Specifications

ManualsBrandsSamsung ManualsComputer equipment151D

MULTIFUNCTIONAL DIGITAL SYSTEMS

e-STUDIO162/162D

e-STUDIO151/151D

File No. SME04003200

R04112171700-TTEC

Ver00_2005-01

Summary of content (176 pages)

PAGE 1
MULTIFUNCTIONAL DIGITAL SYSTEMS e-STUDIO162/162D e-STUDIO151/151D File No.
PAGE 2
© 2005 TOSHIBA TEC CORPORATION All rights reserved Parts marked with “ ” are important for maintaining the safely of the machine. Be sure to replace these parts with the replacement parts specified to maintain the safety and performance of the machine.
PAGE 3
GENERAL PRECAUTIONS REGARDING THE INSTALLATION AND SERVICE FOR e-STUDIO162/162D/151/151D The installation and service should be done by a qualified service technician. 1. Transportation/Installation • When transporting/installing the machine, be sure to use the positions as indicated below. The machine is quite heavy and weighs approximately 16.8 kg (37 lb.), therefore pay full attention when handling it.
PAGE 4
3. Main Service Parts for Safety • The breaker, door switch, fuse, thermostat, thermofuse, thermistor, etc. are particularly important for safety. Be sure to handle/install them properly. If these parts are shorted circuit and/or made their functions out, they may burn down, for instance, and may result in fatal accidents. Do not allow a short circuit to occur. Do not use the parts not recommended by Toshiba TEC Corporation. 4.
PAGE 5
00_COVER.fm 2 ページ２００４年１２月３日金曜日午後４時１分 CAUTION This product is a class 1 laser product that complies with 21CFR 1040 of the CDRH standard and IEC825. This means that this machine does not produce hazardous laser radiation. The use of controls, adjustments or performance of procedures other than those specified herein may result in hazardous radiation exposure.
PAGE 6
00_COVER.fm 3 ページ２００４年１２月１６日木曜日午後１時４５分 At the production line, the output power of the scanner unit is adjusted to 0.57 MILLI-WATT PLUS 20 PCTS and is maintained constant by the operation of the Automatic Power Control (APC). Even if the APC circuit fails in operation for some reason, the maximum output power will only be 15 MILLI-WATT 0.1 MICRO-SEC. Giving and accessible emission level of 42 MICRO-WATT which is still-less than the limit of CLASS-1 laser product.
PAGE 7
e-STUDIO162_151.book 1 ページ２００４年１２月２日木曜日午後９時３７分 CONTENTS [1] GENERAL 1. Major functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 2. Note for servicing and handling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1-1 5. [2] SPECIFICATIONS 1. 2. 3. 4. 5. Basic Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Operation specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PAGE 8
01_GENER.fm 1 ページ２００５年１月３１日月曜日午後２時５分 [1] GENERAL 1. Major functions Configurations Item CPM / PPM Model A4 e-STUDIO162 16 e-STUDIO151 15 e-STUDIO162D 16 e-STUDIO151D 15 Color SB/ 2 GDI ADF R-ADF Scanner SPLC E-SORT Duplex Shifter FAX MB Tray printer (push) MB Opt Opt Opt ❍ ✕ ❍ ❍ ✕ ❍ Opt MB Opt Opt ❍ Opt ✕ ❍ ❍ ❍ ❍ Opt DDM IEEE External USB RJ45 1284 NIC ❍ ❍ ❍ ❍ ❍ (2.0) ❍ (2.
PAGE 9
02_SPECI.fm 1 ページ２００４年１２月２２日水曜日午後１時１０分 [2] SPECIFICATIONS 1. Basic Specifications Item Type Copy system Segment (class) Copier dimensions Weight (Approximately) Desktop Dry, electrostatic Digital personal copier 20.4"(W) x 19.8"(D) x 11.7"(H) (518mm(W) x 503mm(D) x 296mm(H)) e-STUDIO162/151 Approx. 36.6lbs. (16.6kg) e-STUDIO162D/151D Approx. 37.1lbs. (16.8kg) 2.
PAGE 10
02_SPECI.fm 2 ページ２００４年１２月２２日水曜日午後３時３７分 Section, item Fusing system Upper heat roller Lower heat roller Heater lamp Fusing section Electrical section Power source Power consumption Details type type type Voltage Power consumption Voltage Frequency Rated current Max.
PAGE 11
02_SPECI.fm 3 ページ２００４年１２月２２日水曜日午後１時１０分 4. SPLC printer Print speed First print time Duplex ROPM CPU Memory Interface Network Emulation MIB support Resolution Supported OS WHQL support Application Max. 15ppm (A4 / with ROPM) / 16ppm (Letter / with ROPM) 9.6 sec. (without data transfer time) Yes (e-STUDIO162D/151D) Yes None Share the memory with E-SORT function IEEE1284 / USB 2.0 External NIC (Optional) SPLC (JBIG GDI) Yes (with GA-1170) 600dpi *1 Win 95 / 98 / Me / NT 4.
PAGE 12
03_CONSU.fm 1 ページ２００４年１２月２２日水曜日午後１時３６分 [3] CONSUMABLE PARTS 1. Supply list A. Europe/SCA/SCNZ No. Item 1 Toner CA (Black) 2 Developer 3 Drum kit Content Toner (Toner: Net Weight 243g) Polyethylene bag Developer (Developer: Net Weight 170g) Drum Drum fixing plate × 10 × 10 ×1 ×1 ×1 Life Product name 8K PS-ZT1200 × 10PLS Package 1 25K D-1200 1 25K OD-1200 10 Remark ∗ Life setup is based on A4 6%. Note: Printing of the master/individual cartons is made in 2 languages, English/French.
PAGE 13
03_CONSU.fm 2 ページ２００４年１２月２２日水曜日午後３時３８分 The label on the drum cartridge shows the date of production. Sub lot Production day Production month End digit of year Production place Production month Production day Destination code (Dealer, distributor, OEM, etc.) Production place 4. Toner cartridge replacement End digit of year Version No. 1) Open the front and side cabinets of the copier. 2) Keep holding Toner lever, and 3) Carefully pull out Toner unit from the copier.
PAGE 14
e-STUDIO162_151.book 1 ページ２００４年１２月２日木曜日午後９時３７分 [4] EXTERNAL VIEWS AND INTERNAL STRUCTURES 1.
PAGE 15
04_EXTER.fm 2 ページ２００４年１２月２２日水曜日午後１時４１分 3. Operation panel (e-STUDIO151/151D (Europe)) 1 2 3 4 5 OK MENU Display 1,2,3, 1,2,3, SP. FUNC 6 7 8 9 10 11 12 13 14 ZOOM READY TO COPY. 100% A4 15 16 17 18 19 0 20 21 (e-STUDIO162/162D) 1 2 3 4 5 Display READY TO COPY. 100% 8.5x11 18 6 7 1 8 9 10 11 12 13 14 15 20 21 16 17 [MODE SELECT] key / Mode indicators Press this key to select the mode.
PAGE 16
e-STUDIO162_151.book 3 ページ２００４年１２月２日木曜日午後９時３７分 4. Motors and solenoids (With optional ADF/RADF installed) 9 12 2 8 11 10 4 1 5 13 6 7 3 No.
PAGE 17
04_EXTER.fm 4 ページ２００４年１２月２２日水曜日午後１時４１分 5. Sensors and switches (With optional ADF/RADF installed) 1 2 7 8 3 4 9 5 6 No.
PAGE 18
e-STUDIO162_151.book 5 ページ２００４年１２月２日木曜日午後９時３７分 6. PWB unit (With optional ADF/RADF and FAX installed) 5 2 1 10 8 6 9 4 7 3 No.
PAGE 19
e-STUDIO162_151.book 6 ページ２００４年１２月２日木曜日午後９時３７分 7. Cross sectional view (With optional RADF installed) 3 1 2 5 18 15 16 17 4 6 7 8 9 10 14 No.
PAGE 20
05_UNPAC.fm 1 ページ２００４年１２月３日金曜日午前１１時２９分 [5] UNPACKING AND INSTALLATION 2. Cautions on handling 1. Copier installation Be careful in handling the copier as follows to maintain the performance of this copier. Improper installation may damage the copier. Please note the following during initial installation and whenever the copier is moved. Do not drop the copier, subject it to shock or strike it against any object.
PAGE 21
e-STUDIO162_151.book 2 ページ２００４年１２月２日木曜日午後９時３７分 4. Unpacking Be sure to hold the handles on both sides of the machine to unpack the machine and carry it to the installation location. 4) Remove the CAUTION tape from the front cover and remove the two protective pins from the fusing machine by pulling the strings upward one at a time. Protective pins CAUTION tape 6. Developer unit installation 5.
PAGE 22
e-STUDIO162_151.book 3 ページ２００４年１２月２日木曜日午後９時３７分 9) Shake the aluminum bag to stir developer 10) Supply developer from the aluminum bag to the top of the MX roller evenly. 7. Toner cartridge installation 1) To prevent against uneven distribution of toner, hold Toner unit with both hands and shake it several times horizontally. 2) Hold the section of Toner unit shown in the figure below, remove the packing tape, and remove the cushion. 3) Pull out the cushion in the arrow direction.
PAGE 23
e-STUDIO162_151.book 4 ページ２００４年１２月２日木曜日午後９時３７分 8. Loading the paper tray Note: Make sure that the paper is not torn, is free of dust, and has no wrinkles or curled edges. 1) Raise the handle of the paper tray and pull the paper tray out until it stops. 2) Remove the pressure plate lock. Rotate the pressure plate lock in the direction of the arrow to remove it while pressing down on the pressure plate of the paper tray. 3) Store the pressure plate lock which has been removed in step 2.
PAGE 24
e-STUDIO162_151.book 5 ページ２００４年１２月２日木曜日午後９時３７分 A. Before Installation B. Installing the software (1) Hardware and software requirements Note: • If you need to use a different connection method after installing the software based on a USB or parallel connection, you must first uninstall the software and then install it using the new connection method. • In the following explanations it is assumed that the mouse is configured for right hand operation.
PAGE 25
e-STUDIO162_151.book 6 ページ２００４年１２月２日木曜日午後９時３７分 8) When the "Finish" screen appears, click the "Close" button. A message will appear instructing you to connect the machine to your computer. Click the "OK" button. Caution: If you are running Windows 2000/XP and a warning message appears regarding the Windows logo test or digital signature, be sure to click "Continue Anyway" or "Yes". Note: After the installation, a message prompting you to restart your computer may appear.
PAGE 26
e-STUDIO162_151.book 7 ページ２００４年１２月２日木曜日午後９時３７分 11) You will return to the window of step 8). If you wish to install Button Manager or Desktop Document Manager, click the "Utility Software" button. If you do not wish to install the Utility Software, click the "Close" button and go to step 14). Note: After the installation, a message prompting you to restart your computer may appear. In this case, click the "Yes" button to restart your computer.
PAGE 27
e-STUDIO162_151.book 8 ページ２００４年１２月２日木曜日午後９時３７分 5) When you are asked how the printer is connected, select "Connected to this computer" and click the "Next" button. (3) Windows 95/98/Me/NT 4.0/2000 (Parallel) 1) The parallel cable must not be connected to the machine. Make sure that the cable is not connected before proceeding. If the cable is connected, a Plug and Play window will appear. If this happens, click the "Cancel" button to close the window and disconnect the cable.
PAGE 28
e-STUDIO162_151.book 9 ページ２００４年１２月２日木曜日午後９時３７分 7) Select the printer port and whether the machine is to be used as the default printer, make the selections and click the "Next" button. Select "LPT1" for the printer port. Note: • If "LPT1" does not appear, another printer or peripheral device is using LPT1. In this case continue the installation, and after the installation is finished, change the port setting so that the machine can use LPT1.
PAGE 29
e-STUDIO162_151.book 10 ページ２００４年１２月２日木曜日午後９時３７分 6) Select the network printer that is shared and click the "OK" button. Ask your network administrator for the server name and printer name of the machine on the network. 4) Select "SC1:" from the "Select an event" pull-down menu. 7) In the printer port selection window, verify the network printer that is shared and whether the machine is to be used as the default printer, make the selections and click the "Next" button.
PAGE 30
e-STUDIO162_151.book 11 ページ２００４年１２月２日木曜日午後９時３７分 5) Select "SC1:" from the "Scanner events" pull-down menu. D. Connecting the machine to your computer (1) Connecting a USB cable 6) Select "TOSHIBA Button Manager E" in "Send to this application". Note: If other applications are shown, deselect the checkboxes for the other applications and leave only the Button Manager checkbox selected. 7) Click the "Apply" button. 8) Repeat Steps 5) through 7) to link Button Manager to "SC2:" through "SC6:".
PAGE 31
e-STUDIO162_151.book 12 ページ２００４年１２月２日木曜日午後９時３７分 11. Interface A. USB Connector 4-pin ACON UBR23-4K2200 Type-B connector Cable Shielded twisted pair cable (2 m (6 feet) Max.: high-speed transmission equivalent) Pin configuration The pin numbers and signal names are listed in the following table. Pin No. 1 2 3 4 2 Signal name +5V -DATA +DATA GND 1 Pin No.
PAGE 32
e-STUDIO162_151.book 1 ページ２００４年１２月２日木曜日午後９時３７分 [6] COPY PROCESS An OPC drum is used for the photoconductor. (Structure of the OPC drum layers) OPC layer (20 microns thick) Pigment layer (0.2 to 0.3 microns thick) Aluminum drum 1.
PAGE 33
e-STUDIO162_151.book 2 ページ２００４年１２月２日木曜日午後９時３７分 2. Outline of print process Step-2: Exposure (laser beam, lens) This printer is a non-impact printer that uses a semiconductor laser and electrostatic print process. This printer uses an OPC (Organic Photo Conductor) for its photoconductive material. First, voltage from the main corona unit charges the drum surface and a latent image is formed on the drum surface using a laser beam.
PAGE 34
e-STUDIO162_151.book 3 ページ２００４年１２月２日木曜日午後９時３７分 Step-3: Developing (DC bias) Step-4: Transfer A bias potential is applied to the MG roller in the two component magnetic brush developing method, and the toner is charged negative through friction with the carrier. Non-image area of the drum surface charged with negative potential repel the toner, whereas the laser exposed portions where no negative charges exist, attract the toner. As a result, a visible image appears on the drum surface.
PAGE 35
e-STUDIO162_151.book 4 ページ２００４年１２月２日木曜日午後９時３７分 Step-7: Optical discharge (Semiconductor laser) Start Before the drum rotation is stopped, the semiconductor laser is radiated onto the drum to reduce the electrical resistance in the OPC layer and eliminate residual charge, providing a uniform state to the drum surface for the next page to be printed. When the electrical resistance is reduced, positive charges on the aluminum layer are moved and neutralized with negative charges on the OPC layer.
PAGE 36
e-STUDIO162_151.book 1 ページ２００４年１２月２日木曜日午後９時３７分 [7] OPERATIONAL DESCRIPTIONS 1. Outline of operation The outline of operation is described referring to the basic configuration. (Basic configuration) (Option) Operation section FAX FAX modem Scanner section (Option) CCD Network Network Box FAX I/F USB Printer/ Scanner I/F MCU (Main control/image process section) PC USB or parallel Note: The scanner function is effective only by USB connection. Network is for print only.
PAGE 37
e-STUDIO162_151.book 2 ページ２００４年１２月２日木曜日午後９時３７分 2. Scanner section A. Scanner unit The scanner unit in the digital copier scans images. It is composed of the optical unit and the drive unit. The optical unit performs scanning in the main scan direction with the light receiving elements (color CCD). The drive unit performs scanning in the sub scanning direction by moving the optical unit. B. Optical system Two white lamps are used as the light source.
PAGE 38
e-STUDIO162_151.book 3 ページ２００４年１２月２日木曜日午後９時３７分 3. Laser unit B. Laser beam path The image data sent from the MCU (image process circuit) is sent to the LSU (laser unit), where it is converted into laser beams. A. Basic structure The LSU unit is the writing section of the digital optical system. The semiconductor laser is used as the light source, and images are formed on the OPC drum by the polygon mirror and fθ lens, etc.
PAGE 39
e-STUDIO162_151.book 4 ページ２００４年１２月２日木曜日午後９時３７分 A. General description General block diagram (cross section) Thermal fuse Separator pawl PPD2 Thermistor Pressure roller 2) The surface temperature of the upper heat roller is set to 165 190°C. The surface temperature during the power save mode is set to 100°C. 3) The self-check function comes active when one of the following malfunctions occurs, and an "H" is displayed on the multicopy window. a.
PAGE 40
e-STUDIO162_151.book 5 ページ２００４年１２月２日木曜日午後９時３７分 (1) Cassette paper feed operation 1) The figure below shows the positions of the pick-up roller, the paper feed clutch sleeve, and the paper feed latch in the initial state without pressing the COPY button after lighting the ready lamp. The paper feed latch is in contact with the projection of the clutch sleeve. 2) When the COPY button is pressed, the main drive motor starts rotating to drive each drive gear.
PAGE 41
e-STUDIO162_151.book 6 ページ２００４年１２月２日木曜日午後９時３７分 (2) Manual multi paper feed operation 1) Before paper feed operation, the manual paper feed solenoid (MPFS) is turned OFF as shown in the figure below. C 3) When pawl C of the manual paper feed clutch sleeve is engaged with the manual feed latch, the manual feed stopper falls and the manual take-up roller rises. At that time, the manual paper feed roller is rotating.
PAGE 42
e-STUDIO162_151.book 7 ページ２００４年１２月２日木曜日午後９時３７分 (3) Conditions of occurrence of paper misfeed a. When the power is turned on: PPD or POD is ON when the power is turned on. b. Copy operation a PPD1 jam b PPD2 jam c POD jam PPD1 does not turn off within 4 sec after turning on the resist roller. PPD2 is off immediately after turning on the resist roller. PPD2 does not turn off within 1.2 sec after turning off the resist roller. POD does not turn on within 2.9 sec after turning on the resist roller.
PAGE 43
e-STUDIO162_151.book 8 ページ２００４年１２月２日木曜日午後９時３７分 7. Shifter Shift width: 2.5cm The offset function by the shifter is turned ON/OFF by the user program. According to the setting, offset operation is performed for every job. (Default: ON) Switchback operation is made after back copying in order to discharge documents according to the setting. Set document Documents after discharge, 1 4 3 with empty feed without empty feed 2 3 4 3 2 1 4 1 2 There are following job modes as well as D-D mode.
PAGE 44
e-STUDIO162_151.book 1 ページ２００４年１２月２日木曜日午後９時３７分 [8] DISASSEMBLY AND ASSEMBLY 2) Remove the drum fixing plate and the photoconductor drum. (Note) Dispose the drum fixing plate which was removed. Before disassembly, be sure to disconnect the power cord for safety. 1. Do not disconnect or connect the connector and the harness during the machine is powered. Especially be careful not to disconnect or connect the harness between the MCU PWB and the LSU (MCU PWB: CN20) during the machine is powered.
PAGE 45
e-STUDIO162_151.book 2 ページ２００４年１２月２日木曜日午後９時３７分 5) Remove the cleaning blade. Note: Dispose the cleaning blade which was removed. 6) Clean the cleaning section and the waste toner pipe to remove waste toner completely with a vacuum cleaner. 7) Remove the felt and duplex tape completely. Note: Be careful not to scratch or bend the sub blade. 8) Attach the cleaning blade. Securely insert the plate section of the cleaning blade into the unit and fix it with a screw.
PAGE 46
e-STUDIO162_151.book 3 ページ２００４年１２月２日木曜日午後９時３７分 12) Attach the detection gear. Note: • The detection gear is not installed to the drum cartridge packed with the main body. Add a new one. 2) Push up the lock pawls (2 positions) of the side cover, and remove the transfer charger. Lock pawl rear 1) 13) Attach the drum cover. Note: After attaching the drum cover, do not make a copy.
PAGE 47
e-STUDIO162_151.book 4 ページ２００４年１２月２日木曜日午後９時３７分 2) Set the charger cleaner to the transfer unit, and move it reciprocally a few times in the direction of the arrow shown in the figure below. A. List No. Part name Ref. 1 Operation panel unit 2 Operation PWB 4) 3) 2. Operation panel section B. Disassembly procedure 1) Open the side door, and Open the front cover. 2) 1) 1) 2) 2) Remove the screws (4 pcs.), the harness, and the operation panel unit. F.
PAGE 48
e-STUDIO162_151.book 5 ページ２００４年１２月２日木曜日午後９時３７分 2) Remove the four screws, remove the operation unit, and disconnect the connector. 3) Remove the right cabinet. 4) Remove the left cabinet. 5) Remove the screw, and remove the rear cover. 6) Remove the table glass. 3) Remove four screws, and remove the operation cabinet. 4) Remove four screws, and remove the operation PWB.
PAGE 49
08_DISSASEMBLY.fm 6 ページ２００４年１２月２３日木曜日午後１時８分 10) Remove the screw, and remove the rod stopper. 11) Remove the rod. 3) C. Assembly procedure CCD core 1) Pass the core through the CCD-MCU harness. 2) Insert the CCD-MCU harness into the CCD PWB connector of the carriage unit. 3) Move the core which was passed through the CCD-MCU harness near the CCD PWB connector as shown in the figure below, and fix it with a filament tape (19mm wide, 40mm long).
PAGE 50
e-STUDIO162_151.book 7 ページ２００４年１２月２日木曜日午後９時３７分 4. Fusing section 4) Remove the screw and remove the U-turn guide. A. List No. 1 2 3 4 5 1) Part name Ref. Thermistor PPD2 sensor Heater lamp Pressure roller Heat roller 2) B. Disassembly procedure 1) Remove the connectors (3 pcs.) of the rear cabinet. 2) Open the side cover, remove two screws, and remove the fusing unit.
PAGE 51
e-STUDIO162_151.book 8 ページ２００４年１２月２日木曜日午後９時３７分 7) Remove the plate spring on the right and remove the heater lamp. 10) Remove the pressure release levers on the right and the left sides. 1) 1) 1) 2) 11) Remove the pressure roller, the pressure bearing, and the spring. Note: Apply grease to the sections specified with an asterisk (*). Grease: “JFE552” UKOG-0235FCZZ Heater lamp Pressure roller 8) Remove the spring and remove the separation pawls (3 pcs.).
PAGE 52
e-STUDIO162_151.book 9 ページ２００４年１２月２日木曜日午後９時３７分 6) Remove the C-ring and the fusing bearing, and remove the heat roller. 5. Tray paper feed/transport section A. List 1) 2) 3) No. 1 2 3 4 5 Heat roller Part name Ref. Paper holding arm PPD1 sensor PWB LSU unit Intermediate frame unit Paper feed roller B. Disassembly procedure 1) Remove the paper holding arm. Remove the arm holder from the main unit, and remove the holder from the arm. 1) 7) Remove the parts from the heat roller.
PAGE 53
08_DISSASEMBLY.fm 10 ページ２００４年１２月２３日木曜日午後１時４４分 5) Disconnect the connector from the MCU PWB. 6) Disengage the pawls (2 positions), and remove the sensor PWB. 9) Disengage the pawl, and remove the roller knob. 10) Disengage the pawl, and shift the pulley and the bearing. 3) 2) 3) 1) 4) 2) 11) Remove the paper exit roller, and remove the belt, the pulley, and the bearing. 1) 2) 1) 7) Remove the screw, and open the upper paper guide.
PAGE 54
08_DISSASEMBLY.fm 11 ページ２００４年１２月２３日木曜日午後１時８分 13) Remove the flat cable and the grounding wire. 14) Remove the four screws, and remove the FAX PWB unit. (When the GD-1190 is installed) 18) Remove the three screws, and remove the DUP motor unit and the belt. 2) 3) 3) 1) 1) 3) 2) 1) 19) Remove the harness guide. 4) 3) 3) Caution: Be careful not to touch the sharp edge on the circumference of the metal frame the interface. 15) Disconnect the connectors.
PAGE 55
e-STUDIO162_151.book 12 ページ２００４年１２月２日木曜日午後９時３７分 21) Remove the parts as shown below, and remove the pressure release solenoid and the paper feed solenoid. 23) Remove two screws and remove the fusing connector. 24) Remove five screws and the connector, and lift the intermediate frame unit to remove. 3) 3) 3) 3) 3) 4) 4) 2) 1) 2) 1) 4) 2) 2) 3) 1) 25) Remove the four screws, and remove the lower paper guide unit.
PAGE 56
e-STUDIO162_151.book 13 ページ２００４年１２月２日木曜日午後９時３７分 31) Remove the four screws, and remove the LSU. 26) Disengage the pawl, and remove the pulley. 27) Shift and remove the shifter unit. 1) 1) 1) 3) 2) 4) 2) 3) 1) 28) Remove the screw, and remove the grounding plate and the gear. 29) Remove the E-ring, the gear, and the bearing, and remove the shifter roller. 1) Note: When assembling, turn it to the right and attach.
PAGE 57
e-STUDIO162_151.book 14 ページ２００４年１２月２日木曜日午後９時３７分 32) Remove the screw and the E-ring, and remove the PS semi-circular earth plate and the PS roller unit. 33) Remove the E-ring and remove the spring clutch from the PS roller unit. 36) Remove two E-rings and remove the paper feed roller. 37) Remove three E-rings and remove the clutch unit. Back 5) 5) Clutch unit 4) 4) Paper feed roller PS roller unit Use grease of Floil FG40H only to apply to this section.
PAGE 58
e-STUDIO162_151.book 15 ページ２００４年１２月２日木曜日午後９時３７分 6. Manual paper feed section A. List No. 1 2 3 4 3) Remove three screws and remove the multi paper feed upper frame. 1) Part name Ref. Manual transport roller Cassette detection switch PPD1 sensor PWB Side door detection unit 1) B. Disassembly procedure Multi unit 1) Remove the screw and remove the multi upper cover. 1) 2) 2) 4) Remove two screws and remove the multi feed bracket unit from the multi paper feed upper frame.
PAGE 59
e-STUDIO162_151.book 16 ページ２００４年１２月２日木曜日午後９時３７分 5) Remove three E-rings and remove the manual paper feed roller B9. 7) Cut the binding band and remove the multi paper feed solenoid. 1) 1) 1) 1) 3) 2) Multi paper feed solenoid 3) 2) L O CK T O K 6) Remove the pick-up roller. C. Assembly procedure For assembly, reverse the disassembly procedure. D. Pressure plate holder attachment 1) 1) Attach the pressure plate holder so that the resin section is not covered with the seal M1-N.
PAGE 60
e-STUDIO162_151.book 17 ページ２００４年１２月２日木曜日午後９時３７分 7. Rear frame section 7) Remove two screws and one connector, and remove the exhaust fan motor. Note: Be careful of the installing directions of the fan. Attach it so that the blowing direction faces outside. A. List No. 1 2 3 4 5 Part name Ref. FAX PWB (When the GD-1190 installed) Mirror motor Main motor Exhaust fan motor Main PWB 1) B. Disassembly procedure 1) Remove the rear cabinet.
PAGE 61
08_DISSASEMBLY.fm 18 ページ２００４年１２月２３日木曜日午後１時８分 8. Power section C. Assembly procedure For assembly, reverse the disassembly procedure. A. List 10. Reverse roller section (Duplex model only) No. Part name Ref. 1 Power PWB A. List B. Disassembly procedure 1) Disconnect each connector. 2) Remove the screw, and remove the earth line. 3) Remove two screws, and remove the power PWB unit. No. Part name Ref. 1 Reverse roller B.
PAGE 62
e-STUDIO162_151.book 1 ページ２００４年１２月２日木曜日午後９時３７分 [9] ADJUSTMENTS 5) Calculate the main scanning direction magnification ratio. Main scanning direction magnification ratio Copy image dimensions = X 100 (%) Original dimension 1. Optical section A. Copy magnification ratio adjustment The copy magnification ratio must be adjusted in the main scanning direction and in the sub scanning direction. To adjust, use TC 48-01. (When a 100mm scale is used as the original.
PAGE 63
e-STUDIO162_151.book 2 ページ 2) 3) 4) 5) ２００４年１２月２日木曜日午後９時３７分 Set the copy magnification ratio to 100%. Make a copy on A4 or 81/2" x 11" paper. Measure the length of the copied scale image. Calculate the sub scanning direction copy magnification ratio using the formula below.
PAGE 64
e-STUDIO162_151.book 3 ページ２００４年１２月２日木曜日午後９時３７分 (Example) Document guide Distance from the paper lead edge to the image lead edge, H = 5mm Image loss, R = 4mm 5mm 10mm (2) Image rear edge void amount adjustment 1) Set a scale to the rear edge section of A4 or 11" x 8 1/2" paper size as shown in the figure below, and cover it with B4 or 8 1/2" x 14" paper. 2) Execute TC 50-10 to select the print center offset (cassette paper feed) adjustment mode.
PAGE 65
09_ADJUS.fm 4 ページ２００４年１２月２２日水曜日午後２時３９分 C. Necessary tool for copy density adjustment (2) Perform the adjustment in each mode. • One of the following test charts: KODAK GRAY SCALE • B4 (14" x 8 1/2") white paper • The user program AE setting should be "3." 1) Execute TC 46-01 (300dpi). To adjust in 600dpi, execute TC 4602. 2) Select the mode to be adjusted with the exposure mode select key. Set the exposure level to 3 (center) for all adjustment. (Except for the auto mode.
PAGE 66
09_ADJUS.fm 5 ページ２００４年１２月２３日木曜日午後２時２分 3. High voltage adjustment 4. Duplex adjustment (With optional RADF installed) A. Main charger (Grid bias) Note: • Use a digital multi meter with internal resistance of 10MΩ or more measurement. • After adjusting the grid LOW output, adjust the HIGH output. Do not reverse the sequence. Procedures 1) Set the digital multi meter range to DC700V.
PAGE 67
e-STUDIO162_151.book 6 ページ２００４年１２月２日木曜日午後９時３７分 2) Set the test chart on the document glass as shown below. Document guide The trailing edge has a scale 2nd printing surface where scale is printed (lower side) B. Adjusting trailing edge void in duplex copy mode This is the adjustment of the first surface printing mode (rear end void) in duplex copying. In a duplex copying operation, the paper is delivered starting from the rear end of the first printing surface.
PAGE 68
09_ADJUS.fm 7 ページ２００４年１２月２２日水曜日午後３時３９分 5. ADF (RADF) scan position automatic adjustment (With optional ADF/RADF installed) 6. RADF (ADF) mode sub scanning direction magnification ratio adjustment (With optional ADF/RADF installed) Place a black chart so that it covers the ADF scan glass and the OC glass together, and close the OC cover. When test command 53-08 is executed, the current adjustment value is displayed as the initial display. * Default is 1. Adjustment range is 1 – 99.
PAGE 69
09_ADJUS.fm 8 ページ２００４年１２月２２日水曜日午後１時４５分 7. Automatic black level correction a. Cases when the adjustment is required 1) 2) 3) 4) When the main PWB is replaced. When the EEPROM in the main PWB is replaced. When "U2" trouble occurs. When repairing or replacing the optical section. b. Adjustment procedure Used to acquire the black level target value used for the black level adjustment of white balance.
PAGE 70
10_TESTCOMMAND.fm 1 ページ２００４年１２月２２日水曜日午後１時４７分 [10] TEST COMMAND, TROUBLE CODES 1. Entering the test command mode To enter the serviceman test command mode, press the keys as follows: [#] key → [*] key → [C] key → [*] key To cancel the test command mode, press the [CA] key. 2.
PAGE 71
e-STUDIO162_151.book 2 ページ２００４年１２月２日木曜日午後９時３７分 Main Sub Contents code code 24 01 JAM total counter clear (JAM TTL CLR.) 04 ADF counter clear (ADF CLR.) (Disabled when set to OC) (Executable only when the ADF is installed.) 05 Duplex counter clear (DPLX CLR.) (Enabled when Duplex setting is ON) 06 Developer counter clear (DVLP CLR.) 07 Drum counter clear (DRUM CLR.) 08 Copy counter clear (COPIES CLR.) 09 Printer counter clear (PRT.CLR.) 10 FAX counter clear (FAX CLR.
PAGE 72
e-STUDIO162_151.book 3 ページ２００４年１２月２日木曜日午後９時３７分 Main Sub Contents code code 66 34 Communication time measurement (Executable only when the FAX is installed.) 37 Speaker sound volume setting (Executable only when the FAX is installed.) 38 Time setting/check (Executable only when the FAX is installed.) 41 CI signal check (Executable only when the FAX is installed.) 4.
PAGE 73
e-STUDIO162_151.book 4 ページ Main code 2 Sub code 02 ２００４年１２月２日木曜日午後９時３７分 Contents Details of function/operation ADF sensor status display (ADF SENSOR) (Disabled when set to OC) (Executable only when the ADF is installed.) [Function] The ON/OFF status of the ADF sensors can be checked with the LCD. When a sensor is ON, the sensor name is displayed on the LCD.
PAGE 74
e-STUDIO162_151.book 5 ページ Main code 5 Sub code 01 ２００４年１２月２日木曜日午後９時３７分 Contents Details of function/operation Operation panel display check (LCD/LED CHK) [Function] When [OK (ENTER)/START] key is pressed, all the LCD's on the operation panel are turned ON (all pixels ON). After 5sec of ON, the machine goes into the sub code entry standby mode.
PAGE 75
e-STUDIO162_151.book 6 ページ Main code 6 Sub code 01 ２００４年１２月２日木曜日午後９時３７分 Contents Details of function/operation Paper feed solenoid (CPFS1, CPFS2, MPFS) operation check (PSOL CHK) [Function] When [OK (ENTER)/START] key is pressed, the selected paper feed solenoid repeats ON for 500ms and OF for 500ms 20times. When [←/→/10KEY] is pressed, the paper feed solenoid setting is switched. Code number 0 1 2 Setting CPFS1 CPFS2 MPFS Remark Operation is possible only when No. 2 cassette is installed.
PAGE 76
e-STUDIO162_151.book 7 ページ Main code 8 Sub code 01 ２００４年１２月２日木曜日午後９時３７分 Contents Details of function/operation Developing bias output (DVLP BIAS SET.) [Function] When [OK (ENTER)/START] key is pressed, the developing bias signal is turned ON for 30sec. When, however, an actual output value is measured, use test command 25-01. After completion of this process, the machine goes into the sub code entry standby mode. [Operation] 1) Initial display 08-01 DVLP BIAS SET. EXECUTING...
PAGE 77
e-STUDIO162_151.book 8 ページ Main code 10 Sub code 00 ２００４年１２月２日木曜日午後９時３７分 Contents Details of function/operation Toner motor operation (TONER MOTOR) [Function] When [OK (ENTER)/START] key is pressed, the toner motor is rotated for 30sec. After completion of this process, the machine goes into the main code entry standby mode. [Operation] 1) Initial display 10-00 TONER MOTOR EXECUTING... 14 00 Cancel of trouble other than U2 (TRBL CANC.) [Function] Used to cancel troubles other than U2.
PAGE 78
e-STUDIO162_151.book 9 ページ Main code 22 Sub code 02 ２００４年１２月２日木曜日午後９時３７分 Contents Details of function/operation Maintenance preset display (M-CNT PRESET) [Function] The quantity (25,000 sheets, etc.) corresponding to the code set with TC21-01 is displayed. [Operation] 1) Initial display 22-02 M-CNT PRESET ***,*** 04 JAM total counter display (JAM TTL CNT) [Function] The JAM total counter is displayed.
PAGE 79
10_TESTCOMMAND.fm 10 ページ Main code 22 Sub code 14 ２００４年１２月２２日水曜日午後１時４９分 Contents Details of function/operation ROM version display (ROM VER.) [Function] The P-ROM version is displayed. Press [←/→/10KEY] to switch the display version. Code number 0 1 2 Version Main unit Program F-IMC Program LCD DATA Display item MAIN PROG. F-IMC PROG. LCD DATA [Operation] 1) Initial display 22-14 ROM VER. MAIN PROG. 00.00 2) [→/10KEY] 22-14 ROM VER. F-IMC PROG. 00.00 2) [←/10KEY] 22-14 ROM VER. LCD DATA 00.
PAGE 80
e-STUDIO162_151.book 11 ページ Main code 22 Sub code 21 ２００４年１２月２日木曜日午後９時３７分 Contents Details of function/operation Scanner counter display (SCAN CNT) [Function] The scanner counter is displayed. [Operation] 1) Initial display 22-21 SCAN CNT ***,*** 22 ADF JAM counter display (S JAM CNT) (Disabled when set to OC) (Executable only when the ADF is installed.) [Function] The ADF JAM counter is displayed.
PAGE 81
e-STUDIO162_151.book 12 ページ Main code 24 Sub code 09 ２００４年１２月２日木曜日午後９時３７分 Contents Details of function/operation Printer counter clear (PRT.CLR.) [Function] When [OK (ENTER)/START] key is pressed, the printer counter value is cleared to 0, and "000,000" is displayed on the LCD. [Operation] 1) Initial display 24-09 PRT.CLR. CLEARED 000,000 10 FAX counter clear (FAX CLR.) (Executable only when the FAX is installed.
PAGE 82
e-STUDIO162_151.book 13 ページ Main code 26 Sub code 02 ２００４年１２月２日木曜日午後９時３７分 Contents Details of function/operation (R)ADF setting (ADF/RADF) (Executable only when the ADF/RADF is installed.) [Function] When this test command is executed, the current set ADF is displayed. Enter the code number corresponding to the desired ADF and press [OK (ENTER)/START] key to save the setting.
PAGE 83
e-STUDIO162_151.book 14 ページ Main code 26 Sub code 30 ２００４年１２月２日木曜日午後９時３７分 Contents Details of function/operation CE mark support control ON/ OFF (CE MARK) [Function] When this test command is executed, the current set CE mark support control is displayed. Enter the code number corresponding to the desired CE mark support control and press [OK (ENTER)/START] key to save the setting.
PAGE 84
e-STUDIO162_151.book 15 ページ Main code 26 Sub code 43 ２００４年１２月２日木曜日午後９時３７分 Contents Details of function/operation Side void amount setting (SIDE VOID) [Function] When this test command is executed, the currently set code of the side void quantity is displayed (initial display), and the set data are saved. (Setting range: 0 – 10, Default: 4 (= One side 2.0mm)) 9 Code 0 1 2 3 4 5 6 7 8 9 10 Setting 0 mm 0.5 mm 1.0 mm 1.5 mm 2.0 mm 2.5 mm 3.0 mm 3.5 mm 4.0 mm 4.5 mm 5.
PAGE 85
e-STUDIO162_151.book 16 ページ Main code 41 Sub code 06 ２００４年１２月２日木曜日午後９時３７分 Contents Details of function/operation OC cover float detection level (OC FLOAT LEVEL) (Disabled when set to OC) (Executable only when the ADF/RADF is installed.) [Function] When this test command is executed, the current set value is displayed. When [OK (ENTER)/START] key is pressed, the mirror base unit moves to the ADF scan position to acquire the OC cover float detection level.
PAGE 86
e-STUDIO162_151.book 17 ページ Main code 43 Sub code 05 ２００４年１２月２日木曜日午後９時３７分 Contents Details of function/operation Fusing temperature setting in duplex copy (FU TEMP DPLX) (Enabled when Duplex setting is ON) [Function] In the case of duplex copy, the shift temperature set with this test command is applied to the fusing temperature. When this test command is executed, the current set code number is displayed. Enter the desired code number and press [OK (ENTER)/START] key to save the setting.
PAGE 87
e-STUDIO162_151.book 18 ページ Main code 46 Sub code 01 ２００４年１２月２日木曜日午後９時３７分 Contents Details of function/operation Copy density adjustment (300dpi) (EXP.LEVEL 300) [Function] Copy density is set for each mode. When this test command is executed, the current se value is displayed in 2 digits (Default: 50). Change the set value and press [START] key to make a copy under the set value. When the set value is increased, the copy becomes darker. When the set value is decreased, the copy becomes lighter.
PAGE 88
e-STUDIO162_151.book 19 ページ Main code 46 Sub code 12 ２００４年１２月２日木曜日午後９時３７分 Contents Details of function/operation Density adjustment in the FAX mode (Collective adjustment) (Executable only when the FAX is installed.) [Function] When [START] key is pressed, scan is executed with the entered exposure adjustment value and the data stored on the FAX side is rewritten into the entered value. All data of the exposure adjustment values are rewritten into the same value.
PAGE 89
e-STUDIO162_151.book 20 ページ Main code 46 Sub code 15 ２００４年１２月２日木曜日午後９時３７分 Contents Details of function/operation FAX mode density adjustment (Super fine) (Executable only when the FAX is installed.) [Function] When [START] key is pressed, scan is started with the entered exposure adjustment value and the data of the selected mode on the FAX side is changed to the entered value. For the density adjustment value table data, refer to TC46-13 (FAX mode density adjustment (normal text).
PAGE 90
10_TESTCOMMAND.fm 21 ページ Main code 46 Sub code 19 ２００４年１２月１０日金曜日午前８時４１分 Contents Details of function/operation Exposure mode setting (AE MODE) [Function] <γ table setting> When this test command is executed, the code number of the current set gamma table is displayed. (Default: US -1/Ex US -2) Enter the code number corresponding to the desired gamma table, and press [←/→] key to change the mode and write into the EEPROM.
PAGE 91
e-STUDIO162_151.book 22 ページ Main code 46 Sub code 29 ２００４年１２月２日木曜日午後９時３７分 Contents Details of function/operation Image contrast adjustment (600dpi) (GAMMA 600) [Function] Contrast is set for each mode. When this test command is executed, the current se value is displayed in 2 digits (Default: 50). Change the set value and press [START] key to make a copy under the set value. When the set value is increased, the contrast becomes higher. When the set value is decreased, the contrast becomes lower.
PAGE 92
e-STUDIO162_151.book 23 ページ Main code 46 Sub code 32 ２００４年１２月２日木曜日午後９時３７分 Contents Details of function/operation Copier color reproduction setting (COLOR REAPPEAR) [Function] Used to set color reproduction in each mode. Colors easy to be copied and colors difficult to be copied can be switched.
PAGE 93
e-STUDIO162_151.book 24 ページ Main code 48 Sub code 01 ２００４年１２月２日木曜日午後９時３７分 Contents Details of function/operation Main scan/sub scan direction magnification ratio (COPY MAG.) [Function] Used to adjust the magnification ratio in the main scan (front/rear) direction and sub scan direction. Enter the adjustment value with [10KEY]. Press [START] key to save the set value and make a copy. (When the adjustment value is increased by 1, the magnification ratio is increased by 0.1%.
PAGE 94
e-STUDIO162_151.book 25 ページ Main code 49 Sub code 01 ２００４年１２月２日木曜日午後９時３７分 Contents Details of function/operation Download mode (DOWNLOAD MODE) [Function] When this test command is executed, "DLOWNLOAD MODE" is displayed on the LCD and the machine goes into the program writing mode from PC to Flash ROM. Use the writing tool on the PC and write the program. During writing, the display shows as follows: After completion of download, turn OFF/ON the power to reset.
PAGE 95
e-STUDIO162_151.book 26 ページ Main code 50 Sub code 01 ２００４年１２月２日木曜日午後９時３７分 Contents Details of function/operation Lead edge image position (LEAD EDGE) [Function] Used to adjust the copy image position and the lead edge void amount on copy paper. The adjustment is made by adjusting the image scan start position at 100% and the print start position (resist roller ON timing). When this test command is executed, the current set value is displayed in 2 digits.
PAGE 96
e-STUDIO162_151.book 27 ページ Main code 50 Sub code 06 ２００４年１２月２日木曜日午後９時３７分 Contents Details of function/operation Copy lead edge position adjustment (ADF/RADF) (ADF/RADF EDGE) (Disabled when set to OC) (Executable only when the ADF/RADF is installed.) [Function] Used to adjust the ADF copy lead edge. When the adjustment value of the document scan position adjustment is increased by 1, the scan start timing is advanced by 0.1mm.
PAGE 97
e-STUDIO162_151.book 28 ページ Main code 50 Sub code 18 ２００４年１２月２日木曜日午後９時３７分 Contents Details of function/operation Memory reverse position adjustment in duplex copy (DPLX REVERSE) (Enabled when Duplex setting is ON with OC or ADF set) (Executable only when the RADF is installed.) [Function] When this test command is executed, the current set correction value is displayed. Enter the correction value and press [START] key to save the entered correction value.
PAGE 98
e-STUDIO162_151.book 29 ページ Main code 51 Sub code 02 ２００４年１２月２日木曜日午後９時３７分 Contents Details of function/operation Resist amount adjustment (RESIST ADJ.) [Function] Used to adjust the contact pressure of the main unit resist roller and the RADF resist roller onto paper. When this test command is executed, the current set value is displayed. The adjustment modes can be selected by pressing [←/→] key. Enter the adjustment value with [10KEY] and press [START] key to save the set value and make a copy.
PAGE 99
10_TESTCOMMAND.fm 30 ページ Main code 63 Sub code 01 ２００４年１２月２２日水曜日午後３時４０分 Contents Details of function/operation Shading check (SHADING CHK) [Function] Used to display the detection level of white plate for shading. When [OK (ENTER)/START] key is pressed, the mirror base unit moves to the white plate for shading and the copy lamp is lighted.
PAGE 100
e-STUDIO162_151.book 31 ページ Main code 64 Sub code 01 ２００４年１２月２日木曜日午後９時３７分 Contents Details of function/operation Self print (1by2 mode) (SELF PRT.) [Function] The status of the optical section is ignored and printing of one page is made. Also when the print command is received from the host, printing is made. When this test command is executed, warm-up is performed and the ready lamp is lighted. (Since, however, the scanner is disabled, initializing is not made.
PAGE 101
e-STUDIO162_151.book 32 ページ Main code 66 Sub code 03 ２００４年１２月２日木曜日午後９時３７分 Contents Details of function/operation FAX PWB memory check (Executable only when the FAX is installed.) [Function] Use to check the FAX PWB memory. [Operation] 1) Initial display SELECT CHECK MEMORY PRESS ←, → 2) [←/→] or after 2sec Every time when [→] key is pressed, the second line is changed in the sequence of No. 1 → 2 → 3 → 1. When [←] key is pressed, the sequence is reversed.
PAGE 102
e-STUDIO162_151.book 33 ページ Main code 66 Sub code 05 ２００４年１２月２日木曜日午後９時３７分 Contents Details of function/operation Signal send mode (Soft SW set value) (Executable only when the FAX is installed.) [Function] Use to set the signal send mode (Soft SW set value). Facsimile test command design specifications.
PAGE 103
e-STUDIO162_151.book 34 ページ Main code 66 Sub code 11 ２００４年１２月２日木曜日午後９時３７分 Contents Details of function/operation 300bps signal send (Max. value) (Executable only when the FAX is installed.) [Function] Use to set the 300bps signal send (Max. value). 1: NO SIGNAL 2: 11111 3: 11110 4: 00000 5: 010101 6: 00001 [Operation] 1) Initial display SELECT SIGNAL PRESS ←, → 2) [←/→] or after 2sec Every time when [→] key is pressed, the second line is changed in the sequence of No. 1 → 2 → 3 → 4 → 5 → 6 → 1.
PAGE 104
e-STUDIO162_151.book 35 ページ Main code 66 Sub code 13 ２００４年１２月２日木曜日午後９時３７分 Contents Details of function/operation Dial test (Executable only when the FAX is installed.) [Function] Use to the dial test. [Operation] ■ Dial test (PULSE) 1) Initial display SELECT SIGNAL 1:PULSE 2:DTMF ∗ [CLEAR] key: FAX control is termi- nated. 2) Select 1 INPUT MAKE TIME (0-15) ■ Dial test (DTMF) 1) Initial display SELECT SIGNAL 1:PULSE 2:DTMF ∗ [CLEAR] key: FAX control is terminated.
PAGE 105
e-STUDIO162_151.book 36 ページ Main code 66 Sub code 18 ２００４年１２月２日木曜日午後９時３７分 Contents Details of function/operation DTMF signal send (Soft SW set value) (Executable only when the FAX is installed.) [Function] Use to set the DTMF signal send (Soft SW set value). [Operation] 3) Communication is started after setting the signal send level. 1) Initial display INPUT DIAL # ∗ [CLEAR] key: FAX control is terminated. SENDING SIGNAL SSW PRESS CLEAR TO STOP ∗ [CLEAR] key: Returns to "1) Initial display".
PAGE 106
e-STUDIO162_151.book 37 ページ Main code 66 Sub code 32 ２００４年１２月２日木曜日午後９時３７分 Contents Details of function/operation Receive data check (Executable only when the FAX is installed.) [Function] Use to check the receive data. [Operation] 1) Initial display 2) After completion of reception RECEIVING RESULT xx "xx" is "OK" or "NG" depending on the check result. ∗ [CLEAR] key: FAX control is terminated. 33 Signal detection check (Executable only when the FAX is installed.
PAGE 107
e-STUDIO162_151.book 38 ページ Main code 66 Sub code 38 ２００４年１２月２日木曜日午後９時３７分 Contents Details of function/operation Time setting/check (Executable only when the FAX is installed.) [Function] Use to check the time setting. [Operation] 1) Initial display SELECT TO SET 1:DATE 2:TIME ∗ [CLEAR] key: FAX control is terminated. 2) Select 1 xxxx.xx.xx(xxx) CHANGE? 1:YES 2:NO "xxxx.xx.xx(xxx)" is the current value. (No revision of display) 3) Select 1 INPUT YEAR (4 DIGITS)____.__.
PAGE 108
10_TESTCOMMAND.fm 39 ページ２００４年１２月２２日水曜日午後２時３７分 5. Trouble codes A.
PAGE 109
10_TESTCOMMAND.fm 40 ページ２００４年１２月２２日水曜日午後２時３７分 Main Sub Details of trouble code code E7 11 Content Shading trouble (White correction) Detail The CCD white scan level is abnormal when the shading. Cause Improper connection of the CCD unit flat cable Dirt on the mirror, the lens, and the reference white plate Copy lamp lighting abnormality CCD unit abnormality MCU PWB abnormality (When occurred in the ADF scan position.
PAGE 110
10_TESTCOMMAND.fm 41 ページ２００４年１２月２２日水曜日午後２時３７分 Main Sub Details of trouble code code L1 00 Content Feeding is not completed within the specified time after starting feeding. (The scan head locking switch is locked) Detail The white area and the black marking on the shading plate are used to obtain the difference in the CCD level values for judgment of lock.
PAGE 111
11_MAINT.fm 1 ページ２００４年１２月２２日水曜日午後２時７分 [11] MAINTENANCE 1. Maintenance table : Check (Clean, adjust, or replace when required.) Section Developing Process peripheral Parts 25K 50K 75K : Clean : Replace 100K 125K : Adjust ✩: Lubricate Remark Developer DV blade DV side seal (F/R) Drum 2.
PAGE 112
e-STUDIO162_151.book 1 ページ２００４年１２月２日木曜日午後９時３７分 [12] USER PROGRAM The user settings consist of the following items. 1. User programs A. Copy mode Program number Program name Setting codes (factory default setting appears in bold) 1: 10 SEC. 2: 30 SEC. 3: 60 SEC. 4: 90 SEC. 5: 120 SEC. 6: OFF 1: 30 SEC. 2: 1 MIN. 3: 5 MIN. 4: 30 MIN. 5: 60 MIN. 6: 120 MIN. 7: 240 MIN. 1: ON 2: OFF 1: 5 MIN. 2: 30 MIN. 3: 60 MIN. 4: 120 MIN. 5: 240 MIN.
PAGE 113
e-STUDIO162_151.book 2 ページ Program number ２００４年１２月２日 Program name 15 KEY TOUCH SOUND 16 18 SOUND AT DEFAULT TONER SAVE MODE AE LEVEL ADJUST 19 LANGUAGE 20 RESET FACTORY 21 SORT AUTO SELECT 17 木曜日午後９時３７分 Setting codes (factory default setting appears in bold) 1: LOW 2: HIGH 3: OFF 1: ON 2: OFF 1: ON 2: OFF 1: ADF/RADF 2: DOCUMENT GLASS 1: AMERICAN ENGLISH 2: ENGLISH 3: FRENCH 4: SPANISH : : 1: Yes 2: No 1: ON 2: OFF Explanation • This sets the volume of beep signals.
PAGE 114
e-STUDIO162_151.book 3 ページ２００４年１２月２日木曜日午後９時３７分 2. Selecting a setting for a user program 1) Press the [MENU] key and then press the [OK (ENTER)] key. In printer mode, the user programs are accessed by simply pressing the [MENU] key. (e-STUDIO151/151D) (e-STUDIO162/162D) MAIN MENU 1:USER PROGRAM MAIN MENU 1:USER PROGRAM OK 1 1 2 2 2 1,2,3, 1,2,3, 2 1 1 AUTO ZOOM SP.
PAGE 115
5V MCU-PWB CCD (uPD8861) 12V Reg SDRAM e-STUDIO162/162D/151/151D ELECTRICAL SECTION 13 - 1 Driver Driver Sensor/SW PAPD,PPD3, PD2,CED2 Mechanical load CPFS2 3.3V Toner Motor Driver Mirror Motor Driver (296pin) LSU LASER D[15…0] A[19…1] Polygon Motor LCX574 2Kbyte EEPROM OP-CLK OP-LATCH OP-DATA POWER SUPPLY AC Code D[7..
PAGE 116
e-STUDIO162_151.book 2 ページ２００４年１２月２日木曜日午後９時３７分 2. Circuit descriptions A. Main PWB (MCU) (1) General The MCU PWB is composed of: • CPU peripheral section which performs mechanical sequence control, U/I, and each function job management. The CPU connects with the ASIC and memory by use of the system bus and performs jog management and sequence control of the whole engine. • Image process ASIC which performs image process, CCD control, LSU control, and print control.
PAGE 117
e-STUDIO162_151.book 3 ページ PIN No.
PAGE 118
e-STUDIO162_151.book 4 ページ２００４年１２月２日木曜日午後９時３７分 b. ASIC (Signal table) PIN No.
PAGE 119
e-STUDIO162_151.book 5 ページ２００４年１２月２日木曜日午後９時３７分 PIN Signal Name IN/OUT Connected to Description No.
PAGE 120
e-STUDIO162_151.book 6 ページ PIN No.
PAGE 121
午後９時３７分 PIN Signal Name IN/OUT Connected to Description No.
PAGE 122
e-STUDIO162_151.book 8 ページ２００４年１２月２日木曜日午後９時３７分 (5) Heater lamp control circuit The CPU converts the inputted analog voltage into a digital value. The digital conversion value and the set value of the test command are compared to control ON/OFF of the heater lamp according to the level, controlling the heat roller surface temperature to be the fixed level. 12V 1 VCC3 1 R68 7.5kF 1 FTH (5-B2) 2 1 12V C110 0.1u 2 R71 4.
PAGE 123
e-STUDIO162_151.book 9 ページ２００４年１２月２日木曜日午後９時３７分 (7) Toner motor control circuit The IC32 is the motor drive IC, which generates pseudo-AC waveforms by the pulse signal from the ASIC to drive the toner supply motor. Tonner Motor Driver 1 + C129 2 1 24V 0.
PAGE 124
e-STUDIO162_151.book 10 ページ２００４年１２月２日木曜日午後９時３７分 Scanner Motor Driver (10-D2) (10-D2) (10-D2) (10-D2) OUT_AOUT_A+ OUT_B+ OUT_B- 24VM 5V R89 R90 1 PGND 2 (2-A3) MM_BI0 (2-A3) MM_BI1 (2-A3) MM_PH_B 1 1 R93 1kJ 24 23 22 21 20 19 18 17 16 15 14 13 VS SENSE 1 COMP 1 OUT 1B I01 GND GND I11 PHASE 1 VREF 1 RC 1 VSS MM_AI0 1 L6219DS or AMM56219 R94 30kJ R95 30kJ C118 820p 2 1 2 PGND PGND PGND PGND 1 2 2 2 MMref0 MMref1 MMref2 C121 0.1u 2 (5-C1) (5-C1) (5-C1) PGND 5V C119 0.
PAGE 125
e-STUDIO162_151.book 11 ページ２００４年１２月２日木曜日午後９時３７分 (10) OPE PWB (11) Carriage Unit a. Outline The operation circuit is composed of the LCD control circuit, the key matrix circuit, the display matrix circuit, and the buzzer circuit, realizing the U/I functions. b. LCD control circuit The character LCD (COG) in 2 lines and 16 digits is used. The display data are sent from the MCU (CPU) to LCD internal registers, controlling the LCD. c.
PAGE 126
e-STUDIO162_151.book 12 ページ２００４年１２月２日木曜日午後９時３７分 Since the AC power is directly rectified, if there were not this rush current prevention resistor (TH001), an extremely large rush current would flow due to a charging current flowing through the smoothing capacitor C006 when turning on the power. To prevent against this, the rush current prevention resistor TH001 is provided between the rectifying diode D003 and the smoothing diode C006, suppressing a rush current.
PAGE 127
14_CIRCUTDIAGRAM.fm 1 ページ２００４年１２月２日木曜日午後７時７分 [14] CIRCUIT DIAGRAM 1. MCU PWB A B C MCU PWB (CPU section) VCC3 When IC1 is, mounted R4(*3) OPEN 0J R3(*1) OPEN 680J 4 Spreading Range : +/- 1.25% C1 *6 NOT mounted R7(*4) 22J OPEN R2(*2) 0J OPEN C3(*5) 22pF 15pF C1(*6) 22pF 15pF R1 OPEN IC1 8 7 VDD 6 SR0 5 MODOUT SSon VCC3 C2 0.1u R2 1 Xin 2 Xout 3 FS0 4 Vss *2 R3 X1 HC-49U/S 19.
PAGE 128
14_CIRCUTDIAGRAM.
PAGE 129
14_CIRCUTDIAGRAM.
PAGE 130
14_CIRCUTDIAGRAM.fm 4 ページ２００４年１２月２日木曜日午後７時７分 C D E 2/14 VCC3 0.1 u 0.1 u 0.1 u 0.1 u 0.1 u 0.1 u 0.1 u 10KJ 5 6 7 8 G3.3V 0.1 u BR93 4 3 2 1 VCC3 L2 ZJSR5101-102TA 0.1 u 10KJ 5 6 7 8 0.1 u BR25 4 3 2 1 C35 C34 C33 C32 C31 C30 C29 C28 C27 C26 C36 + 47u/16V 4 0.1 u 0.1 u 0.1 u C64 C46 0.1 u 0.1 u C63 C45 0.1 u 0.1 u C62 C44 0.1 u 0.1 u C61 C43 0.1 u 0.1 u C60 C42 0.1 u 0.1 u C59 C41 0.1 u 0.1 u C58 C40 0.1 u C39 0.1 u C57 0.1 u C38 C37 /H_SYNC (8-A2) 0.
PAGE 131
14_CIRCUTDIAGRAM.fm 5 ページ２００４年１２月２日木曜日午後７時７分 A B C MCU PWB (Memory section) 4 (1-C1) (2-A1) A[19..0] 3 10kJ 0J R47 R48 VCC3 V R49 10kJ IC7 IC8 5 28 12 CS1 OE WE 6 7 10 11 22 23 26 27 A16 A15 A14 A13 A12 A11 A10 A9 D8 D9 D10 D11 D12 D13 D14 D15 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 HWRZ /RESET0 VCC3 VCC3 (1-D3) RY/BY VDD VDD GND GND A19 A18 A8 A7 A6 A5 A4 A3 A2 8 24 C73 C74 0.1u 0.
PAGE 132
14_CIRCUTDIAGRAM.fm 6 ページ２００４年１２月２日木曜日午後７時８分 C D E 3/14 4 RAMDB[15..
PAGE 133
14_CIRCUTDIAGRAM.fm 7 ページ２００４年１２月２日木曜日午後７時８分 A B C MCU PWB (Driver section 1) Digital Input Multiplexer 5V 5V/3.3 IC9 (7-E2) (7-E4) (7-E3) (7-E1) (7-E3) (7-E4) (7-E3) (7-E1) (PPD1) (POD) (MFD) (CED1) (TCS) (PMRDY) DVS1 (DRST) 4 3 2 1 15 14 13 12 (10-E3)(4-E2) (10-E3)(4-E2) (10-E3)(4-E2) (SELIN1) (SELIN2) (SELIN3) 11 10 9 7 4 VCC D0 D1 D2 D3 D4 D5 D6 D7 16 R56 Y W A B C G GND 5 (10-C4) KEYIN SIN1 SIN2 SIN3 SPFS SRRC SGS SPUS SIN1 (4-C4) 10J 6 C83 C84 0.
PAGE 134
14_CIRCUTDIAGRAM.fm 8 ページ２００４年１２月２日木曜日午後７時８分 C D E 4/14 5V VCC3 VCC3 3.3V 5V/3.3V R54 10kJ IC10 2 4 6 8 11 13 15 17 1 19 10 1A1 1A2 1A3 1A4 2A1 2A2 2A3 2A4 1G 2G GND VCC 1Y1 1Y2 1Y3 1Y4 2Y1 2Y2 2Y3 2Y4 20 18 16 14 12 9 7 5 3 (KEYIN) (1-A3) (SIN1) (SIN2) (SIN3) SPFS# SRRC# SGS# SPUS# IC45 Vcc 1 (11-B2) /SYNC 3 A1 Y1 A2 Y2 5 6 (/SYNC) (2-E1) 4 C379 4 C85 0.1u GND 47p 2 NC7WZ17 C86 0.1u 74LCX244 C3 VCC3 3.
PAGE 135
14_CIRCUTDIAGRAM.fm 9 ページ２００４年１２月２日木曜日午後７時８分 A B C MC UP WB( Dr i v ers ec t i o n2 ) 24V 4 BR107 1 2 3 4 (2-C1) MC (2-C1) BIAS (2-C1) TC (2-C1) GRIDL MCNT CPFS2 1.5kJ 8 7 6 5 IC21 1 2 3 4 5 6 7 8 R325 1.5kJ R343 1.5kJ 1C 2C 3C 4C 5C 6C 7C COM 1B 2B 3B 4B 5B 6B 7B E 16 15 14 13 12 11 10 9 /MC /BIAS /TC /GRIDL /MCNT (10-B4) (10-A4) (10-B4) (10-A4) /CPFS2 KID65001AF PGND 24V (2-D1) (2-D1) (2-C1) BR108 1 2 3 4 CPFS1 MPFS RRS 1 2 3 4 (2-C1) VFM (2-C1) VFMCNT (2-D1) PR 3 BR109 1.
PAGE 136
14_CIRCUTDIAGRAM.fm 10 ページ２００４年１２月２日木曜日午後７時８分 C D E 5/14 4 /MC /BIAS /TC /GRIDL /MCNT (10-B4) (10-A4) (10-B4) (10-A4) /CPFS2 VCC3 R67 1MF VCC3 R68 7.5kF R69 1kJ 8 R66 1kF 12V 3 + D1 IC22A KIA393F 1 FTH (5-B2) 2 R70 10kF R71 4.3kF 12V 4 MA700 C110 0.1u 24V R73 /CPFS1 /MPFS /RRS (11-B3) VCC3 VCC3 47kJ D3 D2 R78 Q1 KTA1505S /VFMCNT (11-A3) 4.
PAGE 137
14_CIRCUTDIAGRAM.fm 11 ページ２００４年１２月２日木曜日午後７時１０分 A B C MCU PWB (Driver section 3) 4 Scanner Motor Driver (10-D2) OUT_A(10-D2) OUT_A+ (10-D2) OUT_B+ (10-D2) OUT_B- 24VM 5V R89 R90 0.
PAGE 138
14_CIRCUTDIAGRAM.fm 12 ページ２００４年１２月２日木曜日午後７時１０分 C D E 6/14 Duplex Motor Driver 4 IC28 3 4 5 6 10 11 12 13 14 15 (1-D3) DMT0 (1-D3) DMT1 (1-D3) DMT2 (1-D3) DMT3 17 18 O1 I1 NC NC I2 NC I3 NC NC I4 NC GND GND O2 2 /DMT0 (11-B3) 7 /DMT1 (11-B3) 9 O3 /DMT2 (11-B3) 16 O4 /DMT3 (11-B3) 24VDup COM COM D5 1 8 TD62064AF MTZ J22B PGND Shifter Motor Driver 24V IC30 CP1 0603FA1.5A (4-B2) SFTMT0 24VSFT (4-B2) SFTMT1 CP3 0603FA1.5A 5A (4-B2) SFTMT2 24VDup V C124 0.
PAGE 139
14_CIRCUTDIAGRAM.fm 13 ページ２００４年１２月２日木曜日午後７時１１分 A B C MCU PWB (Noise filter/Pull-up section) 4 VCC3 5V C138 C139 C140 C141 C142 C143 C144 C145 C146 0.1u OPEN 0.1u 0.1u OPEN OPEN OPEN OPEN OPEN D11 1 3 2 KDS226 C147 C148 C149 C150 C151 C152 C153 C154 C155 OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN OPEN C156 C157 C158 C159 C160 C161 C162 C163 C164 OPEN OPEN OPEN OPEN 0.1u 0.
PAGE 140
14_CIRCUTDIAGRAM.fm 14 ページ２００４年１２月２日木曜日午後７時１１分 C D E 7/14 5V 1 D7 3 2 1 D8 KDS226 1 3 2 D9 KDS226 1 3 2 D10 KDS226 4 3 2 R116 10kJ R117 10kJ R118 10kJ R119 4.
PAGE 141
14_CIRCUTDIAGRAM.fm 15 ページ２００４年１２月２日木曜日午後７時１１分 A B C MCU PWB (IMC2 section 1/2) IC37 (2-D3) (2-D4) 119 120 124 125 126 127 128 129 131 132 133 134 135 137 138 141 142 /PIWR (2-D3) /PIACK (2-D3) /PIREQ PIDATA[7..
PAGE 142
14_CIRCUTDIAGRAM.
PAGE 143
14_CIRCUTDIAGRAM.fm 17 ページ２００４年１２月２日木曜日午後７時１２分 A B C MCU PWB (IMC2 USB2.0 section 2/2) 4 VCC3 C314 0.01U C315 0.01U C316 0.01U C317 0.01U C318 0.01U C319 0.01U VCC3 VCC3 GND C323 0.1U C324 0.1U C325 0.1U C326 0.1U C327 0.1U C328 0.1U C320 + 10U/16V GND VCC3 (9-B3) (13-C4) PB_ADDR[7:0] C338 0.1U GND C339 0.
PAGE 144
14_CIRCUTDIAGRAM.fm 18 ページ２００４年１２月２日木曜日午後７時１２分 C D E 9/14 4 C321 0.1U + C322 10U/16V 10KJ 10KJ 10KJ NC 10KJ R281 R282 R284 R287 AG R280 VCC3 GND 17 18 16 22 21 62 63 /CS1 /CS0 INTRQ READY DA2 WAKEUP SUSPEND 3 PB_NOE PB_NWE 14 15 20 9 19 DIOR DIOW MODE0 MODE1 BUS_CONF R283 R285 10KJ 10KJ R286 R288 10KJ NC WAKEUP (8-A2) SUSPEND (8-A2) R289 10KJ C329 60 XTAL1 59 XTAL2 Y1 10P GND 12MHz C330 4 Vreg(3.3) R293 1.
PAGE 145
14_CIRCUTDIAGRAM.fm 19 ページ２００４年１２月２日木曜日午後７時１２分 A B C MCU PWB (Connector section 1) To Power unit 4 INT5V INT24V CN1 C208 1 3 5 7 9 11 13 15 17 19 21 23 2 4 6 8 10 12 14 16 18 20 22 24 2 4 6 8 10 12 14 16 18 20 22 24 /TC /MC (5-C4) (5-C4) 3.3VIN (7-B2) /POFF 24V (5-C1) (7-A2) HLOUT (5-D2) B24B-PHDSS-B 0.1u/50V 2 C207 0.
PAGE 146
14_CIRCUTDIAGRAM.
PAGE 147
14_CIRCUTDIAGRAM.fm 21 ページ２００４年１２月２日木曜日午後７時１３分 A B MCU PWB (Connector section 3) 4 To Mech. COUNTER 24V CN8 3 2 1 /MCNT B3B-PH-K-S 3 To Cover open detect 5V 5V D37 1 3 2 KDS226 R177 4.
PAGE 148
14_CIRCUTDIAGRAM.fm 22 ページ２００４年１２月２日木曜日午後７時１３分 C D 11/14 To 2nd.
PAGE 149
e-STUDIO162/162D/151/151D CIRCUIT DIAGRAM 14 - 23 1 /ACK BUSY PE SLCT /FAULT (2-D2) /REV /OA_RST (2-D2) /STB (2-D2) /AUTOFD (2-D2) /SLCTIN (2-D2) /INIT (2-D2) (2-D2) (2-D2) (2-D2) (2-D2) (2-E2) PARAD[7..0] VCC3 EN5V CN39 R197 10kJ A R319 0J PARAD0 PARAD1 PARAD2 PARAD3 PARAD4 PARAD5 PARAD6 PARAD7 /ACK BUSY PE SLCT /FAULT /STB /AUTOFD /SLCTIN /INIT R326 /REV OPEN To NIC PWB 24FMN-BTK-A 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0.1u B C243 0.
PAGE 150
1 2 3 A (4-A3) MODEM_IN (1-B3) (2-C1) (3-A2) /RD (1-D3) /CS4 MSU_ST1 (1-A3) (2-D1) (9-B2) (8-A3) 2 1 4 NC7S32M5X IC46 MDM_IRQ B (1-D2) (2-A1) (3-A1) (4-A2) D[15..0] MSU_ST1 R306 10kJ VCC3 /FWREN PB_NWE VCC3 R357 N.M. (8-A2) PB_NOE /OA_RST MDM_IRQ (2-D1) PB_NCS1 PB_NAE0 (9-B2) (8-A3) PB_ADDR[7:0] (8-A3) (9-A2) (8-A3) (8-A3) (9-B3) (8-A3) (9-B3) (9-B3) PB_DATA[7:0] 5 3 4 MCU PWB (Modem I/F Connector) B D7 D6 D5 D4 D3 D2 D1 D0 C402 PGND 24V EN5V VCC3 0.
PAGE 151
A R169 15kJ R170 56kJ + R166 10kJ PGND Q5 KTC3198 R168 5.6kJ 1/4W Q4 KTB1151 Y D33 11EQS06 B TWKA-221K L9 220uH 47u/35V + C214 0.1u/50V C215 R167 15kJ CP4 0603FA1.5A VCL C (1-D2) mt_at_home C R165 1kJ 1000p C212 R164 10kJ VCC3 2 1 3 KDS226 D32 (2-A4) (2-A4) (2-A4) (2-A4) (2-A4) (1-D2) (2-A4) e-STUDIO162/162D/151/151D CIRCUIT DIAGRAM 14 - 25 D AFE_DB[7..
PAGE 152
e-STUDIO162/162D/151/151D CIRCUIT DIAGRAM 14 - 26 1 2 3 OP-LATCH OP-DATA OP-CLK A Open C308 1 2 KRC106S Q302 R324 0J 1 3 2 3 R323 10KJ 3.3V R325 0J 1 Q304 KRA225S 3 Q303 KRA225S 1 4 5V 2 OPERATION PWB (LED/LCD Section) R303 3 B R326 0J Q305 KRA225S 2 B R304 100J R302 0.1u C322 3.
PAGE 153
e-STUDIO162/162D/151/151D CIRCUIT DIAGRAM 14 - 27 1 KRC106S 47pF C315 A Open Open Open C311 C310 C309 KEYIN Open Open Open C318 C319 C320 2 R317 R316 R315 R318 R338 R337 R336 3 0.1u PSW 5V 0.
PAGE 154
B 47uF/16v C301 0.1u C326 Close to CN1 C 18FE-ST-VK-N 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 CN301 To FAX Key PWB F-KEYIN7 F-KEYIN6 F-KEYIN5 F-KEYIN4 F-KEYIN3 F-KEYIN2 F-KEYIN1 F-KEYIN8 F-KEYSC3 F-KEYSC2 F-KEYSC1 LED_V3 LED_V2 LED_V1 DATA1 D DRST S3B-PH-K-S 1 2 3 CN303 To Drum Initial Detector E 3/3 3 4 1 LCDE LCDRS BZR KEYSC1 KEYSC2 KEYSC3 LCDDB[7..4] 0.
PAGE 155
14_CIRCUTDIAGRAM.fm 29 ページ２００４年１２月２日木曜日午後７時１４分 3.
PAGE 156
14_CIRCUTDIAGRAM.
PAGE 157
14_CIRCUTDIAGRAM.
PAGE 158
14_CIRCUTDIAGRAM.
PAGE 159
e-STUDIO162/162D/151/151D CIRCUIT DIAGRAM 14 - 33 PD1 1 2 MPFS PD1 D-GND PPD1 CED1 D-GND CPFS1 1 2 DSW RRS OPTIONAL (FAX) BR GY BR GY RD RD CN15 1 24V 2 24V1(DSWS) 1 2 3 4 5 CN26 24V /MPFS LEDMFD MFD D-GND CN25 PD1 D-GND 1 2 PK GY CN7 CED1 D-GND PK PL GY 1 2 CN16 1 LEDPPD1 2 PPD1 3 D-GND BR GY BL PK PL GY RD CN10 1 24V 2 /CPFS1 CN12 24V /RRS 1 2 TM BL PK PL GY RD CN23 TMA-O TMB-O 1 2 5 6 7 8 1 2 3 4 5 PMCLK-A PMRDY /PMD P-GND 24V 1 2 24V 24V /MM MMLD GND GND PM PK GY
PAGE 160
PWB MCU CN24 D-GND 3 6 SDSW 5 SPID 7 SB4B 8 5V 24V 11 12 /SPUS 1 D-GND 2 SPPD LEDSPPD 4 SPMT-1 19 SPMT-3 20 SPMT-2 21 SPMT-0 22 24Vmir 23 24Vmir 24 24V 13 /SPFS 14 24V 15 /SRRC 16 24V 17 /SGS 18 OR OR RD BR GY BR PK PL PK BL BR RD RD RD PK RD PL RD BL e-STUDIO162/162D/151/151D CIRCUIT DIAGRAM 14 - 34 RD BL RD PL 1 2 1 2 24V /SGS 24V /SRRC 24V /SPFS 24V /SPUS D-GND SDSW SPID SB4B 5V 2 1 2 1 2 1 2 1 5 4 3 2 1 OR GY PL BL R-ADF UNIT PL PK BL BR RD RD GY BR PK 5 4 3 2 1 3 1 6 4 2 5 SPMT
PAGE 161
CN33 5V USB DATA DATA + D-GND 1 2 3 4 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 CN38 D-GND MSU_ST1 /CS4 /RD MODEM_IN D0 D1 D2 D3 D4 D5 D6 D7 P-GND 24V D-GND EN5V VCC3 VCC3 D-GND 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 CN1 D-GND MSU_ST1 /CS4 /RD MODEM_IN D0 D1 D2 D3 D4 D5 D6 D7 P-GND 24V D-GND EN5V VCC3 VCC3 D-GND CN2 D-GND MDM_IRQ (/FAX_RST) PB_MOE PB_NWE PB_NAE0 PB_NCS1 D-GND PB_ADDR0 PB_ADDR1 PB_ADDR2 PB_ADDR3 PB
PAGE 162
e-STUDIO162_151.book 1 ページ２００４年１２月２日木曜日午後９時４８分 [15] FIRMWARE DOWNLOAD PROCEDURES 2) Select "Option" → "Serial Number Setting" on the menu bar. [Preparation] Write the download data (extension .dwl) into the main unit. A USB port is required for the PC. Create "MaintenanceTool " flooder in the PC, and copy the following files to the folder. Necessary for program download • • • • • • Maintenance.exe (← Tool program) ProcModelB.mdl ProcModelC.mdl ProcModelE.fmt ProcModelE.ini ProcModelE.
PAGE 163
e-STUDIO162_151.book 2 ページ２００４年１２月２日木曜日午後９時４８分 4) PC side: Check that the "Simulation Command List" tree is displayed on the integration maintenance program. 5) PC side: When the integration maintenance program is boosted and "The copier is not turned on." is displayed at the bottom of display, select "File" → "Reconnect" on the menu bar. 8) PC side: Specify the download file (*****.dwl) to be used. 9) PC side: When a download file is specified, downloading is performed automatically.
PAGE 164
e-STUDIO162_151.book 3 ページ２００４年１２月２日木曜日午後９時４８分 Note: When another machine is connected, connect the USB cable again and select "File" → "Reconnect" on the menu bar of the integration maintenance program. Repeat the above procedures from 5). ∗ Inhibition during download (Important) 4) PC side: Check that the "Simulation Command List" tree on the integration maintenance program. 5) PC side: Boot the integration maintenance program. If "The copier is not turned on.
PAGE 165
e-STUDIO162_151.book 4 ページ２００４年１２月２日木曜日午後９時４８分 7) PC side: Double-click "Special (MCU/IMC2/Facsimile)" in the main tree items to develop its sub trees. Select "Get Version" in the sub trees. 8) Check that the following display is shown. With the above procedures, version acquisition is completed. • The display of "**.**" means its version is not downloaded. The downloaded versions are displayed in a version number as shown in “MCU Boot Version” and “MCU program Version”. 4.
PAGE 166
e-STUDIO162_151.book 5 ページ２００４年１２月２日木曜日午後９時４８分 7) PC side: Double-click "Special (MCU/IMC2/Facsimile)" to develop its sub trees, and select "Upload EEPROM Data Area" in the sub trees. 5. Installing procedures Driver installation is made on plug-and-play. 1) Main unit side: Execute Test command No. 49-01 (Flash ROM program write mode). Check that "DOWNLOAD MODE" is displayed on the LCD of the operation panel.
PAGE 167
e-STUDIO162_151.book 6 ページ２００４年１２月２日木曜日午後９時４８分 5) Select the folder which includes the maintenance tool driver (Mainte.inf) and press button. (Suppose that the driver is included in C:\MaintenanceTool\Drivers\ 2kXp folder.) 6) Check the path to the folder which includes the maintenance tool driver (Mainte.inf), and press button. 8) When the following display is shown, installation is completed. Press button.
PAGE 168
e-STUDIO162_151.book 7 ページ２００４年１２月２日木曜日午後９時４８分 5) Select [Specify a location] and press button. 6) Select [Include this location in the search;]. If the search location is not the folder which includes the maintenance tool driver (Mainte.inf), select . If the search location is the folder which includes the maintenance tool driver, press button to go to procedure 9). 7) Specify the folder which includes the maintenance tool driver (Mainte.inf), and press button.
PAGE 169
e-STUDIO162_151.book 8 ページ２００４年１２月２日木曜日午後９時４８分 1) Main unit side: Execute Test command No. 49-01 (Flash ROM program write mode). Check that "DOWNLOAD MODE" is displayed on the LCD of the operation panel. (Press and hold [CA] key and [DOWN] key (left key) together, and turn on the power simultaneously.) 2) Connect the machine and the PC with a USB cable. 3) The following display is shown on the PC side. Select [Specify the location of the driver], and press button.
PAGE 170
memo.
PAGE 171
memo.
PAGE 172
memo.
PAGE 173
e-STUDIO162_151.book 1 ページ２００４年１２月２日木曜日午後９時４８分 LEAD-FREE SOLDER The PWB’s of this model employs lead-free solder. The “LF” marks indicated on the PWB’s and the Service Manual mean “Lead-Free” solder. The alphabet following the LF mark shows the kind of lead-free solder. Example: Lead-Free 5mm Solder composition code (Refer to the table at the right.
PAGE 174
e-STUDIO162_151.book 2 ページ２００４年１２月２日木曜日午後９時４８分 CAUTION FOR BATTERY REPLACEMENT (Danish) ADVARSEL ! Lithiumbatteri – Eksplosionsfare ved fejlagtig håndtering. Udskiftning må kun ske med batteri af samme fabrikat og type. Levér det brugte batteri tilbage til leverandoren. (English) Caution ! Danger of explosion if battery is incorrectly replaced. Replace only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to manufacturer’s instructions.
PAGE 175
e-STUDIO162_151.book 3 ページ２００４年１２月２日木曜日午後９時４８分 Trademark acknowledgements • Microsoft® Windows® operating system is a trademark or copyright of Microsoft Corporation in the U.S.A. and other countries. • Windows® 95, Windows® 98, Windows® Me, Windows NT® 4.0, Windows® 2000, and Windows® XP are trademarks or copyrights of Microsoft Corporation in the U.S.A. and other countries. • IBM and PC/AT are trademarks of International Business Machines Corporation.
PAGE 176
2-17-2, HIGASHIGOTANDA, SHINAGAWA-KU, TOKYO, 141-8664, JAPAN