User's Manual
Table Of Contents
- List of Contents
- List of Figures
- List of Abbreviations
- 1 General
- 2 Overview
- 2.1 Compatibility with Other Systems
- 2.2 AIS 3410 in RADARPILOT 1000/1100 Systems
- 2.3 AIS 3410 in 1000/1100 Series Systems (NACOS xx-4 and xx-5)
- 2.4 AIS 3410 in CHARTPILOT Stand-alone Systems
- 2.5 AIS 3410 in NACOS xx-3 Systems (Radar 9xxx and CHARTPILOT)
- 2.6 AIS 3410 in Radar 9xxx Systems with RADARPILOT 1000/1100
- 2.7 AIS 3410 in Radar 9xxx Systems
- 2.8 Housing of the 3410 Electronics Unit
- 2.9 Replacement of AIS Electronics Unit
- 2.10 Media Converter Installation (necessary for ships with BNC LAN networks)
- 3 Installation Recommendations
- 3.1 General Recommendations
- 3.2 Specific Recommendations
- 3.2.1 Recommendations Concerning AIS Systems
- 3.2.2 Recommendations Concerning the Installation of the Electronics Unit
- 3.2.3 Recommendations Concerning the Installation of the Antennas
- 3.2.4 Recommendations Concerning Redundancy
- 3.2.5 Recommendations Concerning the Connection of a (D)GPS to AIS 3410
- 3.2.6 Emergency Power Source
- 3.2.7 Pilot Port, Connector/Cable Kits
- 3.2.8 Recommendations Concerning AIS Stand-alone with Radar 9xxx / NACOS xx-2/-3
- 3.2.9 Recommendations Concerning the Connection to a Radar 1000/1100 Series System
- 3.2.10 Recommendations Concerning the Connection to a Radar 1100 Series System
- 4 Functional Description
- 4.1 Block Diagram
- 4.2 Termination
- 4.3 Description of the Components
- 4.3.1 AIS 3410 Electronics Unit
- 4.3.1.1 Interfaces
- 4.3.1.2 Internal Connectors
- 4.3.1.3 Supported Sensor Input Sentences
- 4.3.1.4 Supported Sentences for the AIS Primary Display Port and the Pilot Port
- 4.3.1.5 Supported Sentences for the Long Range Port
- 4.3.1.6 Supported Sentences for the Internal Position Sensor
- 4.3.1.7 IEC 61162 -1/-2 Interfaces, Electrical Characteristics
- 4.3.1.8 Example for the Interconnection
- 4.3.2 VHF Antenna
- 4.3.3 GPS Antenna
- 4.3.4 Pilot Port
- 4.3.1 AIS 3410 Electronics Unit
- 5 Setting-to-Work/Configuration
- 6 Repair/Maintenance
- 7 Technical Data
- 8 Fault Code List
- 9 Cabling Documents
- 10 Outline Drawings
- Notes
AIS 3410, Electronics Unit
ED3047G842 / 01 (2009-08)
Technical Manual
6 Repair/Maintenance
6.1 Trouble Shooting
t_ue_e07.fm / 27.08.09
49
6.1.3 Trouble Shooting for AIS 3410 connected to a RADARPILOT 1000/1100
6.1.3.1
Indication: System Fault Message 3617 Displayed on Indicator
NOTE:
The following instructions are valid only, if the AIS is connected via the Primary Display Port. The
AIS 3410 Electronics Unit can also be connected via the Ethernet LAN (RADARPILOT/CHARTRADAR
1000/1100: with software 3.0 or newer or MULTIPILOT 1000/1100).
Procedure:
1. Check the cabling of the Sensor Input Channels and the Primary Display port. See the Technote
T0211-340x-002 or
Section 3.1.1 for further information.
2. Check the correct setting of the S1 and the jumpers of the Interface Assembly SH3014G203. S1
must be set to position 2. No jumpers should be connected to the pins 1...4. See the Technical
Manual of the RADARPILOT 1000/1100 for further information.
If the system fault message is still existing, the communication on the Primary Display Port must be
checked. Proceed as follows:
Test of the RADARPILOT/CHARTRADAR/MULTIPILOT Output
1. Power Down the system
No AIS targets visible but
no alarm messages are
given
VHF antenna broken Replace VHF antenna
Replace Elec-
tronics Module
VHF antenna cable broken Replace VHF antenna cable
Contact service
department
VHF antenna connector
broken
Replace VHF antenna
connector
271178666
VHF module defective Replace Electronics Module 271259341
Hot Housing
Housing fan
(only old housing)
Replace external fan
(only old housing)
300006159
Wrong installation Check installation -
No heading data
Gyro Interface DEBEG 4901
defective
Replace DEBEG 4901 300005797
Connection to gyro system
broken
Check gyro system and
connection to AIS
-
Wrong configuration Check configuration -
Connection to radar system
broken
Check connection AIS/radar
No external GNSS data
Connection to GPS broken
Check GPS and connection
to AIS
-
Wrong configuration Check configuration -
Connection to radar system
broken
Check connection AIS/radar
Failure Description Possible Causes Service Measure Spare Part No.