SSA-R2000 RFID Reader user manual imagine the possibilities Thank you for purchasing this Samsung product. To receive more complete service, please visit our website. www.samsungsecurity.
safety information CAUTION RISK OF ELECTRIC SHOCK. DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit.
5. Keep out of direct sunlight and heat radiation sources. It may cause fire. 6. Install it in a place with good ventilation. 7. Avoid aiming the controller directly towards extremely bright objects such as sun. 8. Apparatus shall not be exposed to dripping or splashing and no objects filled with liquids, such as vases, shall be placed on the apparatus. 9. The Mains plug is used as a disconnect device and shall stay readily operable at any time.
contents PRODUCT INTRODUCTION 5 INSTALLATION AND EXTERNAL CONNECTION 8 INITIALIZATION 11 OUTPUT FORMAT 13 TROUBLESHOOTING 5 5 6 7 7 Features What’s included At a Glance Cable Color Scheme Cable Selection 8 9 10 Installation Precautions on installation External Connection 11 12 Output Format Basic Operations 13 14 WIEGAND Output 4/8 BIT BURST Output Format 15 Troubleshooting 16 Product Specifications 15 PRODUCT SPECIFICATIONS 16 4_ contents
product introduction FEATURES This product is an elegant-looking proximity reader equipped with the built-in keypad, which has the maximum of 10 cm (4”) read range. It is also supported by backlighting on the keypad, enabling stable operation at night. This product permits user access through authentication of the presented proximity card and personal identification number using the keypad. Red, green and orange LED indicators and the Piezo buzzer ensure reliable and accurate operation.
product introduction AT A GLANCE Front/Rear 6 X Y Z [ \ ] ^ _ ` lzj W lu{ 7 5 4 8 zzhTyYWWW 1 LED Displays the status of the system operation. 2 Keypad Used to enter the ID/password. 3 2-PIN Connector Can be connected to the power cable. 4 6-PIN Connector Can be connected to Wiegand cables. 5 8-PIN Connector Connected to the tamper, LED and buzzer control connection cables.
CABLE COLOR SCHEME ❖ 2-PIN Connector I/O Pins Signal Cable Color DC +12V Red Earth-grounding GND (-) Black PRODUCT INTRODUCTION Power (+12V) ❖ 6-PIN Connector I/O Pins Signal Cable Color Wiegand Data Output 0 WIK_DATA0 Green Wiegand Data Output 1 WIK_DATA1 White Not Used Not Used Orange Not Used Not Used Brown ❖ 8-PIN Connector I/O Pins Signal Cable Color Tamper Switch NC Tamper NC Green with White Stripes Tamper Switch COM Tamper COM Gray LED Control Red LED Control Whit
installation and external connection INSTALLATION 1. Attach the provided rear panel to the wall and drill two 6-32 holes and one 1/2 inch hole on it. (See [Figure 1]) 2. Refer to [Figure 2] below on how to secure the rear panel to the wall using the provided screws. 3. Apply each of 5 O-rings to the corresponding point as shown in [Figure 2]. 4. Fix the main unit with the rear panel by inserting the main unit’s cables into the center hole and pushing the main unit towards the rear panel.
PRECAUTIONS ON INSTALLATION IF INSTALLING ON A METAL WALL Metal Wall Z X Y [ \ ] _ ` ^ lzj W lu{ zzhT yYWWW Spacer Reader IF INSTALLING MORE THAN ONE READER SIDE BY SIDE OR FRONT AND BACK If you install more than one reader side by side or front and back, the read range may be reduced. In this case, if you present a card to one reader, the other reader may recognize the same card, meaning both readers read the same card simultaneously.
installation and external connection EXTERNAL CONNECTION WIRING DIAGRAM SSA-R2000 CONTROLLER Wiegand Data 0 Out Green Wiegand Data 1 Out White Tamper Switch Out(NC) Green with white stripes X Y Z Tamper Switch Out(COM) Gray [ \ ] Buzzer Control In Blue ^ _ ` LED Control In(Red) White with red stripes lzj W lu{ LED Control In(Green) Yellow LED Control In(Orange) Blue with white stripes zzhTyYWWW Red DC +12V Black GND POWER Category Cable Color Connect the DC+12V to the re
initialization OUTPUT FORMAT You can adjust the output format of the numeric values from the keypad. You can select 4/8 bit Burst or 26bit Wiegand. 1. To change the output format, use the switch on the rear of the product. ON 1 2 2. See the table below to make adjustment as needed.
initialization BASIC OPERATIONS Initial State (when the power is supplied) When you apply power to the product, it will sound beep three times before entering Standby with the red indicator turned on. Using the card Present the card to the product until you hear a beep and the green indicator turns on. The reader keeps the green indicator turned on while transferring the card data to the controller. When it is done, the green indicator turns off and for receiving the next card, the red indicator stays ON.
output format WIEGAND OUTPUT Timing Diagram 5V 1ms DATA-0 0V 5V DATA-1 LOGIC 1 2 3 n-2 n-1 0 1 1 1 0 0V n *n : 34 or26 0 Data Type (26-bit) • • • • Bit 1 : Even Parity (bit 2 ~ bit 13) Bit 2 ~ 9 : Facility Code (000 ~ 255) Bit 10 ~ 25 : ID Number (00000 ~ 65,535) Bit 26 : Odd Parity (bit 14 ~ bit 25) English13 OUTPUT FORMAT 100us
output format 4/8 BIT BURST OUTPUT FORMAT 4Bit Burst Output Format Keypads Binary Hexa Keypads Binary Hexa 0 0000 0 6 0110 6 1 0001 1 7 0111 7 2 0010 2 8 1000 8 3 0011 3 9 1001 9 4 0100 4 ESC 1010 A 5 0101 5 ENT 1011 B 8Bit Burst Output Format Keypads Binary Hexa Keypads Binary Hexa 0 11110000 F0 6 10010110 96 1 11100001 E1 7 10000111 87 2 11010010 D2 8 01111000 78 3 11000011 C3 9 01101001 69 4 10110100 B4 ESC 01011010 5A 5 10100
troubleshooting TROUBLESHOOTING If the product does not function properly, please see the below for trouble shooting. If the trouble persists, please contact the SAMSUNG Customer Service near you. SOLUTION My card is not read properly. 1) 2) Check the rated voltage specified in the user manual and the catalog. Ensure that the card must comply with the PSK (125KHz) format provided by Samsung. - Cards of 13.56MHz format can not be used. (Contact the card retailer regarding the card format.
product specifications PRODUCT SPECIFICATIONS Item SSA-R2000 Power / Current DC 12V / Max.
Correct Disposal of This Product (Waste Electrical & Electronic Equipment) (Applicable in the European Union and other European countries with separate collection systems) This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset, USB cable) should not be disposed of with other household waste at the end of their working life.
