Using the Battery Your computer uses a smart rechargeable Lithium-ion (Li-ion) battery pack for power when the AC adapter is not attached to an electrical outlet. The smart battery gives a accurate measurement of the current battery capacity which helps extend operating time by enabling effective power management in operating systems that take advantage of the accurate information supplied by the battery.
Safely Using the Battery Follow these guidelines to safely use the battery: • Turn off your computer and unplug it if you accidentally: – Expose the equipment to liquid. – Drop, jar, or damage the computer. • Use only approved battery chargers. • Do not disassemble the battery, heat it above 100°C, or burn it. The battery used in this computer may cause a fire or chemical burn if mistreated. • Your computer's rechargeable battery may be considered hazardous waste.
Installing the Battery To install the battery pack: 1. With the computer’s power off, close the LCD panel and turn the computer over so the bottom of the unit faces up. 2. Slide the battery compartment cover straight up and off the computer. Insert the battery into the battery compartment, ensuring the correct orientation so that the battery fits in its slot properly. 3. Slide the battery pack into the compartment. Make sure the battery is fully inserted into the compartment. 4.
Power Meter The Power Meter displays the charge of the batteries and the current source of computer power, AC or batteries. You may monitor the battery charge or usage by using the “Power Meter”. To access the power meter click icon on the task bar or click Start > Settings > Control Panel > Power Options > Power Meter Tab.
Battery Warnings If the battery charge is low (about 10%) you have approximately 5–10 minutes of battery life left. You should: • Save your work and, • Connect the power cord to the computer or turn off the computer and install a fully charged battery. You can adjust the battery alarm features by using the operating systems power management program (Start > Settings > Control Panel > Power Options > Alarm Tab in Windows).
Using System Setup The System Setup program enables you to configure your computer hardware and set security and power-savings options. The settings you choose are stored in batterymaintained CMOS memory that saves the information even when the computer’s power is turned off. When your computer is turned back on, it is configured with the values found in this memory. Run System Setup if you get a message prompting you to run the program.
Table 6. System Setup Navigation Keys Navigation Key Alternate Key Function Displays the General Help window. Exits the current menu. and keys Keypad arrow keys Select a different menu. Pressing at the Main menu brings you to the Exit menu. and keys Keypad arrow keys Move the cursor up and down between fields. Moves the cursor forward through the cells for a highlighted field.
Changing Booting Priority The Boot menu in System Setup enables you to select the booting device and to set booting options. Boot Device Priority field enables: You to select the order in which the computer attempts to boot from different devices. The field has three (3) options: CD-ROM Drive, Removable Devices and Hard Drive. To change the booting device priority, choose the device positions by completing the following: 1. At startup, press to open System Setup 2.
Using System Security This section describes your computer security programs. The first is the standard BIOS security which is standard on almost all computers. The second is a advanced factory option Biometric security system that uses your fingerprint(s) to control access to your computer and individual files if necessary. You no longer have to worry about passwords being lost, stolen or forgotten.
5. Type a password of up to seven characters. You can enter letters or numbers, but you cannot use the function keys, such as . Your computer does not distinguish between capitalized and lowercase letters in your password. As you type the password, the cursor moves but your password does not appear on the screen. 6. Press after you have typed your password. The computer prompts you to reenter your password for verification. 7. Type your password again and press .
Biometric Security The factory optional fingerprint sensor provides unique security access to your computer. You will no longer have to worry about losing or forgetting your password. Since every person has a unique set of fingerprints, only a biometrically enrolled person may have access to your computer. Advantages of Biometric Security are: • • • • Very high level of security No password to remember, lose or have stolen. Streamlined logon process.
Using Power Management Options Your computer includes Power Management options that can help the battery charge last longer and extend the life of the battery. Power-management options will slow down or shut off system components when the components are not being used. Power management may slow down system performance. Your computer runs fastest with the power cord attached, when power management is disabled. In the next sections, basic and advanced methods of power management will be discussed.
Basic Power Management Schemes This section discusses the basic schemes of power management when the computer is operating on battery power or using AC power. Standby vs. Hibernation Standby unlike hibernation mode does not store unsaved information on your hard disk; it's stored only in the computer memory. If there is an interruption in power, the information is lost. So before putting your computer on standby, you should save your files.
Turning off the monitor and HDDs will save a substantial battery power, therefore when in battery only mode select the shortest time practical. a Hibernate Mode (Power Management or Manual Method) When hibernation is used, your computer turns off and when you power up again, everything is restored exactly as you left it—including programs and documents you may not have saved or closed. Everything in memory gets saved to the HDD, and the monitor and hard disk get turned off.
Advanced Power Management Schemes This section discusses the advanced power management schemes. There are two buttons that you can use to manually conserve power. To enter the power management window complete the following: 1. Click Start > Settings > Control Panel. 2. Click Power Options icon to display the Power Options Properties window. 3. Click the Advanced tab to display the advanced power management options. Advanced Tab Power & Sleep Button Programming Windows 4.
Using the Hard Drive Your computer includes a removable IDE (integrated drive electronics) hard drive. The IDE hard drive can store the data and programs your computer uses. The drive plugs into a connector on the system board. The hard drive that comes with your computer has already been formatted. Do not format the hard drive. Doing so destroys all data contained on the drive.
Installing a Hard Drive To install a hard drive: 1. Remove the old hard drive from the computer as described in the previous section. 2. Slide the new drive into the hard drive compartment. Make sure the drive is pushed back as far as it will go. 3. Install the screw that holds the hard drive in place. 4. If required install windows and appropriate device drivers according to the instructions below.
Video Features and Configuration Your computer includes a TFT LCD or active-matrix display. The capabilities of the screen plus the video drivers installed on the computer determine the quality of the image your LCD can display. The following sections describe the display capabilities of your computer. Resolution and Colour Depth The resolution of the LCD is the sharpness of the image it can display. Resolution is measured by the number of pixels (individual dots) displayed on the entire screen.
Configuring Display Features The following sections describe how to configure the display settings on your computer. Display Resolution Notes: When Windows 2000 is initially installed it will automatically adjust the resolution to maximum available. Changing Colour Depth and Resolution To change the colour depth and resolution of your LCD or external monitor: 1. Click Start > Settings > Control Panel. 2. Click Display icon . The Display Properties window appears. 3. Click the Settings tab.
Using the TV-Out Port Using the TV-out port, a compatible TV or other compatible display device can be connected and an image displayed. No Audio is transmitted through the TV-Out port. To check if and how your TV displays the TV-out signal see the documentation included with your TV. You must also insure that (TV/Video) is changed to Video mode using the TV remote controller or the buttons on the TV set. To enable TV-out: 1. Connect the TV to the TV-Out port using an appropriate cable. 2.
Using Options You can order the following options for your Notebook computer from your authorised reseller: • An extra AC adapter. • An auto adapter that enables you to charge the computer’s battery and operate the computer while in an automobile. • An extra battery pack. • An upgraded hard drive. Optional hard drives are available to fit in the hard drive compartment or the Flex-Bay. • 64, 128, 256 and 512 MB SDRAM memory modules that enable you to upgrade your computer’s memory to a maximum of 1 GB.
Auto Adapter The auto adapter enables you to power your computer and charge the computer battery. • In an automobile, through the +12 volt cigarette lighter socket. To use the adapter: 1. Plug the adapter cable into the AC adapter connector on the computer. 2. Connect the adapter to the cigarette lighter socket. The light on the adapter is green when the adapter is working properly. The light may be red for a few seconds when you first plug in the adapter or while you use the adapter. This is normal.
Battery Pack You can order another smart lithium-ion battery pack for your computer. See “Using Power Management Options” on page 46 for information on the battery. Hard Drives You can order optional hard drives for your system. A hard drive can be installed in the hard-drive compartment to replace your existing hard drive or you can order a hard drive that fits in the Flex-Bay. See “Installing a Hard Drive” on page 51 for information on installing a new drive in the hard-drive compartment.
Installing a Memory Module Handle a memory module carefully. Hold them only by the edges. To install a memory module: 1. Turn the computer over so that the bottom faces up. 2. Using a screwdriver, remove the screw that holds the memory-module compartment door in place. 3. Grasp the edge of the door and pull the door off the chassis. 4. Remove installed modules if necessary: Memory Module Precautions: When removing the module, pull on the plastic portion of the connector slots tabs only.
a. Pull the tabs on the connector slot outward slightly, until the edge of the memory module pops up. b. Hold the memory module by the edges and pull it forward out of the compartment. 5. Align the connector on the memory module with the connector of the slot. 6. Push the memory module into the slot at a slight angle until the connectors are fully engaged. 7. Push down on the edge of the memory module until the module snaps into place. 8.
DVD/CD-RW Combo Drive Module If your system did not ship with a DVD/CD-RW Combo drive included, you can order a drive. The DVD/CD-RW Combo drive module can be inserted into your computer exactly as you would insert a CD-ROM. See “Using the CD/DVD-ROM Drive” on page 29 for directions on installing and using the RW-Combo drive. There is DVD and CD writing software included with the drive that will enable you to play DVD movies from the DVD-ROM drive.
Troubleshooting If you ever have difficulty running your computer, follow these steps: 1. Consult the following sections for advice on how to handle system problems. 2. Refer to warnings, cautions and notes within applicable portion of this manual. 3. Refer to “Windows” and other “Program” manuals as applicable. 4. If steps 1 to 3 do not resolve the problem, contact the Samsung Helpline.
Problem Action Your ATA or Compact Flashcard do not work. A patch is provided for these cards on the Recovery CD The System Setup settings are not retained when you turn off the computer. The CMOS battery inside the computer may need to be replaced. The CMOS battery provides power to save the system BIOS information when the computer is turned off. Normally, the CMOS battery lasts for several years. Do not attempt to open the chassis and replace this battery yourself or your warranty is void.
Video Problems Problem Action Nothing appears on the LCD panel when you turn on the computer. Adjust the brightness on a TFT LCD. Are you using an external monitor? If so, press to return to the LCD panel. Error Message when entering Power Management while in Multimonitor mode. If the secondary monitor is set to 256 colours, this error message could appear. Change the colour of the secondary monitor to ‘high colour (16 bit)’.
Problem If the connected CRT monitor display is not steady. Action If the refresh rate is not optimal for the connected CRT, then this problem may occur. To correct this problem do the following: 1. Click Start > Settings > Control Panel. 2. Double Click the Display icon to open the Display properties. 3. Select Settings 4. Click the Advanced button. 5. Click the Adapter tab 6. Adjust the Refresh rate to optimal or other selections until you see the CRT clearly.
Modem Problems Problem Action My modem doesn't connect to services or disconnects during communication If your modem has difficulty in connecting to on-line services and sustaining communications, first check if other devices are connected and remove them. Also remove any extension leads. Interference from certain devices or poor line power conditions may degrade the quality of your connection.
Windows & Device Drivers If for some reason your system crashes you may corrupt your HDD, Windows Operating system and/or some of your device drivers. If this is the case, use System Recovery CD to reinstall OS and System Software CD to reinstall the corrupt device drivers. Samsung may, from time to time, issue updated drivers. These are posted on the Samsung Support website at www.samsungpc.com When updating drivers, please select the “Supported” driver with the highest revision number.
Selecting a Country You have to check if the country is selected correctly before you use the modem. 1. Click Start > Settings > Control Panel. 2. Double-Click icon. 3. Select Edit in the Dialing Rules tab. 4. Select the country you are dialing from in the General tab. 5. Click OK. The new country setting is activated the next time the application is started. Or, if the application is already running, once the modem has gone offhook and then back on-hook again.
LAN Driver (Re)Installation Before you begin verify that the “Intel(R) PRO/100 VE Network Connection” is installed otherwise you will have to install it. Windows 2000 has its own PCI Ethernet Adapter driver, simply install the LAN driver according to the instructions below. 1. Start > Settings > Control Panel. 2. Double-click System icon. 3. Click the Hardware tab > Device Manager button. 4. Double-click Network Adapters in the list area. 5. Click Update Driver in the Driver tab. 6. Click Next. 7.
Sound Driver (Re)Installation When you add a new sound device Windows 2000 will recognize the addition of PCI Multimedia Audio Device and start the driver (re)installation process automatically. This also applies to reinstallation if problems occur. When Windows 2000 automatically detects a 'PCI Multimedia Audio Device', click Next and Finish. 1. Insert the System Software CD-ROM. 2. Click Start > Settings > Control Panel. 3. Double-Click System icon. 4. Choose Hardware tab > Device Manager button. 5.
Video Driver (Re)Installation If your system crashes and you have to reinstall Windows 2000 you will have to reinstall the Mobility Radeon Video Driver. To reinstall the driver complete the following steps. 1. Insert System Software CD-ROM to CD-ROM drive. 2. Click Start > Settings > Control Panel. 3. Double-Click icon. 4. Click Settings >Advanced in Display Properties. 5. Click Adapter tab > Properties button > Select Driver tab > Click Update Driver button. 6. Click Next 7. Click Next 8.
Specifications Dimension * LCD viewing area LCD viewing area (15” TFT) 304.8 x 228.6 mm Width 32.4 cm Depth 27.2 cm Height 4.1 cm Weight (with integrated floppy drive, Li-Ion battery & 14.
Abbreviations A . . . . . . . . . Amperes AC . . . . . . . . Alternating current ACPI . . . . . . Advanced Configuration and Power management Interface APM . . . . . . Advanced Power Management ATA. . . . . . . AT attachment (refers to the hard-drive interface in an ATcompatible computer) ATAPI. . . . . AT attachment packet interface BBS . . . . . . . Bulletin board system BIOS . . . . . . Basic input/output system C . . . . . . . . . Centigrade CD . . . . . . . . Compact disc CD-ROM . .
ISA . . . . . . . Industry Standard Architecture KB . . . . . . . . Kilobytes kg . . . . . . . . . Kilograms LAN. . . . . . . Local-area network lb.. . . . . . . . . Pounds LBA . . . . . . . Logical block addressing LCD. . . . . . . Liquid-crystal display m . . . . . . . . . Meters mA. . . . . . . . Milliampere mAhr . . . . . . Milliampere hour MB. . . . . . . . Megabyte mm . . . . . . . millimeter MPEG . . . . . Motion Picture Experts Group MPU . . . . . . Microprocessor unit ms . . . . . . . .
Glossary AC adapter The AC (or alternating current) adapter regulates current coming into your computer from the wall outlet. The current at the wall outlet is alternating current and needs to be changed by the adapter to DC (direct current) before your computer can use it for power.
CardBus CardBus technology enables the computer to use 32-bit PC Cards. Hardware in the computer and the Windows operating system provide support for the 32-bit cards. The voltage of 32-bit cards (3.3 volts) is lower than that of 16-bit cards (5 volts). The 32-bit cards can transmit more data at a time than the 16-bit cards, thus increasing their speed. CMOS memory CMOS (complementary metal oxide semiconductor) memory is powered by the CMOS battery.
Hard drive Also called fixed disk. A hard drive is connected to the computer and can be installed or removed. Data written to a hard drive remains until it is overwritten or corrupted. The 2.5-inch hard drive in your computer was designed for use in a notebook computer. Because hard drives in notebook computers are smaller than those in desktop computers, their maximum storage capacity may be less than that of desktop hard drives.
PC Card PC Card stands for personal computer card. The Personal Computer Memory Card International Association (PCMCIA) defines the standards used to develop all PC Cards. PC Card types include: modems, Ethernet adapters, SCSI adapters, ATA cards, and memory cards. PC slot The PC slot is the hardware slot in the computer where the PC Card is placed. Pixel A pixel is an individual dot in a graphic displayed on your computer. The pixels are so close together that they look as though they are connected.
Shadow RAM A write-protected area of RAM that contains a copy of the BIOS. As the computer boots, the BIOS is copied from its permanent location in ROM to RAM. The BIOS can be executed much faster in RAM than in ROM. The BIOS remains in shadow RAM until you turn off the computer. TFT (thin film transistor) LCD A TFT LCD uses a separate transistor circuit to control each pixel. This technology provides the best resolution for an LCD screen. A TFT LCD is also sometimes called an active matrix LCD.