User's Manual
Table Of Contents
- List of Contents
- List of Figures
- List of Abbreviations
- 1 General
- 2 Overview
- 2.1 Compatibility with Other Systems
- 2.2 AIS 3410 in RADARPILOT 1000/1100 Systems
- 2.3 AIS 3410 in 1000/1100 Series Systems (NACOS xx-4 and xx-5)
- 2.4 AIS 3410 in CHARTPILOT Stand-alone Systems
- 2.5 AIS 3410 in NACOS xx-3 Systems (Radar 9xxx and CHARTPILOT)
- 2.6 AIS 3410 in Radar 9xxx Systems with RADARPILOT 1000/1100
- 2.7 AIS 3410 in Radar 9xxx Systems
- 2.8 Housing of the 3410 Electronics Unit
- 2.9 Replacement of AIS Electronics Unit
- 2.10 Media Converter Installation (necessary for ships with BNC LAN networks)
- 3 Installation Recommendations
- 3.1 General Recommendations
- 3.2 Specific Recommendations
- 3.2.1 Recommendations Concerning AIS Systems
- 3.2.2 Recommendations Concerning the Installation of the Electronics Unit
- 3.2.3 Recommendations Concerning the Installation of the Antennas
- 3.2.4 Recommendations Concerning Redundancy
- 3.2.5 Recommendations Concerning the Connection of a (D)GPS to AIS 3410
- 3.2.6 Emergency Power Source
- 3.2.7 Pilot Port, Connector/Cable Kits
- 3.2.8 Recommendations Concerning AIS Stand-alone with Radar 9xxx / NACOS xx-2/-3
- 3.2.9 Recommendations Concerning the Connection to a Radar 1000/1100 Series System
- 3.2.10 Recommendations Concerning the Connection to a Radar 1100 Series System
- 4 Functional Description
- 4.1 Block Diagram
- 4.2 Termination
- 4.3 Description of the Components
- 4.3.1 AIS 3410 Electronics Unit
- 4.3.1.1 Interfaces
- 4.3.1.2 Internal Connectors
- 4.3.1.3 Supported Sensor Input Sentences
- 4.3.1.4 Supported Sentences for the AIS Primary Display Port and the Pilot Port
- 4.3.1.5 Supported Sentences for the Long Range Port
- 4.3.1.6 Supported Sentences for the Internal Position Sensor
- 4.3.1.7 IEC 61162 -1/-2 Interfaces, Electrical Characteristics
- 4.3.1.8 Example for the Interconnection
- 4.3.2 VHF Antenna
- 4.3.3 GPS Antenna
- 4.3.4 Pilot Port
- 4.3.1 AIS 3410 Electronics Unit
- 5 Setting-to-Work/Configuration
- 6 Repair/Maintenance
- 7 Technical Data
- 8 Fault Code List
- 9 Cabling Documents
- 10 Outline Drawings
- Notes
AIS 3410, Electronics Unit
ED3047G842 / 01 (2009-08)
Technical Manual
1 General
1.1 Software Releases
t_ue_e01.fm / 27.08.09
9
1 General
This Technical Manual is the technical reference manual for the following components:
- AIS 3410 Electronics Unit
The manual contains further information about the antennas (GPS, VHF).
1.1 Software Releases
This manual is valid for all software versions of the AIS 3410. See also Section 5.2.
1.2 General Recommendations for Installation, Maintenance and Repair Work
SAM Electronics gives advice and recommendations for the arrangement of SAM Electronics equipment
and the installation sites. A prerequisite is that the necessary drawings of the ship should be made avail
-
able in good time.
This advice and these recommendations are given on the basis of our up-to-date practical experience
and to the best of our knowledge. However, they are given without any commitment. As far as is permis
-
sible, any liability on the part of SAM Electronics for resulting damage is expressly ruled out, regardless
of whether the damage is of a direct or indirect nature.
Unusual shipbuilding shapes, additions or superstructures as well as environmental influences can impair
the functioning of the equipment. We are, of course, willing to help the customer with optimizing solutions
subject to suitable commercial arrangements.
The customer is responsible for ensuring that SAM Electronics equipment is installed properly according
to our instructions and in compliance with the regulations issued by the relevant classification society and
national authorities.
1.3 Safety Warnings
WARNING
This unit contains electrostatic sensitive devices.
Observe precautions for handling.
The discharge of electrostatic energy into a semiconductor can destroy the
semiconductor or change its properties. Before a unit’s housing is opened to remove or touch a board,
the service equipment, Order No. 586-5011, must be used.
1. The mat must be positioned at the workplace.
2. The potential equalization cable must be connected to the snap fastener and the clamp to a suitable
protective earth contact. The cable contains a 1
MΩ resistor which must not be removed.
3. The wrist band must be put on. When the spiral cable is connected to the snap fastener, the
discharge line is established.
4. Thoroughly grounded soldering, measurement and test tools must be used. If these tools are
supplied with power from the 230
VAC mains, this supply must be protected by a fault current plug,
stock No. 593-8099.