User's Manual
Table Of Contents
- List of Contents
- List of Figures
- List of Abbreviations
- 1 General
- 2 Overview
- 2.1 Compatibility with Other Systems
- 2.2 AIS 3410 in RADARPILOT 1000/1100 Systems
- 2.3 AIS 3410 in 1000/1100 Series Systems (NACOS xx-4 and xx-5)
- 2.4 AIS 3410 in CHARTPILOT Stand-alone Systems
- 2.5 AIS 3410 in NACOS xx-3 Systems (Radar 9xxx and CHARTPILOT)
- 2.6 AIS 3410 in Radar 9xxx Systems with RADARPILOT 1000/1100
- 2.7 AIS 3410 in Radar 9xxx Systems
- 2.8 Housing of the 3410 Electronics Unit
- 2.9 Replacement of AIS Electronics Unit
- 2.10 Media Converter Installation (necessary for ships with BNC LAN networks)
- 3 Installation Recommendations
- 3.1 General Recommendations
- 3.2 Specific Recommendations
- 3.2.1 Recommendations Concerning AIS Systems
- 3.2.2 Recommendations Concerning the Installation of the Electronics Unit
- 3.2.3 Recommendations Concerning the Installation of the Antennas
- 3.2.4 Recommendations Concerning Redundancy
- 3.2.5 Recommendations Concerning the Connection of a (D)GPS to AIS 3410
- 3.2.6 Emergency Power Source
- 3.2.7 Pilot Port, Connector/Cable Kits
- 3.2.8 Recommendations Concerning AIS Stand-alone with Radar 9xxx / NACOS xx-2/-3
- 3.2.9 Recommendations Concerning the Connection to a Radar 1000/1100 Series System
- 3.2.10 Recommendations Concerning the Connection to a Radar 1100 Series System
- 4 Functional Description
- 4.1 Block Diagram
- 4.2 Termination
- 4.3 Description of the Components
- 4.3.1 AIS 3410 Electronics Unit
- 4.3.1.1 Interfaces
- 4.3.1.2 Internal Connectors
- 4.3.1.3 Supported Sensor Input Sentences
- 4.3.1.4 Supported Sentences for the AIS Primary Display Port and the Pilot Port
- 4.3.1.5 Supported Sentences for the Long Range Port
- 4.3.1.6 Supported Sentences for the Internal Position Sensor
- 4.3.1.7 IEC 61162 -1/-2 Interfaces, Electrical Characteristics
- 4.3.1.8 Example for the Interconnection
- 4.3.2 VHF Antenna
- 4.3.3 GPS Antenna
- 4.3.4 Pilot Port
- 4.3.1 AIS 3410 Electronics Unit
- 5 Setting-to-Work/Configuration
- 6 Repair/Maintenance
- 7 Technical Data
- 8 Fault Code List
- 9 Cabling Documents
- 10 Outline Drawings
- Notes
AIS 3410, Electronics Unit
ED3047G842 / 01 (2009-08)
Technical Manual
9 Cabling Documents
t_ue_e11.fm / 27.08.09
67
9 Cabling Documents
Grounding
All components of the system have contacts such as bolts or terminals for grounding. Grounding is impor-
tant for EMC purposes as well as for protecting people’s lives. Both purposes are covered by the
standard grounding of the system’s housings to the ship’s metallic structure (bolted or welded). Regard
-
less of the type of ship’s grounding (e.g. star pattern or ground plane pattern), no potential difference
should be measurable between two different ground connectors. Potential differences cause compensa
-
tion currents on the cable shields. If the ship has no metallic structure, all conductively connected metallic
parts form an artificial ground.
All ground connections should be as short as possible. If possible, different units should be connected to
individual ground connectors. Whenever possible, metallic housings should be screwed or welded directly
to the ship’s metallic structure. If a safe grounding contact is not ensured, additional conductors are
necessary. Furthermore, all ground connections should have a low RF-impedance, and should be
resistant against vibration and corrosion. Grounding conductors on an open-air deck must be made of
corrosion-protected steel, and inside the ship they must be made of copper.
The grounding should be done in such a way that the connection can be inspected in a convenient
manner.
EMC Purposes
The shields of all cables must be connected at both ends if no other instructions are given.
Protective Ground
All removable metallic parts of the housings are grounded by means of separate, flexible cables to the
main structure of the housing. It is important to connect this ground-cable after parts have been
dismounted or exchanged.
Title Page
Cable Diagram, connection to RADARPILOT 1x00, NACOS xx-4/5 via Primary Display Port
68
Cable Diagram, connection to CHARTPILOT, NACOS xx-4/5, RADAR / MULTIPILOT 1x00 via LAN
69
Cable Diagram, connection to CHARTPILOT stand-alone
70
Cable Diagram, connection to Radar 9xxx via Radar 9xxx AIS Interface (NACOS xx-3)
71
Detailed Cable Diagram, connection to RADARPILOT 1x00, NACOS xx-4/5 via Primary Display Port
72
Detailed Cable Diagram, Wheelhouse Console
73
Detailed Cable Diagram, connection to NACOS xx-4/5, RADAR / MULTIPILOT 1x00 via LAN
74
Detailed Cable Diagram, connection to CHARTPILOT stand-alone systems
75
Detailed Cable Diagram, connection to RADAR 9xxx AIS Interface
76
Detailed Cable Diagram, connection to RADAR 9xxx AIS Interface PCB GE 3044 G 220
77