FCC RF Radiation Exposure Statement ---------------------------------------------------The antenna(s) used for this transmitter must be installed to provide a separation distanc e of at least 20 c m from all persons and must not be co- loc ated or operating in c onjunc tion with any other antenna or transmitter.
SAFETY CONCERNS For product safety and correct operation, the following information must be given to the operator/user and shall be read before the installation and operation. Conventions Warning This paragraph contains safety instructions that users must follow in order to avoid This icon indicates a general caution. personal injuries.
WAP-701 User Guide Warning Warning Be careful not to drop the product. This is to prevent product damage. Do not install the product in a humid or dusty area. This is to prevent electrocution and fire. Do not install the product near heating apparatus (e.g. heater and cigarette fire). Do not use or keep combustible sprays or flammable objects near this product. This is to prevent electrocution and fire. This is to prevent electrocution and fire.
WAP-701 User Guide Do not place water cups, chemicals, or metals above the product. This is to prevent electrocution and fire. Do not pull or excessively bend the power cord, and do not use damaged power cables or loose sockets. Do not touch the plug with wet hands. This is to prevent electrocution and fire. This is to prevent electrocution and fire.
WAP-701 User Guide Insert the power plug fully and firmly into the outlet. This is to prevent electrocution and fire. If the product makes strange sound, smell, or smoke, unplug the power cable immediately and contact the service center. This is to prevent electrocution and fire. Unplug the power cable when not using the product for a long time. This is to prevent electrocution and fire.
WAP-701 User Guide Caution Caution Do not install the product under direct sunlight. Do not place heavy objects on top of the product. This is to prevent parts of the This is to prevent product product from being damage. damaged. Do not clean the product with chemicals such as wax, benzene, alcohol, thinner, insecticide, air freshener, lubricant, and detergent. Do not disassemble, repair or Doing so may discolor or damage the product.
WAP-701 User Guide Please use the product properly according to the user manual. This is to prevent malfunctions or a decrease in life span. The power adaptor must be connected to a AC 220 V outlet. And the socket-oulet shall be installed near the equipment and shall be easily accessible. Clean the product with a dry cloth after unplugging the power cord. This is to prevent product damage.
Table of Contents SAFETY CONCERNS 1 Bottom View........................................... 18 Side View .............................................. 19 Conventions ............................................................ 1 Warning .................................................................... 2 Caution...................................................................... 5 Things You Should Know 8 Installation 20 Installing WAP-701.............................................
Things You Should Know What is a Wireless LAN (WLAN) Repeater? Power of signals generated from an WLAN Access Point (AP) decreases as the signals reach further distances. To extend the transmission distance without attenuation of power, the frequency must be regenerated or the power must be increased by a separate device. A WLAN repeater is a device that regenerates and relays transmitted signals.
WAP-701 User Guide WAP-701 Functions and Installation Environment WAP-701 is a wireless repeater that can be used for constructing a wireless network or as a wireless AP. Installed inside a cell area of an AP or repeater, the WAP-701 retransmits data received from wireless terminals, such as lap tops and wireless PDAs, located outside the cell area of a neighboring AP, to the AP.
WAP-701 User Guide Selecting Location of Installation The configuration of wireless cells must be determined in order to decide the installation location of WAP701. Cell areas are affected by surrounding obstacles such as outer walls, windows and pillars of a building. Therefore, the product should not be installed in an area isolated from the surrounding environment, such as inside of a communication room or in a enclosed location.
WAP-701 User Guide WAP-701 Specification Category Specification Model Name WAP-701 Power AC 100 V ~ 240 V (50Hz ~ 60Hz) Size 115h x 60w x 35d (mm) Weight 148 g or less Temperature (℃) Operating Temperature : 0~40 ℃ Storage Temperature : -20~70 ℃ Humidity (%) 0~90 % Wireless Interface Standard IEEE 802.11b/g Frequency Bandwidth IEEE 802.11b/g : 2412~2472 MHz Modulation IEEE 802.11b : CCK IEEE 802.11g : OFDM Transfer Rate IEEE 802.11b : 1/2/5.5/11 Mbps IEEE 802.
Preparation Main Function WLAN Access WAP-701 provides a WLAN interface in accordance with the IEEE 802.11b/g standard, and can connect to wireless terminals that support this standard. Security WAP-701 supports Wired Equivalent Protocol (WEP) and WiFi Protected Access (WPA) encryption schemes for WLAN security. WAP-701 supports 64/128/152 bit key encryption for WEP, which conforms to the IEEE 802.11b/g standard. WPA supports an authentication scheme that satisfies Pre-Shared Key (PSK) and IEEE 802.
WAP-701 User Guide that supports this standard. WAP-701 can also perform Logical Link Control/Subnetwork Access Protocol (LLC/SNAP) functions when necessary. Bridge WAP-701 provides a IEEE 802.11D standard bridge function, which connects WLAN and Ethernet. MAC addresses of wireless terminals and Ethernet terminals can be registered to each port and updated every 5 seconds.
WAP-701 User Guide needs to receive an IP address from a DHCP server located outside the subnet of the mobile unit, WAP701 enables the mobile unit to receive the IP address by performing DHCP server or Relay Agent function. Auto Channel Selection WAP-701 can automatically select a channel that has the least frequency interference. Transmission Power Control WAP-701 supports transmission power control to enable efficient WLAN design.
WAP-701 User Guide Management WAP-701 can be managed remotely through a remote server supporting SNMP standard or through the built-in WEB server function. Management through Remote Server WAP-701 can be managed from a remote server (Network Management Server: NMS) that supports SNMP standard. WAP-701 supports MIB I, II, 802.11 MIB standard. Management through WEB Server WAP-701contains a WEB server function that can be used for managing status and configuring functions through the WEB server connection.
WAP-701 User Guide relation with TOS/DSCP and the priority of a mobile unit based on the MAC Address. Easy Software Upgrade Users can easily upgrade the WAP-701 software by downloading firmware through the FTP server or TFTP client. Additional Functions MAC Filtering and NAT are provided as additional functions. MAC Filtering You can enable or disable service for a terminal whose MAC address is registered to WAP-701.
WAP-701 User Guide Shape Front View Plug-In Type Cable Type 17
WAP-701 User Guide Bottom View Plug-In Type Cable Type 18
WAP-701 User Guide Side View Plug-In Type Cable Type 19
Installation This section describes the procedure for installing WAP-701. Installing WAP-701 Install WAP-701 according to the following procedure: 1. Install and power the product according to the product type as described below: Plug-In Type Insert the power plug on the rear panel of WAP-701 into a 220V outlet.
WAP-701 User Guide Cable Type To install the product on a wall, refer to the screw location diagram presented in the last chapter of this manual and mark the locations of screws on the wall before installation. Screw location diagram 3. y Configure the network and function through the WEB server. Refer to ‘Function Configuration’ for detailed descriptions on configuring functions.
WAP-701 User Guide WAP-701 Cable Connection Connect the LAN cable and the power adapter as described below: LAN Cable Use a LAN cable to connect the LAN port on the undersurface of the product to a hub or a modem for Internet connection. Use the LAN cable provided with the product or use a RJ-45 LAN cable.
WAP-701 User Guide WAP-701 Antenna Installation Install the antenna as described below: You can install the antenna provided with the product. First, you should open and remove the rubber cap on the product. Then install the antenna. Open the rubber cap Checking WAP-701 LED Status Based on the front view, the left LED lights up when the power is on, and the right LED lights up when a LAN cable is connected.
Troubleshooting This section provides solutions to problems that may occur while using AP. If a problem not metioned in this section occurs, please visit the after-sales service centor or our homepage for assistance. Wireless access to AP is disabled. − First, check the IP address of the AP. The IP address is set to 192.168.111.10 by default but can be changed by users. − Check the SSID of the AP. − Check if the Security function of the AP is enabled by selecting ‘Security’ from the ‘Wireless’ menu.
Bottom Top Screw Location Diagram Cut along this dotted line.
