Thank You for Choosing Samsung! Thank you for choosing Samsung! Your new Samsung product represents the latest in revision technology, We designed it with easy-to-use on-screen menus and closed captioning capabilities, making it one of the best products in its class. We are proud to offer you a product that will provide convenient, dependable service and enjoyment for years ta come.
Important Safety In formations * SS >» Read ali safety and operating instructions before operating your PDP. Keep the safety and operating instructions for future reference. Heed all warnings on the PDP and in the operating instructions. Follow all operating and use instructions. Unplug the PDP from the wall outlet before cleaning. Use a damp cloth; do not use liquid or aerosol cleaners, Never add any attachments and/or equipment without approval of the manufacturer.
Important Safety In formations (continued) Avoid overhead power lines. An outside antenna system should not be placed in the vicinity of overhead power lines or other electric light or power circuits or where it can fall into such power lines or circuits. When installing an outside antenna system, be extremely careful to keep from touching the power lines or circuits. Contact with such lines can be fatal.
FCC Information User Instructions The Federal Communications Commission Randi Frequency Interference Statement includes the following warning: NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
Important Warranty Information Regarding Television Format Viewing Wide screen format PDP Displays aspect ratio of the screen width to height) are primarily designed to view wide screen format full-motion video, The images displayed on them should primarily be in the wide screen 16:9 ratio format, or expanded to fill the screen if your model offers this feature and constantly moving.
Wiring the Mains Power Supply Plug (UK Only) ALIMENTARY NOTICE ‘The mains lead on this equipment is supplied with a molded plug incorporating a fuse. The value of the fuse is indicated on the pin face of the plug and, if it requires replacing, a fuse approved to BS11382 of the same rating must be used. Never uss the plug with the fuse cover omitted if the cover is detachable. If a replacement fuse cover is required, #f must be of the same color as the pin face of the plug.
Your New Plasma Display Panel S The actual configuration on your PDP may be different, depending on your model. PMA! Speaker Speaker = | i Power Indicator | SOURCE | i Power Off; Red ; External input selection ! i Power On; Off i Store your se in the mean ; i Timer On; Green i MENU | Menu display and exit : VOL + i : Remote Control Signal Receiver | Volume adjustment. i {Aim the remote control towards this spot on the | Adjust an option : | POP.
Your New Plasma Display Panel = The actual configuration on your PDP may be different, depending on your model. >= For further details about connection, refer to pages 48~50. 0060 60066 000 RS232C ~ IN 1 Used for the MDC function when connecting PC or R§232¢ output of another PDP. = OUT : Used for the MDC function when connecting with RS232C input of another PP. DVINA Connect to the video output jack for device with DV output. AUDIO Connect to the audio output jack on your PC or any device with DVI output.
Becoming Familiar with the Remote Control The remote control is used mainly to: ® Change sources and adjust the volume & Set up the PDP using the on-screen menu system SOUND MODE SELECTION P.MODE PICTURE MODE SELECTION DIRECT CHANNEL SELECTION PICTURE STILL VOLUME INCREASE TEMPORARY SOUND SWITCH-OFF > Press again button Yo turn the sound back on. VOLUME DECREASE.
Inserting the Batteries in the Remote Control You must insert or replace the batteries in the remote control when you: 4 Purchase the PDP 4 Find that the remote control is no longer operating correctly Remove the cover on the rear of the remote control by pressing the symbol downwards and then pulling firmly to remove it. insert two RO3, UM4, “AAA” 1.
Installing the Display on the Wall Attachment Panel oF This wall mount bracket installation guide is for the following mods ts: WMN4230/WMNS0B0/WMNE330. This installation guide may be different from the PDP User's manual. Please refer to the proper installation guide for your product. + Do not install the PDP on any place other than vertical walls. + To protect the performance of the PDP and prevent troubles, avoid the followings: ~ Do not install next to smoke and fire detectors.
Installing the Display on the Wall Attachment Panel >= The exterior of the PDP may be different than the picture {Assembly and installation of the plastic hanger is the same) 1 Remove the screws from the back of the PDP, PPM4283 1 PPMSCH3 § 2 Use the sowers and assemble the plastic hanger 0 WF + Please ask the installers to install the wall mount bracket. + Please be sure to check if the plastic hanger is completely secured on both the left and right side after hanging the PDP on the wall paramount bracket.
Connecting Speakers 1 Remove [he screws on the rear of the POP PPM4283 PPME0H3 PPME3H3 & square hales on the rear of the PDP. 3 >> When moving your PDP, do NOT hold the speaker connected to your PDP. it may damage the bracket clamping the speaker and your PDF together and result in a drop of your PDP and a risk of personal damage and injury.
Connecting Speakers (continued) Connect the speaker audio cable fo the external speaker output jack on the rear of the PDP matching the and ends of the cable with the diagram on the PDP. = # The speakers MUST have to a power handling capability of 10 WATS minimum (impedance 88). + When you connect the speaker wire to the textual speaker out connector, first bind the speaker wire round the fer rite core to secure it. [Ee The fer rite coves are used to attenuate undesired signals.
Switching On and Off The mains lead is attached to the rear of your PDP. WF" 1 you have purchased this PDP in the United Kingdom, refer to page 55 for further instructions on plug wiring, 1 Plug the mains lead into an appropriate socket. Result: The Standby indicator on the front of the PDP lights up. 3 The main voltage is indicated on the rear of the PDP and the frequency is 50 or B0Hz.
Choosing Your Language When you start using your PDP for the first time, you must select the Language which will be used for displaying menus and indications. 1 Press the MENU button Res: The main menu is displayed 2 Press the A or ¥ button to select Function. Result: The options available in the Function group are displayed EH a 3 Press the » button. Result: The Language option is selected. 4 Press the » button again. Result; The languages available are listed.
Selecting the Color System (Video or S-Video Mode) id lie AE oo >= Preset to the Video or S-Video mode by using the SOURCE bunion. If necessary, select the broadcasting standard which best corresponds to your viewing requirements. 1 Press the MENU button. Result: The options available in the picture group are displayed. 2 Press the » button, Regal: The Color System is selected.
Adjusting the Picture Settings Your PDP has several settings which allow you to control picture quality. 1 Press the MENU button. Result: The options available in the Picture group arg displayed. 2 Press the » button. 3 Press the A or ¥ button to select adjust. Press the » button. Result: The adjust menu is displayed. 4 Press the A or ¥ button to select the option (Contrast, Brightness, Sharpness, Color, Tint-SCENT only) to be adjusted. Press the « or » button. Result: The horizontal bar is displayed.
Adjusting the Picture Settings (PC or DVI Mode) = Preset to the PC mode by using the SOURCE button Press the MENU button. Result: The options available in the picture group are displayed Press the » button. Press the A or ¥ button to select Adjust. Press the » button. Result: The adjust menu is displayed. Press the A or ¥ button to select the option (Contrast, Brightness, Sharpness) to be adjusted. Press the «or button. Result: The horizontal bar is displayed.
Selecting the Picture Size You can select the picture size which best corresponds to your viewing requirements. 1 Press the MENU button. Result: The options available in the Picture group are displayed. 2 Press the » bunion. 3 Press the 4 or ¥ button to select Size. Press the » bunion, Lust can ro CEE 4 Select the option by pressing the «or » button. Result: The following modes are available depending on the input source.
Freezing the Current Picture VOL CHANNEL TE SOURCE Q You can freeze the picture when watching 2 moving picture simply by pressing the “STILL” button. To return to normal viewing, press it again. >= In the PIP mode, the main and sub pictures are stilled at the same time, Changing the Sound Mode ho You can select the type of special sound effect to be used when watching a given broadcast. 1 Press the MENU bunion. Result: The main menu is displayed. 2 Press the A or'¥ button lo select Sound.
