User's Manual
Table Of Contents
- List of Contents
- List of Figures
- List of Abbreviations
- 1 General
- 2 Overview
- 2.1 Compatibility with Other Systems
- 2.2 AIS 3410 in RADARPILOT 1000/1100 Systems
- 2.3 AIS 3410 in 1000/1100 Series Systems (NACOS xx-4 and xx-5)
- 2.4 AIS 3410 in CHARTPILOT Stand-alone Systems
- 2.5 AIS 3410 in NACOS xx-3 Systems (Radar 9xxx and CHARTPILOT)
- 2.6 AIS 3410 in Radar 9xxx Systems with RADARPILOT 1000/1100
- 2.7 AIS 3410 in Radar 9xxx Systems
- 2.8 Housing of the 3410 Electronics Unit
- 2.9 Replacement of AIS Electronics Unit
- 2.10 Media Converter Installation (necessary for ships with BNC LAN networks)
- 3 Installation Recommendations
- 3.1 General Recommendations
- 3.2 Specific Recommendations
- 3.2.1 Recommendations Concerning AIS Systems
- 3.2.2 Recommendations Concerning the Installation of the Electronics Unit
- 3.2.3 Recommendations Concerning the Installation of the Antennas
- 3.2.4 Recommendations Concerning Redundancy
- 3.2.5 Recommendations Concerning the Connection of a (D)GPS to AIS 3410
- 3.2.6 Emergency Power Source
- 3.2.7 Pilot Port, Connector/Cable Kits
- 3.2.8 Recommendations Concerning AIS Stand-alone with Radar 9xxx / NACOS xx-2/-3
- 3.2.9 Recommendations Concerning the Connection to a Radar 1000/1100 Series System
- 3.2.10 Recommendations Concerning the Connection to a Radar 1100 Series System
- 4 Functional Description
- 4.1 Block Diagram
- 4.2 Termination
- 4.3 Description of the Components
- 4.3.1 AIS 3410 Electronics Unit
- 4.3.1.1 Interfaces
- 4.3.1.2 Internal Connectors
- 4.3.1.3 Supported Sensor Input Sentences
- 4.3.1.4 Supported Sentences for the AIS Primary Display Port and the Pilot Port
- 4.3.1.5 Supported Sentences for the Long Range Port
- 4.3.1.6 Supported Sentences for the Internal Position Sensor
- 4.3.1.7 IEC 61162 -1/-2 Interfaces, Electrical Characteristics
- 4.3.1.8 Example for the Interconnection
- 4.3.2 VHF Antenna
- 4.3.3 GPS Antenna
- 4.3.4 Pilot Port
- 4.3.1 AIS 3410 Electronics Unit
- 5 Setting-to-Work/Configuration
- 6 Repair/Maintenance
- 7 Technical Data
- 8 Fault Code List
- 9 Cabling Documents
- 10 Outline Drawings
- Notes
AIS 3410, Electronics Unit
ED3047G842 / 01 (2009-08)
Technical Manual
3 Installation Recommendations
3.1 General Recommendations
t_ue_e03.fm / 27.08.09
22
- All cables must be secured by means of suitable clamps (pull-relief) before entering the units.
- It must be ensured that cables do not block any moving parts within a unit.
- Power leads must be protected by "slow-blow" fuses according to their cross section.
- In the case of a unit whose cable inlet consists of a hole with brackets attached on the inside
and outside, the cable must be dressed as shown in
Figure 3-1.
Fig. 3-1 Cable inlet consisting of a hole with brackets
3.1.1.1
Maximum Cable Length
Coaxial Antenna Cable for the VHF Antenna
The maximum length of this cable (LCF 12-50) is 80 m. See Section 9,
Cabling Documents
.
Coaxial Cable for the GPS Antenna
The length of this cable is defined by the cable sets. Prefabricated cables with a length of 20, 30, or 40 m
can be delivered.
If a length of more than 40 m is needed, the cable LCF 12-50 of the VHF antenna must be used in combi-
nation with TNC-N plug adapters. See Section 9,
Cabling Documents
.
Ethernet LAN
The Ethernet LAN thin wire cabling (RG-213/U ship’s cable or RG58) must not exceed a length of 185 m.
Screen braid laid back over outer sheathing;
contact with the brackets via metal clamp
Installation cables
FMGCH,
FMKHC MGCH etc.
z_ue_072.gif
Metal clamp inside
Metal clamp outside
35
+5
Brackets