ACCESSORIES • MP1020 Mounting Plate • RB2030 Rechargeable Battery • TD30 Cassette Tape Deck • Pole Mounting Procedures and Precautions -20 -10 -3 0dB +6 5 0 PLAYER / R EC O R D ER REW F. F W D REC/PLAY DECK 10 RECORD LEVEL AU TO L E V E L C O N T RO L 5 AU TO S TO P O N E TO U C H 100 50 0 0 SOFT EJECT 10 PLAY LEVEL PITCH CONTROL REC PLAY REW F.
Table of Contents Introduction 1 MP1020 Mounting Plate Kit 2 RB2030 Rechargeable Battery 4 TD30 Cassette Tape Deck 6 Wireless Option 8 Pole Mounting - Procedures and Precautions 8 Specifications 9 Copyright 2000, Samson Technologies Corp. Printed October, 2000 Samson Technologies Corp. 575 Underhill Blvd. P.O. Box 9031 Syosset, NY 11791-9031 Phone: 1-800-3-SAMSON (1-800-372-6766) Fax: 516-364-3888 www.samsontech.
Introduction Welcome to Samson Expedition—the portable audio system for the new millennium! This exceptionally versatile system offers the perfect solution wherever you need portable, high-quality audio: as a main PA system or as onstage monitors in clubs and performance halls; in houses of worship; as a sound system for business presentations, mobile DJs at parties, or aerobics instruction; and for use in outdoor environments such as parks, beaches and flea markets.
MP1020 Mounting Plate WARNING! Samson assumes no responsibility or liability for either the structure or OmniMount® hardware for the mounting of Expedition cabinets. Installation should be done by qualified personnel. The Samson Expedition MP1020 Mounting Plate is designed to be used in configuration with OmniMount® models 100-STMP and 100-WB. In fixed installations where you wish to mount the Expedition to a ceiling, use the OmniMount® model 100-STMP mount.
MP1020 Mounting Plate M6 x 25 phillips machine screw M6 spring washer figure 3 figure 4 In fixed installations where you wish to mount the Expedition to a ceiling, use the OmniMount model 100-STMP mount, as shown in the illustration below: In fixed installations where you wish to mount the Expedition from a wall, use the OmniMount model 100-WB mount, as shown in the illustration below: OmniMount® Samson MP1020 mounting plate OmniMount® Samson MP1020 mounting plate OmniMount® can be reached at 1-800-
RB2030 Rechargeable Battery The Samson RB2030 Rechargeable Battery is designed for Expedition EX20 and EX30 cabinets. The RB2030 incorporates four 12VDC, 3.3A Gel Cells. A fully charged RB2030 should supply power to the EX20 or EX30 for approximately 3–4 hours at a relatively high level of volume. Battery life of 7–8 hours can be obtained if a relatively low level of volume is used.
RB2030 Rechargeable Battery 2 Using a phillips screwdriver, remove the two screws and the Battery Connector Cover Plate. Note: retain the cover plate and screws for future use. Remove the two M4 x 10 lower rear panel screws (to be re-used in step 6) and pole mount thumb screw (figure 1). 3 Align the battery as in figure 2 and set its legs in the bottom of the EX20 or EX30 as in figure 3. 4 Connect the Battery supply cable as in figure 3.
TD30 Cassette Tape Deck WARNING! Installation of the cassette deck should be done by qualified personnel. Samson assumes no responsibility, personal liability or liability for Expedition cabinets. Instructions for Installing the Cassette Tape Deck 1 Disconnect the power cord from the AC source and the Expedition cabinet. 2 With the rear of the Expedition cabinet facing you, lie the cabinet face down on a soft surface so as not to scratch the front grille.
TD30 Cassette Tape Deck 5 Feed the cassette cables under the top of the mixer through the Cassette Cable Channel (figure 3) and make the following connections. (Be careful not to force the connections as all connectors are keyed and should only fit one way.) a) Connect the 6 pin cable from cassette to the 6 pin connector located in the lower right corner of upper circuit board labeled CN501 (figure 3).
Wireless / Pole Mounting As shown in figure 1 on the left, the top panel of the Expedition EX20 and EX30 provides a prewired compartment that accommodates any of three different Samson wireless receivers: the UM1 or M32 UHF models or the VM1 VHF model. Output signal from a wireless receiver mounted in an EX30 arrives at channel 2 of the onboard mixer. Connecting a Micro Receiver to the Expedition 1 Remove the Wireless Compartment Cover by lifting it off the compartment located on the top of the Expedition.
Specifications Specifications MP1020 Mounting Plate Dimensions Weight RB2030 Rechargeable Battery Type 4 x 12VDC, 3.
Samson Technologies Corp. 575 Underhill Blvd. P.O. Box 9031 Syosset, NY 11791-9031 Phone: 1-800-3-SAMSON (1-800-372-6766) Fax: 516-364-3888 www.samsontech.
