User's Manual
Table Of Contents
- List of Contents
- List of Figures
- List of Abbreviations
- 1 General
- 2 Overview
- 2.1 Compatibility with Other Systems
- 2.2 AIS 3410 in RADARPILOT 1000/1100 Systems
- 2.3 AIS 3410 in 1000/1100 Series Systems (NACOS xx-4 and xx-5)
- 2.4 AIS 3410 in CHARTPILOT Stand-alone Systems
- 2.5 AIS 3410 in NACOS xx-3 Systems (Radar 9xxx and CHARTPILOT)
- 2.6 AIS 3410 in Radar 9xxx Systems with RADARPILOT 1000/1100
- 2.7 AIS 3410 in Radar 9xxx Systems
- 2.8 Housing of the 3410 Electronics Unit
- 2.9 Replacement of AIS Electronics Unit
- 2.10 Media Converter Installation (necessary for ships with BNC LAN networks)
- 3 Installation Recommendations
- 3.1 General Recommendations
- 3.2 Specific Recommendations
- 3.2.1 Recommendations Concerning AIS Systems
- 3.2.2 Recommendations Concerning the Installation of the Electronics Unit
- 3.2.3 Recommendations Concerning the Installation of the Antennas
- 3.2.4 Recommendations Concerning Redundancy
- 3.2.5 Recommendations Concerning the Connection of a (D)GPS to AIS 3410
- 3.2.6 Emergency Power Source
- 3.2.7 Pilot Port, Connector/Cable Kits
- 3.2.8 Recommendations Concerning AIS Stand-alone with Radar 9xxx / NACOS xx-2/-3
- 3.2.9 Recommendations Concerning the Connection to a Radar 1000/1100 Series System
- 3.2.10 Recommendations Concerning the Connection to a Radar 1100 Series System
- 4 Functional Description
- 4.1 Block Diagram
- 4.2 Termination
- 4.3 Description of the Components
- 4.3.1 AIS 3410 Electronics Unit
- 4.3.1.1 Interfaces
- 4.3.1.2 Internal Connectors
- 4.3.1.3 Supported Sensor Input Sentences
- 4.3.1.4 Supported Sentences for the AIS Primary Display Port and the Pilot Port
- 4.3.1.5 Supported Sentences for the Long Range Port
- 4.3.1.6 Supported Sentences for the Internal Position Sensor
- 4.3.1.7 IEC 61162 -1/-2 Interfaces, Electrical Characteristics
- 4.3.1.8 Example for the Interconnection
- 4.3.2 VHF Antenna
- 4.3.3 GPS Antenna
- 4.3.4 Pilot Port
- 4.3.1 AIS 3410 Electronics Unit
- 5 Setting-to-Work/Configuration
- 6 Repair/Maintenance
- 7 Technical Data
- 8 Fault Code List
- 9 Cabling Documents
- 10 Outline Drawings
- Notes
AIS 3410, Electronics Unit
ED3047G842 / 01 (2009-08)
Technical Manual
6 Repair/Maintenance
6.3 Software Update
t_ue_e07.fm / 27.08.09
56
Connection at the Electronics Unit
The cable must be connected to the serial service interface of the computer and to the connector on the
top of the Electronics Unit’s port
Fig. 6-6 Service Interface
6.3.4 Software Update by means of a Laptop
1. Disconnect the Electronics Unit from the power supply for about 5 s.
2. Connect the power supply and wait about 2 minutes until the Electronics Unit has been restarted.
3. Connect the update cable before the update software is started.
4. Download the update from the SAM-CMIS system (see Section 6.3.1), unzip the file and save the
unzipped directory structure to the hard disk or on a CD ROM.
5. To start the update software open the directory of the software version which shall be installed
(usually the newest version; for details see the readme file)
DOS command line:
CD X:\AIS\ElectronicsUnit3410\BuildNNN_YYYYMMDD\root
(DRIVE X name of the drive, NNN = release of the software, YYYY=year, MM=month, DD=day)
Type aisupdate.exe to start the software.
Type aisupdate.exe on the command line to start the program.
Windows Explorer:
Open the Windows Explorer and select the drive with the update directory.
Select the following path by clicking twice on the directory names: AIS -> ElectronicsUnit3410
-> BuildNNN_YYYY_MM_DD -> root
Start the program aisupdate.exe by clicking twice on the corresponding icon.
6. Click the Start Update button.
If a failure message appears, press the COM 1 button to switch the serial port used by the program
to COM 2.
Service Interface
z_ue_052.jpg