connected, replace the cover. 1. Connecting to a Computer 1. Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. 2-1. Using the D-sub (Analog) connector on the video card, Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor. 2-2.
5. You may enjoy clear and quality sound from the computer sound card using the monitor speakers. (You don't need to install any separate speakers for your computer.) You may get a blank screen depending on the type of video card you are using, if you connect simultaneously both the D-sub and DVI cables to one computer. If you connect properly your monitor using the DVI connector but get a blank or fuzzy screen, check to see if the monitor status is set to analogue.
1. Input devices such as DVD, VCR or Camcorder are connected to the Video or S-Video terminal of the monitor using the S-Video cable. S-Video, RCA cable and EXT(RGB) cable are optional. 2. Connect the Audio (R) and Audio (L) terminals of a DVD, VCR or Camcorders to the monitor's R and L audio input terminals using audio cables. 3. Then, start the DVD, VCR or Camcorder with a DVD disc or tape inserted. 4. Select AV or S-Video using the SOURCE button on the monitor's front. 1-2.
1. Connect the CATV or antenna coaxial cable to the Antenna terminal on the rear of the monitor. You need to use a coaxial antenna cable. When using an interior antenna terminal: Check the antenna terminal on the wall first and connect the antenna cable. When using an outdoor antenna: If you are using an outdoor antenna, use a professional for installation if possible. To connect the RF cable to the antenna input terminal: Keep the copper wire portion of the RF cable straight. 2. Turn on the monitor. 3.
1. Connect the Audio (R) and Audio (L) outputs on the DVD / DTV set top box to the Audio (R) and Audio (L) inputs on the monitor using audio cables. 2. Connect a video cable between the component( PR, PB,Y) jacks on the Monitor and the PR, PB,Y jacks on the DVD / DTV set top box. 3. Select Component using the SOURCE button on the monitor's front. 4. Connecting Headphone You may connect your Headphone to the monitor. 1. Connect your Headphone to the Headphone connection terminal. 5.
A. When installing the speaker into the mains Be sure to hold the LCD set instead of the speakers when moving the LCD set with the speakers attached. (Otherwise may damage the brackets connecting the speakers.) Detach side covers from both sides of the LCD set. z Fit the side hole of the speaker into the bracket and fix it with screws(Silver 4EA). z Detach side covers from Speakers. Fit the side hole of the speaker into the protruding connector of the bracket.
Secure the Speaker Covers by setting them into the holes located on the front side of the speakers. z Make sure the arrow inside the cover points upward z B. When separating the speaker from the mains Secure the Speaker Covers by setting them into the holes located on the front side of the speakers z Mount assembled speaker on Speaker Stand and then push the speaker to be completely secured.
2. Connect the cable in the way the rear terminal of the speaker fits into the rear R-SPEAKER-L terminal of the mains. Using the Stand This monitor supports various types of VESA-standard bases. You need to either fold or remove the base in use in order to install a VESA base. 1. Folding the base The monitor may be reclined from -5 to 15 degrees. 2. Attaching a wall-mount This monitor accepts a 200 mm x 100 mm VESA-compliant mounting interface pad.
A. Monitor B. Mounting interface pad 1. 2. 3. 4. Turn off your monitor and unplug its power cord. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen. Remove four screws and then remove the Stand from the LCD monitor. Align the Mounting Interface Pad with the holes in the Rear Cover Mounting Pad and secure it with four screws that came with the arm-type base, wall mount hanger or other base.
3 1. Insert three Hangers of the set-bracket B into the grooves of the wall-bracket A. 2. Fix set-bracket B and wall-bracket A with screws C. Before installing the set on the wall, connect the cables to the set first. Installing the Monitor Driver When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions appropriate for the operating system you have.
4. Click the "Install" button in the "Warning" window. 5. Monitor driver installation is completed. Windows XP/2000 1. Insert CD into the CD-ROM drive. 2. Click "Windows XP/2000 Driver" 3. Choose your monitor model in the model list, then click the "OK" button. 4. Choose your monitor model in the model list, then click the "OK" button. 5. If you can see following message window, then click the "Continue Anyway" button. Then click "OK" button.
This monitor driver is under certified MS logo,and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage. http://www.samsung.com/. 6. Monitor driver installation is completed. Windows XP | Windows 2000 |Windows Me |Windows NT | Linux When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another.
5. Click "Update Driver.." and select "Install from a list or.." then click "Next" button. 6. Select "Don't search ,I will.." then click "Next" and then click "Have disk". 7. Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next" button. 8. If you can see following message window, then click the "Continue Anyway" button. Then click "OK" button.
This monitor driver is under certified MS logo,and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage. http://www.samsung.com/ 9. Click the "Close" button, then click "OK" button continually. 10. Monitor driver installation is completed. Microsoft® Windows® 2000 Operating System When you can see "Digital Signature Not Found" on your monitor, follow these steps. 1. Choose "OK" button on the "Insert disk" window. 2.
Microsoft® Windows® Millennium Operating System 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Click "Start" , "Setting" , "Control Panel". Double click "Display" icon. Select the "Settings" tab and click "Advanced Properties" button. Select the "Monitor" tab. Click the "Change" button in the "Monitor Type" area. Choose "Specify the location of the driver". Choose "Display a list of all the driver in a specific location.." then click "Next" button.
One of the recent problems in using a computer is that the color of the images printed out by a printer or other images scanned by a scanner or a digital camera are not the same as those shown on the monitor. The Natural Color S/W is the very solution for this problem. It is a color administration system developed by Samsung Electronics in association with Korea Electronics & Telecommunications Research Institute (ETRI).
Input Available Mode OSD : PC / DVI : TV : AV : S-Video : Component Description Source List Use to select PC, TV or other external input source connected to the Monitor. Use to select the screen of your choice. The direct button on the remote control is 'SOURCE' button. 1) PC 2) DVI : HDCP supported 3) TV 4) Ext.- EXT(RGB) is mainly used in Europe. As for EXT(RGB) port of the Monitor, it makes TV or VIDEO signal input and output.
1) PIP : Turn the PIP Screen on or off. The direct button on the remote control is 'PIP' button. Off / On 2) Source : Select the input source for the PIP. The direct button on the remote control is 'SOURCE' button. PC / DVI : TV / Ext.(EXT(RGB) is mainly used in Europe.) / AV / S-Video / Component Mode 4) Position / , 2) Source 3) Size 3) Size : Change the Size of the PIP window. The direct button on the remote control is 'SIZE' button. / / If you select activated.
OSD Description Play MagicBright™ MagicBright™ is a new feature providing the optimum viewing environment depending on the contents of the image you are watching. Currently four different modes are available: Entertain, Internet,Text and Custom. Each mode has its own pre-configured brightness value. You can easily select one of four settings by simply pressing the 'M/B' button. The direct button on the remote control is 'M/B' button.
then use Fine again. - Available in PC Mode Only 1) Coarse : Removes noise such as vertical stripes. Coarse adjustment may move the screen image area. You may relocate it to the center using the Horizontal Control menu. 2) Fine : Removes noise such as horizontal stripes. If the noise persists even after Fine tuning, repeat it after adjusting the frequency (clock speed). 3) Position : Adjusts the screen location horizontally and vertically.
3) Movie 4) Custom Custom You can use the on-screen menus to change the contrast and brightness according to personal preference. 1) Contrast : Adjusts the Contrast. 2) Brightness : Adjusts the Brightness. 3) Sharpness : Adjusts the difference between the lightest and darkest areas of the display. 4) Color : Adjusts the Color of the PIP window on the screen. 5) Tint : Adds a natural tone to the display. MagicColor Pro Implements the natural color chroma according to the display screen.
Sound Available Mode : PC / DVI : TV : AV : S-Video OSD Description Mode The Monitor has a built-in high fidelity stereo amplifier. The direct button on the remote control is 'S.MODE' button. : Component 1) Standard : Choose Standard for the standard factory settings. 2) Music : Choose Music when watching music videos or concerts. 3) Movie : Choose Movie when viewing movies. 4) Speech : Choose Speech when watching a show that is mostly dialogue (i.e., news).
BBE and Dolby Virtual cannot be functioned at the same time. Sound Select You can select either Main or Sub when PIP is On. 1) Main 2) Sub Available : PIP ON FM Radio Press the button on the front or the "FM RADIO" button on the remote control to select the "FM RADIO" feature. The direct button on the remote control is 'FM RADIO' button. 1) Auto Store You can scan the frequency ranges available on your FM Radio in your area and store all the channels found automatically.
1) Air 2) STD 3) HRC 4) IRC 5) AFN STD, HRC, IRC, AFN, and Air identify various types of cable TV systems. Contact your local cable company to identify the type of cable system that exists in your particular area. Auto Program The TV automatically cycles through all of the available channels and stores them in memory. This takes about one to two minutes. In rare cases, "Auto program" may miss a few channels due to weak signals and the channels may not be added to the channel memory.
If country is not selected properly, the product may not locate channels. Area Configuration is not available when the V-chip feature has been set. Language You can choose one of 15 languages. The language chosen affects only the language of the OSD. It has no effect on any software running on the computer. Sleep Timer Use to set the Monitor to be turned off automatically in certain minutes.
Self-Test Feature Check Check the following items yourself before calling for service. Contact the Service Center for problems that you cannot solve by yourself. Self-Test Feature Check | Not Optimum Mode | Display Adapter Driver Maintenance and Cleaning | Symptoms & Recommended Actions 1. Self-Test Feature Check Your monitor provides a self test feature that allows you to check whether your monitor is functioning properly. 1. Turn off both your computer and the monitor. 2.
Refer to Specifications > Preset Timing Modes for the resolutions or frequencies that are supported by the monitor. 3. Display Adapter Driver Display adapter refers to the computer video card driver. If the adapter is not properly set, you cannot adjust resolution, frequency or color and you cannot install the monitor driver. 1. Checking Adapter Driver Click Start → Settings → Control Panel → Display → Settings → Advanced → Adapter.
1. Problems related to Installation Problems related to the monitor installation and their solutions are listed. Problems PC Mode TV Mode Solutions It appears the PC does not function normally. z The monitor screen flickers. z TV screen is blurred or shows noise signals. z TV signal is not received z z Check if the Display Adapter Driver (VGA Driver) is properly installed.
White color is poor. Power Indicator blinks green. z Screen is blank and power indicator light is steady green or blinks every 0.5 or 1 seconds z The screen is blank and is blinking. z z The monitor is currently saving the changes made in settings to the OSD memory. The monitor is using its power management system. Press any key on the keyboard.
How can I set the Power Saving function? z z How can I clean the outer case/LCD Panel? z z Windows XP : Set the resolution at the Control Panel→Appearance and Themes→Display→Screen Saver . Set the function at BIOSSETUP of the computer. (Refer to Windows/Computer Manual). Windows ME/2000 : Set the resolution at the Control Panel→Display→Screen Saver. Set the function at BIOS-SETUP of the computer. (Refer to Windows/Computer Manual).
General General Model Name SyncMaster 242MP LCD Panel Size 24.0" Diagonal Display area 518.4(H) x 324(V) Pixel Pitch 0.270mm (H) x 0.270mm (V) Type a-si TFT active matrix Synchronization Horizontal 31 ~ 81kHz Vertical 56 ~ 75 Hz Display Color 16.7M Colors (true 8bit) Resolution Optimum resolution WUXGA 1920 x 1200 @60Hz Maximum resolution WUXGA 1920 x 1200 @60Hz Input Signal, Terminated RGB Analog , DVI(Digital Visual Interface) Compliant Digital RGB, 0.
DVI-D to DVI-D connector, detachable, 2.0m Power Consumption Less than 150W Power Saving Less than 2W Dimensions (WxDxH)/ Weight 558.4 X 90 X 380.7 mm / 22.0 X3.5 X 15.0 inch (Without stand) 558.4 X 177 X 427.2 mm / 22.0 X 7.0 X 16.8 inch / 8.3 kg (With Stand) 558.4 X 90 X 380.7 mm / 22.0 X3.5 X 15.0 inch / 9.65 Kg (with Speaker) VESA Mounting Interface 200 mm x 100 mm (for use with Specialty(Arm) Mounting hardware.
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows. Table 1. Preset Timing Modes Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Clock (MHz) Sync Polarity (H/V) MAC, 640 x 480 35.000 66.667 30.240 -/- MAC, 832 x 624 49.726 74.551 57.
Countries Denmark Portugal Netherlands Austria Singapore Indonesia Australia North Korea Rumania Uruguay Paraguay Brazil SECAM Broadcasting Systems SECAM-B Countries South Africa Hongkong SECAM-D Iran Iraq Saudi Arabia Syria Lebanon Egypt SECAM-K1 Russia Hungary Bulgaria Poland SECAM-L France Horizontal Frequency The time to scan one line connecting the right edge to the left edge of the screen horizontally is called Horizontal Cycle and the inverse number of the Horizontal Cycle is called Hor
Service The address and phone number of the company can be changed without previous notice. AUSTRALIA : Samsung Electronics Australia Pty Ltd. Customer Response Centre 7 Parkview Drive, Homebush Bay NSW 2127 Tel : 1300 362 603 http://www.samsung.com.au/ BRAZIL : Samsung Eletronica da Amazonia Ltda. R. Prof. Manoelito de Ornellas, 303, Terro B Chacara Sto. Antonio, CEP : 04719-040 Sao Paulo, SP SAC : 0800 124 421 http://www.samsung.com.br/ CANADA : Samsung Electronics Canada Inc.
Ciencies, 55-65 (Poligono Pedrosa) 08908 Hospitalet de Llobregat (Barcelona) Tel. : (93) 261 67 00 Fax. : (93) 261 67 50 http://samsung.es/ FRANCE : SAMSUNG ELECTRONICS FRANCE Service Paris Nord 2 66 rue des Vanesses BP 50116 Villepinte 95950 Roissy CDG Cedex Tel : 08 25 08 65 65 Fax : 01 48 63 06 38 http://www.samsungservices.com/ GERMANY : TELEPLAN Rhein-Main GmbH Feldstr. 16 64331 Weiterstadt T. 06151/957-1306 F. 06151/957-1732 * EURO 0.12/Min http://www.samsung.
PERU : Servicio Integral Samsung Av.Argentina 1790 Lima1. Peru Tel: 51-1-336-8686 Fax: 51-1-336-8551 http://www.samsungperu.com/ PORTUGAL : SAMSUNG ELECTRONICA PORTUGUESA S.A. Rua Mário Dioniso, No2 - 1º Drt. 2795-140 LINDA-A-VELHA Tel. 214 148 114/100 Fax. 214 148 133/128 Free Line 800 220 120 http://www.samsung.pt/ SOUTH AFRICA : Samsung Electronics,5 Libertas Road, Somerset Office Park, Bryanston Ext 16. Po Box 70006, Bryanston,2021, South Africa Tel : 0027-11-549-1621 Fax : 0027-11-549-1629 http://www.
Terms Sync Signal Sync (Synchronized) Signals refer to the standard signals that are required to display desired colors on the monitor. They are divided into Vertical and Horizontal Sync Signals. These signals display normal color images by the set resolution and frequency. Types of Sync Signals Separate This is a scheme of transmitting individual vertical and horizontal sync signals to the monitor.
Satellite Broadcasting Broadcasting service provided via satellite. Enables high picture quality and clear sound throughout the country regardless of the location of the viewer. Sound Balance Balances the levels of the sound coming from each speaker in televisions with two speakers. Cable TV Whereas the terrestrial broadcasting is delivered via frequency signals through the air, cable broadcasting is transmitted via a cable network.
Authority Information in this document is subject to change without notice. © 2005 Samsung Electronics Co., Ltd. All rights reserved. Reproduction in any manner whatsoever without the written permission of Samsung Electronics Co., Ltd. is strictly forbidden. Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.
FCC Information | IC Compliance Notice | MPR II Compliance European Notice (Europe only) | PCT Notice | VCCI | TCO'95-Ecological requirements for personal computers (TCO'95 applied model only) TCO'99-Ecological requirements for personal computers (TCO'99 applied model only) TCO'03-Ecological requirements for personal computers (TCO'03 applied model only) TCO'03 Recycling Information (TCO'03 applied model only) Medical Requirement Mercury Statement (LCD Monitor, LCD TV, DLP Projection TV, Projector for USA o
MPR II Compliance This monitor complies with SWEDAC(MPR II) recommendations for reduced electric and magnetic fields. European Notice(Europe Only) Products with the CE marking comply with the EMC Directive(89/336/EEC), (92/31/EEC), (93/68/EEC) and the Low Voltage Directive (73/23/EEC) issued by the Commission of the European Community.
There are also other characteristics of a monitor, such as energy consumption levels, that are important from both the working and natural environment viewpoints. Since all types of conventional electricity generation have a negative effect on the environment (acidic and climate-influencing emissions, radioactive waste, etc.) it is vital to conserve energy. Electronic equipment in offices consumes an enormous amount of energy, since it is often routinely left running continuously.
electronics components concerned with the display unit. CFCs (freons) CFCs (freons) are sometimes used for washing printed circuit boards and in the manufacturing of expanded foam for packaging. CFCs break down ozone and thereby damage the ozone layer in the stratosphere, causing increased reception on Earth of ultraviolet light with consequent increased risks of skin cancer (malignant melanoma).
via the Internet, using the address: http://www.tco-info.com/ Environmental requirements Flame retardants Flame retardants are present in printed circuit boards, cables, wires, casings and housings. Their purpose is to prevent, or at least to delay the spread of fire. Up to 30% of the plastic in a computer casing can consist of flame retardant substances. Most flame retardants contain bromine or chloride, and those flame retardants are chemically related to another group of environmental toxins, PCBs.
Energy z Energy-saving mode after a certain time – beneficial both for the user and the environment z Electrical safety Emissions z z Electromagnetic fields Noise emissions Ecology The product must be prepared for recycling and the manufacturer must have a certified environmental management system such as EMAS or ISO 14 000 z Restrictions on o chlorinated and brominated flame retardants and polymers o heavy metals such as cadmium, mercury and lead.
This equipment has been tested and found to comply with the limits for medical devices to the IEC 601-1-2:1994. These limits are designed to provide reasonable protection against harmful interference in a typical medical installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to other devices in the vicinity.
PRODUCT INFORMATION (Image Retention Free) LCD Monitors and TVs may have image retention when switching from one image to another especially after displaying a stationary image for a long time. This guide is to demonstrate correct usage of LCD products in order to protect them from Image retention. What is Image retention ? During normal operation of a LCD panel, pixel image retention doesn't occur.
The best way to protect your monitor from Image retention is to set your PC or System to operate a Screen Saver program when you are not using it. Image retention may not occur when a LCD panel is operated under normal conditions. Normal conditions are defined as continuously changing video patterns. When the LCD panel is operated for a long time with a fixed pattern (-over 12 hours-), there may be slight difference in voltage between electrodes that work the liquid crystal (LC) in a pixel.
