User's Manual
Table Of Contents
- List of Contents
- List of Figures
- List of Abbreviations
- 1 General
- 2 Overview
- 2.1 Compatibility with Other Systems
- 2.2 AIS 3410 in RADARPILOT 1000/1100 Systems
- 2.3 AIS 3410 in 1000/1100 Series Systems (NACOS xx-4 and xx-5)
- 2.4 AIS 3410 in CHARTPILOT Stand-alone Systems
- 2.5 AIS 3410 in NACOS xx-3 Systems (Radar 9xxx and CHARTPILOT)
- 2.6 AIS 3410 in Radar 9xxx Systems with RADARPILOT 1000/1100
- 2.7 AIS 3410 in Radar 9xxx Systems
- 2.8 Housing of the 3410 Electronics Unit
- 2.9 Replacement of AIS Electronics Unit
- 2.10 Media Converter Installation (necessary for ships with BNC LAN networks)
- 3 Installation Recommendations
- 3.1 General Recommendations
- 3.2 Specific Recommendations
- 3.2.1 Recommendations Concerning AIS Systems
- 3.2.2 Recommendations Concerning the Installation of the Electronics Unit
- 3.2.3 Recommendations Concerning the Installation of the Antennas
- 3.2.4 Recommendations Concerning Redundancy
- 3.2.5 Recommendations Concerning the Connection of a (D)GPS to AIS 3410
- 3.2.6 Emergency Power Source
- 3.2.7 Pilot Port, Connector/Cable Kits
- 3.2.8 Recommendations Concerning AIS Stand-alone with Radar 9xxx / NACOS xx-2/-3
- 3.2.9 Recommendations Concerning the Connection to a Radar 1000/1100 Series System
- 3.2.10 Recommendations Concerning the Connection to a Radar 1100 Series System
- 4 Functional Description
- 4.1 Block Diagram
- 4.2 Termination
- 4.3 Description of the Components
- 4.3.1 AIS 3410 Electronics Unit
- 4.3.1.1 Interfaces
- 4.3.1.2 Internal Connectors
- 4.3.1.3 Supported Sensor Input Sentences
- 4.3.1.4 Supported Sentences for the AIS Primary Display Port and the Pilot Port
- 4.3.1.5 Supported Sentences for the Long Range Port
- 4.3.1.6 Supported Sentences for the Internal Position Sensor
- 4.3.1.7 IEC 61162 -1/-2 Interfaces, Electrical Characteristics
- 4.3.1.8 Example for the Interconnection
- 4.3.2 VHF Antenna
- 4.3.3 GPS Antenna
- 4.3.4 Pilot Port
- 4.3.1 AIS 3410 Electronics Unit
- 5 Setting-to-Work/Configuration
- 6 Repair/Maintenance
- 7 Technical Data
- 8 Fault Code List
- 9 Cabling Documents
- 10 Outline Drawings
- Notes
AIS 3410, Electronics Unit
ED3047G842 / 01 (2009-08)
Technical Manual
6 Repair/Maintenance
6.3 Software Update
t_ue_e07.fm / 27.08.09
57
7. A status windows appears during the update.
8. It must be waited until the message "Flash programming finished, system is rebooting" appears.
9. The Electronics Unit reboots automatically. The OK button closes the window of the update routine.
10. Verify the proper function of the system, make sure that AIS targets and sensor data will be
displayed on the connected display system.
11. Verify that the Update was successful and the new software version is installed.
WARNING!
Do not interrupt the update! If update procedure is interrupted, the Elec-
tronics Unit may come into an undefined status, in which no further
update or operation is possible. See
Section 6.3 on page 54 in this case.
During the update the new software is stored in the RAM module of the AIS. After the successful transfer
the old version will be deleted by erasing the Flash ROM. Then the update file will be stored on the Flash
ROM.
If the power supply was interrupted during the update process, it may occur in seldom cases, that the
electronics unit is not restarting again. In this case it may necessary to exchange the Disk On Chip
memory module.
6.3.5 Software Update by means of a CHARTPILOT or MULTIPILOT 91x0
If a CHARTPILOT or MULTIPILOT 91x0 is connected (the AIS Electronics Unit must be connected to the
LAN), it is possible to update the AIS by means of one of these systems. The update of the AIS Elec
-
tronics Unit is possible from CHARTPILOT/MULTIPILOT software version 5.1 onwards.
WARNING!
Do not change any CHARTPILOT settings while doing the software
update via CHARTPILOT or MULTIPILOT. This may cause problems of
the ECDIS application and can degrade the performance of your naviga
-
tion system.
1. Put the Update CD ROM in the CD ROM drive of the CHARTPILOT.
2. Open the System Maintenance menu (Tree => System Maintenance).
3. Open the Configuration menu and input the service password.
4. Open the AIS menu and start the software update program.
z_ue_053.jpg