User's Manual
Table Of Contents
- List of Contents
- List of Figures
- List of Abbreviations
- 1 General
- 2 Overview
- 2.1 Compatibility with Other Systems
- 2.2 AIS 3410 in RADARPILOT 1000/1100 Systems
- 2.3 AIS 3410 in 1000/1100 Series Systems (NACOS xx-4 and xx-5)
- 2.4 AIS 3410 in CHARTPILOT Stand-alone Systems
- 2.5 AIS 3410 in NACOS xx-3 Systems (Radar 9xxx and CHARTPILOT)
- 2.6 AIS 3410 in Radar 9xxx Systems with RADARPILOT 1000/1100
- 2.7 AIS 3410 in Radar 9xxx Systems
- 2.8 Housing of the 3410 Electronics Unit
- 2.9 Replacement of AIS Electronics Unit
- 2.10 Media Converter Installation (necessary for ships with BNC LAN networks)
- 3 Installation Recommendations
- 3.1 General Recommendations
- 3.2 Specific Recommendations
- 3.2.1 Recommendations Concerning AIS Systems
- 3.2.2 Recommendations Concerning the Installation of the Electronics Unit
- 3.2.3 Recommendations Concerning the Installation of the Antennas
- 3.2.4 Recommendations Concerning Redundancy
- 3.2.5 Recommendations Concerning the Connection of a (D)GPS to AIS 3410
- 3.2.6 Emergency Power Source
- 3.2.7 Pilot Port, Connector/Cable Kits
- 3.2.8 Recommendations Concerning AIS Stand-alone with Radar 9xxx / NACOS xx-2/-3
- 3.2.9 Recommendations Concerning the Connection to a Radar 1000/1100 Series System
- 3.2.10 Recommendations Concerning the Connection to a Radar 1100 Series System
- 4 Functional Description
- 4.1 Block Diagram
- 4.2 Termination
- 4.3 Description of the Components
- 4.3.1 AIS 3410 Electronics Unit
- 4.3.1.1 Interfaces
- 4.3.1.2 Internal Connectors
- 4.3.1.3 Supported Sensor Input Sentences
- 4.3.1.4 Supported Sentences for the AIS Primary Display Port and the Pilot Port
- 4.3.1.5 Supported Sentences for the Long Range Port
- 4.3.1.6 Supported Sentences for the Internal Position Sensor
- 4.3.1.7 IEC 61162 -1/-2 Interfaces, Electrical Characteristics
- 4.3.1.8 Example for the Interconnection
- 4.3.2 VHF Antenna
- 4.3.3 GPS Antenna
- 4.3.4 Pilot Port
- 4.3.1 AIS 3410 Electronics Unit
- 5 Setting-to-Work/Configuration
- 6 Repair/Maintenance
- 7 Technical Data
- 8 Fault Code List
- 9 Cabling Documents
- 10 Outline Drawings
- Notes
AIS 3410, Electronics Unit
ED3047G842 / 01 (2009-08)
Technical Manual
8 Fault Code List
t_ue_e09.fm / 27.08.09
63
8 Fault Code List
The following fault codes (integrity alarm conditions) can be displayed at the connected display unit (for
example a RADARPILOT 1000/1100). See also
Section 6 from page 47 on for further information.
Fault
Messages at
Error Message generated by,
Possible Cause/Source,
Reaction of the System,
Remedy
1000/1100 Series,
CHARTPILOT,
MULTIPLOT 910x
(Chart Mode)
Radar 9xxx, MULTIP-
ILOT 910x (Radar
Mode)
001 AIS: Tx malfunction AIS TX MALFUNCTION
Generated by: AIS Electronics Unit
Cause/Source: VHF Antenna, cabling
Reaction: The Electronics Unit stops the transmission.
Remedy: Check of the antenna and the antenna cabling
(short circuit or missing contact at the connectors)
002
AIS: Antenna
VSWR exceeds limit
(VSWR = Voltage
Standing Wave
Ratio)
AIS VSWR LIMIT
Generated by: AIS Electronics Unit
Cause/Source: VHF antenna, installation
Reaction: The Electronics Unit continues operation.
Remedy: Check of the antenna and the antenna cabling
(75
Ω cable instead of 50 Ω cable)
003
AIS: Rx channel 1
malfunction
AIS RX CH1 FAULT
Generated by: AIS Electronics Unit
Cause/Source: Internal error
Reaction: The Electronics Unit stops the transmission on the
affected channel.
Remedy: The Electronics Unit must be exchanged.
004
AIS: Rx channel 2
malfunction
AIS RX CH2 FAULT
005
AIS: Rx channel 70
malfunction
AIS RX CH70 FAULT
006 AIS: General failure AIS GENERAL FAULT
Generated by: AIS Electronics Unit
Cause/Source: Internal error
Reaction: The Electronics Unit stops the transmission.
Remedy: The Electronics Unit must be exchanged.
008
AIS: MKD connec-
tion lost (MKD =
Minimum Keyboard
Display)
AIS CONNECTION
Generated by: AIS Electronics Unit
Cause/Source: No Operating/Display Unit connected
Reaction: The Electronics Unit continues operation.
Remedy: The Display Unit (for example a RADARPILOT
1x00) does not communicate with the Electronics Unit. Check
the cabling/connection of the Primary Display Port. Check if
the Display Unit is working.
025
AIS: External EPFS
lost
(EPFS = Electronic
Position Fixing
System such as
GPS)
AIS EXTERNAL EPFS
Generated by: AIS Electronics Unit
Cause/Source: No valid position data at interface S1, S2, S3
Reaction: The Electronics Unit continues operation with the
position data of the internal position sensor. If there is no
valid position data available from the internal position sensor,
additionally error 026 is displayed.
Remedy: The telegrams GLL, GNS, GGA, RMC can not be
received. Check the sensor and the cabling; Check if the
system that delivers the data is working (RADARPILOT
1x00); Check the baud rate settings of the sensor inputs.
026
AIS: No sensor
position in use
AIS NO POSITION
Generated by: AIS Electronics Unit
Cause/Source: No valid position from internal position sensor
Reaction: The Electronics Unit continues operation.
Remedy: Check the cabling and the antenna of the internal
GPS sensor.