Technical Manual Automatic Identification System AIS 3410 Electronics Unit Item No.: ED3047G842 Revision: 01 (2009-08) Order No.
© SAM Electronics GmbH 2009 This document is our property for which we reserve all rights, including those relating to patents or registered designs. It must not be reproduced or used otherwise or made available to any third party without our prior permission in writing. Alterations due to technical progress are reserved. SAM Electronics GmbH D - 22763 Hamburg Service Customer Support Center Phone: + 49 (0) 18 03 00 85 53 Fax: + 49 (0) 18 03 00 85 54 E-mail: shipservice@sam-electronics.de t_ue_eti.
AIS 3410, Electronics Unit Technical Manual List of Contents List of Contents 1 1.1 1.2 1.3 2 2.1 2.2 2.3 2.4 2.5 2.6 2.7 2.8 2.
AIS 3410, Electronics Unit List of Contents Technical Manual 4.3.3 4.3.4 GPS Antenna Pilot Port 43 43 5 5.1 5.2 5.3 Setting-to-Work/Configuration Setting-to-Work Software Versions Configuration 45 45 45 45 5.3.1 5.3.2 5.3.3 Configuration with RADARPILOT/CHARTRADAR/MULTIPILOT 1000/1100 - NACOS xx-4/5 Systems Configuration with CHARTPILOT 93xx in NACOS xx-3 Systems Configuration with Radar 9xxx 45 46 46 5.4 5.5 6 6.
AIS 3410, Electronics Unit Technical Manual List of Figures List of Figures Fig. 2-1 Fig. 2-2 Fig. 2-3 Fig. 2-4 Fig. 2-5 Fig. 2-6 Fig. 2-7 Fig. 2-8 Fig. 2-9 Fig. 3-1 Fig. 3-2 Fig. 3-3 Fig. 3-4 Fig. 3-5 Fig. 4-1 Fig. 4-2 Fig. 4-3 Fig. 4-4 Fig. 4-5 Fig. 4-6 Fig. 4-7 Fig. 5-1 Fig. 6-1 Fig. 6-2 Fig. 6-3 Fig. 6-4 Fig. 6-6 Fig. 9-1 Fig. 9-2 Fig. 9-3 Fig. 9-4 Fig. 9-5 Fig. 9-6 Fig. 9-7 Fig. 9-8 Fig. 9-9 Fig. 9-10 Fig. 10-1 Fig. 10-2 Fig. 10-3 Fig.
AIS 3410, Electronics Unit List of Figures 6 Technical Manual ED3047G842 / 01 (2009-08) t_ue_eAV.fm / 27.08.
AIS 3410, Electronics Unit List of Abbreviations Technical Manual List of Abbreviations This list also contains abbreviations which are not used in this manual but in additional documentation.
List of Abbreviations AIS 3410, Electronics Unit Technical Manual 8 ED3047G842 / 01 (2009-08) t_ue_eak.fm / 27.08.
AIS 3410, Electronics Unit Technical Manual 1 1 General 1.1 Software Releases General This Technical Manual is the technical reference manual for the following components: - AIS 3410 Electronics Unit The manual contains further information about the antennas (GPS, VHF). 1.1 Software Releases This manual is valid for all software versions of the AIS 3410. See also Section 5.2. 1.
1 General 1.3 Safety Warnings AIS 3410, Electronics Unit Technical Manual Boards and units that contain ESD-endangered semiconductors are marked with the symbol shown above. All assisting persons who might come into contact with the endangered boards must also use the ESD equipment. DANGER It is not permissible to connect the ship’s mains to the system before setting-to-work by a qualified technician. The mains must be switched off (e.g.
AIS 3410, Electronics Unit Technical Manual 2 2 Overview 2.1 Compatibility with Other Systems Overview The 3410 is an AIS Electronics Unit which receives data from other vessels by means of a VHF radio and sends these data to the radar/navigation system. In the opposite direction, the AIS receives data from the radar/navigation system and the ship’s sensors and transmits these data by means of the VHF radio.
AIS 3410, Electronics Unit 2 Overview Technical Manual 2.2 AIS 3410 in RADARPILOT 1000/1100 Systems 2.2 AIS 3410 in RADARPILOT 1000/1100 Systems Fig.
AIS 3410, Electronics Unit 2 Overview Technical Manual 2.3 AIS 3410 in 1000/1100 Series Systems (NACOS xx-4 and xx-5) 2.3 AIS 3410 in 1000/1100 Series Systems (NACOS xx-4 and xx-5) SAM SAM VHF Antenna GPS Antenna Ship's sensor data RS 422 Ship's sensor data Display Electronics Unit CAN Bus Interconnection Box Ship's sensor data Ethernet LAN RS 422 Display Electronics Unit Interconnection Box with Analog Prim.
AIS 3410, Electronics Unit 2 Overview Technical Manual 2.4 AIS 3410 in CHARTPILOT Stand-alone Systems 2.4 AIS 3410 in CHARTPILOT Stand-alone Systems * Gyro: HDT, ROT Speedlog (bottom-track): VBW Position Sensor: GLL, VTG VHF Antenna All data are transferred with a repetition rate of 1 Hz (IEC 61162-1) GPS Antenna ** except for CHARTPILOT 9300 with Electronics Unit GE3022 Ship's sensor data RS422 z_ue_008odcu.
AIS 3410, Electronics Unit 2 Overview Technical Manual 2.5 AIS 3410 in NACOS xx-3 Systems (Radar 9xxx and CHARTPILOT) 2.5 AIS 3410 in NACOS xx-3 Systems (Radar 9xxx and CHARTPILOT) SAM SAM VHF Antenna Transceiver Transceiver Ship's sensor data Ship's Interface Electronics Unit GPS Antenna CAN 1 Ship's sensor data Ship's sensor data 1 Sensor Input 2 3 Channels ** Electronics Unit AIS Electronics Unit RS422 24 VDC CHARTPILOT 93xx * ** MULTIPILOT 910x Ethernet LAN * z_ue_009.
AIS 3410, Electronics Unit 2 Overview Technical Manual 2.6 AIS 3410 in Radar 9xxx Systems with RADARPILOT 1000/1100 2.6 AIS 3410 in Radar 9xxx Systems with RADARPILOT 1000/1100 SAM SAM Display Electronics Unit VHF Antenna GPS Antenna Transceiver Ship's sensor data Ship's Interface CAN 1 Ship's sensor data Interconnection Box with Analog Interface RS422, Primary Display Port Electronics Unit 1 Sensor Input 2 3 Channels ** RS422 AIS Electronics Unit 24 VDC RS422 z_ue_010.
AIS 3410, Electronics Unit 2 Overview Technical Manual 2.7 AIS 3410 in Radar 9xxx Systems 2.7 AIS 3410 in Radar 9xxx Systems SAM SAM VHF Antenna Transceiver Ship's sensor data Ship's Interface GPS Antenna Transceiver Ship's sensor data RS422 CAN 1 Electronics Unit Electronics Unit 1 Sensor Input 2 Channels* 3 AIS 34x0 24 VDC z_ue_044odcu.pdf Radar 9xxx Ship's mains Fig.
AIS 3410, Electronics Unit 2 Overview Technical Manual 2.8 Housing of the 3410 Electronics Unit 2.8 Housing of the 3410 Electronics Unit Fig. 2-7 AIS 3410 Electronics Unit (current version) z_ue_012.tif z_ue_037.jpg The plastic housing of the 3410 contains a single Electronics Unit which consists of the controller, the interfaces, the VHF transmitter/receiver and the GPS receiver.
AIS 3410, Electronics Unit Technical Manual 2 Overview 2.9 Replacement of AIS Electronics Unit 2.9 Replacement of AIS Electronics Unit In case of replacing the UAIS DEBEG 3400 Electronics Unit with a AIS 3410 Electronics Unit there is no need to remove the old housing. Therefore proceed as described below. To ensure the correct display of all data please refer to Technote T-0908-3400-023. 2.9.1 Open the Housing of AIS 3410 1. Remove these parts from the AIS 3410. 2.
AIS 3410, Electronics Unit 2 Overview Technical Manual 2.10 Media Converter Installation (necessary for ships with BNC LAN networks) 2.9.3 Merge the AIS 3410 Electronics Unit into the UAIS DEBEG 3400 Housing 1. 2. 3. 4. Insert the Electronics Unit from the AIS 3410 and mount it on the distance bolts with the six M6 nuts. Take the new Phoenix plug (connector 4) and connect the cables again. Connect to the 24V interface the cables from24V power supply, fan and media converter.
AIS 3410, Electronics Unit 3 Installation Recommendations Technical Manual 3 3.1 General Recommendations Installation Recommendations 3.1 General Recommendations 3.1.1 Cables Cable types, cable data, maximum cable length, special instructions for cable laying and connection details are defined in the Cabling Documents of the corresponding equipment (consisting of schematic diagram, remarks, cable list and connection diagram).
AIS 3410, Electronics Unit 3 Installation Recommendations Technical Manual 3.1 General Recommendations - All cables must be secured by means of suitable clamps (pull-relief) before entering the units. - It must be ensured that cables do not block any moving parts within a unit. - Power leads must be protected by "slow-blow" fuses according to their cross section.
AIS 3410, Electronics Unit 3 Installation Recommendations Technical Manual 3.1 General Recommendations 3.1.1.2 Cable Sets The following cable sets are available: Purpose/Description Quantity/m Order No. LAN network, cable RG 213/U, 2 BNC connectors on request 300005394 Connection of the GPS antenna, cable HF2,3LZ/7,3DZ with 2 plugs 11TNC-50-72C 20 271256324 Connection of the GPS antenna, cable 02Y(ST)C2Y2.7/7.3AF with 2 TNC plugs 30 300005391 Connection of the GPS antenna, cable 02Y(ST)C2Y2.
3 Installation Recommendations 3.2 Specific Recommendations AIS 3410, Electronics Unit Technical Manual This distance is measured from the centre of the magnetic system of the compass to the nearest point on the corresponding unit concerned. - Units which are to be used on the bridge wing must be installed inside the "wing control console" protected against the weather - if they do not at least correspond to the enclosure type IP 56. In order to avoid misting of the viewing screen, 25 ...
AIS 3410, Electronics Unit 3 Installation Recommendations Technical Manual 3.2 Specific Recommendations 3.2.2 Recommendations Concerning the Installation of the Electronics Unit The Electronics Unit should be mounted on a vertical bulkhead. A distance of at least 300 mm from other devices must be ensured around the housing for sufficient air circulation. See also Section 10, O u t l i n e Drawings. 3.2.
AIS 3410, Electronics Unit 3 Installation Recommendations Technical Manual 3.2 Specific Recommendations 3.2.3.1 Recommendations Concerning the Installation of the VHF Antenna Superstructures, e.g. deck house, funnel, Mast, boom, railing with small diameter (should be avoided) >2 m z_ue_041.eps >2 m Fig.
AIS 3410, Electronics Unit 3 Installation Recommendations Technical Manual 3.2 Specific Recommendations 3.2.3.2 Recommendations Concerning the Installation of the GPS Antenna GPS Satellites Superstructures, e.g. deck house, funnel, Mast, boom with small diameter Superstructures, e.g. deck house, funnel z_ue_043.eps Fig. 3-4 360° view GPS Antenna Side view Top view Positioning of the GPS Antenna 25° SAM z_ue_042.eps GPS Antenna Fig.
3 Installation Recommendations AIS 3410, Electronics Unit Technical Manual 3.2 Specific Recommendations 3.2.4 Recommendations Concerning Redundancy If possible, the Electronics Unit should be supplied with the ship’s sensor data from two different sources, e.g. in a dual installation with RADARPILOT 1000 or 1100 the AIS can be supplied with sensor data from both radars.
AIS 3410, Electronics Unit 3 Installation Recommendations Technical Manual 3.2 Specific Recommendations 3.2.8 Recommendations Concerning AIS Stand-alone with Radar 9xxx / NACOS xx-2/-3 An AIS 3410 can be used with an existing Radar 9xxx installation without any additional software update if the following prerequisites are fulfilled: - All necessary ship’s sensors are connected additionally to the AIS Electronics Unit. The sensors must be connected directly (a Gyro Converter Unit may be necessary).
3 Installation Recommendations 3.2 Specific Recommendations 30 AIS 3410, Electronics Unit Technical Manual ED3047G842 / 01 (2009-08) t_ue_e03.fm / 27.08.
AIS 3410, Electronics Unit 4 Functional Description Technical Manual 4 4.1 Block Diagram Functional Description The AIS system consists of the following components: - AIS 3410 Electronics Unit - GPS antenna 1330FW - VHF antenna CXL 2-1 The functionality is described in Section 4.1 by means of the block diagram (Figure 4-3). 4.1 Block Diagram VHF Antenna Ship's sensor data Radar / NACOS system Primary Display Port (PDP) 3 x RS422 z_ue_015.
AIS 3410, Electronics Unit 4 Functional Description Technical Manual 4.2 Termination The VHF transmitter/receiver has a limited range. By means of the connection of a long range communication system (such as a satellite communication system) to the long range port, this limitation can be eliminated. In this way, the AIS can be called to send the ship’s data. The requested data are sent via the long range port and the long range communication system to the questioner.
AIS 3410, Electronics Unit 4 Functional Description Technical Manual 4.3 Description of the Components 4.3 Description of the Components 4.3.
AIS 3410, Electronics Unit 4 Functional Description Technical Manual 4.3 Description of the Components 4.3.1.
AIS 3410, Electronics Unit 4 Functional Description Technical Manual 4.3 Description of the Components 4.3.1.2 Internal Connectors GPS LAN (RJ-45) VHF Fig. 4-5 Internal connectors For retrofit of older housings (UAIS DEBEG 3400) refer to Section 2.9. Installation of the Media Converter refer to Section 2.10. 4.3.1.3 Supported Sensor Input Sentences Prerequisites: NMEA Version 2.01 edition 04/1994 (corresponds to the first edition of IEC 61162) or higher is required.
AIS 3410, Electronics Unit 4 Functional Description Technical Manual 4.
AIS 3410, Electronics Unit 4 Functional Description Technical Manual 4.3 Description of the Components 4.3.1.4 Supported Sentences for the AIS Primary Display Port and the Pilot Port Input Input sentences in compliance with IEC 61162-1/-2 Data Sentence Identifier/Description Normal Access - Parameter Entry Voyage information: - Vessel type and cargo category - Navigational status - Draught, max.
AIS 3410, Electronics Unit 4 Functional Description Technical Manual 4.
AIS 3410, Electronics Unit Technical Manual 4 Functional Description 4.
4 Functional Description AIS 3410, Electronics Unit Technical Manual 4.3 Description of the Components 4.3.1.6 Supported Sentences for the Internal Position Sensor Output Output sentences in compliance to IEC 61162-1, edition 3, 04/2007 (NMEA0183 version 3.01) 40 Data Sentence Identifier/Description Datum reference - Local datum (e.g.
AIS 3410, Electronics Unit 4 Functional Description Technical Manual 4.3 Description of the Components Data Sentence Identifier/Description Recommended minimum specific GNSS data - UTC (hhmmss.ss) - Status ("V" or "A") - Latitude, N/S (IIII.II,a) - Longitude, E/W (YYYYY.YY,a) - Speed over ground, knots (x.x) - Course over ground, degrees true (x.
AIS 3410, Electronics Unit 4 Functional Description Technical Manual 4.3 Description of the Components 4.3.1.8 Example for the Interconnection Gyro Interface 4901 TB 16 15 14 13 12 11 10 0 V +24 V AIS Electronics Unit 8 7 6 5 4 3 2 1 Pilot Por t 2 Prim. Displ. P.
AIS 3410, Electronics Unit 4 Functional Description Technical Manual 4.3 Description of the Components 4.3.3 GPS Antenna The GPS antenna 1330 is a GPS L1 antenna for a frequency of 1575.42 ±10 MHz with an integrated amplifier. For the technical data see Section 7.2.3, for installation instructions see Section 3. 4.3.4 Pilot Port The Pilot Port must be connected as prescribed in the regulations. The connector/cable kits are described in Section 3.2.7 on page 28.
4 Functional Description 4.3 Description of the Components 44 AIS 3410, Electronics Unit Technical Manual ED3047G842 / 01 (2009-08) t_ue_e04.fm / 27.08.
AIS 3410, Electronics Unit 5 Setting-to-Work/Configuration Technical Manual 5 5.1 Setting-to-Work Setting-to-Work/Configuration 5.1 Setting-to-Work 1. The AIS Electronics Unit and the antennas must be installed as described in Section 3 (I n s t a l l a t i o n R e c o m m e n d a t i o n s ). For information about the dimensions see Section 10 (O u t l i n e D r a w i n g s ). 2. The cabling and connection must be performed corresponding to the Cabling Documents in Section 9. 3.
5 Setting-to-Work/Configuration AIS 3410, Electronics Unit Technical Manual 5.4 Testing 5.3.2 Configuration with CHARTPILOT 93xx in NACOS xx-3 Systems It is necessary to configure the CHARTPILOT 93xx and the interfaces of the Ship’s Interface. For information in detail see the Technical Manual of the CHARTPILOT 93xx. 5.3.3 Configuration with Radar 9xxx It is necessary to configure the interfaces of the Ship’s Interface. For information in detail see the Service Manual of the Radar 9xxx Electronics Unit.
AIS 3410, Electronics Unit Technical Manual 6 6 Repair/Maintenance 6.1 Trouble Shooting Repair/Maintenance GENERAL: The jumper settings and switch settings on a replacement pcb must be the same as on the defective pcb. The wire connections must be made in exactly the same way. Exceptions are explained in this manual. 6.1 Trouble Shooting 6.1.1 Hints In the case of problems during setting-to-work, the cabling should be checked again. All components must be supplied with power.
AIS 3410, Electronics Unit 6 Repair/Maintenance Technical Manual 6.1 Trouble Shooting 6.1.2 Fault Tree Failure Description Unusual behaviour of AIS application AIS Offline Internal Clock lost No AIS data on Radar (Software version < 3.0.0) No AIS data on Radar (Software version > 3.0.0) No AIS data on ECDIS (Chartpilot, MP2 & 3) 48 Possible Causes Service Measure Spare Part No. Software hung up Reset Electronics Unit - Software failure caused e.g.
AIS 3410, Electronics Unit 6 Repair/Maintenance Technical Manual 6.1 Trouble Shooting Failure Description No AIS targets visible but no alarm messages are given Hot Housing No heading data No external GNSS data Possible Causes Service Measure Spare Part No.
AIS 3410, Electronics Unit 6 Repair/Maintenance Technical Manual 6.1 Trouble Shooting 2. Connect the AIS output TB14 and TB15 of the Analog Interface additionally to an indicator serial interface (TB1) of the radar. If there is a free input, this one should be used. If all inputs are used, one of them must be disconnected. Figure 6-1 shows the connection to the serial interface No. 4 as an example. Primary Display Port RADARPILOT/CHARTRADAR MULTIPILOT 1000/1100 z_ue_025.
AIS 3410, Electronics Unit 6 Repair/Maintenance Technical Manual 6.1 Trouble Shooting Alive message, sent every 15 seconds Voyage Data has been modified at the Indicator. $PSAEAISALV*07 $RAVSD,69,12.0,0,BREMEN,142000.
AIS 3410, Electronics Unit 6 Repair/Maintenance Technical Manual z_ue_026.eps 6.1 Trouble Shooting Primary Display Port RADARPILOT/CHARTRADAR 1000/1100 AIS Electronics Unit Analog Interface TB 10 AIS RxD, Input 11 AIS RxD, Input + 14 AIS TxD, Output 15 AIS TxD, Output + 16 GND Connector 2 8 Output 7 Output + 6 Input 5 Input + 1 GND Interconnection Board TB1 Indicator Serial Interface 4 16 RxD4, Input + 17 RxD4, Input - Fig. 6-3 3.
AIS 3410, Electronics Unit 6 Repair/Maintenance Technical Manual 6.1 Trouble Shooting Status messages of the connected sensors, sent every minute Position report Alive message, every second Another AIS has been received Alarm: External position data not available Alarm: Heading data not available Fig.
AIS 3410, Electronics Unit 6 Repair/Maintenance Technical Manual 6.2 Test of the Antenna Performance 6.1.3.2 Indication: System Fault Message 3616 Displayed on Indicator If the system fault message 3616 is displayed, it is likely that the problems are caused by the Analog Interface if the AIS is connected via the Primary Display Port. Procedure: 1. Check the configuration of the Analog Interface. See the Technical Manual of the RADARPILOT 1000/1100 for further information. 2.
AIS 3410, Electronics Unit 6 Repair/Maintenance Technical Manual 6.3 Software Update You are now requested to fill in your username and password. Afterwards you are redirected to the folder with the newest zip file containing the software for all components of the AIS system. The unpacked zip file can be saved on a CD ROM. It is not permissible to modify any settings in the SAM-CMIS system. To leave the system click on Tools -> Log-out.
6 Repair/Maintenance 6.3 Software Update AIS 3410, Electronics Unit Technical Manual Connection at the Electronics Unit The cable must be connected to the serial service interface of the computer and to the connector on the top of the Electronics Unit’s port Service Interface Fig. 6-6 Service Interface 6.3.4 Software Update by means of a Laptop 1. Disconnect the Electronics Unit from the power supply for about 5 s. 2.
AIS 3410, Electronics Unit 6 Repair/Maintenance Technical Manual 6.3 Software Update A status windows appears during the update. 8. It must be waited until the message "Flash programming finished, system is rebooting" appears. 9. The Electronics Unit reboots automatically. The OK button closes the window of the update routine. z_ue_053.jpg 7. 10. Verify the proper function of the system, make sure that AIS targets and sensor data will be displayed on the connected display system. 11.
6 Repair/Maintenance AIS 3410, Electronics Unit Technical Manual 6.4 Opening the Housing 6.4 Opening the Housing Opening of the Electronics Unit housing of AIS 3410 Undo the four screws in the cover. To close the housing, proceed in the reverse order. 6.4.1 Fuses Electronics Unit The Electronics Unit contains no fuses. 6.4.2 Antennas If one of the antennas is defective, it must be exchanged. See the Spare Part List for the order number. 6.
AIS 3410, Electronics Unit 7 Technical Data Technical Manual 7.1 Conformity to Standards, Environmental Conditions 7 Technical Data 7.1 Conformity to Standards, Environmental Conditions The AIS 3410 Electronics Unit is complient with DIN EN 60945 (Maritime navigation and radiocommunication equipment and systems - General requirements - Methods of testing and required test results). The Electronics Unit belongs to the category "protected from the weather".
AIS 3410, Electronics Unit 7 Technical Data Technical Manual 7.2 Performance 7.2.2 Performance Data of the VHF Antenna CLX 2-1/150-170 MHz Antenna type: Frequency: Impedance: Polarization: Gain: Bandwith: SWR: Max. power: Connector: Wind load: Material: Colour: Total length: Weight: Mounting: ½λ coaxial, broad band 150...170 MHz Nom. 50 Ω Vertical 2 dBi, 0 dBd 20 MHz < 1.5 150 W TNC female 21.8 (at 150 km/h) Whip = Glassfibre Marine white Approx. 1.2 m Approx. 340 g 1" threaded mast tube z_ue_408.
AIS 3410, Electronics Unit 7 Technical Data Technical Manual 7.2.3 7.3 Dimensions and Weights Performance Data of the GPS Antenna General: Color: Weight: Nominal RF input: Operating temperature: Humidity: White 163 g TNC female -40...+85°C 95% relative humidity Antenna Element: Frequency: Impedance: Nominal VSWR: Polarization: Gain: 1575.42 ±10.0 MHz 50 Ω 1.5:1 max. Right hand circular +4.5 dBiC nom. Low Noise Amplifier: Frequency: Impedance: Nominal output VSWR: Max.
7 Technical Data 7.4 Compass Safe Distances 62 AIS 3410, Electronics Unit Technical Manual ED3047G842 / 01 (2009-08) t_ue_e08.fm / 27.08.
AIS 3410, Electronics Unit 8 Fault Code List Technical Manual 8 Fault Code List The following fault codes (integrity alarm conditions) can be displayed at the connected display unit (for example a RADARPILOT 1000/1100). See also Section 6 from page 47 on for further information.
AIS 3410, Electronics Unit 8 Fault Code List Technical Manual Messages at Fault 029 030 032 1000/1100 Series, CHARTPILOT, MULTIPLOT 910x (Chart Mode) AIS: No valid SOG information AIS: No valid COG information AIS: Heading lost/ invalid 035 AIS: No valid ROT information 051 AIS: Channel management information not accepted 052 053 64 AIS: GPS receiver fault AIS: GPS antenna not connected or defective Radar 9xxx, MULTIPILOT 910x (Radar Mode) Error Message generated by, Possible Cause/Sour
AIS 3410, Electronics Unit 8 Fault Code List Technical Manual Messages at Fault 054 0204 - 1000/1100 Series, CHARTPILOT, MULTIPLOT 910x (Chart Mode) Radar 9xxx, MULTIPILOT 910x (Radar Mode) Error Message generated by, Possible Cause/Source, Reaction of the System, Remedy AIS: GPS antenna short circuit Generated by: AIS Electronics Unit. CauseSource: Short circuit in the cable/connectors or within the GPS antenna.
8 Fault Code List AIS 3410, Electronics Unit Technical Manual 66 ED3047G842 / 01 (2009-08) t_ue_e09.fm / 27.08.
AIS 3410, Electronics Unit 9 Cabling Documents Technical Manual 9 Cabling Documents Grounding All components of the system have contacts such as bolts or terminals for grounding. Grounding is important for EMC purposes as well as for protecting people’s lives. Both purposes are covered by the standard grounding of the system’s housings to the ship’s metallic structure (bolted or welded). Regardless of the type of ship’s grounding (e.g.
9 Cabling Documents AIS 3410, Electronics Unit Technical Manual Fig. 9-1 68 Cable Diagram, connection to RADARPILOT 1x00, NACOS xx-4/5 via Primary Display Port ED3047G842 / 01 (2009-08) t_ue_e11.fm / 27.08.
AIS 3410, Electronics Unit 9 Cabling Documents Technical Manual Fig. 9-2 Cable Diagram, connection to CHARTPILOT, NACOS xx-4/5, RADAR / MULTIPILOT 1x00 via LAN ED3047G842 / 01 (2009-08) t_ue_e11.fm / 27.08.
9 Cabling Documents AIS 3410, Electronics Unit Technical Manual Fig. 9-3 70 Cable Diagram, connection to CHARTPILOT stand-alone ED3047G842 / 01 (2009-08) t_ue_e11.fm / 27.08.
AIS 3410, Electronics Unit 9 Cabling Documents Technical Manual Fig. 9-4 Cable Diagram, connection to Radar 9xxx via Radar 9xxx AIS Interface (NACOS xx-3) ED3047G842 / 01 (2009-08) t_ue_e11.fm / 27.08.
9 Cabling Documents AIS 3410, Electronics Unit Technical Manual Fig. 9-5 72 Detailed Cable Diagram, connection to RADARPILOT 1x00, NACOS xx-4/5 via Primary Display Port ED3047G842 / 01 (2009-08) t_ue_e11.fm / 27.08.
AIS 3410, Electronics Unit 9 Cabling Documents Technical Manual Fig. 9-6 Detailed Cable Diagram, Wheelhouse Console ED3047G842 / 01 (2009-08) t_ue_e11.fm / 27.08.
9 Cabling Documents AIS 3410, Electronics Unit Technical Manual Fig. 9-7 74 Detailed Cable Diagram, connection to NACOS xx-4/5, RADAR / MULTIPILOT 1x00 via LAN ED3047G842 / 01 (2009-08) t_ue_e11.fm / 27.08.
AIS 3410, Electronics Unit 9 Cabling Documents Technical Manual Fig. 9-8 Detailed Cable Diagram, connection to CHARTPILOT stand-alone systems ED3047G842 / 01 (2009-08) t_ue_e11.fm / 27.08.
9 Cabling Documents AIS 3410, Electronics Unit Technical Manual Fig. 9-9 76 Detailed Cable Diagram, connection to RADAR 9xxx AIS Interface ED3047G842 / 01 (2009-08) t_ue_e11.fm / 27.08.
AIS 3410, Electronics Unit 9 Cabling Documents Technical Manual Fig. 9-10 Detailed Cable Diagram, connection to RADAR 9xxx AIS Interface PCB GE 3044 G 220 ED3047G842 / 01 (2009-08) t_ue_e11.fm / 27.08.
9 Cabling Documents AIS 3410, Electronics Unit Technical Manual 78 ED3047G842 / 01 (2009-08) t_ue_e11.fm / 27.08.
AIS 3410, Electronics Unit 10 Outline Drawings Technical Manual 10 Outline Drawings Title Page AIS 3410 Outline Drawing 79 AIS GPS antenna, 1/2 80 AIS GPS antenna, 2/2 81 AIS VHF antenna 82 ONLY BULKHEAD MOUNTING Grounding M6 120 Area for cable inlet 320 Space required for service 300 ca. 200 168 184 142 6,5 ca. 700 Cover not shown Min. distance from: Standard compass: 0.4 m Steering compass: 0.3 m Protection category: IP22 Weight: 3kg Fig.
AIS 3410, Electronics Unit 10 Outline Drawings Technical Manual z_ue_402.pdf All dimensions are indicated as inches. Fig. 10-2 AIS GPS antenna, 1/2 80 ED3047G842 / 01 (2009-08) t_ue_e12.fm / 27.08.
AIS 3410, Electronics Unit 10 Outline Drawings z_ue_403.pdf Technical Manual Fig. 10-3 AIS GPS antenna, 2/2 ED3047G842 / 01 (2009-08) t_ue_e12.fm / 27.08.
10 Outline Drawings AIS 3410, Electronics Unit Technical Manual Fig. 10-4 AIS VHF antenna 82 ED3047G842 / 01 (2009-08) t_ue_e12.fm / 27.08.
AIS 3410, Electronics Unit Notes Technical Manual Notes Space for your notes. ED3047G842 / 01 (2009-08) t_ue_eno.fm / 27.08.
Notes AIS 3410, Electronics Unit Technical Manual 84 ED3047G842 / 01 (2009-08) t_ue_eno.fm / 27.08.
