Specifications

ManualsBrandsSamsung Electronics ManualsElectronicsSmart Control

UNLESS OTHER SPECIFIED TOLERANCES ON

X.X

X.XX

ANGLES

HOLEDIA

INPAQ TECHNOLOGY CO., LTD.

ʳʳ

SCALE

----- UNIT

DRAWN BY:

!"#

!"#!"#

!"#

CHECKED BY:

$%&

$%&$%&

$%&

!"#

!"#!"#

!"#

APPROVED BY:

'()

'()'()

'()

THIS DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF

INPAQ TECHNOLOGY CO.,LTD.AND SHALL NOT BE REPRODUCED OR

USED AS THE BASIS FOR THE MANUFACTURE OR SALE OF

APPARATUS OR DEVICES WITHOUT PERMISSION

DOCUMENT

SPEC REV.

TITLE

ACA-3216-A1-CC-S Specification

NO.

ENS000069320

PAGE

OF 8

ACA-3216-A1-CC-S Specification

1. Features and ApplicationǺ

ǺǺ

This product is for WiFi/BT band

2. Explanation of Part NumberǺ

ǺǺ

A -

3216

S _

(1)

(2)

(3)

(4)

(5)

(6)

(7)

(1) Product Type

ǺChip Antenna

(2) Center Frequency/Band Code

Ǻ2.4 GHz Band

(3) Size Code

Ǻ3.2*1.6 mm (Length * Width)

(4) Design Revision Code

ǺRev.1

(5) Antenna Type

ǺCoupling Ceramics

(6) Special Code

ǺRoHS Compliant

(7) Suffix For Special Requirements

3. Electrical SpecificationǺ

ǺǺ

Item Specification

Frequency Band 2400 ~ 2500 MHz

Polarization Linear

Impedance 50 ohm Typ.

VSWR Less than 2.5

*Peak Gain 0.97 dBi Typ.

*Peak Efficiency 71.1 % Typ.

* Test condition

Test board size 100*50 mm

Matching circuit may be required

Summary of content (8 pages)

PAGE 1
ACA-3216-A1-CC-S Specification 1. Features and ApplicationǺ Ǻ This product is for WiFi/BT band 2. Explanation of Part NumberǺ Ǻ AC (1) A - 3216 (2) (3) A1 (4) - CC (5) S (6) _ (7) (1) Product TypeǺChip Antenna (2) Center Frequency/Band CodeǺ2.4 GHz Band (3) Size CodeǺ3.2*1.6 mm (Length * Width) (4) Design Revision CodeǺRev.1 (5) Antenna TypeǺCoupling Ceramics (6) Special CodeǺRoHS Compliant (7) Suffix For Special Requirements 3.
PAGE 2
4. Physical DimensionǺ Ǻ Top view Bottom view Side view L H W W1 B A L1 L 3.20 ± 0.30 W 1.70 ± 0.20 H 0.50 ± 0.10 A 0.30 ± 0.15 B 0.30 ± 0.15 L1 0.47 ± 0.20 W1 0.70 ± 0.20 (Unit mm) 5. Recommended PCB LayoutΚ Κ Layout Pad Pad (GND) (Feed) 2.4 GHz Feed Line (50 ohm) Pad (GND) Clearnace Area (8.5*6.5 mm) Ground UNLESS OTHER SPECIFIED TOLERANCES ON ! X X.X ANGLES SCALE ----- # ! !"# DESIGNED BY:!"# DRAWN BY: ! X.
PAGE 3
Pad Dimensions on PCB Layout Top View Perspective View (UnitǺmm) * ToleranceǺ±0.05 mm UNLESS OTHER SPECIFIED TOLERANCES ON ! X X.X ANGLES SCALE ----- # ! !"# DESIGNED BY:!"# DRAWN BY: ! X.XX HOLEDIA UNIT mm # $%& APPROVED BY:'() CHECKED BY: #ACA-3216-A1-CC-S Specification TITLE " ! INPAQ TECHNOLOGY CO., LTD.ʳʳ THIS DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF INPAQ TECHNOLOGY CO.,LTD.
PAGE 4
6. Electrical CharacteristicsǺ Ǻ Return Loss Frequency (MHz) VSWR 2400 1.84 2450 1.15 2500 1.99 Ǻ Radiation PatternǺ The Gain pattern is measured in INPAQ’s FAR-field chamber. DUT is placed on the table of rotator, a standard horn antenna and Vector Network Analyzer is used to collect data. 3D Chamber Definition UNLESS OTHER SPECIFIED TOLERANCES ON ! X X.X ANGLES SCALE ----- # ! !"# DESIGNED BY:!"# DRAWN BY: ! X.
PAGE 5
3D Gain Pattern 2450 MHz UNLESS OTHER SPECIFIED TOLERANCES ON ! X X.X ANGLES SCALE ----- # ! !"# DESIGNED BY:!"# DRAWN BY: ! X.XX HOLEDIA UNIT mm # $%& APPROVED BY:'() CHECKED BY: #ACA-3216-A1-CC-S Specification TITLE " ! INPAQ TECHNOLOGY CO., LTD.ʳʳ THIS DRAWINGS AND SPECIFICATIONS ARE THE PROPERTY OF INPAQ TECHNOLOGY CO.,LTD.AND SHALL NOT BE REPRODUCED OR USED AS THE BASIS FOR THE MANUFACTURE OR SALE OF APPARATUS OR DEVICES WITHOUT PERMISSION DOCUMENT NO. SPEC REV.
PAGE 6
7. Taping Package and Label MarkingǺ Ǻ (1) QuantityǺ4000pcs/Reel, T(Thickness of chip)ɩ1.2 (2) Plastic Tape Type 3216 W 8±0.1 A 1.9~2.1 B 3.50~3.60 K Max. 1.40 t 0.22±0.05 F 3.50±0.1 P 4.00±0.1 (Unit: mm) (3) Tape Packing (4) Cover Tape Reel Off Force (5) Reel Dimensions W 8±0.5 12±0.5 A B 178±0.5 13±0.5 178±0.5 13±0.5 (Unit: mm) UNLESS OTHER SPECIFIED TOLERANCES ON ! X X.X ANGLES SCALE ----- # ! !"# DESIGNED BY:!"# DRAWN BY: ! X.
PAGE 7
8. Environmental CharacteristicsǺ Ǻ (1) Reliability Test Item Condition Thermal shock 1. 2. 3. 4. 5. Specification 30±3 minutes at -40°C±5°C, Convert to +105°C (5 minutes) 30±3 minutes at +105°C±5°C, Convert to -40°C (5 minutes) Total 100 continuous cycles No apparent damage Fulfill the electrical spec. after test. 1. Humidity: 85% R.H. 2. Temperature: 85±5°C 3. Time: 1000 hours. No apparent damage Fulfill the electrical spec. after test. 1. Temperature: 150°C±5°C 2. Time: 1000 hours.
PAGE 8
9. Recommended reflow solderingǺ Ǻ (1) Soldering gun procedure Note the follows, in case of using solder gun for replacement. (a) The tip temperature must be less than 350°C for the period within 3 seconds by using soldering gun under 30 W. (b) The soldering gun tip shall not touch this product directly. (2) Soldering volume Note that excess of soldering volume will easily get crack the body of this product. UNLESS OTHER SPECIFIED TOLERANCES ON ! X X.