User's Manual
Table Of Contents
- GENERAL
- 1 About these Operating Instructions
- 2 Safety Precautions
- 3 NACOS Platinum System Description
- 4 Multi Function Display
- 5 NACOS Platinum Graphical User Interface
- QUICK START GUIDE
- MAIN APPLICATIONS
- RADAR
- 1 General Information
- 1.1 RADAR Safety
- 1.2 Current IHO Standards / Regulatory Approvals
- 1.3 System Structure and Installation
- 1.4 Basics / Evaluation of the RADAR Video
- 1.4.1 Basics of the Evaluation of RADAR Video in Platinum Series
- 1.4.2 Achievable RADAR Range
- 1.4.3 Distortions of the RADAR Video
- 1.4.4 Undesirable Echo Displays and Effects
- 1.4.5 RADAR Setting for the Display of Racon Codes
- 1.4.6 RADAR Settings for Target Enhancer Detection
- 1.4.7 RADAR Setting for SART Detection (X-Band only)
- 1.4.8 Transmission formats
- 1.5 Basic setting of the RADAR Video
- 1.6 RADAR Accuracy
- 2 The RADAR Keyboard
- 3 An Overview of the Screen
- 4 RADAR Application Area
- 5 RADAR Sidebar - Permanent Area
- 6 RADAR Sidebar - Non-Permanent Area
- 7 Target Handling
- 7.1 Overview
- 7.2 Manual Target Acquisition
- 7.3 Manual Target Selection
- 7.4 Automatic Target Acquisition
- 7.5 Settings for Dangerous Targets
- 7.6 Settings for Acquisition/Guard Zones
- 7.7 Target Fusion
- 7.8 Deletion and Loss of Targets
- 7.9 Critical Target
- 7.10 Target List
- 7.11 Target Display
- 7.12 Trial Manoeuvre
- 7.13 Reference Target Tracking
- 7.14 ARPA Training
- 7.15 ARPA Malfunctions
- 7.16 AIS Malfunctions
- 8 User Symbols
- 9 CHARTRADAR (optional)
- 9.1 Overview
- 9.2 Basic Adjustments
- 9.3 Selecting the Objects to be Displayed in the Vector Chart
- 9.3.1 Overview
- 9.3.2 Categories of Display Groups
- 9.3.3 Select a Category
- 9.3.4 Select the Primary Chart Information Set (PCIS)
- 9.3.5 Indication of Category in the Status Line
- 9.3.6 Defining the Symbol Presentation
- 9.3.7 Setting the Display of Text Labels
- 9.3.8 Switch on Additional Information
- 9.3.9 Switch on Conditionally Displayed Features
- 9.4 CHARTRADAR Application Area
- 9.5 Application Area Context Menu
- 9.6 Setting the Depths Lines to be Displayed in the Vector Chart
- 9.7 Setting the Own Ship’s Draft
- 9.8 Activating the Chart Monitoring
- 9.9 Setting the Look-Ahead Sector
- 9.10 Chart Maintenance
- 9.11 Main Differences between CHARTRADAR and Full ECDISPILOT
- 1 General Information
- VOYAGE PLANNING AND MONITORING
- 1 Voyage Planning
- 1.1 Generation of Routes
- 1.1.1 General Information about Pre-planned Tracks
- 1.1.2 Generation, Handling and Administration of the Routes
- 1.1.3 Route Display Settings
- 1.1.4 Route Editing - Graphical
- 1.1.5 Route Editing - Text Mode
- 1.1.6 Details of the Waypoint Data
- 1.1.7 Checking of Routes
- 1.1.8 Completing the Generation of the Route
- 1.1.9 Import / Export Routes
- 1.1 Generation of Routes
- 2 Chart and Route Monitoring
- 1 Voyage Planning
- CONNING
- SENSORS
- OPTIONAL APPLICATIONS
- MAINTENANCE
- 1 Performance Monitor
- 2 Data Maintenance of the Electronic Charts
- 2.1 General
- 2.2 Starting Chart Maintenance
- 2.3 Chart Maintenance Application Area
- 2.4 Update of Charts from Media
- 2.5 Messages during Chart Update
- 2.6 Display Charts which are on a Media or a MFD (workstation)
- 2.7 Maintenance of Charts on your MFD (workstation)
- 2.8 Display Expander
- 2.9 Backup/Restore of Map Data
- 3 Manual ENC Update Editor
- 4 Hardware Maintenance
- 5 SW Version and Updates
- ALARMS
- LISTS AND INDEXES
- DOCUMENT HISTORY
NACOS Platinum
ED 3100 G 140 / 04 (2011-11)
Operating Instructions
V-2 Alarm Management
V Alarms.fm / 10.11.11
V-20
AIS TGT Capacity Limit
100% of the maximum number of acquired AIS targets are being tracked.
Remedy: Delete at least one unimportant AIS target.
AIS New Safety Message
The AIS has received a safety message.
The safety message can be read under > Tools > Target > Message.
AIS No Valid COG
The AIS system has no valid course over ground information.
Remedy: Check the connected sensor and cabling. (Typically the COG information from an inte-
grated bridge system which is derived from a GPS sensor, the AIS will continue to work but will
transmit less information to other ships.)
AIS No Valid Heading
The AIS system has no valid heading information from the sensor.
Remedy: Check the heading sensor. (Typically the heading information from an integrated bridge
system which is derived from the gyro, the AIS will continue to work but will transmit less informa-
tion to other ships.)
AIS No Valid Position
The AIS system has no valid position information from internal position sensor
Remedy: Check the cabling and the antenna of the internal GPS sensor. (Typically the position
information from an integrated bridge system which is derived from a GPS sensor, the AIS will
continue to work with its own sensor, but the position, which is sent out to other ships might not
be as accurate as before)
AIS No Valid ROT
The AIS has no valid rate of turn information from the sensor.
Remedy: Check the sensor and the cabling. (Typically the rate of turn information from an inte-
grated bridge system which is derived from the gyro, the AIS will continue to work but will transmit
less information to other ships)
AIS No Valid SOG
The AIS has no valid speed over ground information.
Remedy: Check selected speed sensor. (Typically the SOG information from an integrated bridge
system which is derived from a GPS sensor, the AIS will continue to work with its own sensor, but
the speed, which is sent out to other ships might not be as accurate as before)
AIS Offline
Remedy: Check the AIS system. It might be possible to eliminate the fault by switching the voltage
supply to the AIS electronics unit off and then on again at the ship's mains.