Warning! Important Safety Instructions (Please read the appropriate section that corresponds to the marking on your Samsung product before attempting to install the product.) CAUTION RISK OF ELECTRIC SHOCK REE CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). THERE ARE NO USER SERVICEABLE PARTS INSIDE. REFER ALL SERVING TO QUALIFIED PERSONNEL. JN This symbol indicated high voltage is present inside. It is dangerous to make any kind of contact with any inside part of this product.
Regulatory Compliance Statements Your Samsung product is marked to indicate its compliance class: Federal Communications Commission (FCC) USA Industry Canada Equipment Standard for Digital Equipment (ICES-003) Canada Voluntary Control Council for Interference (COCCI) Japan ~ Bureau of Standards Petrology and Inspection (SMITH) Taiwan Ministry of Information and Communication (MIC) Republic of Korea Malian Post Ministry (Homogenization) Tracy FCC Information FCC Class A Notice This device complies with part
guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which cin be determined by turning the equipment off and on, the user is encouraged to fry to correct the interference by one or more of the following measures: -Reorient or relocate the receiving antenna.
Important Safety Instructions(TV Only) 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5} Do not use this apparatus near water, 6) Clean only with dry cloth. 7) Do not block any ventilation openings, Install in accordance with the manufacturer’s instructions. 8) Do not install] near any heat sources such as radiators, heat registers, or other apparatus {including amplifiers) that produce heat.
CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELEV TIC SHOCK, DO NOT REMOVE COVER {OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL, “This symbol stenches bi voltage is resent ini. 1s thrashing tm rake any Kind of contact vita any inside par. of this product This symbol alerts you that import literature concerting operation and maintenance has bee includes with this product.
Wiring the Mains Power Supply Plug(UK Only) IMPORTANT NOTICE The mains lead on this equipment is supplied with a molded plug incorporating a fuse. The value of the fuse is indicated on the pin face of the plug and, if it requires replacing, a fuse approved to BS 11362 of the same rating must be used, Never use the plug with the fuse cover omitted if the cover i detachable. If a replacement fuse cover is required, it must be of the same color as the pin face of the fig.
MPR il Compliance COSTCO-Ecolagical requirements for personal computers (COSTCO applied model only) COSTCO-Erologleal requirements for personal computers (TCO'9S applied model ably) COSTCO-Ecological requirements for personal computers {TCO'03 appalled model ably) COSTCO Ra cycling information (TCO'03 applied mode Monty) Medical Requirement {Medical applied mod! only) + MPR Hl Compliance This monitor complies with SWEDENBORG 1} recommendations for reduced electric and magnetic fields.
La belled products must meet strict environmental demands, for example in respect of the reduction of electric and magnetic fields, along with physical and visual ergonomics and good usability.
» requirements for personal computers (TCO'99 applied model only) Congratulations You have just purchased a TCO'99 approved and labeled product! Your choice has provided you with a product developed for professional use, Your purchase has also contributed to reducing the burden on the environment and also to the further development of environmentally adapted electronics products.
The relevant TCO'98 demand requires that plastic components weighing more than 25 grams. must not contain flame retardants with organically bound bromine or chlorine. Flame retardants are allowed in the printed circuit boards since no substitutes are available. Cadmium™ Cadmium is present in rechargeable batteries and in the color-generating layers of certain computer displays. Cadmium damages the nervous system and is toxic In high doses.
Emissions + Electromagnetic fields + Noise emissions Ecology « The product must be prepared for recycling and the manufacturer must have a certified environmental management system such as MEAS or ISO 14 060 « Restrictions on © chlorinated and abominated flame retardants and polymers © heavy metals such as cadmium, mercury and lead. The requirements included in this label have banes developed by TCO Development in perpetration with scientists, experts, users as well as manufacturers all over the world.
user is encouraged to try fo correct the interference by one or mere of the following measures: + Reorient or relocate the receiving device, « Increase the separation between the equipment. + Connect the equipment into an outlet on a circuit different from that to which the other device {s} are connected. + Consult the manufacturer or field service technician for help.
9/5/05 8:51 AM Page 2. Important Warranty Information Regarding Monitor Format Viewing Wide screen format FDP Displays (16:9, the aspect ratio of the screen width to height] are primarily designed to view wide screen format full-motion video. The images displayed on them should primarily be in the wide screen 14:9 ratio format, or expanded to fill the screen if your mode! offers this feature and the images are constantly moving.
ISBN-00852B-00ENg (002-025) 9/5/05 8:51 AM Page 3. User Instructions © Screen Image retention Do not display a still image [such as on a dives game or when hooking this PDP Monitor) on the plasma monitor panel for more than 2 hours as it can cuss screen image retention, This image retention is also known as “screen burn”. To avoid such image retention, reduce the degree of brightness and contrast of the screen when displaying a still image.
9/5/05 8:51 AM Page A Table of Contents General Information Your Mew Plasma Display Remote Control BU HONS vcr servers ere mn Before using the Multiple Display Control function 13 Connections Connecting a VCR 6 Connecting a Camcorder 7 Connecting a DVD Player (480i, 480p] 18 Connecting a DTV Receiver [480p, 720p, Connecting to HDMI {High Definition Multimedia Interface) (480p, 720p, 1080i) ..
BN68-008528-00Eng (002-025) 9/5/05 9:51 AM Page 5, Function Description Selecting a Menu Language Digital Noise Reduction... Setting the Blue Screen Using the Color Weakness Enhancement Option . Using the Energy Saving Feature Preventing Screen Burn .. Reducing the Effects of Screen Bum 84 Setting the MDC [Multiple Display Coronal) Appendix Troubleshooting Care and Maintenance Specifications... ..
BN68-00852B-D0ENg (002-025) 9/5/05 8:51 AM Page | i T PLASMA DISPLAY PANEL General Information Your New Plasma Display Panel Remote Conrail Buttons Before Using the Multiple Display Control function
9/7/05 2:41 BM Page § [2] Your New Plasma Display Panel < oT + rma TIES SOURCE button © C= (Enter) button Press to display all of the available video Press to confirm o selection. sources [AV], AV2, Ideologue, Videodisc, wore button Component], Component, FC, DV and OHMS. ° Press to tum the PDP Monitor on ond off. © Mil nation Power indicator Displays the main on-screen menu.
BN68-008526-00B0g (002-025) 9/5/05 8:51 AM Page & schmooze @— S-Video Input wore @ Video input ° wn ® [ute Input Checking Accessories I Once you have unpacked your PDP Monitor, check to make sure that you hove oll the parts shown here oh If any piece is missing or broken, call yous dealer.
| BN68-00852B-00Eny {002-025} 10 9/5/05 8:51 BM Page 10 © POWER IN Connect the supplied power cord. © HOMING Connect to the HDMI jack of a device with HOMO output, OVI ~ DVI : Connect to the video output jack for device with DVI output. = AUDIO £/R : Connect ta the audit output jack for devices with DVI output. OPINION Connect to the video output jack on your PC. © COMPONENT IN 1, 2 Video [Y/Pa/PR) and audio (CLAUDIO) component inputs.
BN6B-00852B-00Eng (002-025) 9/5/05 8:51 AM Page Sleepless Display [2] Remote Control Buttons LEON € POWER button o Turns the POP Monitor on and off, © ZOOM button Press to magnify the screen. © STILL button Crass to pause the current screen. © Huber buttons © +100 button Press fo select channels over 100. For example, to select channel ~~ @—773 121, press then press “2 and “1.% i © MUTE button Press to mute the PDP Monitor sound. © VOL (Volume) buttons Use it fo adjust volume.
EN-008525-008ng( 002-025) 9/5/05 8:51 M4 Page 12 0 @ SLEEP button Press to select a preset time Interval for automatic shutoff. @ SRS tuition Selects Sensurround XT mode, € AUTO button Press lo reset automatically screen quality and position in PC mode. @ SIZE button Select Picture size. [Refer to page 40} @ PIP control buttons Pl Activates picture in picture. {Refer to page 42} Size: Press to make the PIP window Large, Small or Double.
9/5/05 8:51 AM Page 13 0 i SEE) Before Using the Multiple Display Control function Multiple Display Control connections > You con connect a Composite {Video) without a distributor as you would connect a PC. Select ID input on the menu. Use the numeric buttons to enter the ID for PDP Monitor adjustment. You can operate the cremate control! only for the PDP Monitor that has been selected.
8/6/05 8:51 AM Page 16 i Power cord 16 % Connecting a VCR Connecting a VCR to the Video or suck PDP Monitor Rear Panel 880068 (ED |v BO) same © 6/06 8 ° a Audio cable Video cable S-Video cable Connect the Video/Audio cables between the VIDEO or AUDIOVISUALS input jacks on the i (Note: For better video, use an Davidson cobble) | Note | | PDP Monitor and VIDEO er AUDIOVISUALS output jacks on the VCR. ! ie Please be sure fo match the color coded input terminals and cable jacks. © Videotape Playback: i 1.
'BN68-00852B-00Eng (002-025) 8/5/05 8:51 AM Page 1% ee Peeing © Display Wl Connecting a Camcorder Viewing camcorder tapes Sade of the PDP Monitor S-Video cobble Camcorder Video cable Power cord Connect a Video/Audio cable between the VIDEO or input jacks on the PDP Monitor and the VIDEO or AUDIOVISUALS output jacks on the camcorder. {Note: For beater video, use an VIDEO cable } Note » Please be sure fo mach the color coded input terminals and cable jacks. Viewing Tapes 1. Turn on your PDP Monitor. 2.
9/5/05 8:51 AM Page 18 [1 Connecting a DVD Player (480i, 480p) Playing DVD PDP Monitor Rear Panel Power cord Component cable Audio cable ] Connect the Y. 2, P COMPONENT, 2) input jacks on he PDP Mari tar o the ¥, Fa Ps output jacks on the DVD player using a component cable. 2 Connect the AUDIO 1L/R [COMPONENT], 2] input jacks on the PDF Monitor fo the AUDIO output jacks on the DVD player using o audio cable. | Note : » Please be sure fo match the color cased input terminals and cable jacks.
BN68-008525-00Eng (002-025) 9/5/05 8:51 AM Le APES Dis LEY Connecting a DTV Receiver (480p, 7205, 1080) This PDP Mo sitar displays the optimum picture in 720p mode. Watching DTV PDP Monitor Rear Panel Power cord Component § cable Audio cable DVI cable 1 Connect the cable or antenna to the antenna input jock on the DTV. Connect the ¥, Ps, Pt [COMPONENT 2) or DVI input ack on the PDP Monitor 19 the DVI output jacks on the DTV receiver using a component or DVI cable.
BN68-008525-00Eng (002-025) 9/5/05 8:51 AM Connecting fo HDMI (High Definition Multimedia Interface) (480p, 720p, 1080i) Watching DTV PDP Monitor Rear Manet Power cord DTV Set-Top Box HDMI cable wee Connect the cable or antenna to the antenna input jack on the DTV. Box using an HDMI cable, Note * Please make sure the HDMI sources power is on before selecting HDMI from the "Source List” on the PDP Monitor. To Watch DTV: 1. Turn on your POP Monitor. 2. Turn on your DTV receiver.
9/5/05 §:51 AM Page 21. MA Connecting fo DVI Compatible PDP Monitor Rear Panel [J (480p, 720p, 1080i) By inputting « high-bandwidth digital content protection High-Definition picture source to tha DVI input jack on the FDP Monitor, High Definition pictures can be displayed on the screen in their digital form. Power cord From cable DVI cable or Antenna Audio cable pane | Honestest the DVI AUDIO, input cask on the PDF Monitor with tho AUDIO output jocks on the Set Top Box using an audio cable.
9/5/05 8:51 AM Page 22 [7 Connecting a Digital Audio System There are many Types of digital audio systems on the market today. A simplified illustration of an audio system is shown below. For mots information, see your audio system owner's manual. PDP Monitor Rear Panel Power cord Digital Audio System [ooo] Coaxial cable Colic cable § 1 If your audio system has a coaxial digital audio input, connect ta the “COAXIAL” output jock on the PDP Monitor.
| BN68-00852B-008ng{ 002-025) 9/5/05 8:51 AM Page 23 PDP Monitor Rear Panel ° Loews Power cord The “AY QUT [AUDIO L/R}” terminals cannot be used for external speakers, You must hook them up to an amplifier.
24 | BN68-00852B-00Eng (002-025) 9/5/05 8:51 AM Page Connecting fo a Sub woofer Speaker PDP Monitor Rear Panel lo Power cord Powered Sub woofer > [Option) Passive Sub woofer [Option] » Cu g srl 1 Connect a powered sub woofer to the Sub Woofer jack on the PDP Monitor using the sub woofer cable. To use a passive subaltern, connect an amplifier and uso ironing o he connection procedures described in "Connecting to an Ana lag Amplifier”. Note + Powered sub woofer: This is a suborder with a builtin amplifier.
BN68-008528-00Eng (002-025) 8/5/05 8:51 AM Page 2 PLASMA DISPLAY PANEL Operation Turning the PDP Monitor On and OFF. Plug & Play Feature Setting Up Your Remote Control Viewing an External Signal Source .
BONG-00852B-00Bng (026-035) 9/5/05 9:42 AM Page 26, [2] Turning the PDP Monitor On and Off Turning the PDP Monitor On and Off Press the POWER button on the remote control. The PDP Monitor will be turned on and you will be able so use its features. You can also use the Power bunion on the front of the PDP Monitor. «If your PDP Monitor isn't turned on when the power button is pressed: Press the MODE button fo check if the PDP Mani tor mode has been chosen {BEET 2).
BN68-008528-00Eng (026-035) 9/5/05 8:52 AM Page 27, Displaying Status Information Press the INFO button on the remote control. The PDP Monitor will display the Picture mode, Sound mode, and Clock, + Dynamic pe Ea + Tho INFO window automatically disappears after a few seconds. Press the INFO button once fo manually close the window.
28 | BANES-008528-00Eng (026-035) 8/5/05 8:52 AM Page 28, (hanging Channels Using the Channel Buttons Tress the bunion to change channels. When you press the button, the TV changes channels in sequence. You will see aff the channels that the TV has memorized {The TV must have memorized at least three channels} You will not see channels that were either erased or not memorized. Directly Accessing Channels Press the number buttons fo go direct fo a channel.
BANE-0085ZB-00Eng (026-035) 9/5/05 9:38 AM Page 29, , ©] Plug & Play Feature When the PDP Monitor is initially powered On, basic customer filings proceed automatically and subsequently: Set ling the language and time. Note «The Plug & Play function operates after plugging in the PDP Monitor for the first time. If the television is in Standby made, press the POWER YT T futon on the rem corolla The message “Press ENTER fo start.” is displayed. [ETE Press the ENTER button io select Start.
9/5/05 8:52 AM Page 30. age 30. 30 To reset this feature... Press the MENU button. Press the A or ¥ bunion fo select 1 “Setup”, then press the ENTER bunion. FTE Er Time Fugue Seen Melody Color Weakness Pe] 2 Press the ENTER buffoon to select “Plug & Play”. For further details on sifting up options, refer ta the 3 previous peg. Note * Plug and Play can only be accessed in the TV mess.
9/5/05 8:52 AM Page 3% Lessie Display) [2] Setting Up Your Remote Control Your PDP Tonier comes equipped with a universal remits control. In addition to controlling the PDP Monitor, the universal remote control can loos operate a VCR, Cable bax, DVD, and some Samsung Set top boxes {even if your VCR, Cable box and DVD are made by manufacturers other than Samsung). Note : » The remote control might not be compatible with ali DVD Players, VCR, Cable boxes, and Set Top Boxes.
HEB-00852B-00Eng (026-033) 32 9/5/05 8:52 AM Page 32, Remote Control Codes VCR Codes Brand Brand Codes | Brand Codes. 026 037 041 054 056 006 018 620 031 024.075 079 034 018 036. ‘Admiral : G57 B08 B76 U1 626037 A Aida ¢ Vandyke 007 008 018 026 037 | 017 019 002 021 035 041 043 S7 068 Aka 027004032 | KLH 070 | “Samsung 000 001 002053 04 005 Audio Dynamics B07D26 | Loyd 075 | Sanguine 036 Belittlement 018 | Login LL G8 | Sonya Bigots Bronson 027 | 1x1 025 | Scott 093 037 052 067 Candle 002.
(026-035) 9/5/05 8:52 AM Page 33 PEE Display [2] Viewing an External Signal Source Use the remote control to switch between viewing signals from connected equipment, such as VCR, DVD, and the Set Top Box source. Setting the Signed Source Press the MENU button. 1 Press the ENTER button fo select “Input”. > Quick way fo accosts viewing on external signal source © Just press “SOURCE” button on the remote control. 2 Press the ENTER bunion fo select “Source List”.
BONE-008528-00Eng (026-035) 9/5/05 8:52 AM Page 3%, 34 Assigning Names to External input mode 1 Press the MENU button. Press the ENTER button to select “Input”. 2 Press the A or ¥ bunion fo select “Edit Name”, then press the ENTER bunion. 3 Press the ENTER button. Press the & or '¥ button fo select external device, then press the ENTER button, o You can select the VCR, DVD, Cable STB, HD STB, Satellite STB, AY Receiver, DVD Receiver, Game, Camcorder, DYD Combo, DHR {DVD HDD Recorder) or PC.
9/5/05 8:52 aM Page 35 PLASMA DISPLAY PANEL Picture Control Changing the Picture Standard Customizing the Picture Fingerings Viewing the Dale Demonstration Changing the Screen Size . Viewing the Picturesqueness.
9/5/05 8:55 AM Page 35 36 Changing the Picture Standard You can select the type of picture which best corresponds to your viewing requirements. Press tha MENU button. Press the 4 or ¥ button fo select 1 “Picture”, then press the ENTER bun. NS hg = (juice way to ace ass he picture doting: Just press “MODE” button p fol " _— on tha remote control. Fi [i [LIEN 2 Press the ENTER bunion again fo select “Mode”. rE Lr [er Cross the ENTER button.
9/5/05 8:55 AM Page 37, You con use the onscreen menus to change the “Contrast”, “Brightness”, “Sharpness”, “Color”, “Tint*, and “Carol Tone” according fo personal preference. You can select “Standard” which automatically recalls your personalized picture seeings. Crass the MENU button. Press the & or ¥ bunion fo select 1 “Picture”, then press the ENTER button. 2 Press the ENTER button again fo select “Custom”. Pres [ ic Press the ENTER bunion.
BONE-D0852B-008ng (036-051) 9/5/05 8:55 AM Page 38 | r Press the ENTER button to return to “Picture” menu. Y . Press the 4 or ¥ button to select “Color Tone”, then ea press the ENTER button ELE zl ET) IES [AI [2 LE ROGET Press the A ar ¥ bunion fo select @ particular option 6 {Cool, Cool, Normal, Warm, or Warm, then press the ENTER bunion. Press the EXIT button to exit.
BN6B-00852B-D0Eng (036-051) 9/5/05 8:55 AM Page Viewing the Dale Demonstration This PDP Monitor includes the Dale function so as to provide a high visual quality. If you set Dale Demo to On, you can view the applied Dells and normal pictures on the screen, for demonstration purposes. Using this function, you can view the difference in the visual quality. Press the MENU button. Press the A or '¥ button fo select 1 “Picture”, then press the ENTER bunion.
5/5/05 8:55 AM Page AD 40 Screen size selection depends on the type of video input Press the MENU button. Press the A or ¥ bunion fo 1 defect “Picture”, then press the ENTER button. 2 Quick way fo change the Screen size Just prods “SIZE” bunion under the cover of the reemerge control. Changing the Screen Size Wy Co tar Control Fim Mode ATE Press the A or ¥ bunion fo select “Size”, then press the 2 ENTER bunion. Press the A or ¥ button fo select the screen size you want, then press the ENTER bunion.
BN68-00852B-00Eng (036-051) 9/5/05 8:55 AM Page 41 When you press the SIZE button on the cremate control, the PDP Monitor's screen made should appear in sequence. The screen displays in this order: 16:9, 4:3. 16:9 43 Sets the picture to 16:9 wide mode. Eels the picture to 4:3 normal mode, oOo @) O Zoom Magnifies the size of the picture on the screen.
9/5/05 8:55 AH Page 42, Viewing the Picture-in-Picture Selecting the PIP Screen Press the MENU button. Press the A or ¥ button fo select 1 “PIP”, then press the ENTER bunion. Dw Duffer wo do access the BP mode: Jose press “FIP” button under the cover of the remit control. 2 Press the ENTER button again fo select “Mode”. Press the ENTER button, then press the & or ¥ bunion to select “On”. The PIP image will appear in the corner of the screen.
| BN68-00852B-00Eng (036-051) 9/5/05 8:55 AM Page Selecting an External Sign! You can use PIP to view a signal from an external source, such as o VCR. Sek the FIP Mods to On. [Refer to gaps 42) Press the MENU bunion. Press the 4 or '¥ annuitant fo select 1 “PIP”, then press the ENTER bunion. Press the A or ¥ bunion fo select “Source”, then press 2 the ENTER bunion.
9/5/05 9:52 AM Page 44, 44 Swapping the Contents of the PIP and Main Image Set the PIP Mode to On. {Refer to page 42) Press the MENU button. Press the A or ¥ button to select 1 “PIP*, then press the ENTER bunion. por [AN > Quick way lo sang the size of the PI window Just press SWAP" ne button nds the cover of the remote control. Nouns LP Press the A or '¥ bunion to select “Swap”, then press the ENTER bunion. = The image in the PIP window will appear on the main screen, and vice versa.
8/5/05 95:52 AM Page 45 | Changing the Size of the PIP Window Sef the PIP Mode to On, [Refer to page 42) Press the MENU button. Press the A or ¥ bunion fo select 1 "PIP", then press the ENTER bunion. = {muck way Io Shebangs the size of the PIP window : Just press “SIZE” button under the caver of the remote control. Press the A or ¥ button fa select “Size”, then press the ENTER bunion.
3/5/05 8:35 RM Page 46 46 Changing the Location of the PIP Image Set the PIP Mode to On. (Refer ta page 42) Press the MENU button. Press the 4. or ¥ burn to select 1 “PIP, then press the ENTER button. fo ree Er Ea Press the A or ¥ button fo select “Position”, then pass the ENTER button. Press the A or ¥ button Io select the PIP position {[8] you wont, then press the ENTER bunion. 4 Press the EXIT button fo exit. * In CD ond (1 modes, Position cannot be selected. Source pe.
9/5/05 8:55 AM Page 47 Changing the PIP Sound Select Set the PIP Mode lo On. [Refer fo page 42) 1 2 Press the MENU button. Press the A or ¥ button fo select REIN “PIP“, then press the ENTER button. Press the A or ¥ bunion to select "Sound Select, then press the ENTER button. Press the A or ¥ bunion fo select “Main” or “Sub”, then press the ENTER button. Press the EXIT button to exit.
| BN68-008528-00Eng (036-051) 9/5/05 Bib AM Page 4% <7 [9] Setting the My Color Control Mode My Color Control allows you to adjust colors according to your preference, by adjusting skin, sky, and grass tones using the predefined fingerings (Pink, White, Standard, Custom, Red, Green, Blu, Yellow] without affecting other colors on the screen Using the My Color Control Function in the Busy Control Menu Skin, sky and grass tones are easily adjustable o suit your preferences. Press the MENU button.
BONG-000523-00En3 (036-051) 9/5/05 £155 AM Page Color Control Mode Characteristics Using My Color Control mode, you can enjoy vivid colors as shown below. Dw Emphasizes Warm Skin Molars. 2» Emphasizes Reds. >» Emphasizes Yellows. Note >» Emphasizes Wil Greens. > Standard Pics. I» Emphasizes eur Bliss. * Images shown above may differ farm the actual adjustment on the screen. These images are presented for illustrative purposes.
BN6B-00852B-00Ena (036-051) 9/5/05 8:55 AM rage 50. My Color Central Custom Settings Users can adjust the 6 My Carol Control colors (Red, Green, Blue, Yellow, Pink and White]. (Gr Re no Tow pe | Press the MENU bunion. Press the 4 or ¥ button to select MARRIAGEABILITY HRT 7 1 “Picture”, then press the ENTER bunion. fact Ey [ok Noel Deon Rl Cae Press the A or ¥ bunion lo select "My Color Control”, then press the ENTER bunion.
BANGS-00852B-008ng (036-058) 9/5/05 8:55 AM Page 51 Press the A or ¥ bunion to select “Reset”, then press the 6 ENTER bunion. The previously adjusted My Color Central Colors will be reset fo the factory defaults. [2 Blue Press the EXIT bunion lo exit.
BN68-00852B-00Eng (052-061) 9/5/05 8:58 An Page 52, [9] Setting the Film Mode When a video input source is from a Film such as movies, this feature identifies the source ond changes fo the corresponding screen. Press the MENU bunion, Press the A or ¥ bunion to hued 1 select “Picture”, then press the ENTER button, fo.
BN68-00852B-00Eng (052-061) 9/5/05 8:58 AM Page PLASMA bis Play PANEL Sound Control Customizing the Sound .. Using Automatic Sound Settings Setting the Sensurround XT Setting up Doss [Digital Natural Sound engine). Using the Auto Volume... Safariing the On/ON Melody Selecting the Internal Mute Setting up the Sub Woofer Output.
| 9/5/05 8:58 AM Page 54 Customizing the Sound The sound settings con be adjusted fo suit your personal preferences. {Alternatively, you can use one of the “automatic” settings. See next page.) “Sound”, then press the ENTER bunion. Mode EEE fap Crass the A or '¥ bottom to select “Equalizer”, then ? press the ENTER button, Press the «4 or Pollution fo select particular frequency 3 to adjust. Press the & or ¥ bunion to increase or decrease the level of the particular frequency.
9/5/05 B:58 ris omit Using Automatic Sound Settings Your PDP Monitor has automatic sound seedlings (*Standard, “Music”, “Movie”, and “Speech} that are preset af the factory. Or, you can select “Custom,” which automatically recalls your personalized sound slings. 1 Press the MENU bunion.
BIG-00852B-00Eng (052-061) 9/5/05 8:58 AM Page 56, Sensurround XT is o patented SRS technology that solves the problem of playing 5.1 multichannel content over hwo speakers. Sensurround delivers a compelling, virtual surround sound experience through any two-speaker playback system, including internal television speakers. It is fully compatible with all multichannel formats. Press the MENU bunion. Press the 4 or ¥ button to select 1 “Sound”, then press the ENTER bunion.
9/5/05 8:58 aM Page 57, Sleepless Display Dense (Digital Natural Sound engine) Dense encases the sound quality, automatically controls output, and prevents sound distortion. Press the MENU bunion. Press the 4 or ¥ button to select 1 “Sound”, then press the ENTER button. LUA L Internal Mute LE ry REY 2 Press the A or ¥ button to select “Dense, then press the ENTER button. Ee BRC HE] > ELT. Press the ENTER button to select "Speaker Equalizer” or 3 “DRACO, then press the ENTER bunion.
BONG-008528-00Eng 9/5/05 8:58 AM Page Press the MENU button. Press the & or ¥ button Io select Using the Auto Volume Each broadcasting station has its own signal conditions, which can mike i necessary fo adjust the volume vary time the channel is changed. "Alta Volume” lets you automatically adjust the volume of the desired channel by lowering the sound output when the modulation signal is high or by raising the sound output when the modulation signal is low.
9/5/05 8:58 AM Page 1 2 Setting the On/Off Melody A melody sound can be sel to come on when the PDP Monitor is powered on or off. Press the MENU button. Press the & or ¥ button to select “Setup”, then press the ENTER button, Press the A or ¥ bunion ta select “Melody”, then press the ENTER bunion hs [SUE LE [el TEE Energy Saving 5 Standard MLL Ld [rey Time ERY [Olga t Energy Saving AM Press the A or ¥ bunion to select “Of or “On”, then press the ENTER bunion. « The default value is "On".
BONG-00852B-00Eng (052-061) 9/5/05 8:58 AM Page Selecting the Internal Mute Sound output from the PDP Monitor speakers is muted. Press the MENU bunion. Press the & or ¥ button to select 1 “Sound”, then press the ENTER bunion. = ERT) 2 ac 211 Fr re Sub Woofer Press the A or ¥ button to select “Internal Mute”, then 2 press the ENTER button. fe * Custom al Eta ER. lH prs pre Press the A or ¥ button fo select “On”, then press the = = 3 ENTER button.
| BONE-00852R-00Eng (052061) 9/5/65 8:58 AM Page 61, | Setting up the Sub Woofer Output After connecting @ Sub Woofer Speaker (sold separately}, you may set the activation, volume or cutoff frequency. Press the MENU button. Press the A or ¥ button lo select 1 “Sound”, then press the ENTER button. z Custom sews Sub Woofer hE) Press the A or ¥ button to select "Sub Woofer, then 2 press the ENTER button. Press the ENTER button. Press the 4 or ¥ button fo select 3 “On”, then press the ENTER bunion.
BN66-00852B-00ERg (062-077) 9/5/05 8:59 AM Page §3 PLASMA DISPLAY Connecting a PC and Operation Connecting a PC...
BONG-00852B-00ERg (062-077) 9/5/05 9:38 AM Page 64 Connecting a PC Connection to o Macintosh computer may require an stapler. PDP Monitor Rear Panel pa ee ETT 69 0 8 Roe 6 oon 6 Sw sos fife BoE a 8) Power cord Audio cable | Comet a PC cable between the FC Pulp jack on the FC ond the RGB input ack (FC IN) on the PDP Monitor. ; ? Connect a Audi cable between the Audi jack on the PC and the Audio input jacks [AUDIO] on the i PDP Monitor.
EN-00852B-00Eng (062-077) 9/5/05 8:59 AM Page £5 Setting up Your PDP Monitor {Plug and Play) Our adoption of the new VESA® Plug and Play solution eliminates complicated and dime consuming setup. b allows you fo install your monitor in a Log and Play compatible system, without the usual setup hassles and confusion. Your PC system can easily identify and configure itself for use with your PDP Monitor.
| BNG68-008525-00Eng (062-077) 9/5/05 8:59 AM Page How fo Set up Your PC Software (Windows only) The Windows display-settings for o typical computer are shown below. But the actual screens on your PC will probably be different, depending upon your particular version of Windows and your particular video card. But even if your actual screens Ink different, the same, basic setup information will apply in almost ofl cases. {if not, contact your computer manufacturer or Samsung Deals} ; 1.
| BN68-DO8S52B-00ENg (062-077) 9/5/05 8:59 AM Page 67 ne Display Notes Both screen position and size will vary, depending on the type of PC monitor and iis resolution. The table below shows oll of the display modes that are supported: Video Signal Resorption Vertical Horizontal Vertical | Horizontal {Dot X line] Frequency] | Frequencies | Polarity Polarity 640% 350 70 31s N F 720% 400 70 315 ? N VGA 640% 480 375 N N 56 351 P/N P/N 0 379 ’ p VGA 800 X 600 = ron 484 N N GA 1024X 788 70 56.
| BONG-00852B-00Eng (062-077) 9/5/05 8:59 AM Page 68 Changing the Position of the Image After connecting the PDP Monitor to your PC, adjust the position of the seen if if is not well-deigned. Preset: * Press the SOURCE button to select "PC." Crass the MENU button. Press the 4 or ¥ button to select 1 “Setup”, then press the ENTER button. BEE Time Sle Seen : Off prey Re ARCS Er RE) A] Press the 4 or ¥ bunion to select “PC”, then press the wt 2 ENTER button.
9/5/05 8:59 AM Page 69 Picture Quality Adjustment Picture Automatic Adjustment Preset: » Press the SOURCE button to select "PC". Press the MENU button. Press the A ar ¥ bunion la select 1 “Setup”, then press the ENTER button. Language Energy Saving ENTER button. [EE . Position Cy oun ET Sr 2 Press the A or '¥ bunion to select “PC”, then press the Press the A or ¥ button to select “Auto Adjustment”, 3 hen press the ENTER button, The message "Auto Adjustment in progress. Please wait.
9/5/05 8:59 AM Page 70, 70 Coarse Adjustment Preset: » Press the SOURCE bunion to select “PC”, Press the MENU button. Press the A or ¥ button to select 1 “Setup”, then press the ENTER bunion. [TYE Melody RI Energy Siva ENTER bunion. ’ Position 2 Press the A or ¥ button to select “PC”, then press the aC | EEN ryt 3 Press the ENTER button to select “Image Lock”. Press the ENTER buffoon again to select “Coarse”. 4 Remove picture noise {vertical stripes} on the screen by pressing the €or ® button.
BN68-00852B-00Eng (062-077) 9/5/05 8:59 AM Page 71 ding Tuning {Fine} Preset: * Press the SOURCE button to select “PC”. Press the MENU button. Press the A or ¥ button fo select 1 “Setup thees press the ENTER bun, [TTT BTS Time Lg Bd Melody EY Color Weariness PL EC Ea Press the A or ¥ bunion fo select "FC", then press the 2 ENTER bun [Ev Auto Adjustment 3 Press the ENTER button to select “Image Lock”. Press the A or ¥ button to select “Fine”, then press the 4 ENTER button.
BN68-008528-00Eng (062-077) 9/5/05 9:00 AM Page Image Reset Preset: Press the SOURCE button fo select “PC”. 1 Press the MENU button. Press the A or '¥ button fa select “Setup”, then press the ENTER bunion Ti ETT EE hi [re off PY [Rl Press the A or ¥ bunion fo select “PC”, then press the ENTER button. [ras a ITE [Err Press the A or '¥ button fo select “Image Reset’, then press the ENTER bereft. The message “Image reset is completed.” appears on the scream.
= + 9/5/05 9:00 AM Page 7 PLASMA DISPLAY PANEL Time Setting Meting the Clock ores Hefting the Sleep Timer Setting the On/Off Time
| BN6B-00852B-00ENg (062-077) 9/5/05 5:00 AH Page Setting the Clock Rafting the clock is necessary in order fo use the various timer features of the PDP Monitor. Also, you can check the time while watching the PDP Monitor. {Just press the INFO button} Press the MENU bunion. Press the & or ¥ bunion fo select 1 “Setup”, then press the ENTER button. Press the A or ¥ button fo select “Time”, then press the wii] 2 ENTER button.
BN68-00852B-00ENg (062-077) 8/5/05 9:55 AM Page Setting the Sleep Timer The sleep dimer automatically shuts off the PDP Monitor after a preset time {from 30 to 180 minutes]. Press the MENU hut ion. Press the A or ¥ button fo select 1 “Setup”, then press the ENTER button. . . . EIT > Quick way fa access tho sleep fim setting: Jest poss “SLEEP” button Go on the resole contra. Carol Weakness Energy Saving + Standard hE Press the A or ¥ bunion fo select “Time”, then press the 2? ENTER bunion.
9/5/05 9:00 AM Rage 7% 76 1 Press the MENU button. Crass the A or ¥ bunion to select “Setup”, then press the ENTER button. ENTER button. 2 Press the A or ¥ button to select “Time”, then press the Crass the A or ¥ button to select "On Timer”, then press the ENTER button. Press the A or ¥ bunion to adjust “Hour”, then press the » button to move to the next step. Set other items using the same method as above.
BHAJI-008528-00Eng (062-077) 9/5/05 2:00 BM Page PLASMA DISPLAY PANEL Function Description on Selecting a Men Language 78 Digital Noise Reduction . Setting the Blue Screen .. Using the Color Weakness Enhancement Option Using the Energy Saving Feature Preventing Screen Bunin Reducing the Effects of Screen Burn... Setting the MDC [Multiple Display Control].
ENG-008528-00Eng (078-085) 9/5/05 9:01 AM Page 7%, Selecting a Menu Language Press the MENU button. Press the A or ¥ bunion to select SE a 1 “Setup”, then press the ENTER bunion. Pr i ag EIT HE Press the 4 or ¥ bunion fo select “Language”, then press 2? the ENTER button Te] language RL pI Free Leg J Se] ¥ More Press the & or ¥ bunion fo select the appropriate 3 language: “English”, “Francois” or “Espalier. Tongue Press the ENTER button. 3 jin [chill ET LE [en EEA NE ALY A Press the EXIT button fo exit.
1 BONG-00852B-00Eng (078-085) 9/5/05 9:01 AM Page J Sleepless Display Digital Noise Reduction If the broadest signal received by your PDP Monitor is weak, you can activate the Digital Noise Reduction feature to help reduce any static and ghosting that may appear on the screen. | 1 Crass the MENU button. Press the A or ¥ button fo select 1 “Picture”, then press the ENTER button.
BN68-00852B-00Eng (078-085) 9/5/05 9:01 AM Page Setting the Blue Screen (tna signal is being received or the signal is very weak, a blue screen automatically replaces the noisy picture background. If you wish to continue viewing the poor picture, you must set the "Blue Screen” mode 10 “OF”. Press the MENU bunion. Press the A or ¥ bunion fo select 1 “Setup”, then press the ENTER button. Color Weakness Energy Sang h Press the 4 or ¥ button lo select "Blue Screen”, then 2 press the ENTER button.
(078-085) 9/5/05 9:01 AM Page 81 Im | Using the Color Weakness Enhancement Option his option adjusts the Red, Blue or Green color Io enhance the image according to the user's i ge particular color weakness. Press the MENU bunion. Press the A or '¥ bunion to select 1 “Setup”, then press the ENTER button. FE Time Press the A or '¥ bunion to select “Color Weakness”, 2 then press the ENTER button, "On, then press the ENTER button. You will also see the items “Red”, “Green”, and “Blue”, 3 Press the ENTER button.
BONG-00852B-00Eng (078-085) 9/5/05 9:57 AN Page 82, Using the Energy Saving Feature This feature adjusts the screen brightness automatically depending on the surrounding lighting conditions. Press the MENU button. Press the A or ¥ button to select 1 “Setup”, then press the ENTER bunion. 2» Quick way 1o select Energy Saving: Jul press “ESAVING® bunion under the cover of fhe remote contra). Color Weakness EE MARA] Press the A or ¥ button fo select "Energy Saving”, then 2? press the ENTER bun.
BONG-00852B-00Eng (078-085) 9/5/05 Preventing 9:01 aM Page 83, le Display Soon Burned 1 To reduce the possibility of screen bum, this unit is equipped with screen burn prevention technology. This technology enables you to set picture movement up/down {Vertical Line} and side to side {Horizontal Doll. The Time setting allows you to program the dime between movement of the picture in minutes. Press the MENU button. Press the A or ¥ button fo select “Setup”, then press the ENTER button.
| BN68-00852B-00Eng (078-085) 8/5/05 9:01 AM Page @4, Reducing the Effects of Screen Burn If screen burn has accursed, you can select a white screen or signal pattern {rolling screen) fo help remove screen burn artifacts. Press the MENU bunion. 1 Press the 4 or ¥ bunion ta select “Setup”, then press the ENTER button. [FED T Time [ foes Color Weakness EEE) Press the A or ¥ button to select “Screen Burn 2 Protection”, then press the ENTER bunion.
BOBBIN-00832B-00Eng{ 078-085) 9/5/05 9:01 AM Page £5 7] San the MDC Moll isle Control This function enables you to easily control the connected monitors on the PC by specifying (Ds to connected monitors. Press the MENU bunion, 1 Press the 4 or '¥ button to select “Setup”, then press REEL the ENTER bunion. mage ry re Rad Melody Press the A or ¥ bunion to select “Multi Control”, then 2 press the ENTER bunion. the ENTER button. " Select the ID setup number hy pressing the A, ¥ or [yey numeric buttons.
BONG-008528-00Eng (086-031) 5/5/05 9:02 AM Page Troubleshooting If the PDP Monitor seems to have e problem, first try this fist of possible problems and solutions. If none of these troubleshooting tips apply, then call your nearest service center. Problem Possible Solution Poor picture. Hack all wire connections. No picture or sound. Press the SOURCE button. Nike sure fhe PDP Monitor is plugged in. Chock tho the Mute feature is OF Check if Internal Mute is sat to On. Poor sound quality. Adjust the volume.
BN68-00852B-00Eng (086-091) 9/5/05 9:02 AM Page 89, Ee {Lessie Dis play [7] Care and Maintenance With proper care, your PDP Monitor will give you many years of service. Please follow these guidelines to get the maximum performance from your PDP Monitor, Identifying Problems + Do not put the PDP Monitor near extremely hot, cold, humid or dusty places. * Do not put the PDP Monitor near appliances that create magnetic fields. * Keep the ventilation openings clear.
| BN68-00852B-00ENG (086-091) 3/5/05 9:02 BM Page 890 [7] Specifications Exterior design and product specifications are subject to change without prior notice to improve the performance of this product. Mode! HP-R8082 Dimensions | Display 48.43 |W] x 32.52 [H) x 3.72 (Dj inches [Without Stand} 48.43 (W) x 34.47 (4) x 13.18 [D] inches {With Stand} Weight | Display 46.8 Kg / 103.17 Ibs (Without Stand) 53.5 Kg / 117.
